Bryant 362AAN manuale d’uso

NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS ..................................................1-2 Minimum Clearance to Combustibles ......................................2 INTRODUCTION ............................................[...]

Only the latest issues of above codes should be used, and are available from either The National Fire Protection Agency, Bat- terymarch Park, Quincy, MA 02269 or The Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario M9W 1R3 Recognize safety information. This is the safety-alert symbol . When you see this symbol on the furnace and [...]

3. Caulking or sealants are applied to areas such as joints around window and door frames; between sole plates and floors; between wall-ceiling joints; between wall panels; at penetrations for plumbing, electrical, and fuel lines; and at other openings. If combustion and ventilation air must be supplied to an uncon- fined space from outside, an ope[...]

VENTING INSTRUCTIONS Venting of furnace should be to the outside and in accordance with local codes or requirements of local utility. OIL-FIRED APPLIANCES SHALL BE CONNECTED TO FLUES HAVING SUFFICIENT DRAFT AT ALL TIMES TO ENSURE SAFE AND PROPER OPERATION OF APPLIANCE. For additional venting information, refer to ANSI/NFPA 211 Chimney, Fireplaces, [...]

ELECTRICAL The appliance must be installed in accordance with current ANSI/NFPA 70 National Electrical Code, CSA C22.1 Canadian Electrical Code Part 1, and/or local codes. The control system depends on correct polarity of power supply. Connect HOT wire (H) and NEUTRAL wire (N) as shown in Fig. 7. A separate line voltage supply MUST be used with a f[...]

c. Tighten purge fitting. Allow oil to run to nozzle and fire burner. d. If purging takes longer than 30 sec and no flame has been established, burner stops. Push reset button on top of primary control to restart burner. e. For detailed information on operation of primary control, refer to instructions included with furnace. III. FAN ADJUSTMENT CHE[...]

The procedure for nozzle installation and/or replacement is out- lined in oil burner instruction manual which came with furnace. For ease of maintenance, the oiling procedure for burner motor, as outlined in burner manual, should be performed at this time. After replacement of nozzle, burner should be adjusted in accor- dance with Combustion Check [...]

17. Use a stiff brush and vacuum cleaner to clean inside of primary drum. CAUTION: Never use incendiary type cleaners (smoke sticks) for cleaning! WARNING: For all heat exchanger plates that have been removed, the gaskets MUST be replaced. Failure to replace gaskets could lead to heat exchanger leakage, sooting, and a hazardous condition which coul[...]

INSULATION INTERMEDIATE PANEL FILTER B A G D ELECTRICAL CONNECTIONS OIL INLET F 12 1 ⁄ 16 ″ EH 1 ″ INSULATION PARTITION PANEL SUPPLY DUCT CLEAN-OUT PORTS RETURN DUCT 1 ″ 3 ″ C A96309 DIMENSIONS (IN.) UNIT SIZE UNIT DIMENSIONS DUCT SUPPLY OPENING FLUE DIAMETER RETURN DUCT Width Depth Height AB C D E F G H 036105 22 52 [...]

Fig. 6—Barometric Damper Locations A95117 FIG. A FIG. G FIG. D FIG. L FIG. B FIG. C FIG. J FIG. H FIG. K POOR WRONG WRONG WRONG WRONG WRONG BAROMETRIC DAMPER LOCATIONS GOOD LOCATIONS BAD LOCATIONS —10—[...]

→ Fig. 7—Wiring Diagram A96380 INDOOR BLOWER MOTOR BR BR CAP T GND LINE V 24 V LINE V 24 V BK BL BR GR OR RD RD/BK VI WH YL F T CAP AL L GND BLACK BLUE BROWN GREEN ORANGE RED RED/BLACK STRIPE VIOLET WHITE YELLOW LOW SPEED FAN SWITCH TRANSFORMER START[...]

USER’S INFORMATION I. HERE’S HOW YOUR HEATING SYSTEM WORKS The furnace operates automatically. It is controlled by a thermostat which you set at the temperature most comfortable to you. When the inside temperature drops below this setting, your thermostat will turn on heating system. When thermostat calls for heat, power from transformer energi[...]