Cisco Systems NPE-225 manuale d’uso

Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Netw ork P r ocessing Engine and Netw ork S er vices Engine Installation and Conf iguration Pr oduct Number: NPE-1 0 0=, NPE-150= , NPE-175=, NPE-20 0=, NPE-225=, NPE-30 0=, NPE[...]

THE SPECIFICATION S AND INFORMATION REGARDING THE P RODUCTS IN TH IS MANUAL AR E SUBJECT TO CHANGE WITHOUT NOT ICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDATI ONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSI BILITY FOR THEIR APPLICATION OF ANY P[...]

iii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 CONTENTS Preface i Document Revision History i-i Objectives i-ii Organization i-ii Related Documentation i-iii Obtaining Documentation and Submitting a Serv ice Request i-iv CHAPTER 1 NPE-100, NPE-150, and NPE-200 Overview 1-1 Supported Platforms 1-[...]

Contents iv Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 System Management Fu nctions 3-4 Terms and Acronyms 3-4 NPE-300 and NPE-400 Memory Information 3-5 CHAPTER 4 NSE-1 Overview 4-1 Supported Platforms 4-1 Software Requirements 4-1 NSE-1 Descrip tion and Overview 4-1 Components 4-2 System Ma[...]

Contents v Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Bandwidth Requirements 6-3 Components 6-3 Interfaces 6-4 LEDs 6-5 CompactFlash Disk 6-6 USB Ports 6-8 Summary of Important NPE-G2 Information 6-9 System Management Functions 6-10 Terms and Acronyms 6-10 NPE-G2 Memory Information and Specifica[...]

Contents vi Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Installing an SFP Module—NPE-G2 7-20 Installing a GBIC—NPE-G1 7-23 Replacing the DIMM on the NPE-G2 7-24 Upgrading the SDRAM SODIMMs on the NPE-G1 (Op tional) 7-26 Removing a SO DIMM 7-26 Installing a SDRAM SODIMM 7-27 Inserting the N[...]

Contents vii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Configuring the Interface Transmission and Speed Modes 7-57 Sample Configuration for the Gigabit Ethernet Interfaces 7-57 Debugging 7-58 Resetting the Interface 7-58 Clearing Counters 7-59 Using show Commands to Check the Installa tion 7-59[...]

Contents viii Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Removing the NPE or NSE 9-9 Removing and Installin g Memory 9-11 Removing DRAM SIMMs 9-11 Installing DRAM SIMMs 9-13 Removing SDRAM DIMM s 9-14 Installing SDRAM DIMMs 9-1 6 Removing a SDRAM SODIMM 9-18 Installing a SDRAM SODIMM 9-19 Che[...]

Contents ix Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Replacing a Power Supply in a Cisco 720 0 Series Router 10-15 Fiber Optic Cleaning Information 10-17 I NDEX[...]

Contents x Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12[...]

i Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Preface This preface describes th e objecti ves and or ganization of this document and e xplains ho w to f ind additional informati on on related products and servi ces. This preface contains the follo wing sections: • Document Re vision History , p[...]

ii Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Preface Objectives Objectives This document incl udes an ov ervie w of each netw or k processing engine (NPE) or net work services engine (NSE), instructions for re mo ving and installi ng an NPE or NSE, steps for v erifying that the installed NPE[...]

iii Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Preface Related Documentation Related Documentation Y our router and the Ci sco IOS software runnin g on it contain e xte nsi ve features and fu nctionality , which are documented in the f ollo wing resources: • Cisco IOS software: For conf igurat[...]

iv Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Preface Obtaining Documentation an d Submitting a Se rvice Request • Cisco 7200 Series Router s Documentation Roadmap at http://www .cisco.com/en/US/docs/routers/ 7200/ roadmaps/7200_seri es_doc_roadmap/3512.html for a list of all Cisco 7200 ser[...]

CH A P T E R 1-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 1 NPE-100, NPE-150, and NPE-200 Overview This chapter describes the netwo rk processing engi ne (NPE) models NPE- 100, NPE-150, and NPE-200 and contains the following sections: • Supported Platfor ms, page 1-1 • Software Requiremen[...]

1-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Desc ription and Overview • The network processing engine maintains and e xec utes the system management functions for the Cisco uBR7200 series routers. The NPE also[...]

1-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Description and Overview Figur e 1- 2 N P E - 1 5 0 1 System controller 7 Midplane co nnectors 2 R4700 microprocessor 8 T emperature sensor 3 1-MB SRAM (U700 through U70[...]

1-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Desc ription and Overview Figur e 1- 3 N P E - 2 0 0 The NPE-100, NPE-150, and NPE-200 consist of t he follo wing components: • Reduced instruction set computing (RI[...]

1-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE-200 Description and Overview • Upgradable memory modules The NPE-100, NPE-150, and NPE-200 use DRAM for storing r outing tables, netw ork accounting applications, packets [...]

1-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE- 200 Memory Information • O TP—one time p rogrammable • Primary , secondary , tertiary cache—Hierarchical cache memory storage based on the p roximity of the cache[...]

1-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NP E-200 Memory Information NPE-100 Memory Information Ta b l e 1-1 pro vides information about memo ry specificat ions. Ta b l e 1-2 provid es memory config urations for the NP[...]

1-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 1 NPE-100, NPE-150, and NPE-200 Overview NPE-100, NPE-150, and NPE- 200 Memory Information NPE-200 Memory Information Ta b l e 1-5 prov ides information about memory specif ication s. Ta b l e 1-6 provid es memory conf igurations for the [...]

CH A P T E R 2-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 2 NPE-175 and NPE-225 Overview This chapter describes the netw ork processing engin e (NPE) models NPE-175 and NP E-225 and contains the follo wing sections: • Supported Platfor ms, page 2-1 • Software Requirement s, page 2-1 • N[...]

2-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Desc ription and Overview Components Figur e 2-1 NPE-175 1 Network controller board 6 Handle 2 System controller 7 Midplane connecto rs 3 Processor engine board 8 Boot R O M (U1) 4 Capti [...]

2-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Description and Overview Figur e 2-2 NPE-225 The NPE-175 and NPE-22 5 consist of the follo wing compon ents: • Reduced instruction set computing (RISC) microprocessor – The NPE-175 has [...]

2-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Desc ription and Overview • Boot R OM for storing suf ficient code for booting the Ci sco IOS software; the NPE-175 an d NPE-225 ha v e boot R OM Note Neither the NPE-175 nor the NPE-22[...]

2-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Memory Information • SRAM—static random-access memory • Unified cache— Instruction cache and data cache are combined. For e xample, a processor may have primary cache with separate [...]

2-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 2 NPE-175 and NPE-225 Overview NPE-175 and NPE-225 Memory Information Ta b l e 2-2 NPE-1 75 SDRAM DIMM Configur ations—Configur able Memo ry Only T otal SDRAM Bank Quantity Product Number 64 MB U15 1 64-MB DIMM MEM-SD-NPE-64MB 128 MB U1[...]

CH A P T E R 3-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 3 NPE-300 and NPE-400 Overview This chapter describes the netw ork processing engin e (NPE) models NPE-300 and NP E-400 and contains the follo wing sections: • Supported Platfor ms, page 3-1 • Software Requirement s, page 3-1 • N[...]

3-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Desc ription and Overview NPE-300 and NPE-400 Description and Overview This section contains information about the netw ork processing engine compo nents and the system management functio[...]

3-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Description and Overview Figur e 3-2 NPE-400 The network processing engines consist of the follo wing component s: • Reduced instruction set computing (RISC) microprocessor – The NPE-30[...]

3-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Desc ription and Overview • Upgradable memory modules The NPE-300 and NPE-400 use SDRAM fo r storing all pack ets receiv ed or sent from netw ork interfaces. The SDRAM also stores routi[...]

3-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information • Primary , secondary , tertiary cache—Hierarchical cache memory storage based on th e proximity of the cache to the core of the processor . Primary ca che is closest[...]

3-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information cisco 7206VXR (NPE400) processor (revision 0xFF) with 122880K/8192K bytes of memory. Processor board ID 8771013 R7000 CPU at 350Mhz, Implementation 39, Rev 2.1, 256KB L[...]

3-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information 32 MB 4 + 128 MB U45 and U44 or U45 2 64-MB DIMMs or 1 128-MB DIMM MEM-SD-NPE-64MB MEM-SD-NPE-128MB 32 MB 4 + 256 MB U45 and U44 2 128-MB DIMMs MEM-SD-NPE-256MB 1. Refer [...]

3-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 3 NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Memory Information[...]

CH A P T E R 4-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 4 NSE-1 Overview This chapter describes the netw ork services engine (NSE-1) and contains the foll owing sections: • Supported Platfor ms, page 4-1 • Software Requirement s, page 4-1 • NSE-1 Description and Overvie w , page 4-1 ?[...]

4-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Description and Over view Note The NSE-1 is not supported in t he Cisco uBR7200 VXR series routers, e v en though it is physically capable of being insert ed into the routers. Components Figur e 4-1 NSE-1 The NSE-1[...]

4-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 4 NSE-1 Overview NSE-1 Description and Overview • System co ntroller The system controller provides hardware logi c to interconnect the processor , DRAM, and the PCI-based system backplane bus. The NSE-1 has on e system controller that pr[...]

4-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Memory Information • Primary , secondary , tertiary cache—Hierarchical cache memory storage based on the p roximity of the cache to the core of the processor . Primary ca che is closest to the processor core an[...]

4-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 4 NSE-1 Overview NSE-1 Memory Information Secondary cache 256 KB — RM7000 processor , internal, unifi ed cache U22 T ertiary cache 2 MB (fixed) — RM7000 processo r , e xternal cache 2 U7, U9, U12, U14, U17 1. OTP = one time programmable[...]

4-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 4 NSE-1 Overvie w NSE-1 Memory Information[...]

CH A P T E R 5-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 5 NPE-G1 Overview This chapter de scribes the NPE-G1 an d contains the follo w ing sections: • Supported Platfor ms, page 5-1 • Software Requirement s, page 5-1 • NPE-G1 Descri ption and Ov ervie w , page 5-2 • NPE-G1 Memory In[...]

5-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview NPE-G1 Description and Overview This section contains information about the NPE-G1 components and the system management functio ns. The NPE-G1 is the first net processing engine for the Ci[...]

5-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview Components Figure 5-1 illustrates the NPE-G1 an d its major components. Figur e 5-1 NPE-G1 The NPE-G1 consists of the f ollow ing components: • BCM1250 system – Microprocessor operates a[...]

5-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview – Three Gigabit Ethernet interf aces (six ports: th ree GBI C [optical] and three RJ-45s [copper]). Any three ports are a vailable at the same time and are linked directly to the BCM1250[...]

5-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview • Only one port per interf ace can be used at any one time. F or example, for in terface Gigabit Ethernet 0/1, either the RJ-45 port can be used o r the GBIC port, b ut not both. • A tot[...]

5-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview CompactFlash Disks are smaller in size than T ype 2 Flash Disks but pro vide the same Attachment (A T A) interface and eq uiv alent fun ctionality . This interf ace complies with the ANSI [...]

5-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview T o remov e a CompactFlash Disk from the CompactFl ash Disk slot, complete the follo wing steps: Step 1 Press the ejector button on the slot. (See 3 in Figure 5-4 .) Step 2 Grasp the Compact[...]

5-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Description and Overview • The NPE-G1 uses no ban dwidth points, and wh en used with any I/O co ntroller , the I/O cont roller also uses no band width points. None of the Gigabit Ethernet interfaces on the NPE-G[...]

5-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview NPE-G1 Memory Information • Primary and secondary cache—Hie rarchical cache memory storage based on the pr oximity of the cache to the core of the processor . Primary cac he is closest to the processor core and has the[...]

5-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Connection Equipment and Specifications This section contain s connection equipment and pinout informati on for the Gi gabit Ethernet RJ-45 p orts, Gigabit Interface Con verter (G[...]

5-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Note T o comply with EMI EN550 22 Class B regulations, shi elded Ethernet cables must be used with the UBR7200-NPE-G1 in the Ci sco uBR7246VXR router . Three shield ed cables are i[...]

5-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Figur e 5-6 Fou r T wisted-P air Straight-Thr ough Cable Schematics f or 1 0/1 00/1 0 00 and 1 0 00BASET GBIC Mo dule P or ts Figur e 5-7 Four T wist ed-P air Crosso ver Cable Sc [...]

5-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Figur e 5-8 Ether net/Fast Ether net Straight-Through and Crosso ver Cable Pinouts For strai ght-through and cross o ver cable information, see the “Consol e and Auxiliary Port C[...]

5-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Figure 5-10 sho ws the simple x and duple x SC-type connectors on your multi mode or single-mode optical f iber cables. F or simple x connectors, tw o cable s are required, one ca[...]

5-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Ta b l e 5-6 lists the a v ailable CWDM GBIC options. Ta b l e 5-7 pro vides cabling specifications for the GBICs that you install in Gigabit Ethernet devices. Note that all GBIC p[...]

5-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Mode-Conditioning Patch Cord Description A mode-conditioning patch cord can be used with the WS-G5486= o r GBIC-LX/LH= to allo w reliable laser transmission between the single-mod[...]

5-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications Figur e 5-1 1 Mo de Conditionin g P atch Cor d The mode-conditioning patch cor d assembly is composed of duple x optical f ibers, includin g a single-mode-to-multimode of fset laun[...]

5-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipment and Specifications Note When connecting to an auxiliary port on a Cisco 7200 VXR router , the port will not function at baud rates higher than 19.2k. If the baud rate on the c onnectin g de vice is [...]

5-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 5 NPE-G1 Overview Connection Equipme nt and Specifications The Cisco 7200 series router s ship with a roll-ov er cable. Connection to a termi nal or a modem requires an RJ-45-to -DB-25 adapter, and possibl y a DB-25-to-DB9 adapter . Refer [...]

5-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 5 NPE-G1 Overview Fiber Optic Cleaning Information RJ-45 Auxiliary Port Signals and Pinouts Ta b l e 5-12 lists the RJ-45 auxil iary port signals for the NPE-G1. Fiber Optic Cleaning Information W e strongly recommend cl eaning all optic[...]

CH A P T E R 6-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 6 NPE-G2 Overview This chapter de scribes the NPE-G2 an d contains the follo w ing sections: • Supported Platfor ms, page 6-1 • Software Requirement s, page 6-2 • NPE-G2 Descri ption and Ov ervie w , page 6-2 • NPE-G2 Memory In[...]

6-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview Software Requirements Software Requirements For minim um software release information, see the “Software Requirements” section on page 8-4 . Note The NPE-G2 has its own Cisco IOS software image with the p refix “c7[...]

6-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Bandwidth Requirements The Gigabit Ethernet ports on the NPE-G2 do not use bandwidth point s, nor does the Fast Ethernet management port. When used with an y I/O controller , the Ethernet po[...]

6-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview • Cache memory The NPE-G2 has two levels of cache: primary and secondary cache that are internal to the microprocessor with secondary unifie d cache for data and instruction. • The NPE[...]

6-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview • The port numbering for the interfaces on the NPE-G2 starts with 0/1 an d not with 0/0, as is typical for other interf ace cards. This is to a void con flicts with the Ethernet and Fast E[...]

6-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Figur e 6-3 NPE-G2 LEDs CompactFlash Disk The NPE-G2 has one CompactFlash Disk sl ot that uses CompactFlash Disks. The de vice in this slot is always addr essed as disk2: when using Cisco [...]

6-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview CompactFlash Disks are smaller in size than T ype 2 Flash Disks but pro vide the same Attachment (A T A) interface and equi valent functionality . This inte rf ace complies with the ANSI A T[...]

6-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview T o remov e a CompactFlash Disk from the CompactFl ash Disk slot, complete the follo wing steps: Step 1 Press the ejector button on the slot. (See 3 in Figure 6-4 .) Step 2 Grasp the Compa[...]

6-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Summary of Important NPE-G2 Information Caution The NPE-G2 requir es that you copy and sa v e your running co nfiguratio n file to a CompactFlash Disk, PC Card, or TFTP server befor e you in[...]

6-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Description and Overview Note The Gigabit Ethernet interf aces on the NPE-G2 do not support the Int er-Switch Link ( ISL) VLAN encapsulation protoc ol. W e recommend that customers use the IEEE 802.1Q VLAN encaps[...]

6-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions • SDRAM—synchronou s dynamic random-access memory . • SDRAM-f ixed—SDRAM of a f ixe d size or quantity; can be replaced, b ut not upgraded . • SFP module—small fo[...]

6-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications 2045K bytes of NVRAM. 250603K bytes of USB Flash usbflash0 (Read/Write) 125163K bytes of USB Flash usbflash1 (Read/Write) 250368K bytes of ATA PCMCIA card at slot 2 (Sector [...]

6-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Connection Equipment and Specifications This section contain s connection equipment and pinout informati on for the Gi gabit Ethernet RJ-45 p orts, Gigabit Ethernet SFP ports[...]

6-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Note W ith reference to the RJ-45 pinout in Ta b l e 6-7 , proper common-mod e line terminat ions should be used for the unused Cate gory 5 UTP cable pairs 4/5 and 7 /8. Com[...]

6-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Figur e 6-7 Fou r T wisted-P air Crosso ver Cable Sc hematics f or 1 0/1 00/1 0 00 and 1 0 00BASET SFP Module Ports Figur e 6-8 Ether net/Fast Ether net Straight-Through and [...]

6-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Gigabit Ethernet SFP Connection Equipment The small for -factor pluggable (SFP) port is a 1000- Mb ps optical interface in the form of an LC-type duplex p ort that supports [...]

6-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Ta b l e 6-8 pro vides SFP module specificat ions. The NPE-G2 supports single Gigabit Ethernet inte rfaces based on SFP technology . The follo wing SFP modules are supported [...]

6-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Ta b l e 6-9 pro vides SFP port cabling specif ications. Ta b l e 6-10 pro vides SFP module po wer bu dget information. Ta b l e 6-9 SFP P ort Cabling Specifications SFP Mod[...]

6-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Ta b l e 6-11 pro vides CWDM SFP module option informati on for the NPE-G2. Mode-Conditioning Patch Cord Description A mode-conditioning patch cord can be used with the SFP-G[...]

6-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications Figur e 6-1 1 Mo de-Conditionin g P atch Cor d for an SFP Module The mode-conditioning patch cor d assembly is composed of duple x optical f ibers, inclu ding a single-mode-[...]

6-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specificat ions Note When connecting to an auxiliary port on a Cisco 7200 VXR router , the port will not function at baud rates higher than 19.2k. If the baud rate on the c onnectin g de vic[...]

6-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview NPE-G2 Memory Information a nd Specifications The Cisco 7200 series routers ship with a roll -ov er cable. Connection to a terminal or a modem requires an RJ-45-to -DB-25 adapter, and possibl y a DB-25-to-DB9 adapter . [...]

6-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 6 NPE-G2 Overview Fiber Optic Cleaning Information RJ-45 Auxiliary Port Signals and Pinouts Ta b l e 6-15 list s the RJ-45 auxiliary port signals for the NPE-G2. Fiber Optic Cleaning Information W e strongl y recommend cleaning all op tica[...]

6-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 6 NPE-G2 Overview Fiber Optic Cleaning Information[...]

CH A P T E R 7-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 7 NPE-G1 and NPE-G2 Installation and Configuration Information This chapter pro vides information on installing and configu ring the NPE-G1 and NPE-G2 and contains the following sections: • Preparing for an Upgrade, page 7-2 • Copy[...]

7-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Preparing fo r an Upgrade Ti p Before you begin an y remov al or in stallation procedure, read Chapter 8, “Preparation f or Installation. ” Also, for the NPE-G1, see the[...]

7-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Preparing for an Upgr ade Before you install an NPE-G1 or NPE-G2 in an exi sting router and remo ve the e xisting processor and I/O controller , do the followi ng: Step 1 Copy[...]

7-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Configuration File Copying the Configuration File Caution Before po wering do wn the router to install the NPE-G1 or N PE-G2, you must sa ve the current configur[...]

7-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Configuration File Step 3 Make sure you are at the privileg ed le v el of the EXEC command interpreter (check the system pro mpt for a pound sign [#]). If the syst[...]

7-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Configuration File Step 4 Enter the copy startup-conf ig tftp command. The EXEC command interpreter prompt s you for the name or IP address of the remot e host t[...]

7-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Copying the Configuration File Using a PC Complete the follo wing step s to copy the rout er’ s configuration f ile to a te xt f ile [...]

7-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Processing Engine Ensuring Easy Access to the Router If your Cisco 7200 VXR router or Cisco uBR7200 series router is installed in a standard 19-inch, 4 [...]

7-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Note When poweri ng of f the router , wait a min imum of 30 seconds before po wering it on ag ain. Step 2 Observe the follo wing items:[...]

7-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Processing Engine Figur e 7 -1 Disconnecting P o wer fr om a Cisco 720 0 VXR Router A C-Input P o wer Supply Step 4 Repeat Step 1 throug h Step 3 if a [...]

7-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Figur e 7 -2 Disconnecting P o wer fr om a Cisco uBR7246VXR AC-Input Po w er Supply Step 4 Repeat Step 1 throug h Step 3 if a second p[...]

7-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Processing Engine War ni ng Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure that power is removed f[...]

7-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Step 5 Repeat this step for the –V lead and the ground lead. Note The color coding of the DC-input po wer supply leads depend s on t[...]

7-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Processing Engine Figur e 7 -4 Removing the Str ain-Relief Co ver fr om a Cisco uBR7246VXR Router DC-Input P ow er Supply Step 4 Using a 3/16-inch flat[...]

7-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Figur e 7 -5 Disconnecting P ow er from a Cisco uBR7246VXR DC-Input Po wer Supply Step 5 Using an 8-mm wrench or nut dri ver (or adjus[...]

7-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Removing the Network Processing Engine Removing the NPE or NSE-1 T o remov e the NPE or NSE-1 from a Cisco 7200 VXR router , a Cisco uBR7246VXR or a Cisco UBR7225VXR router[...]

7-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Removing the Network Processin g Engine Figur e 7 -6 Cisco 7200 VXR Router NPE Captive Installati on Scr ews and Handle Step 4 Using a 3/16-inch f lat-blade scre wdri ver , l[...]

7-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Installing the NPE-G1 or NPE-G2 T o instal l the NPE-G1 or NPE-G2 in the router , use the follo wing procedures: • Basic Guide lines, page[...]

7-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Installing a CompactFlash Disk Use the follo wing instruction s to install the CompactFlash Disk . Figur e 7 -7 Installing a CompactFlash Disk[...]

7-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Caution Do not remov e a USB Flash memory module when a read o r write operation to the USB Flash memory module is in prog ress. The router [...]

7-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -9 T ypes of SFP Module Latches Note The SFP module must be installed before you connect the cables to it. The SPF module has three [...]

7-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -1 0 Inserting an SFP Modul e into the NPE-G2 Gigabit Ethernet P o rt 0/1 Use the follo wing procedure to inst all an SFP module i[...]

7-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Installing a GBIC—NPE-G1 Use the instructions in this sectio n to i nstall a GBIC in the NPE-G1. Figur e 7 -1 1 Installing a GBIC in the NPE[...]

7-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Replacing the DIMM on the NPE-G2 T o replace the DIMM on the NPE-G2 , use the following instructions: Step 1 Locate the DIMM on th e NPE-G2.[...]

7-25 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -13 Installing or Remo ving the DIM M on the NPE-G2 Step 4 Gently insert a DIMM into the DIMM sock et. Step 5 Push the release latch[...]

7-26 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Upgrading the SDRAM SODIMM s on the NPE-G1 (Optional) If you ha ve purch ased an SDRAM memory upgr ade for the NPE-G1, replace the SDRAM SOD[...]

7-27 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -15 Removin g or Installing an SDRAM SODIMM Step 3 Remov e the SODIMM from the sock et. A void touching the SODIMM as much as po ssi[...]

7-28 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 5 If the SODIMM appears misalign ed, carefully remov e it and reseat it in the so cket. Push the SODIMM gently back into the sock et un[...]

7-29 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Note The NPE-G1 or NPE-G2 is not fully seated in the rout er midplane until you ti ghten its capti ve installation sc rews. Step 4 If you remo[...]

7-30 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Note Do not use the cable-manage ment bracket as a ha ndle for inserting and remo ving the NPE-G1 or NPE-G2 in the chassis . Y ou must alway[...]

7-31 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 1 Loosen the left and right capti ve installation scr ews on the NPE-G1 or NPE- G2. Step 2 Hold the cable-manag ement bracket so that it [...]

7-32 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -1 9 Installing the Rear Cab le-Management B rac k ets with an NPE- G1 or NPE-G2—Rout er Fr ont-Mounted Step 1 If the back of th[...]

7-33 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -20 Installing the Rear Cabl e-Managem ent Brac k ets with the NPE -G1 or NPE-G2—Rou ter Rear -Mounted Step 1 Align the cable-man [...]

7-34 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Y ou have f inished in stalling the cable-management br ackets. Go to the “Reconnecting Input Po wer and Po wering Up t he Router” secti[...]

7-35 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -23 Installing the Chassis in a T elco-T yp e Rack with an Installed Cable -Manag ement Brac k et Reconnecting Input Power and Power[...]

7-36 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -24 Connecting A C-Input P ower t o a Cisco 7200 VXR Router Step 4 Plug the A C po wer supply cable i nto the A C po wer source. N[...]

7-37 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Reconnecting AC-Input Power to the Cisco uBR7246VXR Router Figur e 7 -25 Connecting A C-Input P o wer t o a Cisco uBR7246VXR Router T o reconn[...]

7-38 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Reconnecting AC-Input Power to the Cisco uBR7225VXR Router T o connect A C-input po wer to the Cisco uBR7225VXR router , complete the follo [...]

7-39 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 War ni ng Before completing any of the following steps, and to prevent short-circuit or shock hazards, ensure that power is removed from the D[...]

7-40 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -28 Str ipping the DC-Input Lines Step 4 For th e Ci sc o 7200 VXR routers, insert the stripped end of th e ground lead al l the w[...]

7-41 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 This completes the steps for reconnecti ng DC-input po wer to a Cisco 7200 VXR router . Proceed to the “Powering Up the Router” section on[...]

7-42 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -29 Connecting DC-Input P ow er to a Cisco uBR7246VXR Rout er Step 3 SIf necessary , use a wire stripper to s trip approximat ely [...]

7-43 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Step 4 Connect the two -hole grounding lu g on the groundin g lead to the M5 gro unding receptacles with the M5 nuts. T ighten the nuts using [...]

7-44 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Installing the NPE-G1 or NPE-G2 Figur e 7 -31 Replacing the Stra in-Relief Co ver on a Cisco uBR7246VXR Ser ies DC-Input Po wer Supply Step 9 Restore current to the –V an[...]

7-45 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Installing the NPE-G1 or NPE-G2 Powering Up the Router T o po wer up a Cisco 7200 VXR router, Cisco uBR724 6VXR router , or Cisco uBR7225VXR router that has an installe d pow[...]

7-46 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr ocessor on the NPE-G1 Note When poweri ng on the router , wait a minimum of 30 seconds before po wering it of f again. Step 3 Listen for the f ans; y[...]

7-47 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Processor o n the NPE-G1 • Upgrade the R OMmon. (The minimum R OMmon version is 12.3-4 r .T3.) • Install the enabling software. Instructions for upgra[...]

7-48 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr ocessor on the NPE-G1 Using the show interface stats Command Use the show interface stats command for infor mation about the interface. Router# show [...]

7-49 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Processor o n the NPE-G1 Using the show mpf cpu Command Use the show mpf cpu co m ma n d t o display the a verage second CPU utilization in the last fi ve[...]

7-50 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Enabling the Second Pr ocessor on the NPE-G1 CPU% per hour (last 72 hours) * = maximum CPU% # = average CPU% Using the show mpf interface Command Using the show mpf interfa[...]

7-51 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Enabling the Second Processor o n the NPE-G1 Gi0/1.201 201 up RX punts 29 Gi0/1.202 202 up Gi0/1.206 206 up Gi0/1.2002 602 up RX punts 26142 Gi0/1.2004 604 up Using the show [...]

7-52 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Saved Configuration to NVRAM Compiled Wed 02-Feb-05 04:57 by ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1) BOOTLDR: Cisco IOS Software, 7200[...]

7-53 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Saved Con figuration to NVRAM Copying the Saved Configuration File from a Flash Disk or PC Card T o cop y the sav ed conf iguration f ile from the Fl ash Disk or [...]

7-54 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Copying the Saved Configuration to NVRAM Downloading the Saved Configuration from the TFTP Server After you install the NPE- G1 or NPE-G2 in the router an d verify a succes[...]

7-55 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Copying the Saved Con figuration to NVRAM Step 4 The system prompts you to select a host or networ k configu ration fi le. The default is host; press Retur n to accept the de[...]

7-56 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Auxiliary and Console Port Information Auxiliary and Console Port Information If the NPE-G1 or NPE-G 2 and an I/O controller are both in stalled in the same system, the con[...]

7-57 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Configuring the Native Gi gabit Ethernet Interfaces Configuring the Interface Transmission and Speed Modes Step 1 After changing the media type , conf igure the speed and tr [...]

7-58 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Configuring the Native Gigabit Ethe rnet Interfaces ip address 10.198.75.35 255.255.255.240 load-interval 30 no keepalive duplex full speed 1000 media-type gbic no negotiat[...]

7-59 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Using show Commands to Check the Installation Clearing Counters Interface counters may be cleared (reset) by using th e command: clear counters GigabitEthernet 0/X (where X i[...]

7-60 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Using show Com mands to Check the Installation T o determine the hard ware conf iguration of your NPE-G1 or NP E-G2, use the sho w version command. The follo wing example s[...]

7-61 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Using show Commands to Check the Installation Use the show controllers command to disp lay initialization blo ck information, transmit ring, recei ve ring, and errors for the[...]

7-62 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Upgrading the Cisco IO S Image and the Boot He lper (Boot Loader) Image 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broa[...]

7-63 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Upgrading ROMmon on the N PE-G1 or NPE-G2 Step 3 Copy the boot helper i mage from the TFTP serv er to flash memory as follo ws: router# copy tftp bootflash: Address or name o[...]

7-64 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Upgrading ROMmon on the NPE-G1 or NPE-G 2 Using the show rom-monitor Command and ROMmon CLI showmon Commands Use the show rom-monitor command if you are in Cisco IOS, or th[...]

7-65 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Troubleshooting the Upgr ade Running new upgrade for first time System Bootstrap, Version 12.2(20031011:151758) [biff] Copyright (c) 1994-2003 by cisco Systems, Inc. ROM:Rebo[...]

7-66 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Troubleshooting the U pgrade ROMmon Upgrade Error Messages One if these error message appears when the upgrade has failed or if the upgrade image is corrupted: • R OMmon [...]

7-67 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 7 NPE-G1 and NPE-G2 In stallation and Config uration Information Upgrading FPGA on the NPE-G2 Upgrading FPGA on the NPE-G2 A field-programmable gat e array (FPGA) device exists on the NPE-G2. FPGA devices do not exist on other Cisco 7200 s[...]

7-68 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 7 NPE -G1 and NPE-G2 Installation and Config uration Information Fiber Optic Cleaning Information[...]

CH A P T E R 8-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 8 Preparation for Installation This chapter pro vides a list of parts and tools you need to remov e and replace th e network processing engine (NPE) or networ k services engine (NSE) in: • Cisco 7200 series rout ers, including the Ci[...]

8-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements If your router is mounted in a 4-post or telco-type rack, make sure you ha ve at least one other person av ailable to assist you with removin g the chassis from the rack [...]

8-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Use the follo wing table to deter mine supported NPEs or the NSE-1 for specif ic routers. Ta b l e 8-1 Rout ers and Suppor t ed NPEs or NSE-1 Router Supported NPEs or NSE Ci[...]

8-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Port Adapter Jacket Card Support The Port Adapter Jacket Card inse rts into the I/O con troller slot of a Cisco 7200 VXR router when an NPE-G2 or NP E-G1 is installe d. T[...]

8-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements • Cisco uBR7 246VXR Cisco IOS Re lease 12.1(6)EC or later releases of 12.1EC with a special boot helper image of 12.0(15)SC [ubr7200-boot-mz.12 0- 15.SC] Cisco IOS Release[...]

8-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements • Cisco 72 04 and Cisco 72 06 Cisco IOS Release 11.1(8) Cisco IOS Rel ease 11.1(5) Cisco IOS Release 12.0 or 12.0S or later releases of 12.0 or 12.0S Cisco IOS Release [...]

8-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Cisco uBR7200 series • Cisco uBR7246VXR — — — Cisco IOS Release 12.0(6)SC or later releases of 12.0SC Cisco IOS Release 12.1(3)EC1 or later releases of 12.1 EC Cisco[...]

8-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Safety Guidelines Follo wing are saf ety guidelines that you should fol low wh en working with an y equipment that connects to electrical po wer or telephone wiri ng. War[...]

8-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Safety Warnings War ni ng IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means danger . Y ou are in a situation that could cau se bodily injury . Before you work on any [...]

8-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements War nun g WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol b edeutet Gefahr . Sie befinden sich in einer Situation, die zu V erletzungen führen kann. Machen Sie sich vor [...]

8-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements Va r n i n g ! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på [...]

8-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Avi so INSTRUÇÕES IMPORT A NTES DE SEGURANÇA Este símbolo de aviso significa perigo. V ocê se encontra em uma situação em que há risco de lesões corporais. Ante[...]

8-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements[...]

8-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Electrical Equipment Guidelines Follo w these basic guidelines when wo rking with any electrical equipment: • Before begin ning any procedures requ iring access to the[...]

8-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 8 Pre paration for Installation Software and Hardware Requirements • Nev er touch unin sulated telep hone wires or te rminals unless the telephone l ine has been disconnected at the network interface. • Use caution when installing or m[...]

8-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 8 Preparatio n for Installation Software and Hardwar e Requirements Figur e 8-3 Hand ling a P or t Adap ter—Si de Vi ew Although the metal carr ier helps to protect the pr inted circuit boards fro m ESD, wear a prev enti ve antistatic [...]

CH A P T E R 9-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 9 Removing and Installing the NPE or NSE This chapter describes ho w to remo ve a netw ork pr ocessing eng ine (NPE) or network services engi ne (NSE) from supported p latforms and also how to install a replacement n etwork processing [...]

9-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution Make sure that at least one other person is a v ailable to support the f ront of the rout er as you slide it out from the rack and, if necessary , to [...]

9-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Powering Down the Router T o po wer do wn a Cisco 7200 series router, Cisco 7204VXR or Cisc o 7206VXR router, or Cisco uBR7200 seri es router , complete the fol[...]

9-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Disconnecting AC-Input Power from a Cisco 720 0 Series Router or Cisco 7200 VXR Router T o disconnect A C-input power f rom a Cisco 7200 series rout er or Cis[...]

9-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-2 Disconnecting P ow er fr om a Cisco uBR7200 Ser ies A C-Input P ow er Supply—Cisco uBR7246 Sho wn Step 4 Repeat Step 1 throug h Step 3 if a second[...]

9-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 3 Remove the cable tie that secures the –V , +V , and gr ound leads to the pow er supply faceplate. Sa ve the cable tie. Note The cable tie that accomp[...]

9-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Disconnecting DC-Input Power fr om a Cisco uBR7246 Router T o disconnect DC-i nput po wer from a Cisco uBR7346 rou ter , complete the fol lowin g steps. War ni [...]

9-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 4 Using a 3/16-inch flat-blade screwdri v er , loosen the screw belo w the +V lead rec eptacle and pull the lead from the connector . Repe at this step f[...]

9-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Note Repeat the Steps 1 to 5 to disconnect secondary po wer supply , if connected. This completes the pro cedure for disconnecting DC-input po wer from a Cisco [...]

9-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-6 Cisco 7200 Series NPE or NSE Cap tive Install ation Scr ews and Handle Step 4 Using a 3/16-inch f lat-blade scre wdri ver , loosen the scre ws th[...]

9-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Removing and Installing Memory This section pro vides instructions for remo ving and inst alling DRAM or SDRAM on a netw ork processing engi ne or network serv[...]

9-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-7 Releasing the SIMM Spring Latc hes Step 6 When both ends of the SIMM are re leased from the socket, grasp the en ds of the SIMM with your thumb a[...]

9-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Installing DRAM SIMMs The DRAM SIMMs on the network processi ng en gine are located in the following sockets: • U18, U25, U4, and U12 on the NPE-1 00 and the[...]

9-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution When inserting SIMMs, use f irm but not e xcessiv e pressure. If yo u damage a sock et, you must return the network processing engi ne or network ser[...]

9-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-9 Opening DIMM Soc k et Latc hes Note The SDRAM DIMM sockets on th e NPE-175, NPE-225, and NP E-300 are paral lel to the circuit board. They are not [...]

9-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-1 1 Handling the DIMM Caution T o pre vent ESD damage, handle the DIMM b y the card edges only . Place a remo ved DIMM on an antistatic mat and sto[...]

9-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE W ith the netw ork processing engine or netw ork services engine in the same orientati on as the previous procedure, install the DIMM in the DIMM socket as fol[...]

9-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Removing a SDRAM SODIMM This section pro vides a p r oc ed u re fo r r e mo vi ng t h e small outli ne dual in-line memory module (S OD I MM ) on the NPE-400[...]

9-19 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-14 Releasing the SODIMM Spr ing La tch Step 5 Remov e the SODIMM you want to repl ace by pulling ou tward on the SODIMM sprin g latches with your thu[...]

9-20 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution SODIMMs are sensitiv e components that are susc eptible to ESD damage. Handle SODIMMs by the edges only; a voi d touching the memory modules, p ins, [...]

9-21 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE SIMMs or DIMMs should b e aligned at the same angle an d the same height as others on the board when properly installed. If the SIMM, DIMM, or SODI MM appears [...]

9-22 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Caution Do not align the netw ork processing engine or netw or k services engine metal carrier between the slot guides (for all e xcept the NPE-175 and NP E-[...]

9-23 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Figur e 9-1 7 Alig ning the NPE Between the Slot Guides on a Cisco uBR7200 Ser ies—Cisco uBR7246 Shown Step 6 Gently slide the network processin g engine all[...]

9-24 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE War ni ng Read the installation instruc tions before you connect the sy stem to its power source. Statement 10 Note When installing an NPE-175, NPE-22 5, NPE[...]

9-25 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnecting AC-Input Po wer to the Cisco 7200 Series Router or Cisco 7200 VXR Router T o reconnect A C-input po wer to a Cisco 7200 series router or Cisco 720[...]

9-26 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Reconnecting AC-Input Power to the Cisco uBR7200 Series Router Figur e 9-19 Conn ecting A C-Input P o wer t o a Cisco uBR7200 Ser ies Router T o reconnect A [...]

9-27 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnecting DC-Input Power to a Cisco 7200 Series Router or Cisco 7200 VXR Router T o reconnect DC-inp ut pow er to a Cisco 7200 series router or Cisco 7200 V[...]

9-28 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-21 Str ipping t he DC-Input Lines Step 4 Insert the stripped end of th e ground lead all the way into the ground l ead receptacle on the DC-input p[...]

9-29 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Reconnecting DC-Input Power to a Cisco uBR7246VXR Router T o reconnect DC-inp ut pow er to a Cisco uBR7246VXR router , complete the follo wing steps: Note The [...]

9-30 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-22 Connecting DC-Input P ower t o a Cisco uBR7246VXR Router Step 3 If necessary , use a wire stri pper to strip approximately 0 .55 inch (14 mm) f [...]

9-31 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Step 4 Connect the two -hole grounding lu g on the groundin g lead to the M5 gro unding receptacles with the M5 nuts. T ighten the nuts using an 8 -mm wrench o[...]

9-32 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Figur e 9-24 Replacing the Str ain-Relief Cov er on a Cisco uBR7246VXR Rout er DC-Input P ower Supply Step 9 Restore current to the –V and +V leads. Note F[...]

9-33 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 9 Removing and Installing the NPE or NSE Removing and Replacing the N PE or NSE Powering Up the Router T o po wer up a Cisco 7200 series router , Cisco 7200 VXR ro uter , or Cisco uBR7200 series router th at has an installe d power supply [...]

9-34 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 9 Removing a nd Installing the NPE or NSE Removing and Replacing the NPE or NSE Step 5 Observe the initi alization process. When th e system boot is complete (a fe w seconds), the networ k processing engine or netw ork services engine be[...]

CH A P T E R 10-1 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 10 Configuration Tasks and Troubleshooting Information This chapter pr ovides conf igurat ion and troubleshooti ng information. T roubleshooting information includes general show commands, show commands specific to the NSE-1, and erro[...]

10-2 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Boot Changes in Cisco IOS Release 12.2 Note Before enabling the PXF processor , you must ha ve IP routi ng and IP CEF switching turned o n. T o manually disable or enab le the PXF p[...]

10-3 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Troubleshooting the NPE-G1 o r NPE-G2 Caution If an NPE-G1 or NPE-G2 is i nstalled in a router with either an C7200-I/O-GE+E or C7200 -I/O-2FE/E I/O controller , or if a Cisco uBR7200[...]

10-4 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information .Troubleshooting the NPE-100 Through NPE-400 • Check the Cisco IOS release running on the router . F or minimum softwa re release information, see the “Software Requirements” [...]

10-5 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NPE or NSE show Commands Image text-base:0x60008900, data-base:0x6141C000 (display text omitted) cisco 7206VXR (NSE-1) processor (revision B) with 57344K/8192K bytes of memory. R7000 [...]

10-6 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 show Commands 0x20:37 35 20 20 20 04 00 02 02 85 1C 0C 4A 02 CB 84 0x30:4E 53 45 31 FF FF FF FF FF FF FF FF FF FF FF FF 0x40:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x[...]

10-7 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NSE-1 show Commands PXF Statistic: Packets RP -> PXF: switch ip: 0 switch raw: 90 qos fastsend: 0 qos enqueue: 0 Total: 90 Packets PXF -> RP: qos pkts: 0 fast pkts: 0 drops:tota[...]

10-8 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 show Commands ICM0(b4~13) = 0x00000 ICM1(b4~13) = 0x00000 ICM2(b4~13) = 0x00010 ICM3(b4~13) = 0x00000 LOCK0(b0~4) = 0x00000 LOCK1(b0~4) = 0x00000 LOCK2(b0~4) = 0x00000 LOCK3(b[...]

10-9 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information NSE-1 show Commands Using the show pxf interface Command The show pxf interface command pro vides a summary of the in terfaces in the router and which PXF features or capabilities are[...]

10-10 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information NSE-1 Error Messages • show pxf featur e nat ? Router# show pxf feature nat ? entry toaster nat entry stat toaster nat processing info tcp toaster nat tcp logging info Router# sh[...]

10-11 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Using Debugging Comman ds and PXF • PXF processor crash and error message: 00:49:37:Fatal pxf interrupt, int_reg=0x80, int_mask=0xFFFF, config=0x1FF40 00 00:49:37:-Traceback= 6055B[...]

10-12 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information PXF Troubleshootin g Information The PXF has 16 processors, only one of which is in us e at a time when there is a lo w traf fic rate. Ev en though only one of th e processors is w[...]

10-13 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information PXF Troubleshooting Information Note CPU usage be comes more ef ficient as packet load increases. For e xample, if you are running at 60 percent CPU with onl y 33 percent of cust ome[...]

10-14 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Removing and Replacing an AC-Input or DC-Input Power Supply WFQ Queues When there is an increase in ignored packets and in the no b uffer coun t, it is possible that the out put we[...]

10-15 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Removing and Replacing an AC-In put or DC-Input Power Sup ply Figur e 1 0-1 P ow er Supply Captiv e Installa tion Scr ews and Handle—Cisco 7200 Series AC-Input P ow er Supply Sho w[...]

10-16 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Removing and Replacing an AC-Input or DC-Input Power Supply Figur e 1 0-2 Hold ing the P ow er Supply—Cisco 72 00 Series A C-Input P ow er Supply Shown Step 3 Align the po wer su[...]

10-17 Network Processing Engine a nd Network Servic es Engine Installation and Configuration OL-4448-12 Chapter 10 Configuration Tasks and Troublesh ooting Information Fiber Optic Cleaning Information Caution T o maintain agency co mpliance requirements and meet EMI emissions standards for the Cisco 7200 series routers with a single po wer supply ,[...]

10-18 Network Processing Engine a nd Network Servic es Engin e Installation and Configuratio n OL-4448-12 Chapter 10 Config uration Tasks and Troubleshooting Information Fiber Optic Cleaning Information[...]

IN-1 Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 INDEX B Bable Manage ment Brack et 4-post Rack 7-34 C Cable Manage ment Brack et How to Install 7-35 Cable-management Brackets NPE-G1 or NPE-G2 7-29 Cables AC Power 7-35 AC power 9-24 Class 1 Laser Product 7-21 Cleaning Information for Fiber Optic [...]

Index IN-2 Network Processing Engine and Network Servi ces Engine Installation and Configura tion OL-4448-12 I Installing and Removi g a CompactFlash Disk 6-7 Installing DIMMs NPE-175, NPE-225, NPE-300, NSE-1 9-14 ip mpf command 7-47 L LEDs I/O 5-4 M Mode-Conditioning Patch Cord Descript ion 5-16 N Native Gigabit Ethernet interfaces Changing Med ia[...]

Index IN-3 Network Processing Engin e and Network Services Engine Installation and Configuration OL-4448-12 Replacing SODIMMs 7-26 Resetting the Interface 7-58 ROMmon upgrade Error Messages 7-66 Running Configuratio n File 5-1 Specifications 5-9 Speed Modes, Configuring 7-57 Summary 5-7 Supported Platforms 5-1 System Management Function s 5-8 Troub[...]

Index IN-4 Network Processing Engine and Network Servi ces Engine Installation and Configura tion OL-4448-12 RJ-45 Port Pinout 6-14 RJ-45 Port Pinouts 5-11 ROMmon, NPE-G1 or NPE-G2 Changing Preferences 7-65 ROM Monitor 7-64 ROMmon upgrade error messages for the NPE-G1 7-66 S Safety Guid elines 8-4 SFP Port Connections, NPE-G2 6-16 show Commands sho[...]