Autostart AS-1535 SH manuale d’uso

Notice The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itse lf or to the Unit. This Unit must be installed by a certified technician using all safety devices supplied. Please note that this guide has been written for properly trained A[...]

P.2 Installation Guide AS-1535 SH Table of Contents Introduction ..................................................... 3 Included in the Package ................................. 3 Before You Get Started … ............................... 3 Harness Description ....................................... 4 6-Pin Main Ignition Harness ..................[...]

AS-1535 SH Installation Guide P.3 Introduction This Guidebook conta ins all informa tion pertinent to t he installation. Most (if not al l) features are grouped in t he User Guidebook and th erefore, should you need infor mation on a featur e, you should refer to the User Guidebook Included in the Package Before beginning the installation, p lease [...]

P.4 Installation Guide AS-1535 SH Ƈ Never leave the keys in the car. Leave them on a workbench with a window rolled down. Ƈ Remove courtesy light fuse, if possible, to prevent battery drain. Ƈ The Programming Assistance Button (A.k.a. PAB.) The PAB is mounted on the side of the Unit. This push butto n mimics the Hood-Pin switch in order to avoid[...]

AS-1535 SH Installation Guide P.5 6-Pin Main Ignition Harness Wire Description A RED +12 V Battery Connect to the largest 12 V supply wire at the Ignition harness. Ensure that the OEM power wire is fused for mor e than 30 A. NOTE: certain new vehicles have no su itabl e 12 volts source at the IGNITION switch (the 12 Volt wire is too sm all to suppl[...]

P.6 Installation Guide AS-1535 SH NOTE: A Tach signal that is too low will cause the Module to “ over crank” and a Tach signal tha t is too high will caus e the Module to “under crank”. 3 GREY (-) Hood Switch input Connect this wire to t he Hood Pin-switch s upp lied. This input will disable or shut down the Remote Starter when the Hood is [...]

AS-1535 SH Installation Guide P.7 7 WHITE / ORANGE (–) Starter Kill output The unit is equipped wit h a selectable passi ve- or active-arming Starter Kill circuit that will immobilize the vehicle when the system is armed. This wire will provide a constant 500-mA negative out put when the system is armed (locked by remote) or if remote started. Th[...]

P.8 Installation Guide AS-1535 SH 9 (cont.) PURPLE (-) External Trigger Option 3 (Key Sense (-) Input): Connects to OEM Key Sense Wire. When the Key is detected in the Ignition Switch (Ground (-) signal on the OEM Key Sense Wire) the Starter Kill will not ARM even when it is set to Passive Mode. If Secure Lock is programmed, LOCK and ARM will not b[...]

AS-1535 SH Installation Guide P.9 12 (cont.) YELLOW (+) Glow- plug Light input (cont.) A diode must be added betwee n the negative Glow-plug trigger on the relay and the negative Glow-plu g wire of the car. This is to prevent feedback effects on the Glow-plug indicator light on the instru ment cluster: the light on th e dash would come on b ecause [...]

The Installer … The Module … 1- Press and hold the Hood pin for 4 s econds. 2- Let go of the Hood Pin. Parking Lights “ON” 3- While the Parking Lights are on, press down the Hood Pin once more. 4- Release the Hood Pin a gain --be careful not to over flash the Hood Pin as this will bri ng up the Events Playback and will not bring you th e Pr[...]

AS-1535 SH Installation Guide P.11 The Module has t he ability to retain up to 4 different Transmitter codes; if a fifth Transmitter is programmed, the code of th e first Transmitter will be erased from memory. To erase all Transmitter codes from memory, you mu st perform a Module reset (See “Resetting the Module” on page 17 ). To program the T[...]

P.12 Installation Guide AS-1535 SH Options Programming MODE 1 *indicates default setting FUNCTION 1 – Ignition-controlled Door Locks OPTION 1* Ignition Locks ENABLED OPTION 2 Ignition Locks DISABLED OPTION 3 Ignition LOCK only OPTION 4 Ignition UNLOCK only FUNCTION 2 – Secure Lock OPTION 1* Secure Lock DISABLED (1-second Disarm pulse) OPTION 2 [...]

AS-1535 SH Installation Guide P.13 OPTION 2* Disabled OPTION 3 Disabled MODE 3 *indicates default setting FUNCTION 1 – Home Valet Mode OPTION 1 Home Valet ENABLED OPTION 2* Home Valet DISABLED OPTION 3 Home Valet DISABLED FUNCTION 2 – AUX 3 / Zone 3 output OPTION 1 Trunk output when TRUNK button pressed for 3-sec while Ignition is OFF OPTION 2*[...]

P.14 Installation Guide AS-1535 SH Close the Hood to cancel th e changes. Table 4 Auto Tach Programming Pr ocedure This process can be carried out inst ead of the co nvention al Tach Programming Pr ocedure. 1. Make sure all the connections are done properly an d that the Module has b een powered-up. 2. With the Hood up (Ground on the Hood Pi n line[...]

AS-1535 SH Installation Guide P.15 2. Test Hood Switch shutdown : with the vehicle running un der the Remote Starter, open the Hood; the vehicl e should s hut down. If it does not sh ut down, check the Hood Pin-switch and its connector. 3. Test the Brake shutdown circuit : With the vehicle running u nder the Remote Starter, press and release the Br[...]

Caution! Do not use mor e than one of t he three sets of jumper pins simultaneously. The relay output rating on this Un it is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, caus ing the 30A fuse to blow. Using a digital voltm eter, check the Starter wire for amperage when vehicle is crank ing. Ignition-Controlle[...]

AS-1535 SH Installation Guide P.17 Turbo Mode This Option allows turboch argers to idle down: after the user le aves the vehicle, the E ngine will keep running for 6 0 sec. and then shut down (It is a 1-minute Idle Mod e). Safe Start (Child Safety Mode) ( OFF by default.) Requires the user presses the S TART button on the Tr ansmitter twice within [...]

P.18 Installation Guide AS-1535 SH x With the Parking Lights o n, immediat ely push the Pin-switch 3 times. x The Parking Lights and L.E.D. will flash the five events stored in memory. Table 12 The first four playback codes are S tart Failure Events . There is a p ause after each event code is played back. The system will play back the most recent [...]

AS-1535 SH Installation Guide P.19 Note: “x” stands for one flash of the Parking Lights Diagnostics - Parking Lights Flash Rate Flashes Description 1 x Doors locked, Starter Kill ar med. x End of Run Time. x TRUNK button pressed x START signal received by the Module . x Cold Weather Mode cance lled. x Cannot start after maximum number of attemp[...]