Audiovox MMD100 manuale d’uso

1 MMD100 10" DROP DOWN LCD MONIT OR & DVD PLA YER Owner/Inst allation Manual[...]

Import ant Notices Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or[...]

3 NOTE: This product incorporates copyright protection technology that is protected by method claims of certain patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation , and is intended for home and other limite[...]

4 A. Introduction Thank you for selecting the MMD100. The main features include a 10" Wide Screen (16:9 Aspect Ratio) Liquid Crystal Display (LCD) monitor and a built-in DVD player . The unit applies the latest state of the art electronics. The unit is constructed to provide years of reli- able, trouble-free service. Please read the entire ins[...]

5 5. Disc Do not use irregularly shaped discs such as heart or star-shaped discs as they may cause the unit to malfunction. Do not stick pa- per , tape or glue on the disc. Do not expose the disc to direct sun- light or heat sources such as hot air ducts. Do not touch the sur- face of disc. Handle the disc by its edge. Clean the disc by wiping the [...]

6 TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire S trippers Upholstery hook tool (for removal of panels as necessary) Electrical T ape Masking T ape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim rin[...]

7 5) Route the wiring harnesses throughout the vehicle as necessary . (Refer to the Wiring Diagrams on page 10 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when a[...]

8 Note: The MMD100 video system is only intended for an overhead, drop down installation. It is not intended for seat back or any other type of mounting. The hinging mechanism is designed for hori- zontal, drop down use only . VEHICLE PREP ARA TION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key[...]

9 Figure 1 MOUNTING THE MMD100 M4 8mm ¡ Á T rim Ring M4 8mm V ideo Unit T rim Ring Inst allation The T rim Ring Installation is accomplished using the four (4) 2.6X10mm screws supplied. Please refer to the Figure 2.[...]

10 1. Place the MMD100 on a soft surface with the rubber gasket facing up. Use care to avoid scratching the unit’s exterior sur- face. 2. T ake off the rubber ring. 3. Place the trim ring on the unit and note the location of the four mounting screws. 4. Attach the trim ring to the unit using the longer four (4) 2.6 X 10mm screws supplied. 5. Atta[...]

11 6. Attach the four (4) rubber spacers on the post extensions (Fig- ure 4). 7. Refer to the Owner/Install Manual for the MMD100 to complete the installation. Figure 3 Figure 4[...]

12 MMD100 1) Make the connections to the vehicle with the 5 pin wiring harness. 2) Connect the 5 pin harness to the mating connector on the Video Monitor . 3) Connect power harness to vehicle's electrical system by tapping into an accessory hot line. 4) V erify all functions of the system before final mounting of the finished assembly . NOTE: [...]

13 CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. T o [...]

14 Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto T o 3 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajar switch or Body Control computer Factory Dome light circuit Positive Switched Dome lighting Negative Switched Dome lighting T o 3 pin connector To constant To constant Factory Door ajar [...]

15 1) Headphone Jack 2) A V 2 In 3) SD Card Slot 4) Auto/Off/On Dome Light Switch 5) Power Button 6) Picture 7) V olume - 8) V olume + 9) FM Modulator Switch 10) Press Button 1 1) Dome Lights 12) IR Sensor and Infrared T ransmitter 13) S top Button 14) Reverse Scan Button 15) Forward Scan Button 16) Eject button 17) Play button 18) Disc Insertion S[...]

16 2. Remote Control V iew (Refer to Figure 9) 1) DVD /AUX Button 2) Power Button 3) Display Button 4) Angle Button 5) Subtitle Button 6) Repeat Button 7) A-B Button 8) Menu button 9) Slow Button 10) DVD/SD Button 1 1 ) Skip+ Button 12) Skip- Button 13) S top Button 14) Wide Button 15) Picture Button 16) V olume - 17) Zoom Button 18) Eject Button 1[...]

17 POWER PLA Y SLOW P AUSE STOP FORW ARD REVERSE UP/DOWN/LEFT /RIGHT ENTER NUMBERS RETURN MENU REPEA T A-B DISPLA Y ANGLE SUBTITLE AUDIO ZOOM SETUP DVD/AUX EJECT PICTURE VOLUME- VOLUME+ SKIP- SKIP+ DVD/SD T urn the unit on/off S tart Playback Play at 1/2,1/4,1/8, or 1/16 normal speed S till Picture (1 time) S top at the present playing point / (2 t[...]

18 H. Setup Press ‘SETUP’ to display the Main screen of the Setup Menu. Press ‘SETUP’ again to exit the Setup Menu and the unit will resume it’s last playback mode. 1) Press “SETUP”, the ‘General Setup Page’ will be displayed. a).Select ‘TV Display’ using the S / T button, and then press XX to enter the submenu. Select the TV [...]

19 b).Select ‘Angle Mark’ using the S / T button, and then press the XX button to enter the submenu. Choose Angle Mark on or of f using the S / T button and then press ENTER to confirm the setting. Press the WW button to return. Angle Mark Screen Display * On: The screen will show the angle mark icon. (*If an angle option is available). * Off: [...]

20 e). Select ‘Last Memory’ using the S / T button and then press the XX button to enter the submenu. Choose Last Memory on or off using the S / T button and then press ENTER to confirm the set- ting. Press the WW button to return. Last Memory Screen Display *On: The unit will return to the last position on the disc when power is cycled, but no[...]

21 2) Select “Video Quality Setup”by using the WW / XX button, press ENTER to enter the video quality setup page. Video Quality Setup Screen Display a) Select ‘Brightness’ by using the S / T button, then press ENTER. T o change the Brightness, press the WW / XX button. T o exit ‘Bright- ness’ setting, press ENTER again to return the mai[...]

22 b).Select ‘Contrast’ by using the S / T button, then press ENTER. T o adjust the Contrast, press the WW / XX button. Contrast Screen Display T o exit ‘Contrast’ Setting, press ENTER again to return the main Menu. c).Select ‘Saturation’ by using the S / T button, then press ENTER. T o adjust the Saturation, by press the WW / XX button[...]

23 3).Select “Password” using the WW / XX button, then press ENTER and press the XX button to enter the submenu. Password Setup Page Screen Display Press ENTER to enter the Password Change Page. Input the Old Password or the Default Password (Default 3308), followed by enter- ing the New Password, and the Confirmed New Password. Press ENTER to [...]

24 4 ) . With no disc inside the player select ‘Preference Page’ using the WW / XX buttons, then press ENTER to enter the Preference Page. a). Select ‘Audio’ using the S / T button, then press XX to enter the submenu. Select the audio language you desire using the S / T button, then press ENTER to confirm the setting. Press WW to return. Pr[...]

25 c). Select ‘Disc Menu’ using the S / T button, then press XX to enter the submenu. Select the Disc Menu Language you desire using the S / T button, then press ENTER to confirm the setting. Press WW to re- turn. Preference Menu Language d). Select ‘Parental’ using the S / T button, then press XX to enter the submenu. Parental Preference S[...]

26 e). Select ‘Default’ using the S / T button, then press XX to enter the submenu. Press ENTER to return all settings to the factory-set mode. NOTE: The parental setting and password are not affected by the default reset function and remain at their current values. Loading Factory Setting Lo ad F ac t or y S e t t i ng Re s e t D ef aul t[...]

27 I. Menu A DVD is divided into sections called titles and chapters. When you play a DVD, a root menu of the disc will appear on the screen of your TV or Monitor . The contents of the menu vary from disc to disc. Press MENU during playback to display the menu. Some DVDs only allow you to select disc playback options using the DVD root menu. J. Dis[...]

28 2. ANGLE During playback of a disc, press ‘ANGLE’ to display the available angles for discs containing multi-angles*, with the current angle number (1) and the total number of angles (2) displaying. Press ‘ANGLE’ to select another angle, then press again to exit and return to the normal view- ing angle. The angle information will disappe[...]

29 4. AUDIO During playback press ‘AUDIO’ to select the audio language you de- sire*, with the current Audio Channel Number (1) and the total number of Audio Channels (2) displayed. Press AUDIO again to select an- other audio language. The audio display will disappear automatically if the ‘AUDIO’ button is not pressed within for 3 seconds. [...]

30 6. A-B REPEA T a. During playback press ‘A-B’ to set the Starting Point A. A-B Repeat Starting Point Screen Display b. Press ‘A-B’ a second time to set the Ending Point B. The player will repeatedly play the part between Point A and Point B. A-B Repeat Ending Point Screen Display c. Press ‘A-B’ a third time to cancel A-B repeat and r[...]

31 7. REPEA T During playback each time REPEA T is pressed, the following modes will become available: Chapter: Repeat the current chapter T itle: Repeat the current title All: Repeat all chapters and titles Off: Resume normal playback The ‘Chapter ’ repeat display is shown below for example: Chapter Repeat Screen Display K. Playing Audio CDS W[...]

32 T otal Elapsed: The current track playing and the total time that the CD has been playing. T otal Remain: The current track playing and the amount of time remai ning on th e CD. Display Off: The CD time Information will not be displayed. T ake ‘Single Elapsed’ display as a example: Single Elapsed Screen Display USING THE REPEA T FEA TURE The[...]

33 L. Playing MP3 Discs MP3 is a format for storing digital audio. An audio CD-quality song is compressed into the MP3 format with very little loss of audio quality while taking up much less disc space. CD-R /RW discs that have been encoded in MP3 format are compatible with this system. MP3 MENU Screen Display When an MP3 disc is inserted into the [...]

34 4. Use the ( NEXT ) button to move to the next song. Press the (PREVIOUS) button to move to the beginning of the previous song. USING THE REPEA T FEA TURE The default mode for the Repeat feature is OFF . Pressing REPEA T consecutively changes the repeat options: • Repeat One (repeat playback of a song) • Repeat Folder (repeat playback of a s[...]

35 M. Playing a Video Game (Refer to Figures 10 and 1 1.) Change the source by pressing the DVD/AUX button on the re- mote. The AV1 input is the RCA connectors located on the top of the unit. The AV2* input jack is located on the left side of the unit. Figure 10 Figure 11 Connect the A/V output from your game system to the RCA inputs (AV1) or the 1[...]

36 O.Wireless FM Modulator The MMD100 is equipped with built-in wireless FM Modulator*, that al- lows you to listen to the MMD100 audio signal by tuning your vehicle’s radio to the selected frequency (88.1, 88.3, 88.5, 88.7 or 88.9 MHz). First, Press the FM button on the player , The “FM ** MHz” will appear on the screen. Then use the FM butt[...]

37 Q. T roubleshooting: No power at Video Monitor Power but no video or sound Picture, but no sound REMEDY : -V erify +12 VDC on the Red wire at 2 pin Power Harness behind video monitor . V erify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness. -V erify that the correct source is selected (i.e.: DV[...]

128-8287 © 2007 Audiovox Electronics Corporation, 150 Marcus Blvd., Haupp auge, New Y ork 1 1788 AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the d[...]