Dakota Alert CAD-05 Kit GSM manuale d’uso

C AD-05 Kit GSM A uto Dialer Owner ’ s Manual CAD-05 Kit Manual.indd 1 10/15/2009 9:40:53 AM[...]

2 3 War nings : This device complie s w ith Par t 1 5 of the FC C rul es, Oper ation of this d evice is subje ct to the fol - lowing con ditions: 1 . This devi ce may not cause har mful inter fere nce. 2. This d evice must a ccept any interf erence, including inter fe rence that may cause und esired op eration. Featu res : Wirel ess alarm; n o tele[...]

2 3 IMPORT ANT Before you install the PIR Det ec tors, please take these poin ts into consideration: Don ’t position the detectors facing windows. Don ’t position in direct sunlight. Don ’t position above heat sources or in ar eas of moisture. Don ’t let pets roam into the detection area when the system is armed. The PIR Sensor is set to Al[...]

4 5 Installation T ools: Small & Large Phillips Screwdrivers; Small Standard Screwdriver . Set Up: 1. Set PIR and CAD -05 dipswitches to match. The rst ve dipswitches on both units (F igure 1-1 and Figure 2-1) need to be set exactly the same with the last 3 dipswit ches on the PIR sensor (Figur e 1-1) matching the 3 numbers on the sticker[...]

4 5 SIM card is properly installed, you will see a telephone symbol on the display (Figure 4-2). Y ou now have 30 seconds to teach the dialer . Press the RECORD button (Figure 4-3) on the dialer and the display will show “learning 0. ” Press any key on the RF Keyfob . The display will then show “learning 1” followed by a BEEP to conrm th[...]

6 7 Advan ced Op erat ions HOW TO PROG RA M THE AUTO DIALE R *If no key is pre ssed for 30 s econds, th e dialer will autom atically ex it the pro gramming mo de. Notice: The system must be in the OFF mode for a ll programming. How to r ecor d the voi ce mes sage s: Alarm 1 = T amp er and panic al arm. Alarm 2 = PIR se nsors an d hard-w ired input [...]

6 7 1 . Key in the fo ur digit user p assword code (fac tor y de fault is 1 234.) 2. Press PROGR AM > 3 > EN TER. 3. The number you pre ss nex t will selec t the p osition in the sequen ce you want that teleph one numbe r to dial ( 1 = rst numb er called, 2 = second numb er called, and so on) . 4. Press ENTER and key in th e rst tel eph[...]

How to c hang e the u ser pa sswor d code (fac to ry d efau lt is 1 23 4): 1 . Key in the fo ur digit user p assword code (fac tor y de fault 1 234.) 2. Press P ASSWOR D 3. The LCD will change to n -p. 4. Key in your new four di git user pass word code. 5. The LCD will change to c - p. 6. Key in your new fou r digit user pass word code aga in. 7 . [...]

8 9 How to s et Ent r y/Exi t Del ay time s (defaul t bot h del ay set at 30 se cond s): The entr y/ ex it times are the times the Auto D ialer gives you to enter/ exi t th e are a covered by the sys tem be fore i t arms/alarms. Thes e are pre -set to 30 se conds. Y ou c an also change the timing to inst ant or 60 se conds. Entr y D elay: 1 . Key i[...]

10 11 How to d isab le T am per Func ti on (fac tor y set ti ng T amp er ON): 1 . Key in the fo ur digit user p assword code (fac tor y de fault 1 234.) 2. Press PROGR AM > 8 > EN TER 3. Press N (N = 0 without tamper func tion; 1 with t a mper func tion) . Press ENT ER. Quick guid e: Press 1 2 3 4 > PROGR AM > 8 > ENTER > N > E[...]

10 11 How to s top t he Dia ler fr om dia ling t he te lep hon e numb ers in s equ ence : When the Auto Dialer star t s dialing , it wi ll dial th e rs t telep hone number and re peat th e pre -re corded voice m essage for 1 minute. If there is n o resp onse from the pho ne, th en it will hang u p an d d ial the nex t number until all the progra[...]

12 13 How to c hang e the b ack-up b att er y: Impor t ant: It is recomm ended to change the back-up bat ter y at leas t on ce a year , even i f the bat ter y is not low. 1 . Firs t make sure that the Auto Dialer is O FF . T hen releas e it from the w all. 2. Remove the bat ter y d oor and take out the old bat ter y. Inser t new 7 . 2V recharg eabl[...]

12 13 HOW TO RE SET TH E AUTO DIALER Inside the bat tery compartment: Remove the power supply and the A u to Dial er f rom th e wall . Re move the 7 . 2V bat ter y . Then remove the SIM card. Inside the bat ter y compar tme nt is a s witch. Move it to th e ERASE positio n. Conne ct the power to the Auto Dialer then press DELETE twice. T here w ill [...]

14 15 CAD-05 Quick Reference Programming (F or step -by-step progr amming, refer to pages 6-10) Programming: En ter Pass code 1234; push the Pr ogram button; select option number; 1 - Audible Alarm (N = 1-Audible; 0-Silen t) 1234>PR OGRAM>1>ENTER>N>ENTER 2 - Length of Audible A lar m (N = 1-99 Mins) 1234>PROGRAM>2>ENTER>N[...]

14 15 TECH NIC AL SUPPO RT If you e ncounter any dicul ty in the oper ation of this pro duc t af ter read ing th e ma nual, p lease contac t us . Y ou can reach us by ph one at 605-35 6 - 2772 from 8:30 AM t o 5 : 00 P M Monday thro ugh Friday (Central Stand ard Time). We will b e happy to answer yo ur questio ns and help you in any way we can. [...]

Dak ota Aler t, Inc . 32556 E. Main Street P0 Box 130 Elk P oint, SD 57025 Phone: (605) 356-2772 F ax: (605) 356-3662 W eb: ww w .dakotaaler t.com CAD-05 Kit Manual.indd 16 10/15/2009 9:40:53 AM[...]