Axis Communications network camera manuale d’uso

USER MANUAL AXIS P3364-VE Network Camera[...]

About this Document This manual is intended for administrators and users of the AXIS P3364–VE Fixed Dome Network Camera, and is applicable to rmware 5.40 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Lin[...]

Battery The Axis product uses a 3.0 V BR/CR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of ve years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appea[...]

AXIS P3364-VE Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

AXIS P3364-VE Network Camera Table of Contents Symptoms, Possible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . . . . 55 Technical Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

AXIS P3364-VE Network Camera Hardware Overview Hardware Overview 1 0 11 1 2 2 1 3 4 5 6 7 8 9 1 4 1 3 1. Camera unit 2. Network connector (PoE) 3. Audio out 4. LED connectors 5. Audio in 6. I/O connector 7. Control button 8. Fan output connector 9. SD memory card slot 10. Mounting bracket 11. Network cable 12. Unit casing 13. Serial number 14. Heat[...]

AXIS P3364-VE Network Camera Hardware Overview Network Connector RJ45 Ethernet connector. Supports Power over Ethernet (PoE). NOTICE NOTICE NOTICE The product shall be connected using a shielded network cable (STP) or an optical ber cable. All cables connecting the product to the network shall be intended for their specic use. Make sure that [...]

AXIS P3364-VE Network Camera Hardware Overview Green Steady green for normal operation. Amber Steady during startup and when restoring settings. Status Red Slow ash for failed upgrade. Green Normal operation. Power Amber Flashes green/amber during rmware upgrade. Note • The Status LED can be congured to be unlit during normal operation. [...]

AXIS P3364-VE Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems[...]

AXIS P3364-VE Network Camera Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must congure your network router to allow incoming data trafc to the product. To do this, enable the NAT-traversal feature, which will attempt to au[...]

AXIS P3364-VE Network Camera Accessing the Product Set Power Line Frequency Power line frequency is set the rst time the Axis product is accessed and can only be changed from Plain Cong (see page 52 ) or by resetting the product to factory default. Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Sele[...]

AXIS P3364-VE Network Camera Accessing the Product Click the Active/Inactive buttons to manually activate and inactive the product’s output port. For information about how to enable and congure output buttons, see page 28 . The Manual Trigger button is used to trigger an action rule from the Live View page. For information about how to cong[...]

AXIS P3364-VE Network Camera Accessing the Product The Snapshot button takes a snapshot of the video image. The location where the image is saved can be specied in the AMC Control Panel. Click the View Full Screen button and the video image will ll the entire screen. Press ESC (Escape) on the computer keyboard to cancel full screen view. The [...]

AXIS P3364-VE Network Camera Accessing the Product Pan and Tilt bars – Use the arrows to pan and tilt the camera view, or click on a position on the bar to steer the camera view to that position. The PTZ controls can be disabled under PTZ > Advanced > Controls , see Controls, on page 31 . 14[...]

AXIS P3364-VE Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream p[...]

AXIS P3364-VE Network Camera Media Streams The AMC Control Panel can be used to congure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on rst use, after which it can be congured. Open the AMC Control Panel from: • Windows Control P[...]

AXIS P3364-VE Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. Accessing Audio Streams The Live View pa[...]

AXIS P3364-VE Network Camera Setting Up the Product Setting Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to [...]

AXIS P3364-VE Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can congure the following: • Video stream settings. See page 19 . • Stream proles. See page 20 . • Camera settings. See page 21 . • View area. See page 23 . • Overlay image. See page 23 . •[...]

AXIS P3364-VE Network Camera Video and Audio • Resolution . Select the default resolution. • Compression . The compression level affects the image quality, bandwidth and le size of saved images; the lower the compression, the higher the image quality with higher bandwidth requirements and larger le sizes. • Rotate image . If required, t[...]

AXIS P3364-VE Network Camera Video and Audio • When setting up continuous recording. See Continuous Recording, on page 41 . • In the Live View page – select the stream prole from the Stream prole drop-down list. For quick setup, use one of the predened stream proles. Each predened prole has a descriptive name, indicating its[...]

AXIS P3364-VE Network Camera Video and Audio Exposure zones - This settings determines which part of the image is used to calculate the exposure. For most situations, the Auto setting can be used. For particular requirement, select a predened area. Shutter & Gain The shutter and gain settings affect the amount of motion blur and noise in the[...]

AXIS P3364-VE Network Camera Video and Audio The Day/Night shift level bar helps determine when the camera will shift from day mode to night mode. Normally, the camera automatically changes mode from day to night when very dark (level 100 in the slider). By setting Day/Night shift level to a lower value, the camera will change to night mode earlier[...]

AXIS P3364-VE Network Camera Video and Audio Overlay Image An overlay image is a static image superimposed over the video stream. The image, for example company logo, is used to provide extra information or to mask a part of the image. Since it is static, the position and size of an overlay image will remain the same regardless of resolution and Pa[...]

AXIS P3364-VE Network Camera Video and Audio 5. If more adjustments are needed, go to the Advanced tab. Note • Changing the zoom level moves the focus position. Focus should always be adjusted after changing the zoom. • Movements in front of the camera should be avoided during automatic focusing. On the Advanced tab, focus can be adjusted manua[...]

AXIS P3364-VE Network Camera Video and Audio To use a professional microphone requiring 48 V phantom power, you need an external power supply and a balanced-unbalanced converter (audio transformer) in between. Use the Input gain to control the volume (dB Full Scale) of the audio input. If the sound is too low, choose a higher dB, to amplify the sou[...]

AXIS P3364-VE Network Camera Live View Cong Live View Cong You can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 20 . • Default Viewer for Browser. See page 27 . • Viewer Settings. See page 28 . • Action Buttons. [...]

AXIS P3364-VE Network Camera Live View Cong Browser Viewer Description AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alternative to AMC (Motion JPEG). Requires one of the following installed on the client: • JVM (J2SE) 1.4.2 or higher. • JRE (J2SE) 5.0 or higher. Windows Intern[...]

AXIS P3364-VE Network Camera Live View Cong - Pulse activates the output for a dened period of time. The pulse time can be set from 1/100 second to 60 seconds. - Active/Inactive displays two buttons, one or each action. To congure the active and inactive states, go to System Options > Ports & Devices > I/O Ports and set the port?[...]

AXIS P3364-VE Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Area, on page 23 . Preset Positions A preset position is a predened view that can be used to quickly steer the camera to a specic [...]

AXIS P3364-VE Network Camera PTZ (Pan Tilt Zoom) 1. Go to PTZ > Guard Tour and click Add . 2. Enter a descriptive name. 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the View Time in seconds or minutes. 6. Specify the View Order or select the Random view order option. 7. Click Save [...]

AXIS P3364-VE Network Camera Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. To send an alarm, for example an email, an action rule must be set up. To congure tampering: 1. Go to Detectors > Camera Tampering . 2. Set th[...]

AXIS P3364-VE Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window. Set Up Motion Detectio[...]

AXIS P3364-VE Network Camera Detectors Medium level (50%) A large difference in luminance is required to trigger motion detection. Low level (0%) Even very small objects trigger motion detection. An object that appears in the window triggers motion detection only for a very short time before it is considered as non-moving. Only very bright objects [...]

AXIS P3364-VE Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downl[...]

AXIS P3364-VE Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 36[...]

AXIS P3364-VE Network Camera Events Events The Axis product can be congured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that denes how and when the action is triggered is called an Action Rule . Available action rule triggers and conditions include: • Applicat[...]

AXIS P3364-VE Network Camera Events • System - System Initializing – Trigger the rule when the product is being started. This can for example be used to send a notication when the product restarts. • Time - Recurrence – Trigger the rule periodically. See Recurrences, on page 40 . This can for example be used to upload an image every 5 mi[...]

AXIS P3364-VE Network Camera Events 8. Select Network Share from the Storage drop-down list. To add additional criteria, select the Additional conditions option and add additional triggers. To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger sh[...]

AXIS P3364-VE Network Camera Events To use the schedule in an action rule, select the schedule from the Schedule drop-down list in the Action Rule Setup page. Recurrences Recurrences are used to trigger action rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add . 2. Ent[...]

AXIS P3364-VE Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 41 . • To set up action rules, see page 38 . • To access recordings, see Recording List, on page 41 . • To congure camera controlled storage, see S[...]

AXIS P3364-VE Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may [...]

AXIS P3364-VE Network Camera System Options IEEE 802.1X IEEE 802.1X is a standard for port-based Network Admission Control providing secure authentication of wired and wireless network devices. IEEE 802.1X is based on EAP (Extensible Authentication Protocol). To access a network protected by IEEE 802.1X, devices must authenticate themselves. The au[...]

AXIS P3364-VE Network Camera System Options To change the date and time settings, select the preferred Time mode under New Server Time : • Synchronize with computer time – Sets date and time according to the computer’s clock. With this option, date and time are set once and will not be updated automatically. • Synchronize with NTP Server ?[...]

AXIS P3364-VE Network Camera System Options Assign IP Address Using ARP/Ping The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power. 1. Acquire a free static IP address on the same network segment as the computer. 2. Locate the serial number (S/N) on the product label. 3. Open a[...]

AXIS P3364-VE Network Camera System Options AXIS Internet Dynamic DNS Service AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www.axiscam.net To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic . Under Services ,[...]

AXIS P3364-VE Network Camera System Options HTTP The HTTP port used by the Axis product can be changed under System Options > Network > TCP/IP > Advanced . In addition to the default setting, which is 80, any port in the range 1024–65535 can be used. HTTPS The HTTPS port used by the Axis product can be changed under System Options > N[...]

AXIS P3364-VE Network Camera System Options Note H.264 video streams will not be available if the RTSP server is disabled. SOCKS SOCKS is a networking proxy protocol. The Axis product can be congured to use a SOCKS server to reach networks on the other side of a rewall or proxy server. This functionality is useful if the Axis product is locat[...]

AXIS P3364-VE Network Camera System Options SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required. To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 42 . To enable SNMP v3, check the box and provide the initial user password. Note The initial password can only be set once.[...]

AXIS P3364-VE Network Camera System Options Mounting is done automatically when the card is inserted or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted. To unmount the SD card: 1. Go to System Options > Storage and click SD Card . 2. Click Unmount . 3. The card can now b[...]

AXIS P3364-VE Network Camera System Options Maintenance The Axis product provides several maintenance functions. These are available under System Options > Maintenance . Click Restart to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current settings. Note A restart clears all entries i[...]

AXIS P3364-VE Network Camera System Options Access Log - Lists all failed attempts to access the product. The Access Log can also be congured to list all connections to the product (see below). Server Report - Provides information about the product status in a pop-up window. The Access Log is automatically included in the Server Report. You can [...]

AXIS P3364-VE Network Camera System Options Note The installation and management software tools are available on the CD supplied with the product and from the support pages on www.axis.com/techsup To reset the product to the factory default settings: 1. Disconnect power from the product. 2. Press and hold the control button and reconnect power. See[...]

AXIS P3364-VE Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. The[...]

AXIS P3364-VE Network Camera Troubleshooting Emergency Recovery Procedure If power or network connection is lost during the upgrade, the process fails and the product becomes unresponsive. Flashing red Status indicator indicates a failed upgrade. To recover the product, follow the steps below. The serial number is found on the product’s label. 1.[...]

AXIS P3364-VE Network Camera Troubleshooting The IP address has been changed by DHCP IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been changed, use AXIS IP Utility or AXIS Camera Management to locate the product on the network. Identify the product using its model or serial number, or by the DNS name (i[...]

AXIS P3364-VE Network Camera Troubleshooting Lower frame rate than expected See Performance Considerations, on page 61 . Reduce the number of applications running on the client computer. Limit the number of simultaneous viewers. Check with the network administrator that there is enough bandwidth available. Check in the AMC Control Panel (H.264 tag)[...]

AXIS P3364-VE Network Camera Technical Specications Technical Specications Function/group Item Specications Models AXIS P3364-VE Image sensor Progressive scan RGB CMOS 1/3” Lens Varifocal, remote focus and zoom, P-iris, IR corrected, mexapixel resolution 6 mm models : 2.5–6 mm, F1.2, horizontal angle of view: 105°–108°, vertical an[...]

AXIS P3364-VE Network Camera Technical Specications Function/group Item Specications Security Password protection, IP address ltering, HTTPS encryption*, IEEE 802.1X network access control*, digest authentication, user access log *This product includes software developed by the Open SSL Project for use in the Open SSL Tool kit ( www.openss[...]

AXIS P3364-VE Network Camera Technical Specications Function/group Item Specications Operating conditions -40 to 55 °C (-40 to 131 °F), humidity 10–100% RH (condensing) Storage temperature -40 to 70 °C (-40 to 158 °F) Approvals EN 55022 Class B, EN 50121-4, IEC 62236-4, EN 61000-3-2, EN 61000-3-3, EN 55024, EN 61000-6-1, EN 61000-6-2 FC[...]

AXIS P3364-VE Network Camera Technical Specications DC output 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out. 3.3 V DC Max load = 50 mA Digital Input 3 Connect to pin 1 to activate, or leave oating (unconnected) to deactivate 0 to max 40 V DC Digital Output 4 Connected to pin 1 when activated, oati[...]

AXIS P3364-VE Network Camera Technical Specications The following factors are among the most important to consider: • High image resolution and/or lower compression levels result in images containing more data. Bandwidth affected. • Access by large numbers of Motion JPEG and/or unicast H.264 clients. Bandwidth affected. • Simultaneous view[...]

User Manual Ver. M3.3 AXIS P3364-VE Network Camera Date: March 2014 © Axis Communications AB, 2012 - 2014 Part No. 54964[...]