Audiovox PRO-9675FT manuale d’uso

4 Channel Remote Car Starter With Full Feature Alarm System Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only . Kit Contents: Remote Start/Alarm Control Module (2) - Three Button Anti Code Gra[...]

The PRO-9675 Remote S tart/Alarm System is designed to be used with Automatic T ransmission V ehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug pre-h[...]

chosen location to insure that the drill will not penetrate any existing factory wiring or fluid lines. Carefully drill a 1/4" hole in the desired location and pass the connector end of the LED through the hole and toward the control module. Press the LED firmly into place until it is fully seated in the mounting hole. THE RECEIVER/ANTENNA ASS[...]

The PRO-9675 is to be used in vehicles with AUTOMA TIC TRANSMISSIONS only! Although this combination Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and property damage. IMPORT ANT! DO NOT PLUG[...]

BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY&quo[...]

WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red T race Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay . If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) NOTE: If the vehicle&apo[...]

Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and some Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In most cases, the Purple wire will need to be connected to only one door switch no matter how m[...]

General Motors V A TS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below , a relay will be [...]

Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay , and wired to the vehicles interior[...]

Orange Wire: Ground When Armed Output This wire provides a 300mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ignition switch [...]

Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange T race Wire: T achometer Input Signal This wire will conti[...]

Dark Blue Wire: Delayed 300mA Pulsed Channel 2 Output The Dark Blue wire supplies a 300mA ground pulsed output whenever channel two of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must be connected to a relay to supply power to the trunk release [...]

T ypically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the ignition circuit transitions to off. Black w/ Y ellow T race Wire: Ground Output During S tart (Crank) The Black w/ Y ellow T race wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This outp[...]

3 Wire Positive Switched Door Lock/Unlock Wiring Detail 14 3 Wire Ground Switched Door Lock/Unlock Wiring Detail 128-5371 14 of 22 T o Red Lock Wire Of Control Module T o Green Unlock Wire Of Control Module 3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness provide sa+1 2 volt pulse during the disarming se[...]

LED Flash Pattern 1 Flash Pause etc. 2 Flash Pause etc. 3 Flash Pause etc. 4 Flash Pause etc. 5 Flash Pause etc. First Second Third Fourth Fifth Action Turn the ignition switch on Flip the valet/program switch on then off 3 times Within 3 seconds, turn the ignition switch off and then on. Press the transmitter's Arm/Disarm to toggle between th[...]

REMOTE ST ART SELECT ABLE FEA TURES RF Programmable Features: LED Pattern 1 x Pause etc. 2 x Pause etc. 3 x Pause etc. 4 x Pause etc. 5 x Pause etc. 6 x Pause etc. 7 x Pause etc. 8 x Pause etc. 9 x Pause etc. 10 x Pause etc. Default Off 10 Minutes Steady T ach ---------------- Off during crank Off --------------- Gasoline Pole 5X Park Lights Flashe[...]

17 128-5371 17 of 22 3. Flip the valet/program switch On, Off, On, Off, On, then Off. Siren will chirp once. 4. Immediately turn the ignition key Off. One long siren chirp. 5. Flip the valet/program switch On, then start the vehicle using the key . 6. When the unit senses the tach signal, the parking lights will begin to flash. 7. Flip the valet/pr[...]

TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOOD PIN SAFETY SHUT DOW[...]

MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanical function will n[...]

KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from starting in gear . AUDI[...]

METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C . Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D .[...]

WIRING DIAGRAM Form No. 128-5371 © 1998 Audiovox Corporation, 150 Marcus Blvd.., Hauppauge, N.Y . 1 1788 128-5371 22 of 22[...]