Billion Electric Company 7100S manuale d’uso

BIPAC 7100S ADSL Modem/Router with 10/100M LAN Port User Manual[...]

[...]

i Table of Contents Chapter 1 ........................................................................................................... 1 Introduction ........................................................................................................................... 1 1.1 An Overview of BIPAC 7100S ........................................[...]

Billion BIPAC 7100S ADSL Modem/Router ii 3.4.3.4.5 URL Blocking .......................................................................................... 36 3.4.3.5 VPN (Virtual Private Networks) ..................................................................... 37 3.4.3.6 Virtual Server .........................................................[...]

1 Chapter 1 Introduction 1.1 An Overview of BIPAC 7100S BIPAC 7100S ADSL Modem/Router provides a high -spee d Ethernet port for high-speed Internet browsing. It can support downstream transmission rate s of up to 8Mbps a nd upstream transmission rate s of up to 1024Kbps. It is compliant with Multi-Mo de standard (ANSI T1.413, Issue 2; G.dmt (G.992.[...]

Billion BIPAC 7100S ADSL Modem/Router 2 1.2 Package Contents 1. Billion BIPAC 7100S ADSL Modem/Router 2. One CD-ROM containing the driver and online ma nual 3. One Quick Start Guide 4. One RJ-11 ADSL/telephone cable 5. One CAT-5 straight LAN cable 6. One power adapter 1.3 BIPAC 7100S Features BIPAC 7100S ADSL Modem/Router provides the foll owing fe[...]

Chapter 1 Introduction 3 example, user can assign a PC in LAN acting as WEB server inside and expose it to th e outside network. Outside user can brow se inside web serv er directly while it is protected by NAT. A DMZ host setting is also provided to a local comput er exposed to the outside networ k, Internet.  Firewall: Supports SOHO firewall w[...]

4 Chapter 2 Using Billion ADSL Modem/Router 2.1 Cautions for Using Billion ADSL Modem/Router Do not place the router under high humidity and high temperat ure. Do not use the same power source for the dev ice with other equipment. Do not open or repair the cas e yourself. If the device is too hot, turn off the power immediately and have a qualified[...]

Chapter 2 Using the ADSL Modem/Router 5 2.3 The Rear Ports LINE (RJ-11 connector) Connect the supplied RJ-11 cable to this port when connecting to the ADSL Reset Press it to restore the factory default setting back LAN (RJ-45 connector) Connect the supplied crossover cable to this port when connecting to a NIC (Network Interface card ) in PC. Conne[...]

Billion BIPAC 7100S ADSL Modem/Router 6 So long as the cables a re connected and the LE Ds are lit normally, follow sectio n “3.2 Configuring the Network Properties” below to modify the network settings. Since the product cannot auto-detec t whether your cable is correct or not, please make sure you are using the right cable to a PC or a Hub.[...]

7 Chapter 3 Configuration BIPAC 7100S can be configured with your We b browse r. The web browse r is included as a stand ard application in following op eration systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000 /Me/XP, etc. The product provides a very easy and u s er-friendly in terface for co nfiguration. 3.1 Before Configuration This section de[...]

Billion BIPAC 7100S ADSL Modem/Router 8 3. In the Local Area Connection Status window , click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Chapter 3 Configuration 9 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and Dial-up Connections . 2. Double-click Local [...]

Billion BIPAC 7100S ADSL Modem/Router 10 3. In the Local Area Connection Status window , click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties .[...]

Chapter 3 Configuration 11 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 95/98/ME 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and choose the Configuration tab. 2. Select[...]

Billion BIPAC 7100S ADSL Modem/Router 12 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click OK to finish the configuration.[...]

Chapter 3 Configuration 13 Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double- click on Net work and choose the Protocols tab. 2. Select TCP/IP Protocol and cli ck Properties .[...]

Billion BIPAC 7100S ADSL Modem/Router 14 3. Select the Obtain an IP address from a DHCP server radio button and click OK . 3.2 Factory Default Settings Before you configure this device, you n eed to know the followi ng default settings. 1. Web Configuration Password: There are two leve ls of password protection, Administrator Level and User Lev el [...]

Chapter 3 Configuration 15 3.2.1 Password The default username and password are admin and password respectively. If you ever forget the pass word to log in, you may press the RESET button up to 2 seconds to restore th e fa ctory default settings. 3.2.2 LAN and WAN Port Addresses The parameters of LAN and WAN port s are pre-set in the factory. The d[...]

Billion BIPAC 7100S ADSL Modem/Router 16 IPoA VPI/VCI, VC-based/LLC-based multip lexing, IP address, Subnet mask, Gateway address, and Domain Name S ystem (DNS) IP address (it is fixed IP address). 3.4 Configuring with Web Browser The ADSL Modem/Router can be configured with your Web browser. The web bro wser is included as a standard application i[...]

Chapter 3 Configuration 17 At the configuration homepage, the l eft navigation p ane where bo okmarks are provid ed links you directly to the desired setup page, including:  Quick Start  Configuration (LAN, WAN, Firewall, System, VPN, Virtual Server, Advanced and Help )  Status (System Status, Device Info, System Logs, Secu rity Logs, ARP [...]

Billion BIPAC 7100S ADSL Modem/Router 18 3.4.1.1 Status – ADSL Status Displays the status of your ADSL conn ection. It will refresh every two seconds. 3.4.1.1.1 ADSL Status – WAN Status[...]

Chapter 3 Configuration 19 3.4.1.1.2 ADSL Status – ATM Status 3.4.1.2 Status – LAN Status Displays the status of your Local Area Network (LAN) conne ction.[...]

Billion BIPAC 7100S ADSL Modem/Router 20 3.4.1.2.1 LAN Status – TCP Status 3.4.1.3 Status- PPP Status Displays the status of your PPP connect ion. It will refresh every ten seconds.[...]

Chapter 3 Configuration 21 3.4.1.4 Status- Learned MAC Table Aging Timeout: Enter the time period for the route r to memori ze MAC addresse s. 3.4.1.5 Routing Table Display the current routing paths of BIPAC 7100S.[...]

Billion BIPAC 7100S ADSL Modem/Router 22 3.4.1.6 System Log Display the system logs cumulated t ill the present time. You can trace t he historical information through this function. 3.4.1.7 Security Logs Display the information of security logs. If hacker attacks your sever, he will be isolated by the firewall function and the router w ill record [...]

Chapter 3 Configuration 23 3.4.2 Quick Start If you use this device to access the Internet throu gh the ISP, this w eb page is enough for you to config ure this router and access the Internet without a problem. Please check Chapter 3.3 ( Information from the ISP) , then enter the proper values into this web page, click the Apply button and then cli[...]

Billion BIPAC 7100S ADSL Modem/Router 24 Select the item of PVCs you want to configure. Then, press the Submit button.[...]

Chapter 3 Configuration 25 Virtual Circuit Virtual Circuit: Enable/Disable the settings of this VC. Bridge: If you set this device to be bridge mode, select Enable; if not, please select Di sabl e. IGMP: You can Enable or Disable this function. Encapsulation: There are eleven ways ─ PPPoE VC-Mux, PPPoE LLC, PPPoE None, PPPoA VC-Mux, PPPoA LLC, 14[...]

Billion BIPAC 7100S ADSL Modem/Router 26 VCI: Consult the telephone company to get the Virtua l Channel Identifier (VCI) number. The default value is 32. Service Category: Select UBR or CBR . DHCP Client DHCP Client: Check to enable the DHCP client function if you want the device to get an IP address automatically from your ISP. Host Name: Enter th[...]

Chapter 3 Configuration 27 Automatic Reconnect: Check to enable this device to autom atically re-establish the PPPoE session when disconnected by ISP. 3.4.3.2 LAN This screen contains settings for LAN interfa ce attached to the LAN port. Device IP Address IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan t[...]

Billion BIPAC 7100S ADSL Modem/Router 28 With this case, the DHCP pool is from 192.168.1.100 to 192.168.1.199. Th erefore, the local computer will get an IP address located at this ran ge rando mly. Lease Time: Set the lease time you required. User Mode: There are two selections, Single User and Multi-User, for this setting. 3.4.3.3 System There ar[...]

Chapter 3 Configuration 29 3.4.3.3.2 Time Zone BIPAC 7100S does not have a real tim e clock on board; in stead, it uses the simple net work time protocol (SNTP) to get the current time from the SNTP server in outside n etwork. Please choose your local time zone and click Submit. Yo u will get the correct time in formatio n after you really establis[...]

Billion BIPAC 7100S ADSL Modem/Router 30 3.4.3.3.3 Upgrade To upgrade the firmware of BIPAC 7100S, you should do wnload or copy the firmwa re to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgra ding. When the procedure is completed , BIPAC 7100S will re[...]

Chapter 3 Configuration 31 3.4.3.3.5 Restart In case the router stops responding corre ctly or in some other way stops fun ctioning, you can perform the restart. Your setting won’t be changed. Performi ng the restart, click on the Submit button.[...]

Billion BIPAC 7100S ADSL Modem/Router 32 3.4.3.4 Firewall User can decide to enable this firewall function incl uding Packet Filter, Block Ha cker Attack, and Block WAN request features for better security control or not. But be noted, it wa stes net work processor computation power. The performance will be lower about 10% to 15%. More firewall fea[...]

Chapter 3 Configuration 33  Outgoing  Incoming: Determine whether the rule is for o utg oing packets or for incomin g packets. Active: Choose “Ye s” to enable the rule, or choose “No ” to disa bl e the rule. Packet Type: Specify the packet type (TCP, UDP, ICMP or any) that the rule will be applied to. Select TCP if you want to scope f[...]

Billion BIPAC 7100S ADSL Modem/Router 34 3.4.3.4.2 Bridge Filtering Enable Bridge Filtering: Check Yes to enable this functio n or check No to disable. Src MAC: Enter the source MAC addre ss. Dest MAC: Enter the destination MAC address. Typ e: Enter the Ethernet type.  Block  For ward: Check Block if you want to block requests fr om the sourc[...]

Chapter 3 Configuration 35 - Snork Attack - UDP port loop-back - TCP NULL scan 3.4.3.4.4 Block WAN Request Check “Enable” if you want to exclude outside PING request from reaching on this router.[...]

Billion BIPAC 7100S ADSL Modem/Router 36 3.4.3.4.5 URL Blocking URL blocking function ena bles you to avoid your LA N PCs from accessing some URLs. You must check the “Enable” radio button to make the following figure appear for fu rther configuration. Always Block : Check this will block all browsing requests from PCs Block: to specify the tim[...]

Chapter 3 Configuration 37 3.4.3.5 VPN (Virtual Private Networks) we will introduce the VPN settings to establish a se cure communication path with remote site based on IPsec. Please check “Enable” and click “Add” button . Then you will see IKE Setup page as below figure. Then, you can configure the rule as your security plan. Active : To e[...]

Billion BIPAC 7100S ADSL Modem/Router 38 Remote Subnet Mask: The range of re mote IPs can be communicat ed. For exa mple, it is 25 5.255.255.0. Proposal: There are two methods to check the authentic ation informatio n, AH (authentication header) and ESP (Encapsulating Security Payload). ESP: Data will be encrypted and/or authentic. DE S and 3DES en[...]

Chapter 3 Configuration 39 3.4.3.6 Virtual Server Being a natural Internet firewall, the ADSL Router pr otects your ne twork from being accessed by out side users. When it needs to allow out side users to access internal servers, e.g. Web server, FTP server, E- mail server or News serve r, this product can act as a virtual server. You can set up a [...]

Billion BIPAC 7100S ADSL Modem/Router 40 Port Type: Select TCP if you want to scope for the connectio n-based application service on the remote server using the port num ber. Or select UDP if you want to scope for the connectionles s application service on the remote server u sing the port number. Host IP Address: Enter the IP address of certai n i[...]

Chapter 3 Configuration 41 You can obtain Domain Name System (DNS) IP address automatic ally if ISP provides it whe n you logon. Or your ISP may provide you with an IP address of DNS. If this i s the case, you must enter the DNS I P address. 3.4.3.7.3 Dynamic DNS With Dynamic DNS service, a domain name can be trans lated int o a dynamic IP address,[...]

Billion BIPAC 7100S ADSL Modem/Router 42 Check the “Enable” button to access the Dynamic DNS servi ce. You may si gn up Dynamic DNS service at http://www.dyndns.org T and there you can al so register domain names. Host: Enter one domain na me you have registered. User Name: Enter the usernam e used for si gn-up. Password: Enter the password use[...]

Chapter 3 Configuration 43 User’s IP: Allows the user to assign the IP address to map the co rresponding NAT/NAPT sessions. Session Name status will be displayed at the middle of this page to show t he corresponding Session Name with its IP address. Click Session Name Configuration, the following screen displays. Session Name: Enter the desired s[...]

Billion BIPAC 7100S ADSL Modem/Router 44 3.4.3.7.5 RIP RIP: Default is Disabled . Border Gateway: Default is Enabled . Supply Interval  seconds: The default value is 30 second s. Expire Timeout  seconds: The def ault value is 1 80 seconds. Garbage Timeout  seconds: The default value is 120 second s.[...]

Chapter 3 Configuration 45 3.4.3.7.6 SNMP Simple Network Management Protocol (SNMP) is an optional fea ture that may or may not be supported by your ADSL Bridge/Router. SNMP is an application layer protocol that is used for managing networks. SNMP is an optional feature that may or may not be in the specific firmware t hat you are working with. The[...]

Billion BIPAC 7100S ADSL Modem/Router 46 3.4.3.7.7 Static Routing If you have another router with a LAN-to-LAN conne cti on, you may create a static routing on the router that is the gateway to Internet. Add: Click this button to add a new static routing. When you click this button, the next figure appears. Delete: Check the item you want to delete[...]

Chapter 3 Configuration 47 3.4.3.7.8 MISC Configuration HTTP server access: Def ault at Res tricted . HTTP server port: Default at 80 . FTP server: Default at Enabled . TFTP server: Default at Disabled . DMZ: Regarding the DMZ Host, it is a local computer expo sed to the Internet. Therefore, an incoming packet will be checked by NAT algorithms in t[...]

Billion BIPAC 7100S ADSL Modem/Router 48 Checking LAN Connectio n Testing Ethernet LAN connec tion This test passes if the Ethernet LA N interface is working p ro perly. Checking ADSL Connection Testing ADSL Synchronization This test checks your DSL modem to see if it c an successfully ne gotiate and establish a DSL connection with your service pro[...]

Chapter 3 Configuration 49 Test ATM OAM End-to-End Loop Ba c k This test sends ATM OAM F5 End-to-End loop bac k re quest cells to the central office equipment s through your DSL connection. This test returns PASS if response cell is rece ived. Since your service provider might not support this test, your DSL modem could still work even if this test[...]

3.4.4 Save Config Click the Submit button to write settings to flash. Then, the system will reboot for change s to take effe ct. 50[...]

51 Chapter 4 Troubleshooting If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADSL Router Problem Corrective Action None[...]

52 APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s M anual . If you cannot resolve the problem with the Troubles hooting chapter, please contact the deale r where you purchased this product. Contact Billion AUSTRALIA http://www.billion.com.au/ ©2004 Billion El[...]