Avaya C460 manuale d’uso

Avaya Reference Guide A VAYA C460 M ULTILAYER M ODULAR S WITCH S OFTWARE V ERSION 2.0 May 2003[...]

avaya.com © 2003 Avaya Inc. All rights re served. All trademarks id entified by the ® or TM are registered trademarks or trademarks, r espectively, of Avaya Inc. All other trademarks are t h e property of their respective owners Document no. 555-500 -200[...]

Avaya C460 Reference Guide i Contents Chapter 1 Using the CLI ............ ....................... ...................... .......................... ...................... ........ 1 CLI Architecture ............ ....................... ......................... ....................... ................. 1 Conventions Used ..................... ....[...]

Contents ii Avaya C460 Reference Guide clear fragment ....... ....................... ...................... ....................... .................. 18 clear interface ...................... ....................... ...................... .......................... . 19 clear ip route ..................... ....................... ................[...]

Contents Avaya C460 Reference Guide iii ip access-list-dscp name .......... .......................... ...................... .................. 40 ip access-list-dscp operation ............ ......................... ....................... ......... 40 ip access-list-dscp preced ence ........... ....................... ......................... ..[...]

Contents iv Avaya C460 Reference Guide ip vrrp primary ................ .......................... ...................... ....................... .... 64 ip vrrp priority ............... ......................... ....................... ...................... ....... 65 ip vrrp timer .......... ....................... ...................... .......[...]

Contents Avaya C460 Reference Guide v set inband vlan .................... .......................... ...................... ....................... . 88 set intelligent-multicast ........... .......................... ......................... ............... 88 set intelligent-multicast client port pruning time ........ ......................... [...]

Contents vi Avaya C460 Reference Guide set port redundancy on/off ............... .......................... ...................... ..... 115 set port redundancy-intervals ...... .......................... ...................... ........... 115 set port spantree .......... ...................... ....................... ...................... ......[...]

Contents Avaya C460 Reference Guide vii set timezone .......... ....................... ......................... ....................... ............. 137 set trunk ......... ...................... .......................... ...................... ...................... 138 set vlan ................... ....................... .....................[...]

Contents viii Avaya C460 Reference Guide show ip ospf ................... ......................... ....................... ...................... ..... 160 show ip ospf database ................. ...................... ....................... ................ 161 show ip ospf interface .............. ......................... .....................[...]

Contents Avaya C460 Reference Guide ix show ppp configuration .... ............................. ...................... ............ ....... 201 show ppp incoming timeout ............. ........................................... .......... 201 show ppp session .... ......................................................... .............. .......... [...]

Contents x Avaya C460 Reference Guide Layer 2 CLI Commands ....................... ....................... ...................... ........................ 233 Layer 3 CLI Commands ....................... ....................... ...................... ........................ 237 Glossary.............. ......................... .....................[...]

Avaya C460 Reference Guide 1 Chapter 1 Using the CLI This chapter describes the Avaya C460 CLI architecture and conventions, an d provides instructions for accessing the Avaya C460 for configurat ion purposes. The configuration procedure involves establishing a Telnet session or a serial connection and then using the Avaya C4 60’s internal CLI. F[...]

Chapter 1 Using the CL I 2 Avaya C460 Reference Guide Conventions Used • Mandatory keywords ar e in the computer bold font. • Information displayed on s creen is displayed in computer font. • Variables that you supply are in pointed brackets <>. • Optional keywords are in square brackets []. • Alternative but mandatory keyword s are[...]

Chapter 1 Using the CLI Avaya C460 Reference Guide 3 The command line prompt looks as follows: London-1(configure router:ospf)# The command prompt is not hierarchical in structure. If you wish to use several c o m m a n d s , e a c h b e g i n n i n g w i t h t h e sa me k e y w o r d , y o u m u s t r e t y p e a l l p a r t s o f t h e command ea[...]

Chapter 1 Using the CL I 4 Avaya C460 Reference Guide Navigation, Cursor Movement and Shortcu ts The CLI contains a simple text editor with these functions: Command Syntax Commands are not case-sensitive. That is , uppercase and lowercase char acters may be interchanged freely. Command Abbreviations All commands and parameters in the CLI can be tru[...]

Chapter 1 Using the CLI Avaya C460 Reference Guide 5 Universal Commands Universal commands are commands that can be issued anywhere in the hierarchical tree. Retstatus command Use the retstatus command to show whether the last CLI command you performed was successful . It displays the return status of the previous c ommand. The syntax for this comm[...]

Chapter 1 Using the CL I 6 Avaya C460 Reference Guide terminal width Use the terminal width command to set the terminal width of the terminal display. The syntax for this command is: terminal width [<character>] Example: terminal length Use the terminal length command to set the length of the terminal display. The syntax for this command is: [...]

Chapter 1 Using the CLI Avaya C460 Reference Guide 7 clear screen Use the clear screen command to clear the current te rminal display. The syntax for this command is: clear screen Example: C460-1> clear screen Welcome to C460 SW version 1.0.0 C460-1>[...]

Chapter 1 Using the CL I 8 Avaya C460 Reference Guide Avaya C460 Sessions You can use sessi ons to switch between C460 Supervisor modules or to switch between Layer 2 and Layer 3 commands in the C460 CLI. To switch between C460 modules use the command: session [<mod_num>] <mode> . The < mod_num > is the number of the module in the[...]

Chapter 1 Using the CLI Avaya C460 Reference Guide 9 Security Levels There are four security access levels (modes) – User, Privileged, Configure and Supervisor. • The User mode is a general access level used to show system parameter values. • The Privileged mode is used by site personnel to access sw itch configuration options. • The Config[...]

Chapter 1 Using the CL I 10 Avaya C460 Reference Guide Entering the CLI To enter the CLI, enter your username and password. Your acces s level is indicated in the prompt as follows: The User level prompt is shown below: C460-1> The Privileged level prompt is shown below: C460-1# The Configure level pr ompt for Laye r 3 configuration is shown bel[...]

Chapter 1 Using the CLI Avaya C460 Reference Guide 11 Router Configuration Contexts You can either use the general C460 commands available from the Router(configure)# prompt or you can enter one of two router configuration context modes: • Router i nterface c ontext: This allows you to define parameters individually for each interface. To enter t[...]

Chapter 1 Using the CL I 12 Avaya C460 Reference Guide[...]

Avaya C460 Reference Guide 13 Chapter 2 Avaya C460 CLI Commands This chapter describes all the C460 CLI commands and parameters in alphabetica l order. access list See “ip access-list” area User level: read-write, admin. L You can only access this command in Router-OSPF mode. Type router ospf at the command prompt to enter Router -OSPF mode if [...]

Chapter 2 Avaya C460 CLI Commands 14 Avaya C460 Reference Guide arp User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the arp command to a dd a permanent entry to the Address Resolution Protocol (ARP) c[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 15 The syntax for this command is: [no] arp timeout <seconds> Example: To set the arp timeout to one hour: To restore the def ault arp timeout: banner logi n Use the banner login command to enter the login banner configuration mode. Use the no banner login command to set the login b[...]

Chapter 2 Avaya C460 CLI Commands 16 Avaya C460 Reference Guide The syntax for this command is: [no] banner post-login Example: banner post-login lin e See “line” clear arp-cache User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command promp[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 17 clear cam User level: read-write, admin. Use the clear cam command to delete all entries from the CAM table. The syntax for this command is: clear cam Example: clear dot1x config User level: privileged, supervisor. Use the clear dot1x config command to disable dot1x on all ports and re[...]

Chapter 2 Avaya C460 CLI Commands 18 Avaya C460 Reference Guide Example: clear even t-log User level: read-write, admin. Use the clear event-log command to delete the log file of a Supervis or module. The syntax for this command is: clear event-log [<module_number>] Example: clear fragmen t User level: read-write, admin. Use the clear fragmen[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 19 clear interface User level: read-write, admin. Use the clear interface command to clear the inband or outband interface from the NVRAM. The syntax for this command is: clear interface [outband | inband] Example: clear ip route User level: read-write, admin. Use the clear ip route comma[...]

Chapter 2 Avaya C460 CLI Commands 20 Avaya C460 Reference Guide Use the clear ip route command to delete all the dynamic r outing entries from the Routing Tabl e. The syntax for this command is: clear ip route * | <ip-addr> [<ip-mask>] Example: clear ip tr affic User level: read-write, admin. Use the clear ip traffic co m mand to clear [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 21 Example: clear port static-vl an User level: read-write, admin. Use the clear port static-vlan command to delete VLANs statical ly configured on a port. The syntax for this command is: clear port static-vlan [module/port range][vlan num] Example: clear radius authen tication server Use[...]

Chapter 2 Avaya C460 CLI Commands 22 Avaya C460 Reference Guide Example: clear rmon2 stat istics User level: read-write, admin. Use the clear rmon2 statistics command to delete rmon2 (AnyLayer SMON) statistics. The syntax for this command is: clear rmon2 statistics Example: clear screen User level: read-only, read-write, admin. Use the clear screen[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 23 Example: clear system-log User level: read-write, admin. Use the clear system-log command to delete the log f ile of a Supervisor Module. The syntax for this command is: clear system-log [<module_number>] Example: clear timezone User level: read-write, admin. Use the clear timezo[...]

Chapter 2 Avaya C460 CLI Commands 24 Avaya C460 Reference Guide clear vlan User level: read-write, admin. Use the clear vlan command to dele te an existing VLAN and return ports from this VLAN to the default VLAN #1. When you clear a VLAN, all ports assigned to that VLAN are assigned to the default VLAN #1. The syntax for this command is: clear vla[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 25 If you wish to define a name which includes spaces , you must enclose the entire name in quotation marks, for example “new york”. configure User level: read-write, admin. Use the configure command to enter configure mode. The syntax for this command is: configure Example: copy l2-c[...]

Chapter 2 Avaya C460 CLI Commands 26 Avaya C460 Reference Guide The syntax for this command is: copy running-config startup-config Example: 1 copy running-config tftp User level: privileged, supervisor. Use the copy running-config tftp command to upload the policy configuration to a TFTP server. The syntax for this command is: copy running-config t[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 27 Example (for Windows): Example: (for Unix): copy tftp EW_archive User level: read-write, admin. Use the copy tftp EW-archive command to download the C460 Manager application into the switch via TFTP. L To use this command, you need to have an active TFTP server and to create a file int[...]

Chapter 2 Avaya C460 CLI Commands 28 Avaya C460 Reference Guide The syntax for this command is: copy tftp l2-config <filename> <ip> Example: copy tftp startup-config User level: read-write, admin. Use the copy tftp startup-config command to copy the C460 configuration from the saved TFTP file to the Startup Configuration NVRAM. The synt[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 29 additional TFTP server. copy tftp SW_imageA <filename> <ip> Example: copy tftp SW_image B User level: read-write, admin. Use the copy tftp SW_imageB command to updates the software image in Bank B of all the Supervisor Modules installed in the switch. To use this command, y[...]

Chapter 2 Avaya C460 CLI Commands 30 Avaya C460 Reference Guide default-metri c User level: read-write, admin. L You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary. Use the default metric command to set the interface RIP route met ric. Use the no default metric comman[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 31 default-metric (R IP) User level: read-write, admin. L You can only access this command in the RIP context Type router rip at the command prompt to enter interface mode if necessary. Use the default metric command to set the interface RIP route metric. Use the no default metric command[...]

Chapter 2 Avaya C460 CLI Commands 32 Avaya C460 Reference Guide enable interfa ce User level: read-write, admin. Use the enable interface command to enable the inband and outband interfaces. The syntax for this command is: en[able] interface {outband | inband} Example: enable vlan com mands User level: read-write, admin. L You can only access this [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 33 erase startup-config User level: read-write, admin. Use the erase startup-config command to clear the startup config uration. The syntax for this command is: erase startup-config Example: fragment chain Use the fragment chain command to set the maximum number of fragments that can comp[...]

Chapter 2 Avaya C460 CLI Commands 34 Avaya C460 Reference Guide Example: fragment timeout Use the fragment timeout command to set the maximum number of seconds to reassemble a fragmented IP packet destined to the router. Use the no form of this command to set the fragment timeout to the default value (10). L The router does not perform reas sembly [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 35 The syntax for this command is: [no] hostname [<hostname_string>] Example: If you wish to enter a n a me which includ es spaces, you must enclose the entire name in quotation marks, for example “new york”. hostname (Layer 3) User level: read-write, admin. Changes the system p[...]

Chapter 2 Avaya C460 CLI Commands 36 Avaya C460 Reference Guide interf ace User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the interface command to create and enter the Interface Configuration Mode. U[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 37 ip access-defa ult-action User level: read-write, admin. L If you are at the ”read-write” user level, you can only access this command in Configure mode. Type configure at th e c o mm a n d pr o m p t t o e n te r c on f i g ur e m o d e i f n ec e s sa r y . Use the ip access-defa[...]

Chapter 2 Avaya C460 CLI Commands 38 Avaya C460 Reference Guide ip access -lis t User level: read-write, admin. L If you are at the ”read-write” user level, you can only access this command in Configure mode. Type configure a t t he c o mm a n d p ro m p t to e n te r c o nf i g u re m o d e i f n e ce s s ar y . Use the ip access list command [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 39 Example: ip access-list-cookie User level: read-write, admin. L If you are at the ”read-write” user level, you can only access this command in Configure mode. Type configure at th e c o mm a n d pr o m p t t o e n te r c on f i g ur e m o d e i f n ec e s sa r y . Use the ip access[...]

Chapter 2 Avaya C460 CLI Commands 40 Avaya C460 Reference Guide Example: ip access-l ist-dscp name User level: read-write, admin. L If you are at the ”read-write” user level, you can only access this command in Configure mode. Type configure a t t he c o mm a n d p ro m p t to e n te r c o nf i g u re m o d e i f n e ce s s ar y . Use the i p a[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 41 <action> Example: ip access-list-dscp prece dence User level: read-write, admin. L If you are at the ”read-write” user level, you can only access this command in Configure mode. Type configure at th e c o mm a n d pr o m p t t o e n te r c on f i g ur e m o d e i f n ec e s s[...]

Chapter 2 Avaya C460 CLI Commands 42 Avaya C460 Reference Guide Example: ip access-list-d scp trust User level: read-write, admin. Use the ip access-list-dscp trust command to decide which original frame fields influence the sele ction of packet priority. The syntax for this comman d is: ip access-list-dscp trust <policy-list-number> {untrust[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 43 Example: If you wish to define a name which includes spaces , you must enclose the entire name in quotation marks, for example “new york”. ip access-list-owner User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Config[...]

Chapter 2 Avaya C460 CLI Commands 44 Avaya C460 Reference Guide Example: To assign the IP address 192.168.22.33 wi th mask 255 .255.255.0 to the interface “marketing”: ip admin-state User level: read-write, admin. L You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode. Use the a[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 45 The syntax for this command is: [no] ip bootp-dhcp network <ip-address> Example: To select the network 192.168.169.0 as the network from which an addres s shall be allocated for bootp/dhcp reques ts: ip bootp-dhcp relay User level: read-write, admin. L If you are at the “read-w[...]

Chapter 2 Avaya C460 CLI Commands 46 Avaya C460 Reference Guide ip bootp-dhcp server User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip bootp-dhcp server command to add a bootp/dhcp server to handle bootp/dhcp requests rece[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 47 ip default-gate way User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the ip default-gateway command to define a default gateway (router).[...]

Chapter 2 Avaya C460 CLI Commands 48 Avaya C460 Reference Guide ip icmp-err ors User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the icmp-error command to turn ICMP error me ssages on. Use the no icmp-[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 49 To restore the maximum number of ARP cache entries to its default: ip max-route-entries User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. The [...]

Chapter 2 Avaya C460 CLI Commands 50 Avaya C460 Reference Guide The possible values of mode are: Example: To enable rebroadcasting of netbios packet s received by and sent from the interface “marketing”: ip netmask-format User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configur[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 51 Example: To display netmas ks in decimal format: ip ospf authentic ation-key User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf authentication-key command[...]

Chapter 2 Avaya C460 CLI Commands 52 Avaya C460 Reference Guide Example: ip ospf dead-in terval User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf dead-interval command to configure the interval before declaring the ne[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 53 Example: ip ospf priority User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip ospf priority command to configure interface priority used in DR election. Use the[...]

Chapter 2 Avaya C460 CLI Commands 54 Avaya C460 Reference Guide Example: ip proxy-arp User level: read-write, admin. L You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode. Use the ip proxy-arp command to enables proxy ARP on an interface. Use the no ip proxy-arp command to disable [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 55 Type interface [name] at the command prompt to enter interface mode if necessary. Use the ip rip authentication key command to set the authentication string used on the interface. Use the no ip rip authentication key command to clear the password. The syntax for this command is: [no] i[...]

Chapter 2 Avaya C460 CLI Commands 56 Avaya C460 Reference Guide “marketing”. ip rip default-rout e-mode User level: read-write, admin. L You can only access this command in interface mode. Type interface [name] at the command prompt to enter interface mode if necessary. Use the ip rip default-route-mode command to enable learning of the default[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 57 loops. Poison reverse updates explicitly indicate that a network or subnet is unreachable rather than implying they are not reachable. Poison reverse updates are sent to defeat larg e routi ng loops. The syntax for this command is: [no] ip rip poison-reverse Example: ip rip rip-version[...]

Chapter 2 Avaya C460 CLI Commands 58 Avaya C460 Reference Guide necessary. Use the ip rip send-receive command to set the RIP Send and Receive mode on an interface. The default state is talk-listen . The syntax for this command is: ip rip send-receive-mode <mode>[<default route metric>] Example: To set the RIP Send and Receive mode on t[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 59 Example: ip route User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the ip route command to establish a static route. Use the no ip route [...]

Chapter 2 Avaya C460 CLI Commands 60 Avaya C460 Reference Guide Use the ip routing command to enable IP routing. Use the no ip routing command to disable the IP routing process in the device. By default, IP rou ting is enabled. The syntax for this command is: [no] ip routing Example: ip routing-mode User level: read-write, admin. L You can only acc[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 61 ip simulate User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the ip simulate command to check the policy for a simulated packet. The comm[...]

Chapter 2 Avaya C460 CLI Commands 62 Avaya C460 Reference Guide default VLAN. The syntax for this command is: [no] ip vlan <vlan-id> Example: To specify VLAN development al as the VLAN used by interface “products”: If you wish to define a name which incl udes spaces, you must enclose the entire name in quotation marks, for example “new [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 63 The syntax for this command is: [no] ip vrrp <vr-id> address <ip-address> Example: To assign add ress 10.0.1 .2 to virtua l router 1: ip vrrp auth-ke y User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command [...]

Chapter 2 Avaya C460 CLI Commands 64 Avaya C460 Reference Guide The syntax for this command is: [no] ip vrrp <vr-id> override addr owner Example: ip vrrp preempt User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip vrrp[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 65 for the virtual router instance. By default, the pr imary address is se lected automatically by the device. The syntax for this command is: [no] ip vrrp <vr-id> primary <ip-address> Example: ip vrrp prio rity User level: read-write, admin. L You can only access this command[...]

Chapter 2 Avaya C460 CLI Commands 66 Avaya C460 Reference Guide To set the virtual router simple password for virtual router 1 to abcd: ip vrrp timer User level: read-write, admin. L You can only access this command in Interface mode. Type interface [name] at the command prompt to enter Interface mode if necessary. Use the ip vrrp timer command to [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 67 Example: network (RIP) User level: read-write, admin. L You can only access this co mm and in router-RIP mode. Type router rip at the command prompt to enter router-RIP m ode if necessary. Use the network command to specify a list of networks on which the RIP is running. Use the no net[...]

Chapter 2 Avaya C460 CLI Commands 68 Avaya C460 Reference Guide The syntax for this command is: network <net addr> [<wildcard-mask> [area <area id>]] Example: no rmon alarm User level: read-write, admin. Use the no rmon history command to delete an existing RMON alarm entry. The syntax for this command is: no rmon alarm <Alarm [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 69 no rmon history User level: read-write, admin. Use the no rmon history command to delete an existing RMON history entry. The syntax for this command is: no rmon history <History Index> Example: no username User level: admin. Use the no username command to remove a local user acco[...]

Chapter 2 Avaya C460 CLI Commands 70 Avaya C460 Reference Guide nvram initialize {switch | all} Example: L The nvram initialize command does not al ter the Active/Standby status of the Supervisor modules. passive-int erface User level: read-write, admin. L You can only access this command in Router-OSPF mode. Type router ospf at the command prompt [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 71 ping User level: read-only, read-write, admin. Use the ping command to send ICMP echo request packets to another node on the network. The syntax for this command is: ping [host] Example: to ping the IP number 149.49.48.1: ping (Layer 3) User level: user, privileged, supervisor Use the [...]

Chapter 2 Avaya C460 CLI Commands 72 Avaya C460 Reference Guide Example: to ping the IP nu mber 149.49.48.1 three times: redistribute (OSPF) User level: read-write, admin. L You can only access this command in Router-OSPF mode. Type router ospf at the command prompt to enter Router -OSPF mode if necessary. Use the red istribute command to redistrib[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 73 The default is disabled. The syntax for this command is: [no] redistribute <protocol> Example: reset User level: read-only, read-write, admin. Use the reset c omm an d t o re sta rt t he sys te m or an ind iv idu al S up erv iso r m odu le . The syntax for this command is: reset [...]

Chapter 2 Avaya C460 CLI Commands 74 Avaya C460 Reference Guide C460-1(super)# reset chassis This command will reset the chassis *** Reset *** - do you want to continue (Y/N)? y Reseting chassis... C460-1(super)# Avaya C460 Boot Creation date: Jan 6 2003, 18:29:57 Press any key to stop auto-boot... 0 auto-booting... Bank B is OK. SW runs from bank [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 75 rmon alarm User level: read-write, admin. Use the rmon alarm command to create a new RMON alarm entry. The syntax for this command is: rmon alarm <Alarm Number> <variable> <interval> <sampletype> rising-threshold <rising threshold> <rising event> fal[...]

Chapter 2 Avaya C460 CLI Commands 76 Avaya C460 Reference Guide rmon event User level: read-write, admin. Use the rmon event command to create an RMON event entry. The syntax for this command is: rmon event <Event Number> <type> description <description> owner <owner> Example: rmon history User level: read-write, admin. Use [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 77 Example: If you wish to define a name which includes spaces , you must enclose the entire name in quotation marks, for example “new york”. rmon2 protocol-dir User level: privileged, supervisor. L If you are at the ”privileg ed” level, you can only access this command in Configu[...]

Chapter 2 Avaya C460 CLI Commands 78 Avaya C460 Reference Guide application. Use the no rmon2 protocol-dist command to disable the applicat ion. The syntax for this command is: [no] rmon2 protocol-dist Example: router ospf User level: read-write, admin. Use the router ospf command to enable the OSPF protocol on the system. Use the no router ospf co[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 79 To enable the RIP protocol: router vrrp User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the command to enable VRRP routing globally. Use[...]

Chapter 2 Avaya C460 CLI Commands 80 Avaya C460 Reference Guide Example: L The security level stays the same when you us e the session command. set allowed mana gers User level: read-write, admin. Use the set allowed managers command to enables or disable the Allow ed Managers featu re. When this feature is enabled , only those st ations whose IP a[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 81 Example: set arp-aging-inter val User level: read-write, admin. Use the set arp-aging interval command to set the ARP table aging inter v al for gateways’ entries in the agent ARP table. The MAC value for the default gateway of th e agent in the ARP table, is deleted at the end of ev[...]

Chapter 2 Avaya C460 CLI Commands 82 Avaya C460 Reference Guide Example: set boot bank User level: read-write, admin. Use the set boot bank command to set the system boot bank (for the active Supervisor Module). The syntax for this command is: set boot bank <value> Example: set broadcast storm control User level: read-write, admin. Use the se[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 83 set broadcast storm control threshold User level: read-write, admin. Use the set broadcast storm control threshold command to set the broadcast storm control threshold. The syntax for this command is: set broadcast storm control threshold <threshold> Example: set device-mode User[...]

Chapter 2 Avaya C460 CLI Commands 84 Avaya C460 Reference Guide set device-mode (Layer 3) User level: read-write, admin. Use the set device-mode command to change the basi c mode of operation of the C460 switch between Router and Layer 2 modes . The syntax for this command is: set device-mode <mode> Example: set dot1x max-req User level: supe[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 85 Example: set dot1x re-authperiod User level: supervisor Use the set dot1x re-authperiod command to set the idle time between re- authentication attempts. The syntax for this command is: set dot1x re-authperiod <Seconds> Example: set dot1x server-timeout User level: supervisor Use[...]

Chapter 2 Avaya C460 CLI Commands 86 Avaya C460 Reference Guide The syntax for this command is: set dot1x supp-timeout <Seconds> Example: set dot1x system-auth-control disable User level: superviso r Use the set dot1x system-auth-con trol disable command to globally disable the PBNAC (802.1x) feature. The syntax for this command is: set dot1x[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 87 • When a RADIUS server is not defined: set dot1x tx-period User level: supervisor Use the set dot1x tx-period command to set the time interval between attempts to access the Au thenticated Station. The syntax for this command is: Example: set dot1x tx-period <Seconds> set icmp-[...]

Chapter 2 Avaya C460 CLI Commands 88 Avaya C460 Reference Guide set inband vlan User level: read-write, admin. Use the set inband vlan command to set the inband management VLAN. The syntax for this command is: set inband vlan <vlan_num> Example: set intelligent -multicast User level: read-write, admin. Use the set intelligent-multicast comman[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 89 Example: set intelligent-mult icast group-filteri ng delay time User level: read-write, admin. Use the set intelligent-multicast group-filtering delay time command to set group filtering time delays . The syntax for this command is: set intelligent-multicast group-filtering-delay time [...]

Chapter 2 Avaya C460 CLI Commands 90 Avaya C460 Reference Guide set interface i nband User level: read-write, admin. Use the set interface inband command to configure the inband interface on the Supervisor Modu le. The syntax for this command is: set interface inband <vlan> <ip_addr> <netmask> Example: To configure the inband inte[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 91 To configure the outband interface on VLAN 1, IP addres s 149.4 9.75.174 and netmask 255.255.255.24 set interface ppp User level: read-write, admin. Use the set interface ppp command to configure the C460 Supervisor Module PPP interface IP parameters, exit modem mo de, disconnect the P[...]

Chapter 2 Avaya C460 CLI Commands 92 Avaya C460 Reference Guide set interface ppp {enable|enable-always|disable|off|reset} Example: Example: Example: set ip route User level: read-write, admin. Use the set ip route command to adds a route to the IP rout ing table. You can configure from 1 to 10 default static gateways for a C460 switch. The syntax [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 93 Example: This example shows h ow to add a defa ult route to the IP routing table: C460-1# set ip route 0.0.0.0 24 192.168.1.1 destination = 0.0.0.0 mask = 255.255.2 55.0 gateway = 192.168.1.1 done![...]

Chapter 2 Avaya C460 CLI Commands 94 Avaya C460 Reference Guide set license User level: read-write, admin. Use the set license command to activate a licensed feature on a specific C460 chassis. For a full description of the Feature Lice nse an d the installation procedure please refer to the Installation Guide provide d with the Feature License. Th[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 95 Example: To set the time until the system disconne cts an idle session automatically to 20 minutes: set mac-aging User level: privileged, supervisor. L This command is av ailable on the P33 0-ML switches only. Use the set mac-aging command to enable or disable the MAC aging function. T[...]

Chapter 2 Avaya C460 CLI Commands 96 Avaya C460 Reference Guide Example: L The entered value is the aging-time lowe r bound. The actual aging-time might be up to three minutes longer. set outband dup lex User level: read-write, admin. Use the set outband duplex command to configure the duplex type of the Ethernet Console port. You can configure the[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 97 The syntax for this command is: set outband negotiation {enable | disable} Example: set outband speed User level: read-write, admin. Use the set outband speed command to configure the speed of Ethernet Console port. In auto negotiation mode, the port's speed is determined by auto [...]

Chapter 2 Avaya C460 CLI Commands 98 Avaya C460 Reference Guide The syntax for this command is: set policy type <value> all | router Example: value all - apply policy to all packets entering the C460 through Fast Ethernet ports router - apply policy on routed packets only Router-1# set policy type all[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 99 set port auto-negotiati on- flowcontrol-advertise ment User level: read-write, admin. Use the set port auto-negotiation-flowcontrol-advertisement command to set the flowcontrol advertisem ent for a Gigabit port when performing autonegotiation. The syntax for this command is: set port a[...]

Chapter 2 Avaya C460 CLI Commands 100 Avaya C460 Reference Guide otherwise you will get an error message. L When adding a port t o an existing LA G, type the same LAG name, otherwise you will create a new LAG. The syntax for this command is: set port channel <port_list> {value} [name] If you wish to define a name which incl udes spaces, you m[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 101 set port disable User level: read-write, admin. Use the set port disable command to disable a port or range of ports. The syntax for this command is: set port disable [module>/<port] Example: set port dot1x i nitialize User level: admin. Use the set port dot1x initialize command[...]

Chapter 2 Avaya C460 CLI Commands 102 Avaya C460 Reference Guide set port dot1x max-req User level: ad min. Use the set port dot1x max-req command to set the maximal number of times the port tries to retransmit requests to th e Authenticate d Station before the session is terminated. The syntax for this command is: set port dot1x max-req <module[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 103 set port dot1x q uiet-period User level: admin. Use the set port dot1x quiet-period command to set the 802.1x quiet period per port. The syntax for this command is: set port dot1x quiet-period <module/port> <seconds> Example: set port dot1x re-authent icate User level: adm[...]

Chapter 2 Avaya C460 CLI Commands 104 Avaya C460 Reference Guide The syntax for this command is: set port dot1x re-authentication <module/port> <mode> Example: set port dot1x re-authperi od User level: ad min. Use the set port dot1x re-authper iod command to set the the idle time between re-authentication attempts before the s ession is[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 105 The syntax for this command is: set port dot1x server-timeout <module/port> <seconds> Example: set port dot1x sup p-timeout User level: admin. Use the set port dot1x supp-timeout command to set the time for the port to wait for a reply from the Authenti cation Server befor[...]

Chapter 2 Avaya C460 CLI Commands 106 Avaya C460 Reference Guide Example: set port duplex User level: read-write, admin. Use the set port duplex comma nd to configure the duplex type of an Ethernet or Fast Ethernet port or range of ports.Yo u can configure Ethernet and Fast Ethernet interfaces to either full duplex or half duplex. The duplex status[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 107 The syntax for this command is: set port edge admin state <module/port> <admin state> Examples: set port enable User level: read-write, admin. Use the se t port enable command t o enable a port or a range of ports. The syntax for this command is: set port enable [module/po[...]

Chapter 2 Avaya C460 CLI Commands 108 Avaya C460 Reference Guide Example: C460-1# set port enable 4/1 Port 4/1 enabled.[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 109 set port flowcontrol User level: read-write, admin. Use the set port flowcontrol command to set the send/receive mode for flow-control frames (IEEE 802.3x or prop rietary) for a full duplex port. Each direction (send or receive) ca n be configured separately. The syntax for this comma[...]

Chapter 2 Avaya C460 CLI Commands 110 Avaya C460 Reference Guide set port level User level: read-write, admin. Use the set port level command to set the priority level of a port or range of ports on the switching bus. Pack ets travelin g through a port set at normal priority should be served only after packets travelin g through a port set at high [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 111 Example: set port name User level: read-write, admin. Use the set port name command to configure a name for a port. If you do not specify a name, the port name remains blank. The syntax for this command is: set port name <module>/<port> [value] Example: If you wish to defi[...]

Chapter 2 Avaya C460 CLI Commands 112 Avaya C460 Reference Guide ports. The syntax for this command is: set port negotiation <module>/<port> {enable|disable} Example: To disable autonegot iation on port 1, module 4 : set port point- to-point adm in status User level: read-write, admin. Use the set port point-to-point admin status comman[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 113 Example: set port powerinline User level: read-write, admin. Use the set port powerinline command to enable or disable the load detection process on the port. The syntax for this command is: set port powerinline <module_number/port_number> {enable | disable} Example: To enable P[...]

Chapter 2 Avaya C460 CLI Commands 114 Avaya C460 Reference Guide Example: To enable PoE on ports 1 to 3 of module three to High: set port redun dancy User level: read-write, admin. Use the set port redundancy comm and to globally enables or disable the redundancy pairs you have defi ned. Using this command will not delete existing redundancy entrie[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 115 set port redundancy on/off User level: read-write, admin. Use the set port redundancy command to d efines or remove redundancy pairs. The link can be any port that does not belong to a LAG, or a LA G interface. Ensure that there is no redundancy scheme already defin ed on any of the l[...]

Chapter 2 Avaya C460 CLI Commands 116 Avaya C460 Reference Guide The syntax for this command is: set port redundancy-intervals <min-time-between-switchovers> <switchback-interval> | none Example: set port spantr ee User level: read-write, admin. Use the set port spantree c ommand to enable or disable the spanning tree mode for specific [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 117 set port spantree co st User level: read-write, admin. Use the set port spantree cost command to set the cost of a port. This value defines which port will be allowe d to forward traffic if two ports wit h different costs cause a loop. The syntax for this command is: set port spantree[...]

Chapter 2 Avaya C460 CLI Commands 118 Avaya C460 Reference Guide Example: set port span tree priority User level: read-write, admin. Use the set port spantree command to set the Spanning Tree priority level of a port. This value defines the priority of a po rt to be blocked in case two ports with the same costs cause a loop. The syntax for this com[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 119 Example: To configure port 1 on module 4 to 100 Mbps set port static-vlan User level: read-write, admin. Use the set port static-vlan command to assign static VL ANs to ports. The syntax for this command is: set port static-vlan [module/port range] [vlan num] Example: set port trap Us[...]

Chapter 2 Avaya C460 CLI Commands 120 Avaya C460 Reference Guide The syntax for this command is: set port trap <module>/<port> {enable|disable} Example: set port vlan User level: read-write, admin. Use the set port vlan command to set the port VLAN ID (PVID). If adding a new VLAN, the VLAN number must be within the range. L You need to [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 121 Example: set port vlan-binding-mode User level: read-write, admin. Use the set port vlan-binding-mode command to define the binding method used by ports. The syntax for this command is: set port vlan-binding-mode [port_list] [value] Example: set power redundancy User level: read-write[...]

Chapter 2 Avaya C460 CLI Commands 122 Avaya C460 Reference Guide The syntax for this command is: set power redundancy <mode> Example: set powerinline bud get User level: read-write, admin. Use the the set powerinline budget command to recalculate and reapply the PoE budget. The syntax for this command is: set powerinline budget Example: set p[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 123 Example: set ppp baud-rate User level: read-write, admin. Use the set ppp baud-rate command to define the baud rate used in PPP sessions. L You mujst set the peer baud rate to the same value as the host. The syntax for this command is: set ppp baud-rate <9600|19200|38400> Exampl[...]

Chapter 2 Avaya C460 CLI Commands 124 Avaya C460 Reference Guide The syntax for this command is: set ppp incoming timeout <time> Example: qset radius authenticat ion enable/disable User level: read-write, admin. Enables or disables RADIUS auth entication for the C460 switch. The syntax for this command is: set radius authentication {enable | [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 125 set radius authenticatio n retry-time User level: read-write, admin. Sets the time to wait before re-sending an access request. The syntax for this command is: set radius authentication retry-time <time> Example: set radius authenticatio n secret User level: read-write, admin. U[...]

Chapter 2 Avaya C460 CLI Commands 126 Avaya C460 Reference Guide Example: set radius authenti cation udp-port User level: read-write, admin. Sets the RFC 2138-approved UDP port number. Normally, the UDP port number should be set to its def ault value of 1812. Some early implementations of the RADIUS server u sed port number 1645. The syntax for thi[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 127 Example: 1 – if the slot is empty: Example: 2 – if there is a module in the slot:: set slot power priority User level: read-write, admin. Use the set slot power priority command to configure the power priority for a slot. C460-1> set slot power admin 4 up slot 4 power is enable[...]

Chapter 2 Avaya C460 CLI Commands 128 Avaya C460 Reference Guide The syntax for this command is: set slot power priority <slot> <level> Example: set snmp community User level: read-write, admin. Use the s et snmp community comman d to set or modify the switch’s SNMP community strings. The syntax for this command is: set snmp community[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 129 Example: set snmp timeout User level: read-write, admin. Use the set snmp timeout command to set the SNMP timeout in seconds. This command is useful for acce ss using the C460 Manager. The syntax for this command is: set snmp timeout <number> Example: set snmp trap User level: r[...]

Chapter 2 Avaya C460 CLI Commands 130 Avaya C460 Reference Guide Example: To enable SNMP ConfigChange traps to a specific manager: Example: To enable all traps to a specific manager: Example: To disable SNMP config traps to a specific manager: Example: To add an entry in the SNMP trap receiver table with default: set snmp trap au th User level: rea[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 131 set spantree default-path-cost User level: privileged, supervisor. Use the set spantree default-path-cost command to set the version of the spanning tree default path costs that are to be used by this bridge. The syntax for this command is: set spantree default-path-cost <path-cost[...]

Chapter 2 Avaya C460 CLI Commands 132 Avaya C460 Reference Guide set spantree forward-delay User level: read-write, admin. Use the set spantree forward-dela y command to set the bridge forward delay time parameter. The syntax for this command is: set spantree forward-delay <time> Example: set spantree hel lo-time User level: read-write, admin[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 133 The syntax for this command is: set spantree max-age <seconds> Example: set spantree priority User level: read-write, admin. Use the set spantree priority command to set the bridge priority for STP. The syntax for this command is: set spantree priority <bridge_priority> Ex[...]

Chapter 2 Avaya C460 CLI Commands 134 Avaya C460 Reference Guide Example: set spantree version User level: read-write, admin. Use the set spantree version command to set the rapid spanning tree state machine to work as "STP compatible". The syntax for this command is: set spantree version <version> Example: set system contact User l[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 135 set system location User level: read-only, read-write, admin. Use the set system location command to set the mib2 system location MIB variable The syntax for this command is: set system location [string] Example: If you wish to enter a n a me which includ es spaces, you must enclose t[...]

Chapter 2 Avaya C460 CLI Commands 136 Avaya C460 Reference Guide set time client User level: read-write, admin. Use the set time client command to e nable or disable the periodic network time acquisition by the switch from th e network time server (SNTP or TIME protocol). The syntax for this command is: set time client {enable|disable} Example: set[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 137 set time server User level: read-write, admin. Use the set time server command to set the TIME server address. The syntax for this command is: set time server <ip address> Example: set timezone User level: read-write, admin. Use the set timezone command to assign a timezone name[...]

Chapter 2 Avaya C460 CLI Commands 138 Avaya C460 Reference Guide set trunk User level: read-write, admin. Use the set trunk command to configure the VLAN tagging mode of a port. set trunk <module/port> [value] Example: set vlan User level: read-write, admin. Use the set vlan command to configure VLANs. The syntax for this command is: set vlan[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 139 If you wish to define a name which includes spaces , you must enclose the entire name in quotation marks, for example “new york”. set vlan (Layer 3) User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. [...]

Chapter 2 Avaya C460 CLI Commands 140 Avaya C460 Reference Guide Example: If you wis h to define a directory n ame which i ncludes s paces, you m ust enclose the entire name in quotation marks, for example “ne w york”. set welcome message User level: read-write, admin. Use the set welcome message command to set a welcome message to appear after[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 141 Example: show allowed manag ers status User level: read-only, read-write, admin. Use the show allowed managers status command to display the activation status of the Allowed Managers fea ture. The syntax for this command is: show allowed managers status Example: Router-1> show acce[...]

Chapter 2 Avaya C460 CLI Commands 142 Avaya C460 Reference Guide show allowed mana gers table User level: read-only, read-write, admin. Use the show allowed managers tab le to displa y the list of the twenty possible allowed managers IP addres ses. The syntax for this command is: show allowed managers table Example: C460-1(super)# show allowed mana[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 143 show arp-aging-i nterval User level: read-only, read-write, admin. Use the show arp-aging-interval command to display the ARP table aging interval for gateway entries. The syntax for this command is: show arp-aging-interval Example: show arp-tx-interval User level: read-only, read-wri[...]

Chapter 2 Avaya C460 CLI Commands 144 Avaya C460 Reference Guide Example: show banner post-lo gin User level: read-only, read-write, admin. Use the show banner login command to display the message shown after a successful login. The syntax for this command is: show banner post-login Example: show boot bank User level: read-only, read-write, admin. [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 145 The syntax for this command is: show broadcast storm control Example: show cam User level: read-only, read-write, admin. Use the show cam command to display the C AM table entries for a specific module and port. L MACs associated with LAGs appea r under the LAG ID, not under the LAG p[...]

Chapter 2 Avaya C460 CLI Commands 146 Avaya C460 Reference Guide Example: C460-1> show cam Total Matching CAM Entries Displayed = 128 Dest MAC/Route Dest vlan Destination Ports ------------------- ---- ----------------- 08:00:20:c6:98:5f 1 3/33 08:00:20:c4:c8:51 1 3/33 00:00:3b:80:49:7c 1 3/33 00:00:5e:00:01:01 1 3/33 00:00:5e:00:01:02 1 3/33 00[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 147 show cam mac User level: read-only, read-write, admin. Use the show cam mac command to display a specific mac/vlan in the CAM CAM table. The syntax for this command is: show cam mac <mac> <vlan> Example: show cam vlan User level: read-only, read-write, admin. Use the show [...]

Chapter 2 Avaya C460 CLI Commands 148 Avaya C460 Reference Guide show chassis-identi ty User level: read-only, read-write, admin. Use the show module-identity command to display the identifier(s) required for requesting license keys for this chassis. The syntax for this command is: show chassis-identity Example: show copy status User level: read-on[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 149 show cpu load User level: read-only, read-write, admin. Use the show cpu load command to show the current CPU utilization. The syntax for this command is: show cpu load Example: show cs User level: read-only, read-write, admin. Use the show cs command to show the version numbers of th[...]

Chapter 2 Avaya C460 CLI Commands 150 Avaya C460 Reference Guide show device-mode User level: read-only, read-write, admin. Use this command to display the switch operational mode (Layer 2 or Layer 3). The syntax for this command is: show device-mode Example: show dot1x User level: user, privileged, supervisor Use the show dot1x command to display [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 151 Example: show dynamic vlans Use the show dynamic vlans command to display automatically learne d VLANs.. The syntax for this command is: show dynamic vlans show environment f ans User level: read-only, read-write, admin. Use the show environment fans command to display the current fan[...]

Chapter 2 Avaya C460 CLI Commands 152 Avaya C460 Reference Guide show environment powe r User level: read-only, read-write, admin. Use the show environment power command to display the curre nt power configuration for the swit ch, the total power availa ble to the system, and amount of power currently in use. L The “Main Power” includes two sup[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 153 show erase status User level: user, privileged, supervisor Use the show erase status command to view the status of the erase configuration operation. The syntax for this command is: show erase status show event-log User level: read-only, read-write, admin. Displays the encrypted event[...]

Chapter 2 Avaya C460 CLI Commands 154 Avaya C460 Reference Guide The syntax for this command is: show fragment Example: show icmp-redirect User level: read-only, read-write, admin. Use the show icmp-redirect command to display whether ICMP-redirects are accepted or rejected. The syntax for this command is: show icmp-redirect Example: show image ver[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 155 The syntax for this command is: show intelligent-multicast Example: show interface User level: read-only, read-write, admin. Use the show interface command to display information on network interfaces . The syntax for this command is: show interface Example: show ip access-g roup User[...]

Chapter 2 Avaya C460 CLI Commands 156 Avaya C460 Reference Guide show ip access-list-dscp User level: user, privileged, supervisor Use th e show ip access-list-dscp command to display the DSCP to CoS map of a policy-list. The syntax for this command is: show ip access-list-dscp <policy-list-number> Example: show ip access-lists User level: re[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 157 Example: show ip access-list-summa ry User level: user, privileged, supervisor Use the show ip access-list-summary command to display a summary of policy lists. The syntax for this command is: show ip access-list-summary Example: show ip arp User level: read-only, read-write, admin. U[...]

Chapter 2 Avaya C460 CLI Commands 158 Avaya C460 Reference Guide Example: If you wish to define a name which incl udes spaces, you must enclose the entire name in quotation marks, for example “new york”. show ip icmp User level: read-only, read-write, admin. Use the show icmp ip command to display the status of ICMP error messages. The syntax f[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 159 show ip interface User level: read-only, read-write, admin. Use the show ip interface command to display informati on for an IP interface. The syntax for this command is: show ip interface [<interface-name>]|<ip-address>|<vlan>] Example: If you wish to define a name [...]

Chapter 2 Avaya C460 CLI Commands 160 Avaya C460 Reference Guide show ip inter face brief User level: read-only, read-write, admin. Use the show ip interface brief command to display brief information for an IP interface. The syntax for this command is: show ip interface brief [<interface> | <vlan> | <IP addr>] Example: show ip os[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 161 show ip ospf databa se User level: read-only, read-write, admin. Use the show ip ospf database command to display lists of information related to the OSPF database for a specific router. The syntax for this command is: show ip ospf database [{asbr-summary|router|network|network-summar[...]

Chapter 2 Avaya C460 CLI Commands 162 Avaya C460 Reference Guide If you wish to define a name which incl udes spaces, you must enclose the entire name in quotation marks, for example “new york”. show ip ospf neig hbor User level: read-only, read-write, admin. Displays OSPF -neighbor information on a per-interface basi s. The syntax for this com[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 163 show ip reve rse-arp User level: read-only, read-write, admin. Use the show ip reverse-arp command to display the IP address of a h ost, based on a known MAC address. The syntax for this command is: show ip reverse-arp <mac addr> [<match len>] Example: show ip route User l[...]

Chapter 2 Avaya C460 CLI Commands 164 Avaya C460 Reference Guide routing table. The syntax for this command is: show ip route show ip route best-match User level: read-only, read-write, admin. Use the show ip route best-match command to display a routing table for a destination address. The syntax for this command is: show ip route best-match <d[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 165 Example: show ip route summary User level: read-only, read-write, admin. Use the show ip route summary command to display the number of route s known to the switch. The syntax for this command is: show ip route summary Example: show ip traffic User level: read-only, read-write, admin.[...]

Chapter 2 Avaya C460 CLI Commands 166 Avaya C460 Reference Guide Example: Router-1> show ip traffic IP statistics: Received: 1365359 total, 45659 local destination 0 bad hop count, 0 packet header errors 0 unknown protocol, 136786 address errors 1182914 discarded Fragments: 0 reassembled, 0 timeouts 0 couldn't reassemble, 0 fragmented Sent:[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 167 show ip unicast cac he User level: read-only, read-write, admin. Use the show ip unicast cache command to list the entries in the hardware unicast cache database. The syntax for this command is: show ip unicast cache [<ip addr>] OSPF statistics: Received: 25783 total, 0 checksum[...]

Chapter 2 Avaya C460 CLI Commands 168 Avaya C460 Reference Guide Example: show ip unicast c ache networks User level: read-only, read-write, admin. Displays summary of networks handled by the hardware unicast cache database. The syntax for this command is: show ip unicast cache networks [<net addr> <net mask>] Example: Router-1> show[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 169 show ip unicast cac he networks de tailed User level: read-only, read-write, admin. Use the show ip unicast cache networks detailed command to list the networks and hosts that are handled by the hardware unicast cache database. The syntax for this command is: show ip unicast cache net[...]

Chapter 2 Avaya C460 CLI Commands 170 Avaya C460 Reference Guide show ip unicast c ache summary User level: read-only, read-write, admin. Use the show command to display the number of host networks and next-hops in the module’s unicast cache. The syntax for this command is: show ip unicast cache summary Example: show ip vrrp User level: read-only[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 171 show ip vrrp detai l User level: read-only, read-write, admin. Use the show ip vrrp detail command to display full VRRP- related information The syntax for this command is: show ip vrrp detail detail Show full detail informatio n[...]

Chapter 2 Avaya C460 CLI Commands 172 Avaya C460 Reference Guide Example: Router-1> show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN: 1 Router-id: 1 State: MASTER Priority: 255 Advertisement Interval: 1 Last State Change: 00:00:00 Override Address Ownership Rule: No Authentication Type: None Authentication Key: "" Ma[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 173 show l2-config User level: read-write, admin. Use the show l2-config command to display comprehensive Layer 2 configuration information. The syntax for this command is: show l2-config Example: C460-1> show l2-config !#################################################################[...]

Chapter 2 Avaya C460 CLI Commands 174 Avaya C460 Reference Guide !####################################################################### !# S P V I N F O !####################################################################### !# !# Slot #: 1 !# !# SPV state: Active !# !# Blade type: M460ML-SPV !# !# Blade-CS: 0.2 !# !# Serial #: 0000009 !# !# SW [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 175 !####################################################################### !# I O B L A D E I N F O !####################################################################### !# !# Slot #: 5 !# !# Blade type: M4612ML-G --type q to quit or space key to continue-- !# !# Blade-CS: 0.1 !# !# [...]

Chapter 2 Avaya C460 CLI Commands 176 Avaya C460 Reference Guide !# !#Set vlan table management parameters !# set vlan 1 name V1 !# !# Set the interface of the device !# !# set interface inband 1 149.49.50.233 255.255.255.0 !# !#Set PPP management parameters !# !#set interface ppp 0.0.0.0 0.0.0.0 --type q to quit or space key to continue-- !#set in[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 177 !# set intelligent-multicast parameters !# set intelligent-multicast disable set intelligent-multicast client-port-pruning time 600 set intelligent-multicast router-port-pruning time 1800 set intelligent-multicast group-filtering-delay time 10 !#******* broadcast storm configuration *[...]

Chapter 2 Avaya C460 CLI Commands 178 Avaya C460 Reference Guide !#*************** port 5/1 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/1 set port auto-negotiation-flowcontrol-advertisement 5/1 no-[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 179 !#*************** port 5/3 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/3 set port auto-negotiation-flowcontrol-advertisement 5/3 no-[...]

Chapter 2 Avaya C460 CLI Commands 180 Avaya C460 Reference Guide !#*************** port 5/6 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/6 set port auto-negotiation-flowcontrol-advertisement 5/6 no-[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 181 !#*************** port 5/9 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/9 set port auto-negotiation-flowcontrol-advertisement 5/9 no-[...]

Chapter 2 Avaya C460 CLI Commands 182 Avaya C460 Reference Guide !#*************** port 5/12 configuration ***************** !# Port type: Tranceiver Not Present !# Link status: no link !# STA status: Disabled !#********************************************************** set port disable 5/12 set port auto-negotiation-flowcontrol-advertisement 5/12 [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 183 show license User level: read-only, read-write, admin. Use the show license command to display the current licenses installed on the chassis The syntax for this command is: show license Example: show logout User level: read-only, read-write, admin. Use the show timeout command to disp[...]

Chapter 2 Avaya C460 CLI Commands 184 Avaya C460 Reference Guide Example: show mac-aging-time User level: user, privileged, supervisor Use the show mac-aging-time command to dis play the MAC aging time in minutes. The syntax for this command is: show mac-aging-time Example: L The displayed value is the aging-time lowe r bound. The actual aging-ti m[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 185 show module User level: read-only, read-write, admin. Use the show module command to display module status and information. The syntax for this command is: show module Example: Output Fields C460-1> show module Mod Type C/S S/N Status ---- ----------------- ---- -------- ------ 0 C[...]

Chapter 2 Avaya C460 CLI Commands 186 Avaya C460 Reference Guide show outband User level: read-only, read-write, admin. Use the show outband command to displays the Et hernet Console port status. This command applies to the specific su pervisor module where you execu te it. The syntax for this command is: show outband Example: show policy type User[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 187 show port User level: read-only, read-write, admin. Use the show port command to display port status on I/O modules. The syntax for this command is: show port [<module>[/port]] Example to display the status for port 4 on switch 3: Show Port Output Fields module (Optional) Number[...]

Chapter 2 Avaya C460 CLI Commands 188 Avaya C460 Reference Guide show port auto-neg otiation-flowcont rol-advertisement User level: read-write, admin. Use the show port auto-negotiation-flowcontrol-advertisement command to display the flowcontrol ad vertisement for a Gigabit port used to perform auto-negotiation. The syntax for this command is: set[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 189 Example: info Displays full information on the port C460-1> show port channel Port Channel Status Channel Name and Id ---- --------------- ------------- ------ 3/1 off 3/2 off 3/3 on server1 3/4 on server1 3/13 off C460-1> show port channel 3/3 info Port Speed Duplex Vlan Port T[...]

Chapter 2 Avaya C460 CLI Commands 190 Avaya C460 Reference Guide show port classif ication User level: read-write, admin. Use the show port classification command to display a port’s classification. The syntax for this command is: show port classification [module/[port]] Example: module Number of the module (3-6) . If you do not specif y a number[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 191 show port dot1x User level: read-only, read-write, admin. Use the show port dot1x command to display all the configurable val ues associated with the authenticator po rt access entity (PAE) and backend authenticator. The syntax for this command is: show dot1x [mod]/[port] Example: mod[...]

Chapter 2 Avaya C460 CLI Commands 192 Avaya C460 Reference Guide BEnd Stat The current state od the Backend Authentication state machine. Possible states include: •R e q u e s t •R e s p o n s e • Success • Fail •T i m e o u t •I d l e •I n i t Port Control Port control type. Valid values include: • force-authorized • force-unauth[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 193 show port dot1x statistics User level: read-only, read-write, admin. Use the show port dot1x statistics command to display all the port dot1x statistics. The syntax for this command is: show dot1x statistics [mod]/[port] Example: Max Req The maximum number of times a request for authe[...]

Chapter 2 Avaya C460 CLI Commands 194 Avaya C460 Reference Guide show port edge state User level: read-only, read-write, admin. Use the show port edge state command to show a port’s edge admin and operational RSTP state. L A port can be set to admin state of edge port, but if a BPDU is received on this port the oper state is change d to non-edge [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 195 Example: Output Fields show port mirror User level: read-only, read-write, admin. Use the show port mirror command to disp lay mirroring information for the switch. The syntax for this command is: show port mirror C460-1> show port flowcontrol 3/4 Port Send-Flowcontrol Receive-Flow[...]

Chapter 2 Avaya C460 CLI Commands 196 Avaya C460 Reference Guide Example: show port point -to-point status User level: read-only, read-write, admin. Use the show port point-to-point status command to show the port’s point-to-point admin and operational RSTP status. The syntax for this command is: show port point-to-point status <module/port>[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 197 show port redunda ncy User level: read-only, read-write, admin. Use the show port redundancy command to display info rmation about software port redundancy schemes defined for the switch. The syntax for this command is: show port redundancy Example: show port trap User level: read-onl[...]

Chapter 2 Avaya C460 CLI Commands 198 Avaya C460 Reference Guide show port vlan-b inding-mode User level: read-only, read-write, admin. Use the show port-vlan-binding command to display port vlan binding mode information. The syntax for this command is: show port vlan-binding-mode [module[/port]] Example: show powerinline User level: read-only, rea[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 199 Example to show PoE configuration on I/O module 3: Output fields: show powerinli ne budget User level: read-only, read-write, admin. Use the show powerinline budget command to display the PoE budget distribution for modules i n the switch. The budget assigned for the module includes p[...]

Chapter 2 Avaya C460 CLI Commands 200 Avaya C460 Reference Guide The syntax for this command is: show powerinline budget Example: show ppp authent ication User level: read-only, read-write, admin. Use the show ppp authentication command t o display the authentication method used for PPP s essions. The syntax for this comman d is: show ppp authentic[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 201 show ppp configurati on User level: read-only, read-write, admin. Use the show ppp configuration command to display the ppp configuration. The syntax for this command is: show ppp configuration Example: show ppp incom ing timeout User level: read-only, read-write, admin. Use this s ho[...]

Chapter 2 Avaya C460 CLI Commands 202 Avaya C460 Reference Guide show radius authenti cation User level: read-only, read-write, admin. Use the s how radius authentication command to display al l RADIUS authentication config urations. The syntax for this command is: show radius authentication Example: show rmon alarm User level: read-only, read-writ[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 203 Example: show rmon event User level: read-only, read-write, admin. Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command on Page 76 or using the C460 Manager. The syntax for this command is: show rmon event [<Event Index>] Exa[...]

Chapter 2 Avaya C460 CLI Commands 204 Avaya C460 Reference Guide show rmon history User level: read-only, read-write, admin. Use the show rmon history command to display the mo st recent RMON history log for a given His tory Index. The history index i s defined using the rmon history command on 76 or using an RMON management tool. The syntax for th[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 205 Example: show rmon2 dscp-st ats User level: read-only, read-write, admin. Use the show rmon2 dscp-stats command to display the DSCP distribution (routed traffic only) for the RMON2 application. The syntax for this command is: show rmon2 dscp-stats Example: C460-1> show rmon statist[...]

Chapter 2 Avaya C460 CLI Commands 206 Avaya C460 Reference Guide show rmon2 protoc ol-dir User level: read-only, read-write, admin. Use the show rmon2 protocol-dir command to display the protocols in the TCP/UDP protocols list. The syntax for this command is: show rmon2 protocol-dir [UDP|TCP <Port #>] Example: show rmon2 protoc ol-dist User l[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 207 Example: Router-1> show rmon2 protocol-dist Protocol Total Packets Total Octets Utilization ---------------------------------- -------------- -------------- ----------- ICMP 316 0.17% OSPF 5033 2.77% VRRP 0 0.00% RIP 0 0.00% Other 176031 97.06% Total IP control 181380 100.00% -----[...]

Chapter 2 Avaya C460 CLI Commands 208 Avaya C460 Reference Guide show rmon2 state User level: read-only, read-write, admin. Use the show rmon2 state command to display the status of the rmon2 application. The syntax for this command is: show rmon2 state Example: Router-1> show rmon2 state RMON2 15 in MATRIX state[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 209 show running-config User level: read-only, read-write, admin. Use the show running-config command to display the current router configuration information. The syntax for this command is: show running-config Example: Router-1> show running-config Router-1> ! Avaya Inc.- C460ML Mu[...]

Chapter 2 Avaya C460 CLI Commands 210 Avaya C460 Reference Guide show secure current User level: read-write, admin. Use the show secure current command to list the IP addresses of managers currently connected to the switch. The syntax for this command is: show secure current Example: C460-1# show secure current IP Address Time Since La st Request(I[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 211 show snmp User level: read-only, read-write, admin. Use the show snmp command to display SNMP inform ation. The syntax for this command is: show snmp Example: C460-1> show snmp Authentication trap disabled Community-Access Community-String ---------------- ---------------- read-onl[...]

Chapter 2 Avaya C460 CLI Commands 212 Avaya C460 Reference Guide show snmp retries User level: read-only, read-write, admin. Use the show snmp retries command to display the number of retries initiated by the C460 Manager when it tries to send SNMP messages to the device. The syntax for this command is: show snmp retries Example: show snmp timeout [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 213 Example: C460-1> show spantree Spanning tree enabled Designated Root: 00-40-0d-88-06-c8 Designated Root Priority: 32768 Designated Root Cost: 20 Designated Root Port: 1/1 Root Max Age: 20 Hello Time: 2 Bridge ID MAC ADDR: 00-40-0d-92-04-b4 Bridge ID priority: 32768 Port State Cost [...]

Chapter 2 Avaya C460 CLI Commands 214 Avaya C460 Reference Guide Output fields: show spv User level: read-only, read-write, admin. Use th e show spv command to display the fol lowin g information about supervisor modules: • Chassis MAC address • SPV status – active, standby, halted. • Indication whether the SPV’s are synchronized. • Sof[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 215 Example: C460-1> show spv Chassis In-band MAC address : 00.04.0D .17.A4.00 Chassis Out-band MAC address : 00.04.0D .17.A4.FE Chassis Serial number : 4552086 Chassis CS : 1.0 SPV 1 SPV 2 ------------------------ ----------------------- Mode | Standby | Active | Synchronized | Yes | [...]

Chapter 2 Avaya C460 CLI Commands 216 Avaya C460 Reference Guide show startup-config User level: read-only, read-write, admin. Use the show startup-config command to display the router startup configuration. Example: show startup-config Example: Router-1> show startup-config Router-1> ! Avaya Inc.- C460ML Multi-layer Sw itch - Router configur[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 217 show system User level: read-only, read-write, admin. Use the show system command to display the uptime, system name, location, contact person and MAC addresses. The syntax for this command is: show system Example: show system-log User level: read-only, read-write, admin. Displays the[...]

Chapter 2 Avaya C460 CLI Commands 218 Avaya C460 Reference Guide Example: C460-1> show system-log C460-1(super)# sh system-log --type q to quit or space key to continue-- *** UpTime : 0:37:19 *** *** MODULE : 1 *** System log file: H+n.AgDwZZioHgDZZZZ.(ioHgD3D3wD"bZZ.onD<ZZ2oAgDN~N}ZZAojgD 3Z gKgjiDZ!htllol ?glgi H+n.AgDwZZioHgDZZZZ.(ioH[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 219 show system-log (Layer 3) User level: read-only, read-write, admin. Displays the encrypted event log file. The syntax for this command is: show system-log [[slot]] show tftp download software status User level: read-only, read-write, admin. Use the show tftp download software status c[...]

Chapter 2 Avaya C460 CLI Commands 220 Avaya C460 Reference Guide Example: show time User level: read-only, read-write, admin. Use the show time command to display the current C460 time and timezone. The syntax for this command is: show time Example: show time parameters User level: read-only, read-write, admin. Use the show time parameters command [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 221 show timezone User level: read-only, read-write, admin. Use the show timezone command to display the current C460 time zone. The syntax for this command is: show timezone Example: show trunk User level: read-only, read-write, admin. Use the show trunk command to display VLAN tagging i[...]

Chapter 2 Avaya C460 CLI Commands 222 Avaya C460 Reference Guide show username User level: ad min. Use the show username command to display the local user accounts. The syntax for this comman d is: show username Example: show vlan User level: read-only, read-write, admin. Use the show vlan command to display the VLANs configured in the switch. The [...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 223 Example: show vlan (Layer 3) User level: read-only, read-write, admin. Use the show vlan command to display router Layer 2 interfaces. The syntax for this command is: show vlan Example: show web aux-files-url User level: read-only, read-write, admin. Displays the URL/directory from wh[...]

Chapter 2 Avaya C460 CLI Commands 224 Avaya C460 Reference Guide sync spv User level: read-write, admin. Use the sync spv command to synchronize the following between an Active Supervisor Module and H alted Supervisor M odule: • Boot bank • Firmware images • Device manager image L You can only execute this command from the active Supervisor M[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 225 terminal length User level: read-only, read-write, admin. Use the terminal length command to set the length of the terminal display in lines. The syntax for this command is: terminal length [<screen-length>] Example: terminal width User level: read-only, read-write, admin. Use t[...]

Chapter 2 Avaya C460 CLI Commands 226 Avaya C460 Reference Guide L You can only access these commands in the Router-RIP context. Type router rip at the command prompt to enter the Router-RIP context if necessary. Use the timers basic command to configure the route timer. Use the no timers basic command to restore the timers to their default values.[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 227 L The Invalid Route Timer value must be larger than the Update Timer value. It is recommended that it be at least three times greater. In any configuration all adjacent routers must have the same values for each of the timer parameters. It is possible to ha ve different values for the[...]

Chapter 2 Avaya C460 CLI Commands 228 Avaya C460 Reference Guide traceroute User level: read-only, read-write, admin. Provides a trace route utility. The syntax for this command is: traceroute <host> Example: tree User level: read-only, read-write, admin. Use the tree command to display a list of CLI commands available at the current user lev[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 229 Example: username User level: admin. Adds a local user account. L By default there is only a single user account, named 'root', with pas sword 'root', which access the administrator leve l. You cannot delete this basic user account, nor modify its access level, but[...]

Chapter 2 Avaya C460 CLI Commands 230 Avaya C460 Reference Guide Example: If you wish to define a name which incl udes spaces, you must enclose the entire name in quotation marks, for example “new york”. validate-group User level: read-write, admin. Use the validate-group command to verify that all th e rul es in a policy list are valid. L If t[...]

Chapter 2 Avaya C460 CLI Commands Avaya C460 Reference Guide 231 validate policy-list User level: read-write, admin. L If you are at the “read-write” user level, you can only access this command in Configure mode. Type configure at the command prompt to enter configure mode. Use the validate policy-list command to verify that all the ru les in [...]

Chapter 2 Avaya C460 CLI Commands 232 Avaya C460 Reference Guide[...]

Avaya C460 Reference Guide 233 Layer 2 CLI Commands B banner login 15 banner login line 15 banner post-login 15 banner post-login line 16 C clear cam 17 clear dynamic vlans 17 clear event-log 18 clear interface 19 clear ip route 19 clear log 20 clear port mirror 20 clear port static-vlan 21 clear power history 21 clear radius authentication server [...]

Layer 2 CLI Commands 234 Avaya C460 Reference Guide set arp-aging-int erval 81 set arp-tx-interval 81 set boot bank 223 set broadcast storm control 82 set broadcast storm control threshold 83 set device-mode 83 set dot1x max-req 84 set dot1x quiet-period 84 set dot1x re-authperiod 85 set dot1x server-timeout 85 set dot1x supp-timeout 85 set dot1x s[...]

Layer 2 CLI Commands Avaya C460 Reference Guide 235 timezone 221 show access lists 140 show allowed managers status 141 show arp-aging-interval 142 , 143 show arp-tx-interval 143 show banner login 143 show banner post-login 144 show boot bank 223 show broadcast storm control 144 show cam 145 show cam mac 147 show cam vlan 147 show copy status 148 s[...]

Layer 2 CLI Commands 236 Avaya C460 Reference Guide terminal width 225 tree 228 U username 229[...]

Avaya C460 Reference Guide 237 Layer 3 CLI Commands A access-list 13 arp 14 arp timeout 14 C clear arp-cache 16 clear event-log 18 clear fragment 18 clear ip route 19 clear ip traffic 20 clear log 20 clear power history 21 clear rmon2 statistics 22 clear screen 22 clear system-log 23 clear vlan 24 configure 25 copy running-config startup-config 25 [...]

Layer 3 CLI Commands 238 Avaya C460 Reference Guide ip vrrp 62 ip vrrp address 62 ip vrrp auth-key 63 ip vrrp override addr owner 63 ip vrrp preempt 64 ip vrrp primary 64 ip vrrp priority 65 ip vrrp timer 66 N network 67 network (RIP) 67 no area 13 no arp 14 no arp timeout 14 no default metric 30 , 31 no icmp-error 48 no interface 36 no ip access l[...]

Layer 3 CLI Commands Avaya C460 Reference Guide 239 show ip access- list-summary 157 show ip arp 157 show ip icmp 158 show ip interface 159 show ip ospf 160 show ip ospf database 161 show ip ospf interface 161 show ip ospf neighbor 162 show ip protocols 162 show ip reverse-arp 163 show ip route 163 show ip route best-match 164 show ip route static [...]

Layer 3 CLI Commands 240 Avaya C460 Reference Guide[...]

Avaya C460 Reference Guide 241 Glossary 100BASE-TX 100-Mbps baseband Fast Ethernet specification based on the IEE E 802.3 standard. 100BaseTX uses two pairs of either UTP (Unshielded Twiste d Pair) or STP (Single Twisted Pair) wiring. One pair is used to re ceive data; the other is used to transmit data. 10BASE-T 10-Mbps baseband Ethernet specif ic[...]

Gl ossary 242 Avaya C460 Reference Guide Beaconing An error detection mechanism in Token Ring networks. When a station detects a serious network problem, it sends a Beacon Frame. The Beacon Frame defines a failure domain that includes the station reporting the fail ure, its nearest active upstream neighbor, and everything in between. Beaconing init[...]

G lossary Avaya C460 Reference Guide 243 BUS Broadcast and Unknown Server. A multicast server used in ELANs that is used to forward multicast and broadcast traffic to the appropriate clients. CAM Content Address Memory. A list kept by ea ch port containing the addresses of all network elements connected to the port. CA M is accessed according to it[...]

Gl ossary 244 Avaya C460 Reference Guide different IP address every time it connects to the network. In some systems, the device's IP address can even change while it is stil l connected. DHCP also supports a mix of static and dynamic IP addresses. Domain A group of computers and devices on a networ k that are administered as a unit wit h comm[...]

G lossary Avaya C460 Reference Guide 245 area networks. FDX Full Duplex. A circuit or device permitting simultaneous data transmission between sending and receiving stations. For more information, refer to Duplex Mode on page 244. Flow Control Avaya’s devices use a proprietary form of fl ow control that enables one endpoint to inform another endp[...]

Gl ossary 246 Avaya C460 Reference Guide Host A computer, attached to a network, that provides services to another computer beyond simply storing and forwarding information. HTTP Hyper Text Transmission Protocol. The pr otocol used betwee n clients and servers on the World Wide Web for tran smission of HTML documents. Hub A common connection point [...]

G lossary Avaya C460 Reference Guide 247 Internet A collection of networks and gateways that use the TCP/IP suite of protocols. An internet is two or more networks connecte d by an internal or external router. The word “internet” is a generic term. “The Internet” is the world’s largest internet. Interswitch Link (ISL) Interswitch Link. An[...]

Gl ossary 248 Avaya C460 Reference Guide LAG Link Aggregation Groups (LAGs) provide a method of creating a high-bandw idth link. A LAG consists of a group of ports ac ti ng as a single logical port. All ports participating must have the same configuration. LAN Local Area Network. A high-speed, low-e rror data network that spans a lim ited area. LAN[...]

G lossary Avaya C460 Reference Guide 249 use standardized MIB formats that enable any SNMP and RMON tool to monitor any device defined by a MIB . Module A self-contained communicati ons unit that may be used in combination with other units. Examples include indi vidual Avaya P330 units and cards that slot into the Avaya P580/P882 Device. Multicasti[...]

Gl ossary 250 Avaya C460 Reference Guide OID Object Identifier. Used in SNMP to id entify managed objects. In the SNMP Manager/Agent Network Management Para digm, each managed object must be identified by a unique OID. OSI Open Systems Interconnection reference model. A model fo r network communications consisting of seven laye rs that describe wha[...]

G lossary Avaya C460 Reference Guide 251 Protocol A set of rules and conventions that governs how devices exchange data, especially across a network. Low level protocols define t he electrical and physical standards to be observed, bit- and byte-ordering, the transmission, error detection, and correction of the bi t stream . High lev e l protocols [...]

Gl ossary 252 Avaya C460 Reference Guide RIP Routing Information Protocol. Specifies how routers exchange routing table information. RIP is gradually being replaced by a newer protocol called OSPF (Open Shortest Pa th First). RMON Remote Monitoring. A network manageme nt standard that allows network information to be gathered at a single work stati[...]

G lossary Avaya C460 Reference Guide 253 SLIP Serial Line Internet Protocol . SLIP is the standard protoc ol for point-to-point serial connections, using a variation of TCP/IP. SMON Switch Monitoring, Avaya’s proprietary switch monitoring technology. SMON extends the RMON standard to provide addi tional tools and features for monitoring in the sw[...]

Gl ossary 254 Avaya C460 Reference Guide selected bridge interfaces. Stack A layered set of protocols which work together to provide a set of network functions. Each intermediate layer uses the layer below it to provide a service to the layer above. Standalone Mode An option to separate a module from t he ot her modules in a device so that its bus [...]

G lossary Avaya C460 Reference Guide 255 Transceiver A device that both transmits and receives analog or digital signals. Usually used to describe the LAN component that applies si gnals onto the network wire and detects signals passing through the wire. Trap Message sent by an SNMP agent to an NMS, console, or terminal to indicate the occurrence o[...]

Gl ossary 256 Avaya C460 Reference Guide[...]