Bush Hog MP5 manuale d’uso

BU S H H O G ® ASSEMBL Y ● OPERA TION ● MAINTENANCE 798 $4.00 50018726 MP 5/ MP 6 MULCH PRO Operator ’s Manual[...]

CONGRA TULA TIONS! Y ou hav e inv ested in the best implement of its type on the market toda y . The care you giv e your Bush Hog implement will g reatly deter mine your satisf action with its perf or mance and its ser vice life . We urge a careful study of this manual to pro vide you with a thorough understanding of y our new implement bef ore ope[...]

MP 5/6 Operator’ s Manual T ABLE OF CONTENTS SECTION/P ARA P A GE W arranty ....................................................3 Dealer Preparation Chec k List ..................4 Saf ety Precautions ....................................5 F ederal Laws and Regulations ..................6 I INTRODUCTION AND DESCRIPTION ......7 1-1 Introduction ...[...]

BUSH HOG ® LIMITED W ARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-[...]

DEALER PREP ARA TION CHECK LIST MP 5/6 Finishing Mower s BEFORE DELIVERING MA CHINE — The follo wing check list should be completed. Use the Operator’ s Man ual as a guide. ❒ 1. Assembled completed. ❒ 2. Gearbo xes filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in good condition. ❒ 5. All f asteners torqu[...]

IMPOR T ANT SAFETY PRECA UTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury. In addition to the design an[...]

IMPOR T ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLO YERS, EMPLO YEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams[...]

1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your MP Series Rotary Cutter has been care- fully designed to give maximum service with mini- mum down time.This manual is provided to give you the necessary operating and maintenance instruc- tions for keeping your rotary cutter in top operating condition. Please read this manua[...]

2-1 A TT A CHING T O TRA CT OR A. Attach to tractor Cat. I three point hitch as described in tractor operator’s manual. B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor leaving cutter in position of shortest distance. SECURELY BLOCK CUTTER IN POSITION. [...]

G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-3 H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of driveline sections and clean away all chips and filings. (Figure 2-5) K. Apply multi-pur[...]

SECTION III OPERA TING INSTR UCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- ate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety mes- sages shown on the caution, warning and [...]

TIPS ON MO WING WITH A MULCHER The Bush Hog MP 5/6 is a finishing mow er with counter rotating blade sets designed to do a superior job of mulching grass clippings . T o get the maximum eff ectiveness from y our MP the tips listed below should be f ollow ed: ● Mow often - In gener al, mulching operations require more frequent mowing than w ould c[...]

SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks. All bolts should be torqued as indicated in torque chart un[...]

4-3 BEL T ADJUSTMENT Belt tensions should be checked every 40 hours to get maximum life from drive belts and best perfor- mance from the cutter. Belt tension is adjusted by increasing or decreasing the length of the spring on the moveable idlers. For proper belt tension on the mower, the spring lengths should be set at 2-7/8”. (Figure 4-2) To adj[...]

4-5 BLADE REPLA CEMENT Always replace all (4) blades on an assembly to retain balance. In addition to replacing blades when they become worn and dull, they should also be replaced if the uplift angle on the trailing side of the blade becomes worn off. As the angle wears down, the mulching action deteriorates. A. Raise cutter using tractor hydraulic[...]

4-6 BLADE SPINDLE SER VICE (Figure 4-5) If shaft bearings or other parts require replacement, proceed as follows: NOTE It is recommended that a Bush Hog dealer or other qualified person service the blade spindle. If blade spindles must be disassembled, special Bush Hog spanner wrenches are supplied for this operation. The Sheave Wrench is used on t[...]

TORQUE WRENCH CHART When using a torque wrench in conjunction with a Bush Hog shaft or sheave wrench, the following chart must be used to achieve the correct torque of 200 ft./lbs. Torque Wrench 12” 14” 16” 18” 20” 22” Length (A) Torque Indicator 133 140 145 150 154 157 Must Show ft./lbs. ft./lbs. ft./lbs. ft./lbs. ft./lbs. ft./lbs. 4-7[...]

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equip- ment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lift[...]

E. Fasten mast supports and upper flex link to mast halves using 1/2 x 5” bolt,pivot tube and locknut. F. Place one long spacer on the caster stems and insert into caster arms. Place three long spacers and two short spacers on the caster stem above the caster arms. this arrangement will give a cutting height of approximately 1-3/4” . Secure wit[...]

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more inform[...]

T ORQ UE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15[...]

P.O. Box 1039 l l Selma, AL 36702-1039 Telephone (334) 874-2700 l l www.bushhog.c om[...]