Chauvet Vue II manuale d’uso

Chauvet, 3000 N 2 9 th Ct, Hollywood, FL 3 3020 U.S.A. (800) 762-1084 – (954 ) 929-1115 FAX (954) 929-5560 www.chauvetlightin g.com V ue™ II Snapshot Ok on Dimmer Outdoor OK Sound Activated DMX512 Master/Slave 115V/230V Switch Replaceable Fuse User Serviceable Duty Cycle USER MANUAL[...]

T ABLE OF C ONTENTS 1. BEFORE YOU BEGIN ............................................................................................................................... .3 W HAT IS INCLUDED ............................................................................................................................... .......... 3 U NPACKING I NSTRUCT[...]

1. B EFORE Y OU B EGIN What is included ¾ 1 x Vue™ II ¾ Power Cord ¾ W arranty Card ¾ User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Noti fy the shipper immediately and retain packing materi[...]

Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. • Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that the y also receive this instruction booklet. • Always make sure that you are c[...]

2. I NTRODUCTION Features • 6-channel DMX-512 LED moon flower • Blackout/static/dimmer/strobe • Individual control of red, green and blue LEDs • Built-in automated programs via master/slave or DMX • Built-in sound activated programs via master/slave or DMX Additional Features • Creates firework -like projections • Additional power out[...]

Product Overview Tilt Adjustment Knob Hanging Bracket Power LED Microphone Signal/Sound Indicator LED Power Output Connector Dipswitches DMX Output Connector DMX Input Connector Sound Sensitiv ity Knob AC Power Input & Fuse Vue™ II User Manual 6 2007-05-10/13 :15[...]

3. S ETUP Disconnect the power cord before replacing a fuse and always replace with the same type fuse. Fuse Replacement The fuse is located inside this compartment. Remove using a flat head screwdriver. With a flat head screwdriver wedge the fuse holder out of its h ousing. Remove the damaged fuse from its holder and replace with exact same type f[...]

CABLE CONNECTORS This drawing prov ides a general illustration of the DMX Input/Output panel of a lighting fixture. U X Controller niversal DM Continue t he link Cabling must have a male XLR connector on one end and a female XLR connector on the othe r end. can cause a ground loop, and your fixt ure may perform erratically. Test cables with an ohm [...]

Often, the se tup for Master-S lave and Standalone op eration requires at the first f ixture i n t he chain be itialize d for this pur pose via ei ther ttings in the co ntrol panel or DIP- th in s e switches. Secondarily, the f ixture s that follow may also requir e a slave setting. Please consult the “Operating Instruct ions” sect io n in this[...]

4. O PERATING I NSTRUCTIONS Operation Stand-Alone Mode (Sound-Active, Au to Mode, Strobe Mode, All On): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. 1) Set dipswitches position to Sound-Active or Auto Mode. Mode Dipswitches Sound-Active 1-8: Off, 9: On, 10: Off Auto Mode 1-4: Effect spee[...]

DMX Mode This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page 15. 1) Set dipswitches 1-9 to the desired DMX addr ess. For help setting the address, see the “SETTING THE STARTING ADD RESS” section on the next page. DMX Channel Values C HANNEL V ALU E F UNCT[...]

SETTING THE STARTING ADDRESS This DMX mode enables the use of a uni versal DMX controller device. Each fixture requires a "sta rt address" from 1 to 512. A fixture requiring one or mo re chan nels for control begins to read the data on the channel indicated by the start address. For example, a fixtur e that uses 6 D MX channels and was ad[...]

DMX QUICK R EFERENCE CHART DMX Address Quick Reference Chart Dip Switch Position DMX DIP SWITCH SET #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1=ON #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X=OFF or ON #6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 #1 #2 #3 #4 #5 0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 1 0 0[...]

General Troubleshooting Applies to Symptom Solution(s) Light s Foggers & Snow Controllers Dimmers & Chaser Auto shut off Check f an thermal switch reset 9 Beam is very dim or not bright Clean optical system or replace lamp Check 220/110v switch for proper setting 9 Breaker/Fuse keeps blowing Check total load placed on device 9 Chase is too [...]

Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A. ) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Pre ss 4) Fax: (954) 929-5560 - (Att ention: Service) Website: http://www.chauvetlighting.com 5. A PPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned i[...]

Returns Proced ure Returned merchandise must be sent prepaid and in t he original packing, call tags will not be issued. Package must be clearly labeled with a Return Merc handise Author ization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and reque st RA # prior to shipping the fixture. Be prepared to provide the [...]