Char-Broil SANTA FE 10301569 manuale d’uso

Product Guide Model 10301569 Estimated Assembly Time: 1 Hour T ools needed for assembly: Phillips Screwdriver Flat Head Screwdriver T wo adjustable wrenches Hammer Santa Fe FOR OUTDOOR USE ONL Y CA UTION: Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook. INST ALLER/ASSE[...]

D ANGER Safety Symbols The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNING W ARNING: Indicates an potentially hazardous situation which, if not av[...]

PREP ARING T O USE YOUR SANT A FE GRILL Before cooking with your Santa Fe Grill, the following steps should be closely followed to both cure the finish 3 and season the interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first foods. 1. Brush all interior surfaces including grills and [...]

THE HEA T OF THE COALS seconds you can hold the palm of your hand 4 inches above the coals temperature range (Fº) visual cues HOT COALS 2 400 to 450 barely covered with gray ash; deep red glow MODERA TEL Y HOT 375 to 450 thin coating of gray ash; deep red glow MODERA TEL Y HOT COALS 4 325 to 375 significant coating of gray ash; red glow MODERA TEL[...]

Direct and Indirect Grilling Direct Grilling - For most grilling, the ignited coals are spread in a single layer under the food. This is called direct grilling and is appropriate for relatively quick-cooking items such as hamburgers, steaks and most seafood. The single layer of coals emits even, steady heat, whether the grill lid is open or closed,[...]

LIMITED W ARRANTY 6 This warranty only applies to units purchased from an authorized retailer . Manufacturer warrants to the original consumer -purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date[...]

M A S N G F K J I H C B D E L L O P R Q S U P ARTS LIST T 7 V W D K ey Q ty D escri pti on A 1 Fi rebox Asse m bl y B 1 R ear P an e l C 1 Li d D 1 Lo go P l ate E 1 G rease C an h ol der F 2 Lon g Le g G 2 Sh ort Leg H 2 Si de S h elf Bracket, LH F / R H R I 2 S i de Sh el f B racket , LH R / R H F J 4 D ai sy Wh ee l D amper K 1 Li d H an dle L 2[...]

2 • Open carton and place contents onto a clean floor . 1 • Place bottom on ground with clean out door opening facing ground. • Attach rear panel to the bottom with (3) 1/4-20x1/2” hex screws. • With lower section still in position from previous step, attach (1) short leg to the right end and (1) Long leg to left end of the bottom assembl[...]

3 4 This may require at least two people . • Insert a cotter pin through the hole in one end of the axle and bend it so it won’t back out (A). Axle Cotter pin A Cotter Pin Axle 9 Slide a wheel onto the axle. Slide axle through hole in bottom of short leg as shown. Slide the other wheel onto the end of the axle. Insert the remaining cotter pin t[...]

5 6 Attach Handle Bracket to top assembly using (2) 1/4-20x1/2” screws through Bracket placing screws through front holes and attaching with (2) 1/4-20 flange nuts. Place temperature gauge through the hole above the front handle. 10 • Place top assembly on top of bottom assembly . Align hinge hole on back of unit. With aid of a helper attach hi[...]

8 • Slide hook end of (1) wire door stop into slot in end panel of top assembly with hook facing back of the grill. • Next slide the other end through slot in end panel on bottom assembly . With aid of a helper attach lower end of door stop to Bottom assembly using (1) 1/4-20x3/4” ) hex screw from outside and (1) 1/4” flat washer and a reve[...]

10 9 grill using (2) 1/4-20x1/2” long hex screws and (2) 1/4” flange nuts each. 12 Attach left and right shelf brackets to both ends of • Attach (3) slats to each set of shelf brackets using (6) #10-24x1/2” screws. DO NOT TIGHTEN UNTIL ALL SLA TS ARE A TT ACHED. Lid shown removed for clarity . 1 1 attached hanger hooks should be facing away[...]

13 • T o install grease can holder , insert hook through the large hole from the bottom and seat hook into smaller hole. 13 Y our SANT A FE GRILL is now ready for use. Swingaway Grate hole (each side) ? Insert the swing away grate rod into the hole on the left side of the lid, then insert the rod into the hole on the right side of the lid. Shown [...]

HARD WARE LIST Hardware is shown actual size. Y ou may have spare hardware after assembly is complete. 1/4-20 Flanged Lock Nut Qty .33 1/4” Flat W asher Qty .10 1/4-20x1/2” Hex Screw Qty .37 Cotter Pin Qty:2 #10-24x1/2” Screw Qty . 12 #1/4-20 Reversible Lock Nut Qty . 6 14 1/4-20x3/4” Hex Screw Qty .6[...]

[...]

REGTEMP REV02 W arranty Registration Department P .O. Box 1240 Columbus, GA 31902-1240[...]