Bush Hog EFM 60 manuale d’uso

BU S H H O G ® ASSEMBL Y ● OPERA TION ● MAINTENANCE 300 $4.00 50024642 EFM 480/600 Economy F inishing Mower Operator ’s Manual[...]

CONGRA TULA TIONS! Y ou have invested in the best implement of its type on the market today . The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as wel[...]

EFM 480/600 Operator ’ s Manual T ABLE OF CONTENTS SECTION/P ARA P AGE W arranty . . . . . . . . . . . . . . . . . . . . . . . . . .2 Dealer Preparation Check List . . . . . . . . .3 Safety Precautions . . . . . . . . . . . . . . . . . .4 Federal Laws and Regulations . . . . . . . . .6 I INTRODUCTION AND DESCRIPTION . .7 1-1 Introduction . . . . [...]

BUSH HOG ® LIMITED W ARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-[...]

DEALER PREP ARA TION CHECK LIST EFM 480/600 Finishing Mowers BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator ’s Manual as a guide. ❒ 1. Assembled completed. ❒ 2. Gearboxes filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in good condition. ❒ 5. All fasteners torque[...]

Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safe- ty pre[...]

IMPORT ANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in death or serious bodily injury. In addition to the de[...]

IMPORT ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-St[...]

1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your EFM Series Rotary Cutter has been carefully designed to give maximum service with minimum down time.This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition. Please read this manual tho[...]

2-1 A TT ACHING TO TRACTOR A. Attach to tractor Cat. I three point hitch as described in tractor operator’s manual. B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor leaving cutter in position of shortest distance. SECURELY BLOCK CUTTER IN POSITION. C. P[...]

G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-3 H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of driveline sections and clean away all chips and filings. (Figure 2-5) K. Apply multi-pur[...]

SECTION III OPERA TING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- ate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety mes- sages shown on the caution, warning and d[...]

SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks. All bolts should be torqued as indicated in torque chart un[...]

4-3 BEL T ADJUSTMENT Belt tensions should be checked every 40 hours to get maximum life from drive belts and best perfor- mance from the cutter. Belt tension is adjusted by increasing or decreasing the length of the spring on the moveable idler. For proper belt tension on the mower, the spring lengths should be set at 2-7/8”. (Figure 4-1 C) To ad[...]

4-6 TROUBLESHOOTING Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num- ber, serial number, purchase date and exact cause or description of problem. Table 4-1 Troubleshooting PROBLEM PROB[...]

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equip- ment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lift[...]

E. Fasten mast supports and upper flex link to mast halves using 1/2 x 5” capscrew, pivot tube and locknut.. F. Place two long spacers on the caster stems and insert into caster arms. Place two long spacers and two short spacers on the caster stem above the caster arms. This arrangement will give a cutting height of approximately three inches. Se[...]

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more inform[...]

T ORQUE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15)[...]

BUSH HOG , L .L .C. ® P .O. Box 1039 ● Selma, AL 36702-1039 T elephone (334) 874-2700[...]