Vai alla pagina of
Manuali d’uso simili
-
Garage Door Opener
Chamberlain ATS 2113X
32 pagine 1.36 mb -
Garage Door Opener
Chamberlain 373LMC
2 pagine 0.35 mb -
Garage Door Opener
Chamberlain 2C507-2
2 pagine 0.08 mb -
Garage Door Opener
Chamberlain 450-6
10 pagine 1.37 mb -
Garage Door Opener
Chamberlain PD460-2K
40 pagine 1.86 mb -
Garage Door Opener
Chamberlain 374LMC
4 pagine 0.25 mb -
Garage Door Opener
Chamberlain 916LM
2 pagine 0.08 mb -
Garage Door Opener
Chamberlain 2500D
36 pagine 2.56 mb
Un buon manuale d’uso
Le regole impongono al rivenditore l'obbligo di fornire all'acquirente, insieme alle merci, il manuale d’uso Chamberlain 1345M. La mancanza del manuale d’uso o le informazioni errate fornite al consumatore sono la base di una denuncia in caso di inosservanza del dispositivo con il contratto. Secondo la legge, l’inclusione del manuale d’uso in una forma diversa da quella cartacea è permessa, che viene spesso utilizzato recentemente, includendo una forma grafica o elettronica Chamberlain 1345M o video didattici per gli utenti. La condizione è il suo carattere leggibile e comprensibile.
Che cosa è il manuale d’uso?
La parola deriva dal latino "instructio", cioè organizzare. Così, il manuale d’uso Chamberlain 1345M descrive le fasi del procedimento. Lo scopo del manuale d’uso è istruire, facilitare lo avviamento, l'uso di attrezzature o l’esecuzione di determinate azioni. Il manuale è una raccolta di informazioni sull'oggetto/servizio, un suggerimento.
Purtroppo, pochi utenti prendono il tempo di leggere il manuale d’uso, e un buono manuale non solo permette di conoscere una serie di funzionalità aggiuntive del dispositivo acquistato, ma anche evitare la maggioranza dei guasti.
Quindi cosa dovrebbe contenere il manuale perfetto?
Innanzitutto, il manuale d’uso Chamberlain 1345M dovrebbe contenere:
- informazioni sui dati tecnici del dispositivo Chamberlain 1345M
- nome del fabbricante e anno di fabbricazione Chamberlain 1345M
- istruzioni per l'uso, la regolazione e la manutenzione delle attrezzature Chamberlain 1345M
- segnaletica di sicurezza e certificati che confermano la conformità con le norme pertinenti
Perché non leggiamo i manuali d’uso?
Generalmente questo è dovuto alla mancanza di tempo e certezza per quanto riguarda la funzionalità specifica delle attrezzature acquistate. Purtroppo, la connessione e l’avvio Chamberlain 1345M non sono sufficienti. Questo manuale contiene una serie di linee guida per funzionalità specifiche, la sicurezza, metodi di manutenzione (anche i mezzi che dovrebbero essere usati), eventuali difetti Chamberlain 1345M e modi per risolvere i problemi più comuni durante l'uso. Infine, il manuale contiene le coordinate del servizio Chamberlain in assenza dell'efficacia delle soluzioni proposte. Attualmente, i manuali d’uso sotto forma di animazioni interessanti e video didattici che sono migliori che la brochure suscitano un interesse considerevole. Questo tipo di manuale permette all'utente di visualizzare tutto il video didattico senza saltare le specifiche e complicate descrizioni tecniche Chamberlain 1345M, come nel caso della versione cartacea.
Perché leggere il manuale d’uso?
Prima di tutto, contiene la risposta sulla struttura, le possibilità del dispositivo Chamberlain 1345M, l'uso di vari accessori ed una serie di informazioni per sfruttare totalmente tutte le caratteristiche e servizi.
Dopo l'acquisto di successo di attrezzature/dispositivo, prendere un momento per familiarizzare con tutte le parti del manuale d'uso Chamberlain 1345M. Attualmente, sono preparati con cura e tradotti per essere comprensibili non solo per gli utenti, ma per svolgere la loro funzione di base di informazioni e di aiuto.
Sommario del manuale d’uso
-
Pagina 1
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Model Series 1300 For Residential Use Only Owner’ s Manual ■ Please read this manual and the enc losed safety materials carefully! ■ Fasten the man ual near the garage door after installation. ■ The door WILL NO T CLOSE unless[...]
-
Pagina 2
2 When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully . When you see this Signal Word on the following [...]
-
Pagina 3
3 T o prevent damage to garage door and opener: • AL WA YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJURY OR DEA TH: • AL WA YS call a trained door systems technician if garage door binds, sticks, or is out of ba[...]
-
Pagina 4
4 Safety Re v ersing Sensor S u pport b racket & fastening hard w are is re qu ired. See page 17. — — — — — — — — Header W all FI N ISHED CEILI N G T orsion Spring Extension Spring OR Safety Re v ersing Sensor Gap b et w een floor and b ottom of door m u st not exceed 1/4" (6 mm) Access Door W all- mo u nted Door Control Ho[...]
-
Pagina 5
5 Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • The gap between the bottom of the garage door and the floor MUST NOT exceed 1/4" (6 mm). Otherwise, the safety reversal system may not work properly . • The floor or the garage door M[...]
-
Pagina 6
6 Straight Door Arm Section C u r v ed Door Arm Section Safety La b els and Literat u re Header Bracket U P C E IL I N G M O U N T O N L Y Sprocket Co v er 2-Cond u ctor Bell W ire W hite & W hite/Red Lighted Door Control B u tton w /6ABx1-1/2" scre w s Motor Unit w ith Light Lens Remote Control T ransmitter Visor Clip One-Piece Rail Styro[...]
-
Pagina 7
7 Hardwar e Inventor y Separate all hardware and group as shown below for the assembly and installation procedures. Nu t 5/16"-1 8 (4) Cle v is Pin 5/16"x2-3/4" (1) N OTICE Handle Dry w all Anchors (2) Cle v is Pin 5/16"x1" (1) Cle v is Pin 5/16"x1-1/4" (1) Hex Bolt 5/16"-1 8 x7/ 8 " (4) Rope Ring Fasten[...]
-
Pagina 8
8 T o avoid SERIOUS damage to garage door opener , use ONL Y those bolts/fasteners mounted in the top of the opener . ASSEMBL Y STEP 1 Fasten the Rail to the Motor Unit MODELS 1355M AND 1345M ONL Y (For Models 1356M and 1346M see page 9) • Remove the two washered bolts mounted in top of motor unit. • Position rail at an angle to opener so one h[...]
-
Pagina 9
9 ASSEMBL Y STEP 3 Fasten the Rail to the Motor Unit MODELS 1356M AND 1346M ONL Y • Remove the two washered bolts mounted in top of motor unit. • Align rail and styrofoam over sprocket. • Cut tape from rail, chain and styrofoam. Remove styrofoam and pull the chain back (away from the mounting plate). • Fasten the rail with the two washered [...]
-
Pagina 10
10 ASSEMBL Y STEP 4 Attach the Chain Spreader and Re-install the Chain MODELS 1356M AND 1346M ONL Y • Line up the holes in the chain spreader with the holes in the motor unit as shown. The slot in the chain spreader must fit over the Rail flange (Figure 1). • Securely fasten the chain spreader with the hardware provided. • Remove the trolley [...]
-
Pagina 11
11 ASSEMBL Y STEP 5 Tighten the Chain ALL MODELS • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown. AS YOU TURN THE NUT , KEEP THE CHAIN FROM TWISTING. • When the chain is approximately 1/2" (13 mm) above the base of the rail at its[...]
-
Pagina 12
12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRA CK 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the [...]
-
Pagina 13
13 Header W all V ertical Centerline of Garage Door 2x4 Unfinished Ceiling 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Str u ct u ral S u pports ONE-PIECE DOOR WITHOUT TRA CK 1. Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door , as shown. If headroom clearance is minimal,[...]
-
Pagina 14
14 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header brac ket over drywall. If installing into masonr y , use concrete anchors (not pr ovided). W ALL[...]
-
Pagina 15
15 Clevis Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NO TE: If the door spring is in the way y ou’ll need help . Hav e someone hold the opener securely on a temporary suppor t t[...]
-
Pagina 16
16 ONE-PIECE DOOR WITHOUT TRA CK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height. • The top of the door should be level with the top of the motor unit. Do not position the opener more than 2" ([...]
-
Pagina 17
17 INST ALLA TION STEP 5 Hang the Opener T wo representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware ar[...]
-
Pagina 18
18 T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJURY or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a minimu[...]
-
Pagina 19
19 INST ALLA TION STEP 7 Install the Light and Lens INST ALL THE LIGHT • Install an A19 standard neck, 75 watt maximum light bulb in the socket. The light will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFF . • Use standard neck Garage Door Opener bulbs for replacement INST ALL THE L[...]
-
Pagina 20
20 INST ALLA TION STEP 9 Electrical Requirements T o av oid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, c[...]
-
Pagina 21
21 Invisible Light Beam Protection Area Safety Reversing Sensor 6" (15 cm) max. above floor Safety Reversing Sensor 6" (15 cm) max. above floor Facing the door fr om inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety rever sing sensor must be connected and aligned correctly bef ore the garage door opener w[...]
-
Pagina 22
22 DOOR TRA CK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door T rack FLOOR MOUNT (RIGHT SIDE) W ALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Fi g ure 1 Fi g ure 2 Fi g ure 3 Fi g ure 4 W ALL MOU[...]
-
Pagina 23
23 Carriage Bolt 1/4"-20x1/2" Lens Wing Nut 1/4"-20 Figure 5 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door . Be sure the lens is not obstructed by [...]
-
Pagina 24
24 INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinfor cement brace should be long enough to be secured to two or three vertical supports. A vertical reinfor cement brace should cover the height of the top panel. Figure 1 shows one piece[...]
-
Pagina 25
25 Header W all V ertical Centerline of Garage Door Finished Ceilin g Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 S u pport For a door w ith no exposed framing, or for the optional installation, u se lag scre w s 5/16"x1-1/2" ( N ot Pro v ided) to fasten door b racket. MET AL DOOR T op of Door (Inside Garage) Door B[...]
-
Pagina 26
26 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t[...]
-
Pagina 27
27 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adj[...]
-
Pagina 28
28 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev[...]
-
Pagina 29
29 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weath[...]
-
Pagina 30
30 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made[...]
-
Pagina 31
31 OPERA TION Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you pu[...]
-
Pagina 32
32 T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push button. The loc kout f eature prevents the trolley from reconnecting automatically , Pull the emergency release handle down and back (tow[...]
-
Pagina 33
33 Having a Problem? 1. The opener doesn't operate from either the Door Control or the remote contr ol: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.) • Have you disabled all door locks? Review installa[...]
-
Pagina 34
34 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only . If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between [...]
-
Pagina 35
35 *3-Button Remotes If supplied with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes Fr om Motor Unit Memory T o deactivate any unwanted remote, first e[...]
-
Pagina 36
36 1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button. 3. Release the button when the motor unit lights blink. It has learned the code. [...]
-
Pagina 37
37 7 U P C E I L I N G M O U N T O N L Y 11 10 NOTICE 5 6 8 1 4 9 12 3 2 Installation Parts REP AIR P ARTS KEY P ART NO . NO . DESCRIPTION 1 41A4166 Door control button 2 371LM Single-button remote control 3 10A20 3 V 2032 Lithium battery 4 29B137 T ransmitter visor clip 5 41A2828 Emergency release rope & handle assembly 6 41B4494-1 2-conductor[...]
-
Pagina 38
38 Motor Unit Assembly Parts 2 1 2A 10 8 13 14 15 16 19 4 3 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 9 20 16 12 18 11 17 3 1A 5 6 7 KEY P ART NO . NO . DESCRIPTION 1 41A4208-2 Chain spreader w/screws (1356M, 1346M) 1A 31D380 Sprocket cover (1355M, 1345M) 2 41C4206 Gear and[...]
-
Pagina 39
39 ACCESSORIES C L O SED O P E N L O C K L IG H T 374LM 370LM 915LM 395LM 990LM 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from car , bedside, or[...]
-
Pagina 40
© 2008, The Chamberlain Group, Inc. 1 14A3587 All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SER VICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS Y OUR TELEPHONE. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1- 8 00-52 8 -9131 www .liftmaster .com For prof essional installation, parts and service, con[...]