Barco 5MP1HM manuale d’uso

M E D IS 5MP1HM S ystem Manual[...]

B410046 / 00 July 2003 © 2003 BARCO NV . All rights reserved BarcoView Theodoor Sevenslaan 106 8500 K ortrijk, Belgium Phone: +32(0)56 23 32 44 F ax: +32(0)56 23 33 74 E-mail: sales.medical@barco.com http://www .barco view .com BarcoView Inc 3059 Premiere Parkway Duluth, Georgia, 30097,USA Phone: +1 678 475 8000 F ax: +1 678 475 8100 E-mail: sales[...]

System manual MeDis 5MP1HM 3 CONTENTS Introduction ....................................................................................................... 7 Introduction ......................................................................................................... 9 Contents of the p ackage ...............................................[...]

Driver Installation ..................................................................................... 31 BARCO DPMS Screen Saver Inst allation ......................... ....................... 35 Setting the Resolution of Y our 5MP1HM .............. .................................. 38 Reinstalling or Updating your BarcoMed 5MP2 AURA, 5MP2, 5M[...]

W ork Schedule ........................................................................................ 70 Beg in Work Day ....................................................................................... 70 End W ork Day .......................................................................................... 70 Screen Saver During W ork Da[...]

Important considerations .............................................................................. 97 Operation: User controls ................................................................................... 98 Switching on / off .......................................................................................... 98 Contrast and brigh[...]

System manual MeDis 5MP1HM 7 INTRODUCTION[...]

System manual MeDis 5MP1HM 8 (This page intentionally left blank.) Introduction[...]

System manual MeDis 5MP1HM 9 INTRODUCTION BARCO MeDis ® 5MP1H is a total display solution for medical applications. This can be a sing le-head or multi-head system. MeDis comes with everything you need to set-up a complete viewing system, from video cables to displays. Content s of the p ackage Please refer to the packing list on the outside of th[...]

System manual MeDis 5MP1HM 10 (This page intentionally left blank) Introduction[...]

System manual MeDis 5MP1HM 11 DISPLA Y CONTROLLER INST ALLA TION[...]

System manual MeDis 5MP1HM 12 (This page intentionally left blank.) Display Controller installation[...]

System manual MeDis 5MP1HM 13 BarcoMed 5MP1HM Product Overview The BarcoMed 5MP1HM Display Controller delivers a quality 2048 x 2560 pixel image with 1024 simultaneous shades of gray for medical imaging applications. The BarcoMed 5MP1HM includes features specifically designed to meet the demands of mammography . Features of the BarcoMed 5MP1HM  [...]

System manual MeDis 5MP1HM 14 (This page intentionally left blank.) Display Controller installation[...]

System manual MeDis 5MP1HM 15 HARDW ARE INST ALLA TION Notice: W ear a protective ESD strap during installation or handling of the controller . Electrostatic charges can damage the controller . Familiarizing Yourself With the 5MP1HM Prior to installing your 5MP1HM controller(s) in your PC please take a few minutes to familiarize yourself with both [...]

System manual MeDis 5MP1HM 16 should now remove any third party VGA controller from your system or disable the integrated VGA controller . If you decide to use a separate VGA card and monitor as your boot monitor , you must disable the on-board VGA capabilities of the BarcoMed 5MP1HM by moving the jumper to the bottom two pins at J- 1. Figure 2: VG[...]

System manual MeDis 5MP1HM 17 Installing the BarcoMed 5MP1HM Display Controller Install the 5MP1HM into your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord. 2. Remove the chassis cover according to the manufacturer s instructions. Be sure to observe safety warnings. 3. If you have decided to [...]

System manual MeDis 5MP1HM 18 Figure 4: The Video Outputs. : 1 D I Vy a l p s i d t s r i f e h t r o f r o t c e n n o c ) n e e r g ( o e d i V e h t t c e n n o C . e r e h : S Ht s 1 e h t r o f r o t c e n n o c ) k c a l B ( c n y S l a t n o z i r o H e h t t c e n n o C . e r e h y a l p s i d : S Vt s 1 e h t r o f r o t c e n n o c ) e t [...]

System manual MeDis 5MP1HM 19 DISPLA Y INST ALLA TION[...]

System manual MeDis 5MP1HM 20 (This page intentionally left blank.) Display installation[...]

System manual MeDis 5MP1HM 21 DISPLA Y INST ALLA TION Example An example of a correct set-up is shown in figure 5. Please take a good look at the figures, and then read the rest of the text very carefully . #1 #2 Display #1 (rear view ) Display #2 (rear view) Video cable #1 Video cable #2 Remote cable Remote cable PC Video cable from PC graphic boa[...]

System manual MeDis 5MP1HM 22 Placing and configuring the displays 1 The last part of this system manual is a copy of the display user manual. Follow the precautions and guidelines from this part. 2 The display(s) from the MeDis system are numbered. E.g., in a quad-head system, the displays are numbered 1 to 4. Y ou can find the number of the displ[...]

System manual MeDis 5MP1HM 23 Connection of the Remote cables Note : One of the remote cables is packed inside the MediCal box. 1 The Remote cables that come with MeDis are not numbered. It does not matter which cable you connect to which display , as long as you take the Remote inputs and outputs on the displays into account. 2 T ake one of the re[...]

System manual MeDis 5MP1HM 24 (This page intentionally left blank.) Display installation[...]

System manual MeDis 5MP1HM 25 BARCOMED DRIVER AND SOFTW ARE INST ALLA TION[...]

System manual MeDis 5MP1HM 26 (This page intentionally left blank.) BarcoMed driver and sof tware installation[...]

System manual MeDis 5MP1HM 27 Planning Y our Barcomed Windows 2000 Installation Because of W indows 2000s Plug and Play features, it is very important to carefully plan your BarcoMed Board Hardware and Software installation and install the device drivers in the same sequence that the boards are installed in the PCI slots. When inst alling BarcoM[...]

System manual MeDis 5MP1HM 28 If you choose to install multiple types of BarcoMed Imaging Boards in your computer it is important to carefully note which PCI slot each board is in and then install the drivers for each type of board based on the PCI slot they are installed in. If you are using the VGA Capabilities of a BarcoMed Imaging Board it is i[...]

System manual MeDis 5MP1HM 29 Inst alling the BarcoMed 5MP2 AURA, 5MP2, 5MP1HM, 5MP1H or 4MP2 Windows 2000 Software SPECIAL NOTE: Prior to installing the BarcoMed drivers and related software you MUST install the BarcoMed Display Controller(s), connect the high resolution display(s) to the card(s), and turn the high resolution display(s) on. Refer [...]

System manual MeDis 5MP1HM 30 contents of your BarcoMed Software CD and double click on the file: Setup.exe to start the wizard. The BarcoMed Product Inst allation W izard will start by inspecting your system to make certain that all of the Windows components it needs are up to date. If it determines that the Microsoft Installer is current, t[...]

System manual MeDis 5MP1HM 31 Figure 7 Driver Installation 7. Click Next on the Display Driver Wizards Welcome Screen to continue or Cancel to exit the Display Driver Wizard and return to the Software Inst all W izard. 8. The Device Selection Screens dialog box should show only those devices physically installed and supported by t[...]

System manual MeDis 5MP1HM 32 Figure 8 Click OK to continue. If you dont want to replace the exiting driver , click OK and then click Cancel . 10. If you are installing the BarcoMed 5MP1HM or 5MP1H skip to step1 1. S tep 10 applies to the 5MP2 AURA, 5MP2 and 4MP2 only . Y our selection on the Enable DualView screen det[...]

System manual MeDis 5MP1HM 33 Figure 10: 5MP2 AURADualView Enabled If you wish to enable DualView check the checkbox next to Enable the DualView device?, and click Next . If you do not wish to enable DualView simply click Next to continue. 1 1. The Device Confirmation screen displays the device driver that will be i[...]

System manual MeDis 5MP1HM 34 Figure 1 1 14. Wh en the Wizard tells you that it has successfully installed the selected driver , click Finish . The wizard will now begin installing the next selected piece of BarcoMed Software. If you are working with the default selections, this will be the BARCO DPMS InstallShield W izard. Please turn to the[...]

System manual MeDis 5MP1HM 35 to enable DualView , you will need to reinstall the drivers with the Enable the DualView device? checkbox checked. Figure 12 BARCO DPMS Screen Saver Installation 15. Click Next on the W elcome Screen of the BARCO DPMS InstallShield W izard to begin the installation. Click Cancel t o cancel the DPMS in[...]

System manual MeDis 5MP1HM 36 Figure 13 17. The Setup T ype page will now appear (figure 14). Choose T ypical to install the default schemes with English names. Choose Custom to install the default schemes with either Dutch or German names. Currently the default schemes are not supported in the Japanese, Korean and Chinese languag[...]

System manual MeDis 5MP1HM 37 During installation the wizard will display a progress screen. 19. When the InstallShield Wizard Completed page appears, click Finish . 20. The wizard will now display the screen shown in figure 15 below . If you are finished installing your BarcoMed Software, click Finish to exit the BarcoMed Product[...]

System manual MeDis 5MP1HM 38 Setting the Resolution of Your 5MP1HM 1. T o set the resolution for your high resolution display(s), right click on the desktop and select Properties . Select the Settings ta b (see figure 16). Now select the rectangle that represents the virtual display of the BarcoMed 5MP1HM Display Controller you are wor[...]

System manual MeDis 5MP1HM 39 s n o i t u l o s e R e l p m a S r e l l o r t n o C n o i t a r u g i f n o C y a l p s i D n o i t u l o s e R p o t k s e D l a u t r i V n o i t u l o s e R A R U A 2 P M 5 e n O a n i s y a l p s i d 2 w o r e l g n i s 0 6 5 2 x 8 4 0 20 6 5 2 x 6 9 0 4 A R U A 2 P M 5 e n O a n i s y a l p s i d 2 n m u l o c e[...]

System manual MeDis 5MP1HM 40 Figure 16: The Windows 2000 Display Properties Control Panel Settings T ab after the drivers have been installed and the resolution set. Note: The system shown in figure 16 above is a single BarcoMed Display Controller , no 3 rd party VGA card configuration, your system may look different. Reinstalling or Updating your[...]

System manual MeDis 5MP1HM 41 Planning Y our Barcomed Windows XP Installation Because of W indows XPs Plug and Play features, it is very important to carefully plan your BarcoMed Board Hardware and Software installation and install the device drivers in the same sequence that the boards are installed in the PCI slots. When inst alling BarcoMed 5[...]

System manual MeDis 5MP1HM 42 If you have previously installed drivers for the BarcoMed Display Controllers in your Windows XP System, Windows XP should identify the board by their correct BarcoMed name. However , while updating the drivers to a new version or reinstalling the current driver Windows XP may identify the BarcoMed Display Controllers [...]

System manual MeDis 5MP1HM 43 Inst alling the BarcoMed 5MP2 AURA, 5MP2, 5MP1HM, 5MP1H or 4MP2 Windows XP Software SPECIAL NOTE: Prior to installing the BarcoMed drivers you MUST install the BarcoMed Display Controller(s), connect the high resolution display(s) to the controller(s), and turn the high resolution display(s) on. Refer to the Hardware I[...]

System manual MeDis 5MP1HM 44 7. Insert your BarcoMed Software CD into your computer s CD drive. The BarcoMed Product Inst allation W izard should start automatically . If it doesnt start within 5 minutes, browse the contents of your BarcoMed Software CD and double click on the file: Setup.exe to start the wizard. 8. The BarcoMed [...]

System manual MeDis 5MP1HM 45 Note: Y ou can install the driver for only one type of BarcoMed device at a time. If you have multiple types of BarcoMed devices installed in your computer , you will need to rerun the installer to install the drivers for the other devices. 1 1. If you selected a device with an existing driver , the wizard will compare[...]

System manual MeDis 5MP1HM 46 Figure 19: 5MP2 AURADualView Enabled Figure 20: 5MP2 AURADualView Disabled BarcoMed driver and sof tware installation[...]

System manual MeDis 5MP1HM 47 If DualView is not enabled, you will see a single virtual screen in the display properties dialog for both heads of a BarcoMed Display Controller . If DualView is enabled, you will see a two virtual screens in the dialog box on the Settings T ab of the Display Properties Control Panel, one for each head of the BarcoMed[...]

System manual MeDis 5MP1HM 48 Note: Clicking Cancel will also return you to the BarcoMed Product Inst all W izard, but will not delete the Barco Display Driver . The wizard will also begin to install the next selected piece of BarcoMed Software. If the Wizard failed to successfully install the selected driver , it will warn you (figure 22). C[...]

System manual MeDis 5MP1HM 49 Figure 23 20. The Setup T ype page will now appear (figure 24). Choose T ypical to install the default schemes with English names. Choose Custom to install the default schemes with either Dutch or German names. Currently the default schemes are not supported in the Japanese, Korean and Chinese languag[...]

System manual MeDis 5MP1HM 50 21. The Ready to Install Program page will now appear , click Install to install DPMS or Back if you wish to change any of your DPMS installation settings. During installation the wizard will display a progress screen. 22. When the InstallShield Wizard Completed page appears, click Finish [...]

System manual MeDis 5MP1HM 51 Setting the Resolution of Your 5MP1HM Once you have completed the installation of the display driver , you need to set the resolution for each display connected to each controller . 1. T o set the resolution for your high resolution display(s), right click on the desktop and select Properties . SPECIAL NOTE: If y[...]

System manual MeDis 5MP1HM 52 Repeat steps 2 - 7 for each aditional BarcoMed 5MP1HM display controlled installed in your system. If you are using a Quad-Head Configuration repeat all of the above steps for the two displays on the second display controller . Special note: After setting the resolutions in a Quad-Head Configuration you may need to dra[...]

System manual MeDis 5MP1HM 53 Reinstalling or Updating your BarcoMed 5MP2 AURA, 5MP2, 5MP1HM, 5MP1H or 4MP2 Drivers T o reinstall or update only the BarcoMed Driver , follow the steps described in the section Using the BarcoMed Product Installation Wizard found at the beginning of this chapter with the following changes. 1. Skip S tep 1. 2. I[...]

System manual MeDis 5MP1HM 54 (This page intentionally left blank.) BarcoMed driver and sof tware installation[...]

System manual MeDis 5MP1HM 55 BARCOMED CONTROLLER T OOLS[...]

System manual MeDis 5MP1HM 56 (This page intentionally left blank.) BarcoMed controller tools[...]

System manual MeDis 5MP1HM 57 BARCOMED DRIVER TAB Introduction After the BarcoMed Windows Display Controller Driver is installed, a new Display Properties tab is available for configuring special features of the BarcoMed Display Controller . Please note that you must have logged on to Windows using an account with administrator privileges in order [...]

System manual MeDis 5MP1HM 58 Figure 28: BarcoMed Driver T ab under Windows 2000 Figure 29: BarcoMed Driver T ab under Windows XP BarcoMed controller tools[...]

System manual MeDis 5MP1HM 59 St atus Displays the current BarcoMed Display Controller , driver, and the currently selected display resolution. Graphics Board This displays the current BarcoMed Display Controller . Driver Version This displays the current BarcoMed driver version. Resolution This displays the currently selected display resolution. P[...]

System manual MeDis 5MP1HM 60 index 10 to 245 contain the missing gray values so that the palette has the full 256 gray values within it. Please note that dithering is not permitted while in this mode. The Enable Dithering check box will be grayed-out, and dithering will be automatically disabled regardless of whether this check box is checked. Thi[...]

System manual MeDis 5MP1HM 61 application requires this Static Gray Palette with NO System colors mode, contact your application provider . Drawing Modes Y ou can choose one or both of the following Drawing Modes: Enable DirectDraw This option allows the user to enable or disable DirectDraw . DirectDraw is a software interface that provides d[...]

System manual MeDis 5MP1HM 62 one row option from the pull-down list. This would cause the Windows virtual desktop to be resized to fit on the three monitors, and you can move your cursor horizontally from one screen to the other . If Custom Configuration is displayed, it means that the current monitor configuration was set via the registr[...]

System manual MeDis 5MP1HM 63 BARCOMED HARDW ARE TAB Introduction The BarcoMed Hardware T ab is used for gathering information about BarcoMed Display Controller(s). For all BarcoMed Display Controller(s) it will display PCI information. In addition for BarcoMed Display Controller(s) based on the AURA video chipset it will also display information a[...]

System manual MeDis 5MP1HM 64 T o access the BarcoMed Hardware T ab do the following: 1. Open the Display Properties Control Panel by right clicking on the desktop, then select Properties. 2. Under Wi ndo ws NT 4.0, Click on the BarcoMed Hardware T ab (see figure 30, below). Under W indows 2000 and Windows XP , click on the Set[...]

System manual MeDis 5MP1HM 65 Figure 31: BarcoMed Hardware T ab under Windows 2000 and Windows XP Using The BarcoMed Hardware T ab Device Displays the current BarcoMed Display Controller , driver, and the currently selected display resolution. Identify Device: This button is for BarcoView Medical Imaging Systems (MIS) internal use only and is graye[...]

System manual MeDis 5MP1HM 66 PCI Information Device ID: Displays the devices PCI Device ID number . V endor ID: Displays the device manufacturer s PCI V endor ID number . Subsystem ID: Displays the devices PCI Subsystem ID number . SubsystemV endorID: Displays the devices PCI Subsystem Vendor ID number . VGA St atus: Displays whether t[...]

System manual MeDis 5MP1HM 67 update the firmware stored in the ROM of the currently selected BarcoMed Display Controller . The BarcoMed Hardware Configuration Wizard is a wizard style application that uses dialog boxes to guide the user through the flash update procedure. The user will be prompted to select a firmware update file to use for [...]

System manual MeDis 5MP1HM 68 (This page intentionally left blank.) BarcoMed controller tools[...]

System manual MeDis 5MP1HM 69 BARCO DPMS SCREEN SA VER OVERVIEW Introduction The BARCO DPMS (Display Power Management Signaling) Screen Saver allows the user to set power and display saving features for medical displays driven by BarcoMed Display Controllers. At the end of the work day , the display will enter certain DPMS states as requested by th[...]

System manual MeDis 5MP1HM 70 BARCO DPMS Screen Saver Options From the BARCO DPMS Screen Saver Control Panel you can change many DPMS screen saver elements simultaneously . The DPMS screen saver elements in each scheme are work schedule, work day screen saver, DPMS settings after work day , and many additional options. Current Scheme Lists th[...]

System manual MeDis 5MP1HM 71 Screen Saver During Work Day On CRT based displays, such as the Barco MGD series, a regular screen saver can be invoked during user inactivity during the work day . This regular screen saver and its settings can be chosen from the Screen Saver During Work Day section. We recommend using an all black s[...]

System manual MeDis 5MP1HM 72 e t a t S S M P D s g n i v a S r e w o P r o t i n o M e m i T y r e v o c e R n Oe n o NA / N y b - d n a t Sl a m i n i Mt r o h S d n e p s u Sl a i t n a t s b u Sr e g n o L f f Om u m i x a Mt s e g n o L Monitor Settings Select the amount of time the display requires to warm-up. Since all CRT based displays req[...]

System manual MeDis 5MP1HM 73 privileges. If a user who does not have administrator privileges tries to save a scheme using an existing default scheme name, an error message is displayed saying you must have administrator rights to modify a default scheme. If an administrator saves a scheme using an existing default scheme name, a message is [...]

System manual MeDis 5MP1HM 74 Figure 32: Windows NT 4.0 Screen Saver T ab BarcoMed controller tools[...]

System manual MeDis 5MP1HM 75 Figure 33: Windows 2000 Screen Saver T ab Figure 34: Windows XP Screen Saver T ab BarcoMed controller tools[...]

System manual MeDis 5MP1HM 76 3. Click on the Settings button. The BARCO DPMS Screen Saver Control Panel will open (see figure 35). Figure 35: BARCO DPMS Settings Control Panel 4. Use the default schemes by selecting one of the three default schemes. Click OK . Then Click OK again. Note: If you make any changes to any of the[...]

System manual MeDis 5MP1HM 77 Figure 36 T o create a new scheme by modifying one of the three default schemes please do the following. 1. Open the Display Properties Control Panel by right clicking on an empty space of the desktop and selecting Properties from the drop down menu; then select the Screen Saver tab. 2. Select the [...]

System manual MeDis 5MP1HM 78 10. Save your preferences by pressing the Save As button and entering a new profile name in the Save Profile Setting dialog box. 1 1. Apply your new scheme by clicking OK. 12. Click OK again to close the Display Properties Control Panel. Inst alling or Reinst alling BARCO DPMS T o install [...]

System manual MeDis 5MP1HM 79 3. Select the radio button next to Remove on the Program Maintenance screen of the Wizard and click Next (figure 38). Figure 38 4. Click Remove on the Remove Program Screen of the Wizard (figure 39). Figure 39 5. When the Wizard has finished removing the program, click Finish on the Inst allShie[...]

System manual MeDis 5MP1HM 80 Figure 40 6. Click Quit to exit the BarcoMed Product Inst allation W izard. BarcoMed controller tools[...]

System manual MeDis 5MP1HM 81 MEDICAL SOFTW ARE INST ALLA TION AND USAGE[...]

System manual MeDis 5MP1HM 82 (This page intentionally left blank.) MediCal software installation and usage[...]

System manual MeDis 5MP1HM 83 MEDICAL SOFTW ARE INST A L L A TION Install MediCal on the PC. Follow the instructions from the MediCal User Guide. Important: Do not forget you have to have Administrator privileges to install or uninstall MediCal. OPTICAL SENSOR CONNECTION If you are using an X-Rite DTP92 sensor for conformity calibration and consist[...]

System manual MeDis 5MP1HM 84 (This page intentionally left blank.) MediCal software installation and usage[...]

System manual MeDis 5MP1HM 85 DISPLA Y USER MANUAL[...]

System manual MeDis 5MP1HM 86 (This page intentionally left blank.) Display User Manual[...]

System manual MeDis 5MP1HM 87 © 2003 BARCO nv . All rights reserved. Trademark information TrueGrey , MediCal, BarcoMed, and MeDis are registered trademarks of BARCO NV . W indows NT is a registered trademark of Microsoft Corporation. Display User Manual[...]

System manual MeDis 5MP1HM 88 Regulations  This apparatus conforms to: IEC601-1, UL2601-1, cUL2601-1, EN 60601-1  This apparatus is classified as Type B without Applied Part. Usage in Hazardous locations  Class I equipment  Equipment not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitro[...]

System manual MeDis 5MP1HM 89 INTRODUCTION Overview Resolution and bandwidths The BARCO MGD 521 M and MGD 521 MKII displays are ultra-high resolution, grayscale portrait displays. Their outstanding visual performance, combining a 5 MegaPixel resolution with a very high brightness, makes them ideal for diagnostic imaging and many other medical and s[...]

System manual MeDis 5MP1HM 90 adjust and check BARCOs medical displays. A lot of adjustments can also be done on the monitor itself, by means of an extensive on-screen menu system, accessible from the rear panel controls. Power saving system The MGD 521 displays are equipped with a power saving system. When left idle for a certain time, the comp[...]

System manual MeDis 5MP1HM 91 About the manuals This guide is meant for people who want to install and use the MGD 521 displays, as well as people who need to install and adjust the displays. Chapter 4, Adjustments, is meant for this second category only , because it describes actions and procedures that require a technical skill to be performed pr[...]

System manual MeDis 5MP1HM 92 INST ALLA TION Precautions  Keep your original packaging. It is designed for this display and is the ideal protection during transport.  Do not lift the display all by yourself to avoid injury .  Avoid reflections in the picture tube to reduce eye strain.  Place the display on a strong and stable table or d[...]

System manual MeDis 5MP1HM 93 Controls and connectors 1 REMOTE OUT REMOTE IN VIDEO HS / CS VS 2 4 5 6 7 8 9 10 11 3 {1} Optical sensor plug {2} Ambient Light Compensation (ALC) sensor (optional) {3} Green power LED {4} Control knob, combination of a push button and a turning knob. The control knob is used for switching the power on/off, and selecti[...]

System manual MeDis 5MP1HM 94 Signal connection a) Connection of video signals The connected equipment must comply to all relevant safety demands. Important: The use of low-quality video cables can distort the video signal and influence diagnosis. 1. Check the impedance of the imaging board that produces the video signals you want to connect. It mu[...]

System manual MeDis 5MP1HM 95 b) Connection of data signals The display can be controlled remotely by a computer through the serial data bus. A typical example of this, is the MediCal software that controls the display . MediCal runs on a PC that is connected through the serial data bus. This PC is not necessarily the same computer as the one that [...]

System manual MeDis 5MP1HM 96 d) Connection of power 1. Power cord: Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 A WG min., rated 300 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application. 2. Plug one end of the power cord into the rear of the display[...]

System manual MeDis 5MP1HM 97 Import ant considerations  The best environment for diagnostic imaging is one with controlled and dimmed ambient light. The human eye's sensitivity depends on the ambient light strength. It is most sensitive to small contrast changes (or subtle image details) at limited ambient light levels.  The best ambien[...]

System manual MeDis 5MP1HM 98 OPERA TION: USER CONTROLS Important : The best way to adjust and control the display is by using MediCal, which displays the ideal test patterns for correct adjustment. However, in case you do not dispose of MediCal, you can control and adjust the display by means of the built-in On-Screen Display (OSD). Switching on /[...]

System manual MeDis 5MP1HM 99 Contrast and brightness control Contrast and brightness can be controlled through the OSD menus. To activate the OSD Turn the control knob {4} from left to right or from right to left. As a result, the OSD main menu appears. Note: The control knob should turn over at least 30 degrees before the OSD becomes visible. Con[...]

System manual MeDis 5MP1HM 100 To control contrast manually 1 Turn the control knob to select Contrast in the OSD main menu. 2 Press the control knob shortly . The contrast control menu appears. 3 In the contrast control menu, select Manual contrast adjustment and press the control knob shortly . The contrast scroll bar appears. 4 Turn the control [...]

System manual MeDis 5MP1HM 101 STATUS INFORMATION Display Name: MGD 521MKII Serial Number: 5114147 Mode Name: New mode Mode H-frequency: 175.32 kHz Mode V-frequency: 79.94 Hz Software Version: V 1.01 Run time: 50 hours White level: 300 cd/m2 Activity timeout 30s SH compensation OFF Actual H-frequency:125.30kHz Actual V-frequency: 80.00 Hz - Exit Ex[...]

System manual MeDis 5MP1HM 102 Software V ersion: The internal software version. Run time: The total operating time since production, including burn-in time. White level: The displays white level or light output after calibration, in calibrated position. Activity timeout : This is the time, expressed in seconds, before the display interrupts the[...]

System manual MeDis 5MP1HM 103 AD V ANCED SETTINGS AN D ADJUSTMENTS (FOR SERVICE ST AFF ONL Y) Important: The functions and controls described in this chapter can have a serious impact on the performance of the display . They should be touched by trained service staff only! Settings SETTINGS INFORMATION - LUC OFF - ALC OFF - Orbiter OFF - Power sav[...]

System manual MeDis 5MP1HM 104 Explanation of the Settings menu items LUC: LUC is short for Luminance Uniformity Control. When switched on, the internal waveform processor will modulate the gain of the video amplifier so that the luminance is equal all over the screen (within a tolerance of +/- 5%). The LUC system can be calibrated in the Adjustmen[...]

System manual MeDis 5MP1HM 105 ADJUSTMENTS - Geometry - Focus - ALC - Luminance uniformity - Factory reset - Exit Adjustments menu Adjustment s a) How to make the adjustments 1 Turn the control knob at the rear from left to right or from right to left to activate the On-Screen Display (OSD) main menu. 2 In the main menu, turn the control knob to se[...]

System manual MeDis 5MP1HM 106 Width Horizontal position Height Vertical position Blanking - Blanking left Blanking - Blanking right Blanking - Blanking top Display User Manual[...]

System manual MeDis 5MP1HM 107 Interlacing - Pre correction In most cases you do not need to change this adjustment. Y ou may need to increase this adjustment only when the connected video and sync signal contains an abnormally big number of equalization pulses before the vertical sync (more than 8 lines), resulting in a phase error (geometry disto[...]

System manual MeDis 5MP1HM 108 SH Compensation: SH Position With SH Compensation on, we advise to use the SH Position control instead of the Horizontal Position control in the Geometry menu. Advanced geometry - Horizontal skewing Advanced geometry - Horizontal bowing Advanced geometry - Horizontal trapezium Advanced geometry - Horizontal parabola A[...]

System manual MeDis 5MP1HM 109 Advanced geometry - Corner top right Advanced geometry - Corner bottom left Advanced geometry - Corner bottom right Advanced geometry - Linearity & S-correction - Horizontal linearity Advanced geometry - Linearity & S-correction - Horizontal S-corr Advanced geometry - Linearity & S-correction - Vertical li[...]

System manual MeDis 5MP1HM 110 Advanced geometry - Advanced bowing & skewing - Horizontal bowing left Advanced geometry - Advanced bowing & skewing - Horizontal bowing right Advanced geometry - Advanced bowing & skewing - Horizontal skewing left Advanced geometry - Advanced bowing & skewing - Horizontal skewing right Advanced geomet[...]

System manual MeDis 5MP1HM 111 Focus Static focus Adjust St atic focus to obtain an image as sharp as possible in the center . Focus zone Y ou can adjust the focus in 25 independent zones. Turn the control knob to obtain an image as sharp as possible in the selected zone. Press the control knob to switch to the next zone. ALC (optional) Ambient Lig[...]

System manual MeDis 5MP1HM 112 Luminance uniformity This menu allows you to calibrate the display , including the Luminance Uniformity circuit. Proceed as follows: 1 Connect the X-Rite DTP92 sensor and apply the black shield (see chapter "Installation"). 2 Follow the instructions on the screen. Factory reset This function allows you to un[...]

System manual MeDis 5MP1HM 113 MAINTENANCE Picture tube The glass panel of the picture tube is handled with a special coating. T ake care not to damage or scratch the coating. Clean the picture tube with a soft woolen or cotton cloth. The cloth should be moist, not wet! Use a watery solution or a mild commercial glass cleaning solution. Apply (e.g.[...]

System manual MeDis 5MP1HM 114 TROUBLESHOOTING There appears no image on the picture tube, the green LED at the front is out  Check if the power cord is properly connected to the power outlet and to the display .  Check if the power button is switched on. There appears no image, the green LED is on The display is switched in S tand-by , manua[...]

System manual MeDis 5MP1HM 115 APPENDIX A : BACKGROUND INFORMA TION Luminance Uniformity Correction A characteristic (or limitation) of every picture tube (CRT) is that the luminance decreases towards the edge of the screen surface. The decrease is normally 20 to 30 %. This is caused by the shape of the picture tube. Inside the CRT , a so- called e[...]

System manual MeDis 5MP1HM 116 At last, the imaging board delivers no sync signals at all, and the micro-controller switches off all but one power supplies in the display . Only the micro-controller's own supply keeps on running, resulting in a very low power consumption of 5 W . If you start using the computer again, the imaging board switche[...]

System manual MeDis 5MP1HM 117 Picture tube: Faceplate transmission: 32% Faceplate type: ARC panel Image representation: portrait Phosphor: P45 (standard ) or P104 (option for MGD 521 MKII only) Light output: (P45 phosphor) MGD 521: Calibrated: 300 Cd/m2 MGD 521M: Calibrated: 400 Cd/m2 Peak: 600 Cd/m2 Resolution: Max. adress. pixels: 2048 Max. adre[...]