Citizen iDP-3410 manuale d’uso

CITIZEN User's Manual Model : iDP-3410 Dot Matrix Printer Rev.1.00 Newly issued on 20.Oct.1998 Japan CBM Corporation Information Systems Div.[...]

iDP-3410 User’s Manual Declaration of Conformity Manufacturer’s Name : : Japan CBM Corporation Manufacturer’s Address : CBM Bldg., 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Dot Matrix Printer Model Number(s) iDP-3410 (iDP-3410R/P, iDP-3410S/C, iDP-3410T/I) (S.NO.98X0001 - ) Conform to the following Sta[...]

iDP-3410 User’s Manual IMPORTANT SAFETY INSTRUCTIONS • Read all of these instructions and save them for future reference. • Follow all warnings and instructions marked on the product. • Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. • Do not use this product [...]

iDP-3410 User’s Manual grundsätzlich Stecker aus der Steckdose ziehen. Keine Flüssigkeiten oder Aerosolreiniger benutzen. Nut mit einem feuchten Tuch abwischen. • Der Drucker darf nicht in der Nähe von Wasser aufgestellt werden. • Drucker nicht auf einem unstabilen Wagen, Stand oder Tisch aufstellen. Der Drucker könnte herunterfallen und [...]

iDP-3410 User’s Manual IMPORTANT : This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of[...]

iDP-3410 User’s Manual[...]

iDP-3410 User’s Manual SAFETY PRECAUTIONS ----- BE SURE TO OBSERVE In order to prevent hazards to an operator or other persons and damage to property, be sure to observe the following precautions. _ The following describes the degrees of hazard and damages that can occur if the given instructions are neglected or the equipment is incorrectly oper[...]

iDP-3410 User’s Manual WARNING ! _ Never handle the equipment in the following manners, as it may break, become out of order, or overheat causing smoke and resulting in fire or electric shock. If the equipment is used in an abnormal condition, such as when broken, then problems, smoke emission, abnormal odor/noise, and fire can result. If an abno[...]

iDP-3410 User’s Manual PRECAUTIONS FOR INSTALLATION • Do not use or store the equipment in a place exposed to fire, moisture, or direct sunlight, or in a place near a heater or a thermal device where the prescribed operating temperature and humidity are not met, or in a place exposed to much oil, iron powder, or dust. The equipment may become o[...]

iDP-3410 User’s Manual PRECAUTIONS FOR HANDLING Do not handle the equipment in the following manners, because problems may result. • Do not use a power supply other than the specified AC adapter. • Do not print when there is no recording paper or ink ribbon set in the equipment. The print head may be damaged • Be careful not to drop foreign[...]

iDP-3410 User’s Manual DAILY MAINTENANCE • Prior to starting maintenance work, be sure to turn off the main body. • Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case. For severe soiling, dip the cloth in water and wring it, for wiping off the soil. Never use organic solvents, such as alcohol, thinner, tr[...]

iDP-3410 User’s Manual CONTENTS 1. OUTLINE ........................................................................................................................................................ 16 1.1 Features.........................................................................................................................................[...]

iDP-3410 User’s Manual 10.3 Input and Output Signals ..................................................................................................................................... 41 10.3.1 Input and Output Signals.......................................................................................................................... 41 1[...]

iDP-3410 User’s Manual <<< German >>> 4. BETRIEB ...................................................................................................................................................... 145 4.1 Anschluß des Netzteils ..................................................................................................[...]

iDP-3410 User’s Manual 1. OUTLINE This is a small-size dot impact printer developed for various data communication terminals, POS terminals, kitchen-use printers, bank card, terminals, and so on. Its abundant built-in features allow you to widely use this printer for different applications. Prior to using it, read and understand this manual thoro[...]

iDP-3410 User’s Manual h Exclusive AC Adapter Types and Power Cords • 34AD-U (120 V 2-core cord) • 34AD-E (230 V 2-core cord) Character Set F: International Interface CBM Mode R: Serial(RS-232C D-Sub) P: Parallel(CENTRONICS-based) STAR Mode S: Serial(RS-232C mini DIN) C: Parallel(CENTRONICS-based) ESC/POS Mode T: Serial(RS-232C D-Sub) I: Para[...]

iDP-3410 User’s Manual 2.2 Basic Specifications Model Item iDP-3410-*F120 iDP-3410-*F230 Printer mechanism DP-410 Series (CITIZEN) Print method Serial dot impact method (Bi-directional print) Print width 64 mm Print head 9 pins Print speed Approx. 3 lines/sec. (At single-color continuous print) Print columns 40 columns or 42 columns (Selectable w[...]

iDP-3410 User’s Manual 2.3 Paper Specification 2.3.1 Recommended Paper • Type : Normal paper and non-carbon paper • Paper width : 76 +/- 0.5 mm • Paper thickness : Single-sheet paper --- 45 ∼ 55 kg / 1,000 sheets / 1,091 x 788 mm; Copying paper --- Non-carbon paper, 1 original + 1 copy, Total thickness 0.2 mm or less • Roll diameter : ?[...]

iDP-3410 User’s Manual 3. OUTER APPEARANCE AND COMPONENT PARTS 4. OPERATION 4.1 Connecting AC Adapter[...]

iDP-3410 User’s Manual (1)Turn off the Power switch. (2) Connect the cable connector of the AC adapter to the power connector located on the back of the printer. (3) In order to prevent disconnection of the cable connector, put it through a wire saddle, as shown in the figure below. (4) Connect the AC power cord plug to a plug socket. CAUTION : ?[...]

iDP-3410 User’s Manual 4.2 Connecting Interface Cable (1) Turn off the power. (Mating side included) (2) Check the top and bottom of the cable terminals, and connect to the interface connector. (3) Fix the cable terminals. • Serial Interface: Tighten screws, to fix. • Parallel Interface: Turn a stopper, to fix. (4)Connect the cable to a compu[...]

iDP-3410 User’s Manual 4.4 Setting the Cassette Ribbon (1) Open the printer cover. (2) If the ribbon is slackened, turn the knob in the arrow-indicated direction to give the tension to it before setting. (3) While putting the ribbon in between the head cover and platen, push the locking claws into the holder of the printer. (4) Turn the knob of t[...]

iDP-3410 User’s Manual 4.5 Inserting the Paper (1) Put your hands in the concave parts on both sides of the printer cover, and open it until it comes to a stop. (2) Cut the end of the paper roll at close to a right angle. CAUTION : • Be sure to use the specified paper roll. • Use of unspecified paper may adversely affect print quality, printe[...]

iDP-3410 User’s Manual CAUTION : • If the paper is slack, rewind it, to remove the slack. • If the paper is set slantwise, operate the paper-free lever, to correct the paper position. • While printing, do not hold the paper. This can cause a paper jam.[...]

iDP-3410 User’s Manual 4.6 How to Remove Remaining Paper Roll (1) Open the printer cover. (2) Pushing the paper-free lever in the arrow direction, pull out the paper roll. CAUTION : When pulling out the paper (Forward/Reverse direction), be sure to operate the paper- free lever. 4.7 Removing Paper Jam (1) Open the printer cover. (2) Cut off the p[...]

iDP-3410 User’s Manual 4.8 Operation Panel and Display of Error (1) POWER lamp(Green) Illuminated when the power is turned on. (2) ERROR lamp(Red) Illuminated when the printer is out of paper or has a printer mechanical error or communication error. <Details of Errors> • Paper end ----- If the paper runs out, the paper sensor located in t[...]

iDP-3410 User’s Manual 4.9 Operation Flow at Power-on "Clear Data in Buffer" Yes(FEED SW) and Enlarged Red Print Feed SW ? Buffer data FEED SW ? (CONTINUE) 1 Sec. Passed Power-on Yes No Prints" =HexadecimalDump = Dump Mode Test Print No Yes Off On FEED SW ? (AGAIN) 1 Sec. Passed Input Buffer Clear Yes No Off On Buffer Data No Yes P[...]

iDP-3410 User’s Manual 5. DIP SWITCH SETTING 5.1 Location of DIP Switch (1) Turn off the power. (2) Remove a cassette ribbon. The DIP switches are located as shown in the figure below. (Only DS1 provided for the parallel interface)[...]

iDP-3410 User’s Manual 5.2 DIP Switches Setting 1) DIP Switch 1 No. Function ON OFF Upon Shipment from Factory DS1-1 Auto cutter Yes No OFF DS1-2 International characters ON *2 DS1-3 ″ ON *2 DS1-4 ″ See the Table below ON *2 DS1-5 Paper used 2P 1P OFF DS1-6 CR mode See the Table below OFF DS1-7 Number of columns 42 40 ON DS1-8 Buffer size 6K [...]

iDP-3410 User’s Manual 2) DIP Switch 2 No. Function ON OFF Factory Setting DS2-1 Bit length 8 bits 7 bits ON DS2-2 Parity No Yes ON DS2-3 Odd/Even Odd Even ON DS2-4 Communication mode DTR/DSR XON/XOFF ON DS2-5 Baud rate ON DS2-6 ″ ON DS2-7 ″ See the table below OFF DS2-8 Unused − − OFF Baud rate Baud rate(bps) DS2-5 DS2-6 DS2-7 150 OFF OF[...]

iDP-3410 User’s Manual 6. PRESET JUMPER SETTING 6.1 Location of Preset Jumper (1) Turn off the power. (2) Remove a cassette ribbon. (3) Remove the top cover. The preset jumper is located as shown in the figure below. Serial Interface Parallel Interface 6.2 Preset Jumper Table Serial Interface Mode Location CBM STAR ESC/POS SCA 1-C * 2-C 2-C SCB 1[...]

iDP-3410 User’s Manual 8. INPUT BUFFER BACKUP FUNCTION 8.1 Buffer Size With the DIP switch, you can set either 6K bytes or 256 bytes. DIP switch 1-8 ON → 6K bytes OFF → 256 bytes 8.2 Input Buffer Backup Even if the power is turned off or fails during the printing process, the data in the input buffer will be saved. If the power is turned on a[...]

iDP-3410 User’s Manual 9. PARALLEL INTERFACE 9.1 Specifications • Data input system : 8-bit parallel system (DATA1 to DATA8) • Control signals : ACK, BUSY, STB, FAULT, SELECT, RESET, COMPULSION • Applicable connectors : Printer side --- 57LE-40360 (Equivalent to anphenol), Cable side --- 57-30360 (Ditto) 9.2 Connector's Pin Configurati[...]

iDP-3410 User’s Manual 9.3 Input and Output Signals 9.3.1 Input and Output Signals (1) Input signals to the printer • DATA : An 8-bit parallel signal. (Positive logic) • STB : A strobe signal to read the 8-bit data. (Negative logic) • RESET : A signal to reset the printer from the outside.(Negative logic) (2) Output signals from the printer[...]

iDP-3410 User’s Manual 9.3.2 Electrical Characteristics (1) Input signal level All the input signals are at the TTL level. "HIGH" level : 2.0 V at minimum "LOW" level : 0.8 V at maximum (2) Output signal level All the output signals are at the TTL level. "HIGH" level : 2.4 V at minimum "LOW" level : 0.4 V a[...]

iDP-3410 User’s Manual 9.3.3 Timing Chart (1) Data input and printing timing T1, T2, T3 : 0.5 µ s MIN T4 : 270 ns MAX T5 : 2.3 µ s TYP T6 : 500 ms MIN (At power-on) 9.3.4 Data Receiving Control When the BUSY signal is at "LOW," the printer can receive the data from the host, but when at "HIGH," it cannot. 10. SERIAL INTERFAC[...]

iDP-3410 User’s Manual (4) Signal polarity RS-232C • Mark = Logic "1" (-3 V ∼ -12 V) • Space = Logic "0" (+3 V ∼ +12 V) (5) Received data (RXD signal) RS-232C • Mark = 1 • Space = 0 (6) Reception control (DTR signal) RS-232C • Mark : Data transfer disabled • Space : Data transfer enabled[...]

iDP-3410 User’s Manual 10.2 Connector's Pin Configuration Mode No. CBM STAR ECS/POS 1 FG ← ← 2 TXD ← ← 3 RXD ← ← 4 RTS ← 5 6 DSR 7 GND ← ← 8 9 10 11 PE (HI-LEVEL) RCH 12 FAULT 13 GND 14 FAULT 15 mTXD 16 mRXD 17 18 19 20 DTR ← ← 21 22 23 RESET 24 25 Cautions: 1. An RS-232C signal is based on the EIA RS-232C. 2. When the [...]

iDP-3410 User’s Manual 10.3 Input and Output Signals 10.3.1 Input and Output Signals (1) RXD This is a serial received data signal. When a framing error, overrun error, or parity error occurs, that data is printed as "?". (2) DTR When this signal is Ready, write the data or a command. If written at the time of Busy, an overrun error res[...]

iDP-3410 User’s Manual (8) RCH When the printer is ready to receive, this signal is turned to Space. This signal line is the same as DTR. (9) mTXD TXD signal for the diode gate. (10) mRXD RXD signal for the diode gate. (11) FG This is a Frame Ground signal. (12) GND This is a common ground on the circuit. 10.3.2 Data Configuration t Mark b 0 , b [...]

iDP-3410 User’s Manual (1) Start bit After a lapse of 1/2 bit from a mark-to-space fall edge, the state is read again, and if it is a space, it is recognized as the start bit. If it is a mark, it is assumed neither the start bit nor an error, and it is attempted to detect the start bit again. (2) Data bit + parity bit The data bit and parity bit [...]

iDP-3410 User’s Manual 10.3.6 Electrical Characteristics (1) RS-232C circuit Input (RXD, DSR, mRXD) [Printer Side] [Host Side] Output (DTR, TXD, mTXD, RCH, RTS, FAULT) Equivalent to MAX232 DTR Mark=(-8V): At Busy TXD Mark=(-8V): 1 Space=(+8V): At Ready Space=(+8V): 0 (2) Others • RESET : A signal to reset the entire printer. • PE : A signal t[...]

iDP-3410 User’s Manual 11. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR 11.1 Specifications of Drawer Kick-Out Connector (1) Drawer kick-out drive signal Parallel Interface ----- Can be learned at the no. 34 pin of the interface connector Serial Interface ----- Provided with a command to learn the status in the Star and ESC/POS modes. (2) Electr[...]

iDP-3410 User’s Manual 11.4 Specifications of Power Supply Connector This is a power connector from an exclusive AC adapter. Connector’s Pin Configuration No. Function 1 2 +24V GND 1 2 Jack used : HEC0470-01-640(HOSHIDEN) or equivalent Applicable plug : JXP series Type-A (I.D. 2.45 mm, O.D. 5.5 mm) (HOSHIDEN) or equivalent CAUTION: • Be sure [...]

iDP-3410 User’s Manual 12. MAINTENANCE AND SERVICE For the information on maintenance and service, please contact our dealer or at the following address. Northern America Other Areas CBM America Corporation Japan CBM Corporation Service Center Information Systems Division 365 Van Ness Way CBM Bldg., 5-68-10, Nakano Suit 510 Nakano-ku, Tokyo 164-0[...]

iDP-3410 User’s Manual 10 ESC ∗ n1 n2 Specifying the bit image mode 1BH 2AH n1 n2 60 11 ESC − n Specifying/Canceling the Underline 1BH 2DH n 60 12 ESC 1 Specifying 1/9-inch line feed rate 1BH 31H 61 13 ESC 2 Specifying 2/9-inch line feed rate 1BH 32H 61 14 ESC 3 Specifying 1/6-inch line feed rate 1BH 33H 61 15 ESC C n Setting the page length [...]

iDP-3410 User’s Manual XXX Shows a command.[...]

iDP-3410 User’s Manual Details FF n [Function] n-line paper feed [Code] <0C>H n [Range] 1 ≤ n ≤ 127 [Outline] This command feeds the paper by n-lines. You can set n = 1 to 127 lines. If the print buffer contains the data, use of this command feeds the paper by n-lines after printing the data. Setting n = 0 does not feed the paper. SO [F[...]

iDP-3410 User’s Manual SI [Function] Canceling the double width character [Code] <0F>H [Outline] This command cancels the double width characters set with SO. The data following this command are printed in the ordinary character width. LF [Function] Printing and paper feed [Code] <0A>H [Outline] If the print buffer contains the data, [...]

iDP-3410 User’s Manual mixed in one line.[...]

iDP-3410 User’s Manual DC3 [Function] Specifying the red print [Code] <13>H [Outline] This command specifies red-color characters. All the characters in one line are printed in red by prefixing the print data with this command and sending it to the printer. When you want to use red characters, use this command for each line. CAN [Function] [...]

iDP-3410 User’s Manual ESC " ∗ " n1 n2 [Function] Specifying the bit image mode [Code] <1B>H <2A>H n1 n2 [Range] 1 ≤ n1 + 256 × n2 ≤ 378 [Outline] This command allows printing in the bit image mode. Divide the number of dots printed by 256 and assume its quotient to be n2 and remainder to be n1. Therefore, the number [...]

iDP-3410 User’s Manual ESC "3" [Function] Setting the 1/6-inch line feed width [Code] <1B>H <33>H [Outline] This command sets the line feed width to 1/6 inch(Default). ESC "C" n [Function] Setting the page length [Code] <1B>H <43>H n [Range] 1 ≤ n ≤ 127 [Outline] Sets the 1-page length to n-lines.[...]

iDP-3410 User’s Manual ESC "N" n [Function] Specifying the perforation skip [Code] <1B>H <4E>H n [Range] 1 ≤ n ≤ 126 [Outline] This command feeds(Skips) the lines specified with n without printing. However, you cannot specify beyond the length of one page. ESC "O" [Function] Canceling the perforation skip [Code[...]

iDP-3410 User’s Manual ESC "t" n [Function] Selecting the character code table [Code] <1B>H <74>H n [Range] 0 ≤ n ≤ 255 [Outline] This command selects Page-n of Character Code Table. [Default] Depends upon DIP switch setting. n Character Code Table n Character Code Table 0 CBM International 6 Code Page 852 (Eastern Europ[...]

iDP-3410 User’s Manual ESC BEL n1 n2 [Function] Setting the external device drive pulse width [Code] <1B>H <07>H n1 n2 [Range] 1 ≤ n1 ≤ 127 1 ≤ n2 ≤ 127 [Outline] This command sets the power-on time to drive an external device (Cash drawer). Power-on time = n1 × 10 (ms) Delay time = n2 × 10 (ms) To actually drive the drawer,[...]

iDP-3410 User’s Manual FS [Function] Driving command B drawer-1 [Code] <1C>H [Outline] This command drives the drawer connector No. 2 pin under the condition set with the <ESC><BEL> n1 n2 command. SUB [Function] Driving command for drawer-2 [Code] <1A>H [Outline] As soon as this command is received, the drawer connector no[...]

iDP-3410 User’s Manual ESC "R" n [Function] Selecting the international character set [Code] <1B>H <52>H n [Range] 0 ≤ n ≤ 10 [Outline] This command selects the international characters according to the value of n. n Character Set n Character Set 0 U.S.A. 6 Italy 1 France 7 Spain 2 Germany 8 Japan 3 U.K. 9 Norway 4 Denma[...]

iDP-3410 User’s Manual ESC "&" <0> n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] Defining the Download character set [Code] <1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1 [Range] 32 ≤ n1 ≤ n2 ≤ 255 m0 = 0 or m0 = 128 [Outline] This command defines he download characters. n1 is [...]

iDP-3410 User’s Manual ESC "%" n [Function] Specifying/Canceling the download character set [Code] <IB>H <25>H n [Outline] This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. To print them, send this command[...]

iDP-3410 User’s Manual ESC DC3 n [Function] Printing the message [Code] <1B>H <13>H n [Range] 1 ≤ n ≤ 10 [Function] This command prints a message. If the value of n is specified beyond the range, the message will not be printed.[...]

iDP-3410 User’s Manual ESC DC2 n1 n2 [Function] Deleting the download character, message, bit image [Code] <1B>H <12>H n1 n2 [Range] 0 ≤ n1 ≤ 3 0 ≤ n2 (Specify 0 at n1 = 0) (1 ≤ n2 ≤ 10 at n1 = 1) (32 ≤ n2 ≤ 255 at n1 = 2) (Specify 0 at n1 = 3) [Outline] This command deletes the downloaded characters, message, and bit im[...]

iDP-3410 User’s Manual GS " ∗ " n1 n2 [d] n1 × n2 × 8 [Function] Defining the download, bit image [Code] <1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8 [Range] 1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24 Note) Take care that the number of data (n1 × n2 × 8) is equal to or smaller than 2,048. [Outline] This command def[...]

iDP-3410 User’s Manual GS ⁄ m [Function] Printing the download, bit image [Code] <1D>H <2F>H m [Range] 0 ≤ m ≤ 255 [Outline] This command prints the bit image saved in the number specified with m. [Caution] If the print buffer contains the data, this command will be ignored. If the bit image has not been saved in the specified n[...]

iDP-3410 User’s Manual 13.2 STAR Mode 13.2.1 Command List Command Function Code Page 1 ESC R n Sel ecting the inte rnati onal chara cter set 1BH 52H n 75 2 ESC 6 NOP 1BH 36H 3 ESC 7 NOP 1BH 37H 4 ESC M NOP 1BH 4DH 5 ESC P NOP 1BH 50H 6 ESC : NOP 1BH 3AH 7 SO Specifying the double width character 0EH 75 8 DC4 Canceling the double width character 1[...]

iDP-3410 User’s Manual 44 FS Driving command B for drawer-1 1CH 93 45 SUB Driving command for drawer-2 1AH 93 46 RS Buzzer-on 1EH 93 47 CAN Canceling the print data 18H 94 48 DC3 Setting the deselect mode 13H 94 49 DC1 Setting the Select mode 11H 94 50 ESC U n Selecting the Unidirectional/bidirectional print mode 1BH 55H n 95 51 ESC @ Initializin[...]

iDP-3410 User’s Manual Details ESC “R” n [Function] Selecting the international character set [Code] <1B>H <52>H n [Range] 0 ≤ n ≤ 10 [Outline] This command selects the international characters according to the value of n. n Character Set n Character Set 0 U.S.A. 6 Italy 1 France 7 Spain 2 Germany 8 Japan 3 U.K. 9 Norway 4 Den[...]

iDP-3410 User’s Manual DC4 [Function] Canceling the double width character [Code] <14>H [Outline] This command deselects the double width characters set with SO. The data following this command will be printed in ordinary characters. ESC "E" [Function] Specifying the highlight character [Code] <1B>H <45>H [Outline] The[...]

iDP-3410 User’s Manual ESC " − " n [Function] Specifying/Canceling the underline [Code] <1B>H <2D>H n [Outline] This command selects/deselects an underline. The underline is selected at n = 1 and deselected at n = 0. The space by the horizontal tab is not underlined. ESC "4" [Function] Specifying the red print [C[...]

iDP-3410 User’s Manual SI [Function] Specifying the inverted character [Code] <0F>H [Outline] This command selects and prints the inverted characters. Enter it at the beginning of one line. Otherwise, it will be invalid. Erect and inverted characters cannot be mixed in one line. DC2 [Function] Canceling the Inverted character [Code] <12&[...]

iDP-3410 User’s Manual LF [Function] Printing and paper feed [Code] <0A>H [Outline] If the print buffer contains the data, this command will feed the line after printing. If not, the command only feeds the line. CR [Function] Printing [Code] <0D>H [Outline] This command prints the data. If the DIP switch segments 1 to 6 are set to OFF[...]

iDP-3410 User’s Manual ESC "a" n [Function] Setting the n-line paper feed [Code] <1B>H <61>H n [Range] 1 ≤ n ≤ 127 [Outline] This command feeds the paper by the number of lines specified with n. You can set n = 1 to 127 lines. If the print buffer contains the data, use of this command feeds the paper by n- lines after pr[...]

iDP-3410 User’s Manual [Outline] This command feeds the paper to the next vertical tab position. It cannot be fed unless the vertical tab position has been set. If the current position is equal to or greater than the maximum set vertical tab position, it will be fed to the head of the next page.[...]

iDP-3410 User’s Manual ESC "B" [n]k NUL [Function] Setting the vertical tab position [Code] <1B>H <42>H [n]k <00> [Range] 1 ≤ n ≤ 255 1 ≤ k ≤ 16 [Outline] This command cancels the already set vertical tab positions and sets new vertical tab positions. They are set in the ascending order and ends with <00>[...]

iDP-3410 User’s Manual ESC "O" [Function] Canceling the lower margin [Code] <1B>H <4F>H [Outline] This command deselects the set lower margin. ESC "l" n [Function] Setting the left margin [Code] <1B>H <6C>H n [Range] 0 ≤ n ≤ (Right margin - 2) [Outline] This command sets the left margin and printing[...]

iDP-3410 User’s Manual HT [Function] Horizontal tab [Code] <09>H [Outline] This command moves a printing position to the preset next horizontal tab position. This command will be ignored unless there is the next horizontal tab position.[...]

iDP-3410 User’s Manual ESC "D" [n] k NUL [Function] Setting the horizontal tab position [Code] <1B>H <44>H [n] k <00>H [Range] 1 ≤ n ≤ Max. print columns – 1 1 ≤ k ≤ 16 [Outline] This command sets the horizontal tab positions. n indicates the number of lines from the head of the line to the horizontal tab set[...]

iDP-3410 User’s Manual ESC "1" [Function] Setting the 1/9-inch line feed width [Code] <1B>H <31>H [Outline] This command sets the line feed width to 1/9 inch. ESC "2" [Function] Setting the 2/9-inch line feed width [Code] <1B>H <32>H [Outline] This command sets the line feed width to 2/9 inch.[...]

iDP-3410 User’s Manual ESC "K" n1 <0> m1 m2 ... [Function] Specifying the 8-dot standard density bit image [Code] <1B>H <4B>H n1 <00>H m1 m2 ... [Range] 1 ≤ n1 ≤ 378/2 [Outline] This command prints the bit image by the number of data specified with n1. Printing will be unidirectional. The surplus data exceedi[...]

iDP-3410 User’s Manual ESC "L" n1 n2 m1 m2 ... [Function] Specifying the 8-dot double density bit image [Code] <1B>H <4C>H n1 n2 m1 m2 ... [Range] 1 ≤ n1 + 256 × 2 ≤ 378 [Outline] This command prints the 8-dot double density (Half-dot print) bit image. Printing will be unidirectional. The surplus data exceeding the prin[...]

iDP-3410 User’s Manual ESC "h" n [Function] Specifying/Canceling the double height character [Code] <1B>H <68>H n [Outline] The data following this command is printed in double height characters, except the bit image mode <ESC> "K" and <ESC> "L". In combination with the <SO> command, thi[...]

iDP-3410 User’s Manual ESC "&" <O> n1 n2 m0 m1 m2 m3 m4 m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] Defining the download character set [Code] <1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1 [Range] 32 ≤ n1 ≤ n2 ≤ 255 m0 = 0 or m0 = 128 [Outline] This command defines he download characters. n1[...]

iDP-3410 User’s Manual ESC "%" n [Function] Specifying/Canceling the download character set [Code] <IB>H <25>H n [Outline] This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. To print them, send this command[...]

iDP-3410 User’s Manual ESC BEL n1 n2 [Function] Setting the external device drive pulse width [Code] <1B>H <07>H n1 n2 [Range] 1 ≤ n1 ≤ 127 1 ≤ n2 ≤ 127 [Outline] This command sets the power-on time to drive an external device(Cash drawer). Power-on time = n1 × 10 (ms) Delay time = n2 × 10 (ms) To actually drive the drawer, [...]

iDP-3410 User’s Manual FS [Function] Driving command B for drawer-1 [Code] <1C>H [Outline] This command drives the drawer connector no. 2 pin under the condition set with the <ESC><BEL> n1 n2 command. SUB [Function] Driving command for drawer-2 [Code] <1A>H [Outline] As soon as this command is received, the drawer connecto[...]

iDP-3410 User’s Manual CAN [Function] Canceling the print data [Code] <18>H [Outline] This command clears the input buffer and print buffer. In the STX-EXT mode of the serial interface printer, the command clears the data in the data buffer and ends the STX-ETX mode. DC3 [Function] Setting the deselect mode [Code] <13>H [Outline] If t[...]

iDP-3410 User’s Manual ESC "U" n [Function] Selecting the Unidirectional/Bidirectional print mode [Code] <1B>H <55>H n [Range] 0 ≤ n ≤ 255 [Outline] This commands selects or deselects unidirectional print. n0 = 0 Bidirectional print n0 = 1 Unidirectional print ESC "@" [Function] Initializing the printer [Code] [...]

iDP-3410 User’s Manual ENQ [Function] Enquiry [Code] <05>H [Outline] This command is valid only for the serial interface. The printer sends the status information. If this command is entered after receiving the text information in the STX-ETX mode, the printer will send the status information and check byte.[...]

iDP-3410 User’s Manual STX [Function] Text start [Code] <02>H [Outline] This command is valid only for the serial interface. It effectuates the STX-ETX mode. ETX [Function] Text end [Code] <03>H [Outline] This command is valid only for the serial interface. It ends the STX-ETX mode and prints the data.[...]

iDP-3410 User’s Manual *ETX-STX Mode ESC "t" n [Function] Selecting the character code table [Code] <1B>H <74>H n [Range] 0 ≤ n ≤ 255 [Outline] This command selects Page-n of Character Code Table. [Default] Depends on DIP switch setting. n Character Code Table N Character Code Table 0 STAR International 6 Code Page 852 ([...]

iDP-3410 User’s Manual 2 Code Page 850 (Multilingual) 8 Code Page 857 (Turkey) 3 Code Page 860 (Portugal) 9 Windows Code 4 Code Page 863 (Canada-French) 5 Code Page 865 (Norway) 255 Space Page (For user setting)[...]

iDP-3410 User’s Manual ESC " ⁄ " n "data" CR or LF [Function] Defining the message [Code] <1B>H <2F>H n "data" CR or LF [Range] 1 ≤ n ≤ 10 [Outline] This command can define up to a 50-byte message in one line. If the value of n is specified beyond the range, the data following n will be treated as t[...]

iDP-3410 User’s Manual 2 Download characters 3 Download bit image With n2, specify which data of the function specified with n1 should be deleted. n2 = 0 Deletes all the download function specified with n1. n2 ≠ 0 Deletes the data downloaded at the value specified with n2 (Value specified when saving with each download command), of the download[...]

iDP-3410 User’s Manual GS " ∗ " n1 n2 [d] n1 × n2 × 8 [Function] Defining the download, bit image [Code] <1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8 [Range] 1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24 Note) Take care that the number of data(n1 × n2 × 8) is equal to or smaller than 2,048. [Outline] This command defi[...]

iDP-3410 User’s Manual GS ⁄ m [Function] Printing the download, bit image [Code] <1D>H <2F>H m [Range] 0 ≤ m ≤ 255 [Outline] This command prints the bit image saved in the number specified with m. [Caution] If the print buffer contains the data, this command will be ignored. If the bit image has not been saved in the specified n[...]

iDP-3410 User’s Manual increments 11 ESC < NOP 1BH 3CH 12 ESC @ Initializing the printer 1BH 40H 111 13 ESC D [n] k NUL Setting the Horizontal tab position 1BH 44H [n] k 00 112 14 ESC J n NOP 1BH 4AH n 15 ESC R n Sel ecting the inte rnati onal chara cter set 1BH 52H n 113 16 ESC U n Specifying/Canceling the unidirectional print mode 1BH 55H n [...]

iDP-3410 User’s Manual Details HT [Function] Horizontal tab [Code] <09>H [Outline] This command moves a printing position to the next horizontal tab position. If the next horizontal tab position is not set, this command will be ignored. [Caution] The horizontal tab position is set by <ESC> D. Initial setting of the horizontal tab posi[...]

iDP-3410 User’s Manual CR [Function] Printing [Code] <0D>H [Outline] This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer will print the data in the print buffer and feed the paper by one line. If they are set to ON, the printer will print the data in the print buffer and will not feed the paper. ESC &[...]

iDP-3410 User’s Manual ESC "!" n [Function] Setting the print mode batch [Code] <1B>H <21>H n [Range] 0 ≤ n ≤ 255 [Outline] Sets the print mode. "n" (Each bit) has the following meanings. Values Bit Function 0 1 0 Undefined − − 1 Undefined − − 2 Undefined − − 3 High-lighting Canceled Specified 4 Dou[...]

iDP-3410 User’s Manual ESC "%" n [Function] Specifying/Canceling the download character set [Code] <1B>H <25>H n [Range] 0 ≤ n ≤ 255 [Outline] This command selects/deselects the download character set. n is valid only for the least significant bit. Setting n0 = 1 selects the download character set. Setting n0 = 0 deselec[...]

iDP-3410 User’s Manual ESC "&" s n m [a[p] s × a]m - n + 1 [Function] Defining the download character set [Code] <1B>H <26>H s n m [a[p] ... <ps × a>] m - n + 1 [Range] s = 2 32 ≤ n ≤ m ≤ 255 0 ≤ a ≤ 9 0 ≤ p1 ... ps × a ≤ 255 [Outline] This command defines the download alphenumerals or Katakana. s [...]

iDP-3410 User’s Manual ESC " ∗ " m n1 n2 [d] n1 + 256 × n2 [Function] Specifying the bit image mode [Code] <1B>H <2A>H m n1 n2 [d] n1 + 256 × 2 [Range] m = 0, 1 0 ≤ n1 ≤ 255 0 ≤ n2 ≤ 3 0 ≤ d ≤ 255 [Outline] This command specifies the bit image for the mode m as to the number of dots specified with n1 and n2. [...]

iDP-3410 User’s Manual ESC "2" [Function] Setting the 1/6-inch line feed width [Code] <1B>H <32>H [Outline] This command sets the line feed width to 1/6 inch. ESC "3" [Function] Setting the line feed width in minimum pitch increments [Code] <1B>H <33>H [Outline] This command sets the line feed width to [...]

iDP-3410 User’s Manual ESC "D" [n]k NUL [Function] Setting the Horizontal tab position [Code] <1B>H <44>H [n]k <00>H [Range] 1 ≤ n ≤ 255 0 ≤ k ≤ 32 [Outline] This command sets the horizontal tab position. n denotes the number of columns from the head of the line to the horizontal tab setting position and equals[...]

iDP-3410 User’s Manual ESC "R" n [Function] Selecting the international character set [Code] <1B>H <52>H n [Range] 0 ≤ n ≤ 10 [Outline] This command selects the international characters according to the value of n. n Character Set n Character Set 0 U.S.A. 6 Italy 1 France 7 Spain 2 Germany 8 Japan 3 U.K. 9 Norway 4 Denma[...]

iDP-3410 User’s Manual ESC "U" n [Function] Specifying/Canceling the Unidirectional print mode [Code] <1B>H <55>H [Range] 0 ≤ n ≤ 255 [Outline] This command selects/deselects unidirectional print. n is valid only for the least significant bit. n Function 0 Deselects 1 Selects [Caution] If unidirectional print is selected[...]

iDP-3410 User’s Manual [Default] n = 0 ESC "d" n [Function] Printing and n-line paper feed [Code] <1B>H <64>H n [Range] 0 ≤ n ≤ 255 [Outline] This command feeds the paper by n-lines after printing the one line worth of data saved in the print buffer.[...]

iDP-3410 User’s Manual ESC "p" m n1 n2 [Function] Specifying the pulse generation [Code] <1B>H <70>H m n1 n2 [Range] 0 ≤ m ≤ 1 0 ≤ n1 ≤ n2 ≤ 255 [Outline] This command outputs the signals specified with n1 and n2 to the connector pins. m Connector Pin 0 Drawer kick connector No. 2 pin 1 Drawer kick connector No. 5 [...]

iDP-3410 User’s Manual ESC "r" n [Function] Selecting the printing color [Code] <1B>H <72>H n [Range] n = 0, 1 [Outline] This command selects a print color for each line. Setting n = 0 selects black. Setting n = 1 selects red. The command is valid only when it is entered at the head of the line. [Default] n = 0 (Black print)[...]

iDP-3410 User’s Manual ESC "u" n [Function] Sending the status for peripheral device [Code] <1B>H <75>H n [Range] n = 0 [Outline] This commands sends the status of the connector no. 3 pin. n Connector Pin 0 Drawer kick-out connector No. 3 pin Status Sent Value Bit Function 0 1 0 No. 3 pin's level “LOW” “HIGH” 1 [...]

iDP-3410 User’s Manual ESC "v" [Function] Sending the printer status [Code] <1B>H <76>H [Outline] This command sends the printer status. [Caution] This command is valid only for the serial interface. The following table lists the status sent. In case of DTR/DSR control, only one byte will be sent after confirming that the ho[...]

iDP-3410 User’s Manual ESC "{ " n [Function] Specifying/Canceling the inverted character print [Code] <1B>H <7B>H n [Range] 0 ≤ n ≤ 255 [Outline] This command selects/deselects inverted print. n is valid only for the least significant bit. n Type 0 Deselects the inverted characters. 1 Selects the inverted characters. [Ca[...]

iDP-3410 User’s Manual ESC DC3 n [Function] Printing the message [Code] <1B>H <13>H n [Range] 1 ≤ n ≤ 10 [Function] This command prints a message. If the value of n is specified beyond the range, the message will not be printed.[...]

iDP-3410 User’s Manual ESC DC2 n1 n2 [Function] Deleting the download character, message, bit image [Code] <1B>H <12>H n1 n2 [Range] 0 ≤ n1 ≤ 3 0 ≤ n2 (Specify 0 at n1 = 0) (1 ≤ n2 ≤ 10 at n1 = 1) (32 ≤ n2 ≤ 224 at n1 = 2) (Specify 0 at n1 = 3) [Outline] This command deletes the downloaded characters, message, and bit im[...]

iDP-3410 User’s Manual GS " ∗ " n1 n2 [d] n1 × n2 × 8 [Function] Defining the download, bit image [Code] <1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8 [Range] 1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24 Note) Take care that the number of data(n1 × n2 × 8) is equal to or smaller than 2,048. [Outline] This command defi[...]

iDP-3410 User’s Manual GS ⁄ m [Function] Printing the download, bit image [Code] <1D>H <2F>H m [Range] 0 ≤ m ≤ 255 [Outline] This command prints the bit image saved in the number specified with m. [Caution] If the print buffer contains the data, this command will be ignored. If the bit image has not been saved in the specified n[...]

iDP-3410 User’s Manual 14. CHARACTER CODES TABLE 14.1 CBM (Domestic)[...]

iDP-3410 User’s Manual 14.2 CBM (International)[...]

iDP-3410 User’s Manual 14.3 STAR (Domestic)[...]

iDP-3410 User’s Manual 14.4 STAR (International)[...]

iDP-3410 User’s Manual 14.5 Code Page 437[...]

iDP-3410 User’s Manual 14.6 Katakana[...]

iDP-3410 User’s Manual 14.7 Code Page 850[...]

iDP-3410 User’s Manual 14.8 Code Page 860[...]

iDP-3410 User’s Manual 14.9 Code Page 863[...]

iDP-3410 User’s Manual 14.10Code Page 865[...]

iDP-3410 User’s Manual 14.11Code Page 852[...]

iDP-3410 User’s Manual 14.12Code Page 866[...]

iDP-3410 User’s Manual 14.13Code Page 857[...]

iDP-3410 User’s Manual 14.14Windows Code[...]

iDP-3410 User’s Manual 14.15International Character Codes Table[...]

iDP-3410 User’s Manual APPENDIX 1. BLOCK DIAGRAM ROM RAM OSC16MHz POWER LED ERROR LED FEED Switch Drawer Parallel (CENTRONICS Based) Serial (RS-232C Based) AC Adapter 34 AD Series (26V DC, 1.15A) DIP Switch Driver Interface Reset Driver Driver Filter Power Supply Vp Vcc Print Head Paper End DC Moter Driver Printer Mechanism Vp :For mechanism driv[...]

iDP-3410 User’s Manual APPENDIX 2. OUTLINE DRAWING[...]

iDP-3410 User’s Manual <<<German>>> <VORSICHT> 1. Bitte lesen Sie die Bedienungsanleitung vor dem Betrieb des Geräts aufmerksam durch und bewahren Sie die Anleitung anschließend für späteres Nachschlagen an einem sicheren Platz auf. 2. Änderungen des Inhalts dieser Anleitung bleiben ohne Vorankündigung vorbehalten. 3[...]

iDP-3410 User’s Manual 9. Beachten Sie jedoch, daß wir, ungeachtet des obigen Punkts 8, keinerlei Haftung für negative Folgeerscheinungen im Zusammenhang mit dem Betrieb dieses Geräts übernehmen.[...]

iDP-3410 User’s Manual ZU BEACHTENDE SICHERHEITSMASSREGELN Zur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personen und Sachschäden sind die folgenden Vorsichtsmaßregeln unbedingt zu beachten. _ Der folgende Text beschreibt das Ausmaß der Gefahren und potentiellen Sachschäden, die durch eine Mißachtung der Bedienungshinweise [...]

iDP-3410 User’s Manual WARNUNG _ Bei m Bet rieb des Geräts sind die nachf olgenden Vorsic htsma ßrege ln unbedingt zu beac hten. Eine Mißachtung di eser Hinwe ise kann zu Schäden, Funktionsstörungen, Rauc hentwicklung und Bra ndgef ahr dur ch Überhit zen und zu elektrisc hen Schlägen führen. Der fortgesetzte Betrieb des Geräts in anormal[...]

iDP-3410 User’s Manual VORSICHTSMASSREGELN FÜR DIE AUFSTELLUNG • Das Gerät nicht an Plätzen abstellen oder betreiben, an denen es Feuer, Feuchtigkeit oder direkter Sonnenbestrahlung ausgesetzt ist. Ebenso sind Plätze in der Nähe von Heizkörpern und sonstigen Wärmenquellen zu vermeiden, an denen Umgebungstemperatur und Luftfeuchtigkeit ni[...]

iDP-3410 User’s Manual VORSICHTSMASSREGELN FÜR DIE HANDHABUNG Zur Vermeidung von Problemen sind bei der Handhabung des Geräts die folgenden Vorsichtsmaßregeln zu beachten. • Für die Stromversorgung ausschließlich das vorgeschriebene Netzteil verwenden. • Den Druckbetrieb nicht ohne eingelegtes Papier oder ohne Farbband starten, da hierdu[...]

iDP-3410 User’s Manual TÄGLICHE WARTUNG • Vor der Wartung zuerst den Drucker ausschalten. • Schmutz und Staub mit einem trockenen, weichen Tuch vom Druckergehäuse abwischen. Bei starker Verschmutzung einen Lappen in Wasser anfeuchten, auswringen und damit abwischen. Hierzu niemals flüchtige organische Lösungsmittel, wie z.B. Alkohol, Terp[...]

iDP-3410 User’s Manual am Kabel ziehen. • Durch Ziehen am Netzadapter-Anschlußkabel können Schäden entstehen, die zu Bränden, elektrischen Schlägen oder gebrochenen Kabeldrähte führen. • Bei einem Gewitter sollte das Netzteil von der Steckdose getrennt und der Drucker nicht verwendet werden. Ein Blitzschlag kann Brände und elektrische[...]

iDP-3410 User’s Manual 4.2 Anschluß des Schnittstellenkabels 1. Den Drucker (einschließlich angeschlossene Geräte) ausschalten. 2. Den Kabelstecker korrekt ausgerichtet (Ober- und Unterseite prüfen) an die Schnittstellenbuchse anschließen. 3. Die Kabelstecker befestigen: • Seriellschnittstelle: durch Festziehen der Schrauben sichern. • P[...]

iDP-3410 User’s Manual 4.4 Einsetzen der Farbbandkassette 1. Die Druckerabdeckung aufklappen. 2. Bei schlaffem Farbband den Knopf in Pfeilrichtung drehen, um das Band vor dem Einsetzen der Kassette straff zu wickeln. 3. Die Farbbandkassette zwischen Druckkopfabdeckung und Walze einsetzen und gleichzeitig die Halteklauen in den Halter des Druckers[...]

iDP-3410 User’s Manual 4.5 Einlegen der Papierrolle 1. Mit den Fingern in die Aussparungen an beiden Seiten der Druckerabdeckung greifen, und die Abdeckung durch Anheben bis zum Anschlag öffnen. 2. Das Ende des Druckpapiers in nahezu rechtem Winkel abschneiden. VORSICHT : • Ausschließlich das vorgeschriebene Druckpapier verwenden. • Die Ver[...]

iDP-3410 User’s Manual VORSICHT : • Schlaffes Druckpapier durch Zurückdrehen der Papierrolle straffen. • Bei schräg eingesetztem Druckpapier den Papier-Freigabehebels drücken und das Papier gerade richten. • Die Druckerabdeckung niemals während des Druckens öffnen, da hierdurch Papierstaus entstehen können.[...]

iDP-3410 User’s Manual 4.6 Entfernen des restlichen Druckpapiers 1. Die Druckerabdeckung aufklappen. 2. Den Papier-Freigabehebel in Pfeilrichtung drücken und das Rollenpapier herausziehen. VORSICHT : Beim Herausziehen des Druckpapiers (in Vorwärts- oder Rückwärtsrichtung) darauf achten, den Papier-Freigabehebel zu betätigen. 4.7 Beseitigung [...]

iDP-3410 User’s Manual 4.8 Bedienfeld und Fehleranzeigelämpchen 1. Netzanzeigelämpchen (grün) (POWER) Leuchtet bei eingeschalteter Netzversorgung. 2. Fehleranzeigelämpchen (rot) (ERROR) Leuchtet, wenn das Papier aufgebraucht ist oder ein Fehler im Druckmechanismus oder in der Kommunikations auftritt. <Fehleranzeigen> • Papierende: Wen[...]

iDP-3410 User’s Manual 5. DIP-SCHALTER-EINSTELLUNG 5.1 Lage der DIP-Schalter (1) Betriebsstrom ausschalten. (2) Ein Kassettenband entfernen. Die DIP-Schalter liegen, wie in der Abbildung gezeigt. (Nur DS1 für Parallel- Schnittstelle vorhanden.) ON ON NEIN JA[...]

iDP-3410 User’s Manual 5.2 DIP-Schalter-Einstellungen 1) DIP-Schalter 1 No. Funktion ON OFF Bei Auslieferung ab Werk DS1-1 Automatische Schneideinheit Ja Nein AUS DS1-2 Internationale Zeichen AUS *2 DS1-3 ″ AUS *2 DS1-4 ″ Siehe Tabelle unten AUS *2 DS1-5 Verwendetes Papier 2P 1P AUS DS1-6 CR-Modus Siehe Tabelle unten AUS DS1-7 Stellen 42 Stel[...]

iDP-3410 User’s Manual 2) DIP-Schalter 2 No. Funktion ON OFF Werksseitige Einstellung DS2-1 Bitlänge 8 Bit 7 Bit ON DS2-2 Parität Nein Ja ON DS2-3 Ungerade/Gerade Ungerade Gerade ON DS2-4 Kommunikationsmodus DTR/DSR XON/XOFF ON DS2-5 Baudrate ON DS2-6 ″ ON DS2-7 ″ Siehe Tabelle unten OFF DS2-8 Nicht verwendet − − OFF Baudrate Baudrate D[...]

iDP-3410 User’s Manual 6. EINSTELLUNG DER VORWAHL-JUMPERSTECKER 6.1 Lage der Vorwahl-Jumperstecker (1) Betriebsstrom ausschalten. (2) Ein Kassettenband entfernen. (3) Die Oberabdeckung entfernen. Der Vorwahl-Jumperstecker liegt, wie in der Abbildung unten gezeigt. Serielle Schnittstelle Parallele Schnittstelle 6.2 Vorwahl-Jumperstecker-Tabelle Se[...]

iDP-3410 User’s Manual 12. WARTUNG UND DIENST Bitte wenden Sie sich an die folgenden Stellen für weitergehende Informationen. Nordamerika Andere Gebiete CBM America Corporation Japan CBM Corporation Service Center Information Systems Division 365 Van Ness Way CBM Bldg., 5-68-10, Nakano Suite 510 Nakano-ku, Tokyo 164-0001 Torrance, CA 90501, USA [...]