Atlantis Land A02-RA ME01 manuale d’uso

I-Storm ADSL Router With Firewall Built-in User’s Manual[...]

[...]

i COPYRIGHT The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other nam es mentioned mat be trademarks or registered tradem arks of their respective owners. S ubject to change without notice. No liability for technical errors and/or omissions. Copyright  2002 by this com pany. DISCLAIMER This company makes no representat[...]

Atlantis Land I-STORM ADSL ROUTER ii Table of Content CHAPTER 1 .......................................................................... 1 I NTRODUCTION ................................................................................................................................... 1 1.1 An Overview of I-STORM ADSL ROUTER ......................[...]

Chapter 1 Introduction iii T ROUBLESHOOTING ......................................................................................................................... 50 Problems Starting Up the I-STORM ADSL ROUTER ............................................................ 50 Problems with the WAN Interface ........................................[...]

[...]

1 Chapter 1 Introduction 1.1 An Overview of I-STORM ADSL ROUTER The Atlantis Land I-STORM ADSL ROUTER rout er provides a high-speed ADSL port and an Ethernet port for high-speed Internet browsing. It can support downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1024Kbps. It also supports rate management that allo[...]

Atlantis Land I-STORM ADSL ROUTER 2 dedicated local web server, even though the server now has a diffe rent IP address. In this example, the product is on the Internet and vulne rable to attacks, but th e server is protected. Virtual Service can also be used to re-task servic es to multiple servers. For instance, the product can be set to allow sep[...]

Chapter 1 Introduction 3 Virtual Private Network (VPN): Allow user to m ake a tunnel with remote site d irectly to secure the data transmission among the conne ction. User can use em bedded PPTP client supported by this router to make a VPN connecti on. Or user can run the PP TP client in PC and the router already provides IPSec and PPTP pa ss thro[...]

Atlantis Land I-STORM ADSL ROUTER 4 1.4 I-STORM ADSL ROUTER Application A) Connect WAN port ( LINE ) to the phone line by RJ11 cable (into packing) B) L’I-Storm Router ADSL can be connect, by RJ45 port ( LAN ), like instructions: 1. Directly to the PC, by CAT 5 crossover cable (into packing). 2. To Hub/Switch into UPLINK port by CA T 5 crossover [...]

5 Chapter 2 Using I-STORM ADSL ROUTER 2.1 Cautions for using I-STORM ADSL ROUTER Do not place I-STORM ADSL ROUTER under high humidity and high temperature. Do not use the same power source for I-STORM ADSL ROUTER with other equipment. Do not open or repair the case yourself. If I-STORM ADSL ROUTER is too hot, turn off the power immediately and have[...]

Atlantis Land I-STORM ADSL ROUTER 6 2.3 The Rear Ports Port Meaning 1 Power (jack) Connect the supplied power adapter to this jack. 2 LAN (RJ-45 connector) Connect a straight Ethernet cable to this port when connecting to a LAN such as an office or home network. Connect the supplied crossover cable to this port when connecting to a LAN card. 3 RS-2[...]

7 Chapter 3 Configuration I-STORM ADSL ROUTER can be configured with your Web browser. The web browser is included as a standard application in following ope ration systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me, etc. The produc t provides a very easy and us er-friendly interface for configuration. 3.1 Before Configuration This section desc[...]

Atlantis Land I-STORM ADSL ROUTER 8 Configuring PC in Windows 95/98/ME 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible , or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties . 4. Select the IP Address ta[...]

Chapter 3 Configuration 9 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration. Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Proper[...]

Atlantis Land I-STORM ADSL ROUTER 10 3. Select the Obtain an IP address from a DHCP server radio button and click OK . Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Network and Dial-up Connections . 2. Double-click LAN Area Connection .[...]

Chapter 3 Configuration 11 3. In the LAN Area Connection Status window, click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Atlantis Land I-STORM ADSL ROUTER 12 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View) . In the Control Panel, double-click on Network Connections. 2. Double-click Local[...]

Chapter 3 Configuration 13 3. In the LAN Area Connection Status window, click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Atlantis Land I-STORM ADSL ROUTER 14 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 3.2 Factory Default Settings Before you configure this I-STORM ADSL ROU TER , you need to know the following default settings. 1. Web Configurator Password : &l[...]

Chapter 3 Configuration 15 3.2.1 Router/Bridge Mode The default mode is Router Mode . If you want to switch between the two modes, click on Advanced → Router/Bridge Mode in the left pane. Select the mode you want to use, and then click the “Apply” button. 3.2.2 Password The password is left blank as the default setting. When configur ing your[...]

Atlantis Land I-STORM ADSL ROUTER 16 3.3 Information from ISP Before you start configuring this device, you have to check with your ISP what kind of service is provided such as PPPoE, PPPoA, RFC1483, IPoA, or PPTP-to-PPPoA Relaying. Gather the information as illustrated in th e following table and k eep it fo r reference. PPPoE VPI/VCI, VC-based/LL[...]

Chapter 3 Configuration 17 At the configuration homepage, the left navi gation pane where bookmarks are provided links you directly to the desire d setup page, including LAN, WAN, System, Firewall, VPN, Virtual Server, Advanced, Status, Help and Logout . Click on the desired item to expand the page in the main navigation pane. 3.4.1 LAN This screen[...]

Atlantis Land I-STORM ADSL ROUTER 18 IP Address IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan to ch ange it to another IP address to a different range of IP subnet. Please make sure your PC is al so located at the same IP subnet. Otherwise, you may not be able to access the ADSL Router. Subnet Mask: De[...]

Chapter 3 Configuration 19 ~ Disable: Check to disable I-STORM ADSL ROUTER to distribute IP Addresses to the local network. If you check th is selection, Disable , remember to specify a static IP address, subnet Mask, and DNS setting for each of your local computers. Be careful no t to assign the same IP address to different computers. ~ Enable: Ch[...]

Atlantis Land I-STORM ADSL ROUTER 20 PPPoE PPPoE (PPP over Ethernet) is known as a dial-up DSL or cable service. It is designed to integrate the broadband services into the current widely de ployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Theref ore, users can get greater acc ess speed without changing the operation conc[...]

Chapter 3 Configuration 21 PPPoA NAT: The NAT feature allows multiple users to acce ss Internet through a singl e IP account, sharing the single IP address from ISP. If users in th e LAN site have public IP addresses and can access Internet directly, the NAT function can be disabled. Username: Enter the username provided by your ISP. Maximum input [...]

Atlantis Land I-STORM ADSL ROUTER 22 RFC1483 Configure this WAN interface with a specific IP address. This IP address should be given from ISP directly. NAT: The NAT feature allows multiple users to acce ss Internet through a singl e IP account, sharing the single IP address from ISP. If users in th e LAN site have public IP addresses and can acces[...]

Chapter 3 Configuration 23 IPoA Configure this WAN interface with a specific IP address. This IP address should be given from ISP directly. NAT: The NAT feature allows multiple users to acce ss Internet through a singl e IP account, sharing the single IP address from ISP. If users in th e LAN site have public IP addresses and can access Internet di[...]

Atlantis Land I-STORM ADSL ROUTER 24 It can be used to connect and establish a PPTP tunnel between PPTP client on LAN and router. The router will convert and map the PPTP packet from/to PPP packet. Router establishes a PPPoA connection with ISP. DNS A Domain Name System (DNS) contains a mapping table for domain name and IP address. In the Internet,[...]

Chapter 3 Configuration 25 3.4.3 System Password In factory setting, there is no password prot ection when user accesses I-STORM ADSL ROUTER . It is recommended that you change the default password <BLANK> to ensure that someone cannot adjust your settings without your permission. <BLANK> means there is no password. Every time you chang[...]

Atlantis Land I-STORM ADSL ROUTER 26 Time Zone The router does not have a real time clock on board; instead, it uses the simple network tim e protocol (SNTP) to get the current time fr om the SNTP server in outsid e network. Please choose your local time zone and click Apply button. You will get the co rrect time information afte r you really estab[...]

Chapter 3 Configuration 27 Then, click “Upgrade” to start upgrading. When the procedure is com pleted, the router will reset automatically to make the new firmware work. Factory Setting If for any reason you have to reset this I-STORM ADSL ROUTER factory default settings, be careful that the current settings will be lost and the settings are re[...]

Atlantis Land I-STORM ADSL ROUTER 28 button. Each time you reboot your I-STORM ADSL ROUTER , the following figure will appear. Please wait 25 seconds for auto-reconnection. 3.4.4 Firewall User can decide to enable this firewall function including Packet Filter, Bl ock Hacker Attack, and Block WAN request features for better security control or not.[...]

Chapter 3 Configuration 29 This configuration program allows you to set up di fferent filter rules up to 20 for different users based on their IP addresses or their network Po rt num ber. The relationship am ong all filters is “or” operation, which means the rout er checks these different f ilter rules one by one, stating from the first rule. A[...]

Atlantis Land I-STORM ADSL ROUTER 30 Active: Choose “Yes” to enable the rule, or choose “No” to disable the rule. Packet Type: Specify the packet type (TCP, UDP, ICMP or any) that the rule will be applied to. Select TCP if you want to scope for the connection- based application se rvice on the remote server using the port number. Or select [...]

Chapter 3 Configuration 31 - IP Spoofing - Ping of Death (Length > 65535) - Land Attack (Same source / destination IP address) - IP with zero length - Sync flooding - Smurf Attack (ICMP Echo with x.x.x.0 or x.x.x.255) - Snork Attack - UDP port loop-back - TCP NULL scan Block WAN Request/URL Filter Check “Enable” if you want to exclude out si[...]

Atlantis Land I-STORM ADSL ROUTER 32 3.4.5 VPN VPN (Virtual Private Network) is a secured and Inte rnet protocol to allow us ers to access the co mpany internal network resources outside the company network. If you want to make this function take effect, check the “Enable” button. Hence, the following fields will be activated. Username: Enter t[...]

Chapter 3 Configuration 33 3.4.6 Virtual Server Being a natural Internet f irewall, I-STORM ADSL ROUTER protects yo ur network from being accessed by outside users. When it needs to allow out side users to access internal servers, e.g. Web server, FTP server, E-mail server or News server, th is product can act as a vi rtual server. You can set up a[...]

Atlantis Land I-STORM ADSL ROUTER 34 3.4.7 Advanced Remote Config Check “Enable” if you want to configure your I- STORM ADSL ROUTER from any PC in the Internet world with a web browser. To configure this router remotely, use the URL ”http://WAN IP address:33659” where WAN IP address is the IP address of the router’s WAN port. You ca n fin[...]

Chapter 3 Configuration 35 Dynamic Routing The dynamic routing function of th e router can be used to allo w the router to automatically adjust to physical changes in the network’s layo ut. The router uses the dynamic RIP protocol. It regularly broadcasts routing information to ot her routers on the networ k. Choose the protocol ─ RIP1, RIP2, o[...]

Atlantis Land I-STORM ADSL ROUTER 36 Add: Click this button to add a new static routing. When you click this button, the next figure appears. Edit: Check the item you want to ed it. Then, click the “Edit” button. Delete: Check the item you want to dele te. Then, click the “Delete” button. Destination Subnet / Subnet Mask / Gateway Address: [...]

Chapter 3 Configuration 37 3.4.8 Status System Status Display the current LAN, WAN, and ADSL connection status. The first line under the WAN segm ent displays the WAN-ISP protoc ol you set. You can see the status of connection from its right-side column. As for “PPPoE” and “PPPoA” prot ocol, the right column seems so me kind different. Ther[...]

Atlantis Land I-STORM ADSL ROUTER 38 Device Info Display the current Firmware version and MA C address of your I-STORM ADSL ROUTER . System Logs Display the system logs cum ulated till the presen t time. You can trace the historical in formation through this function. Refresh / Clear: Click “Refresh” to get the latest information of system logs[...]

Chapter 3 Configuration 39 Security Logs Display the information of security logs. If hacker attacks your sever, h e will be isolated by the firewall function and the router will record related informa tion. Hence, you know where the hacker comes from. Refresh: Click “Refresh” to get the latest information of system logs. DHCP Table Display the[...]

Atlantis Land I-STORM ADSL ROUTER 40 3.4.9 Help/ Logout After click on the hyperlink of “Help” in the le ft pane, the following html page will ju mp out. This page would be a good reference as you precede the configuration. 3.5 Configuring with Web Browser in Bridge Mode Open the web browser, enter the local port IP address of this I-STOR M ADS[...]

Chapter 3 Configuration 41 At the configuration homepage, the left navi gation pane where bookmarks are provided links you directly to the desire d setup page, including LAN, WAN, System, Advanced, Status, Help . Click on the desired item to expand the page in the main navigation pane. 3.5.1 LAN This screen contains settings for L AN interface atta[...]

Atlantis Land I-STORM ADSL ROUTER 42 3.5.2 WAN The screen below contains settings fo r the WAN interface toward Internet. Protocol: There are two ways ─ RFC1483 and PPTP-to-PPPoA Relaying ─ for the device to have a public IP address. You have to check w ith your ISP about which way is adopted. VPI/VCI: Consult the telephone company to get the V[...]

Chapter 3 Configuration 43 3.5.3 System Password In factory setting, there is no pa ssword protection when user acce sses this ADSL Router. It is recommended that you change the default passw ord <BLANK> to ensure that som eone cannot adjust your settings without your permission. <BLANK> means there is no password. Every time you change[...]

Atlantis Land I-STORM ADSL ROUTER 44 Upgrade To upgrade the firmware of I-STORM AD SL ROUTER , you should download (from www.atlantisland.it ) or copy the firmware to your lo cal environment first. Press the “Brow se…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedure is complete[...]

Chapter 3 Configuration 45 Reboot In case the device stops responding correctly or in some other way stops functioning, you can perform the reboot. Your setting won’t be changed. Perform ing the reboot, click on the Reboot button. Each time you reboot your I-STORM ADSL ROUTER , the following figure will appear. Please wait 25 seconds for auto-rec[...]

Atlantis Land I-STORM ADSL ROUTER 46 Check “Enable” if you want to configure your I- STORM ADSL ROUTER from any PC in the Internet world with a web browser. To configure this device remotely, use the URL “http://LAN IP address” where LAN IP address is the IP address of the device ’s LAN port. You can find the value in the System Status. R[...]

Chapter 3 Configuration 47 Display the current LAN, WAN, and ADSL connecti on status. The first line under the WAN segment displays the WAN-ISP protocol you set. This page will refresh automatically every 15 seconds, which enables you to get the most updated status of your system. You can also click the “Refresh” button to get the latest inform[...]

Atlantis Land I-STORM ADSL ROUTER 48 Refresh / Clear: Click “Refresh” to get the latest information of system logs, or click “Clear” to eliminate all the system logs showed on this screen. 3.5.6 Help After click on the hyperlink of “Help” in the le ft pane, the following html page will ju mp out. This page would be a good reference as y[...]

Chapter 3 Configuration 49 Please note that the maximum input for password is 8 alphanum eric characters long. Since it is case sensitive , be sure that you remember whether a le tter is in upper or lower case and make sure that your Caps Lock is off. 3.7 Firmware Upgrade To upgrade the firmware of I-STORM ADSL ROUTER , you should download or copy [...]

50 Chapter 4 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for sim ple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then c onsult your service provider. Problems Starting Up the I-STORM ADSL ROUTER Problem Corrective A[...]

51 Problems Connecting to a Remote Node or ISP Problem Corrective Action Check section 3.4.8 “System Status” to verify the line status. Can’t connect to a remote node or ISP. In section 3.4.7 “Remote Config” , verify your login name and password for the remote node.[...]

52 APPENDIX A Specification Protocols IP, NAT, PPTP, ARP, ICMP, DHCP, PPPoE, PPPoA, IpoA, PPTP client, RIP1/2 LAN Port RJ-45, 1 ports 10/100Base-T WAN Port RJ-11, 1 ADSL port LED Indicators PPP, LAN-ACT, LAN-COL, ADSL, Power Input Power 5V DC @1.5A Power Consumption < 6 watts Agency and Regulatory FCC part 15 Class B, VCCI, CE Physical Dimension[...]

53 APPENDIX B Product Support If you have any problems with the ADSL Router, pl ease consult this m anual. Most problems can be resolved by using the Troubleshooting chapter. If you continue to have problems you should contact the dealer where you bought this ADSL Router. If you have any other questions you can contact the Atlantis Land company dir[...]