Denon AVR-1802/882 manuale d’uso

A V SURROUND RECEIVER A VR-1802/882 OPERA TING INSTRUCTIONS MODE D’EMPLOI B 3 0 0 2 6 7 9 8 2 3 6 7 MASTER VOLUME AVR- 1802 PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER VOLUME LEVEL B PHONES CH VOL SURROUND MODE SURROUND PARAMETER ON / STANDBY TONE CONTROL SELECT EXT. IN INPUT MODE A B CINEMA EQ TONE DEFEAT ANALOG SPEAKER AUTO ON / STANDBY DT[...]

2 ENGLISH 2 SAFETY PRECAUTIONS 2 NOTE ON USE / OBSERV A TIONS RELA TIVES A L ’UTILISA TION • Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack. • Eviter des températures élevées. T enir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère. • Handle the power cord [...]

3 SAFETY INSTRUCTIONS 1 . Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to[...]

4 ENGLISH 2 INTRODUCTION 2 ACCESSORIES Thank you for choosing the DENON A/V Surround receiver . This remarkable component has been engineered to provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite m usic sources. As this product is provided with [...]

5 ENGLISH 3 CAUTIONS ON HANDLING 4 FEA TURES • Switching the input function when input jacks are not connected A clicking noise may be produced if the input function is switched when nothing is connected to the input jacks. If this happens, either turn down the MASTER VOLUME control or connect components to the input jacks. • Muting of PRE OUT [...]

6 ENGLISH 5 P AR T NAMES AND FUNCTIONS Front Panel • For details on the functions of these parts, refer to the pages given in parentheses ( ). VOLUME LEVEL PHONES CH VOL SURROUND MODE SURROUND PARAMETER ON / STANDBY TONE CONTROL SELECT EXT. IN INPUT MODE A B CINEMA EQ TONE DEFEAT ANALOG SPEAKER AUTO ON / STANDBY DTS PCM SIGNAL DIGITAL INPUT REMOT[...]

7 ENGLISH Remote control unit • For details on the functions of these parts, refer to the pages given in parentheses ( ). B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNER SHIFT REMOTE CONTROL UNIT RC-897 STATUS MUTING T.TONE MASTER VOL TITLE DISC SKIP+ V. AUX INPUT MODE CDR / TAPE CHANNEL TV CD · MD/CDR · DVD/ VDP VIDEO SELECT SYSTEM S[...]

8 ENGLISH 6 READ THIS FIRST This A V Surround Receiver must be setup before use. Following these steps. 2 Speaker system layout Basic system layout • The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor: Subwoofer Center speaker system Surround speaker systems Front speaker system[...]

9 ENGLISH 8 CONNECTIONS • Do not plug in the power cord until all connections have been completed. • Be sure to connect the left and right channels properly (left with left, right with right). • Insert the plugs securely . Incomplete connections will result in the generation of noise. • Use the AC OUTLETS for audio equipment only . Do not u[...]

10 ENGLISH CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 FRONT FRONT PREOUT CENTER CENTER DVD/ VDP TV/ DBS VCR-1 VCR-2 S-VIDEO VCR-1 VCR-2 MONITOR SUB WOOFER SPEAKER SYSTEMS AC OUTLETS SURROUND AC 120V 60Hz SWITCHED TOTAL 120W(1A.)MAX. PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 FL[...]

11 ENGLISH CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 FL AM ANTENNA TERMINALS LOOP ANT. FM COAX. 75 SL EXT. IN AUDIO DIGITAL VIDEO C FR SR SW COAX. R OUT VIDEO OUT L AUDIO OUT COAXIAL DIGITAL R OUT VIDEO OPTICAL OUT L AUDIO OUT DIGITAL[...]

12 ENGLISH Connecting a video component equipped with S-video jacks • When marking connections, also refer to the operating instructions of the other components. • A note on the S input jacks The input selectors for the S inputs and pin jack inputs work in conjunction with each other . • Precaution when using S-jacks This unit ’ s S-jacks ([...]

13 ENGLISH 1 4 2 3 Connecting the antenna terminals CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 FL AM ANTENNA TERMINALS LOOP ANT. FM COAX. 75 SL EXT. IN AUDIO DIGITAL VIDEO C FR SR SW COAX. DIRECTION OF BROADCASTING ST A TION AM LOOP AN[...]

14 ENGLISH Speaker system connections • Connect the speaker terminals with the speakers making sure that like polarities are matched ( < with < , > with > ). Mismatching of polarities will result in weak central sound, unclear orientation of the various instruments, and the sense of direction of the stereo being impaired. • When mak[...]

15 ENGLISH Protector circuit • This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when the temperature surrounding the unit becomes unusually high, or when t[...]

16 ENGLISH 9 USING THE REMOTE CONTROL UNIT Following the procedure outlined below , insert the batteries before using the remote control unit. Range of operation of the remote control unit Inserting the batteries B B Point the remote control unit at the remote control sensor as shown on the diagram at the left. NOTES: • The remote control unit ca[...]

17 ENGLISH 10 SETTING UP THE SYSTEM • Once all connections with other A V components have been completed as described in “ CONNECTIONS ” (see pages 9 to 15), make the various settings described below on the display . These settings are required to set up the listening room ’ s A V system centered around the this unit. STATUS MUTING T.TONE M[...]

18 ENGLISH Before setting up the system 1 2 Press the SYSTEM button to enter the setting. Check that all the components are correct, then press the POWER operation switch on the main unit or the POWER button on the remote control unit to turn on the power . 3 Press the SELECT or (down) button to switch to the speaker configuration set up. *SYSTEM S[...]

19 ENGLISH NOTE: • When “ Small ” has been selected for the front speakers, “ Large ” cannot be selected for the surround speakers. 4 Use the (left) and (right) buttons to select your subwoofer setting. 4 S.WOOFER YES YES NO (left) button (right) button Press the SELECT or (down) button to enter the settings and switch to the SUBWOOFER MO[...]

20 ENGLISH Setting the delay time Input the distances from the listening position to the speakers and set the surround delay time. Preparations: Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right). L 1 : Distance from center speaker to listening position L 2 : Distance from front speakers to list[...]

21 ENGLISH Digital input setup Input the type of components connected to the digital input terminals. 1 Use the (left) and (right) buttons to set the type of device connected to the COAXIAL input (COAXIAL) terminal. 9 COAX DVD CD DVD TV VCR1 VCR2 CDR OFF • Select “ OFF ” if nothing is connected. Press the SELECT or (down) button to switch the[...]

22 ENGLISH NOTE: • The memory can only be preset for either the MD or the CDR. Preset codes set upon shipment from the factory and when reset. Operating DENON audio components DENON remote-controllable audio components can be controlled using this unit ’ s remote control unit. Note that some components, however , cannot be operated with this re[...]

23 ENGLISH Preset memory (Video component) DENON and other makes of components can be operated by setting the preset memory for your make of video component. This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown on the List of P[...]

24 ENGLISH Operating a video component stored in the preset memory 1 Set the slide switch to “ VIDEO ” . AUDIO CD MD/CDR VIDEO 2 Operate the video component. • For details, refer to the component ’ s operating instructions. Some models cannot be operated with this remote control unit. B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNE[...]

25 ENGLISH 12 OPERA TION Before operating Preparations: Check that all connections are proper . 1 T urn on the power . Press ON/ST ANDBY on the main unit or the A VR/A VC on the remote control unit to turn on the power 2 Select the front speakers. Press SPEAKER A or B turn the speaker on. (Main unit) (Remote control unit) DVD/VDP CD TV/DBS VCR-1 VC[...]

26 ENGLISH Playing the input source B 2 3 1 5 1 Press the button for the program source to be played. EX 1: CD CD 2 (Main unit) (Remote control unit) 2 Select the input mode. T o select the input mode from main unit. • Selecting the analog mode. Press ANALOG to switch to the analog input. (Main unit) • Selecting the external input (EXT . IN) mo[...]

• T o increase the bass or treble: T urn the control clockwise. (The bass or treble sound can be increased to up to +12 dB in steps of 2 dB.) • T o decrease the bass or treble: T urn the control counterclockwise. (The bass or treble sound can be decreased to up to – 12 dB in steps of 2 dB.) T o select the surround mode while adjusting the sur[...]

Using the dimmer function • Use this to change the brightness of the display . The display brightness changes in four steps (bright, medium, dim and off) by pressing the main unit ’ s DIMMER repeatedly . The brightness changes in 3 steps each time the button is pressed, and finally the display turns off. Front panel display • Descriptions of [...]

29 ENGLISH Set the external input (EXT . IN) mode. Press the EXT . IN to switch the external input. Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left), and SR (surround right) channels of the EXT . IN jacks are output directly to the front (left and right), center , surround ([...]

30 ENGLISH 13 SURROUND Before playing with the surround function • Before playing with the surround function, be sure to use the test tones to adjust the playback level from each speakers. This adjustment can be performed from the remote control unit, as described below . • The adjustment with the test tones is only effective in the DOLBY/DTS S[...]

31 ENGLISH Dolby Surround Pro Logic II mode 2 Select the Dolby Surround Pro Logic II mode. SURROUND MODE Light (Main unit) (Remote control unit) 3 Play a program source with the mark. • For operating instructions, refer to the manuals of the respective components. B 2, 5, 7 4. 6 1 2 B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNER SHIFT [...]

32 ENGLISH NOTE: • When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and the setting will be completed. Surround parameters q Pro Logic II Mode: The Cinema mode is the standard required mode for all A / V systems. The Music mode is recommended as the standard mode fo[...]

33 ENGLISH Dolby Digital mode (only with digital input) and DTS Surround (only with digital input) 1 Select the input source. q Select an input source set to digital (COAXIAL/OPTICAL) (see page 21). 8 (Main unit) (Remote control unit) w Set the input mode to “ AUTO ” or DTS. 2 Select the Dolby/DTS Surround mode. SURROUND MODE (Remote control un[...]

34 ENGLISH 5 Use (left) and (right) buttons to set the D. COMP . D.COMP. OFF OFF LOW MID HIGH Press SURROUND or (down) button to switch to the LFE setting. MENU SURROUND (left) button (right) button (Remote control unit) (Remote control unit) 6 Use (left) and (right) buttons to set the LFE level. LFE 0dB • The level can be adjusted in units of 1 [...]

35 ENGLISH 14 DSP SURROUND SIMULA TION • This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetica lly recreate the sound field. One of 7 preset surround modes can be selected according to the program source and the parameters can be adjusted according to the conditions in the [...]

36 ENGLISH DSP surround simulation 1 Select the surround mode for the input channel. SURROUND MODE (Remote control unit) The surround mode switches in the following order each time the SURROUND MODE button is pressed: B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNER SHIFT REMOTE CONTROL UNIT RC-897 STATUS MUTING T.TONE MASTER VOL TITLE DIS[...]

37 ENGLISH Use the (left) and (right) buttons to set the delay time. DELAY 30ms 110ms 30ms 0ms (left) button (right) button (Remote control unit) (3) DELA Y TIME (Remote control unit) (4) DEF AUL T T o reset the settings to the factory defaults, use the (left) and (right) buttons to display “ Ye s ” . DEFAULT Y/N YES NO (left) button (right) bu[...]

38 ENGLISH 1 T urn the SELECT knob to select the surround mode. SELECT (Main unit) • When turned clockwise 2 Press SURROUND P ARAMETER. Press and hold in the surround parameter button to select the parameter you want to set. • The parameters which can be set differ for the different surround modes. (Refer to “ Surround Modes and Parameters ?[...]

39 ENGLISH Surround parameters e ROOM SIZE: This sets the size of the sound field. There are five settings: “ small ” , “ med.s ” (medium-small), “ medium ” , “ med.l ” (medium-large) and “ large ” . “ small ” recreates a small sound field, “ large ” a large sound field. EFFECT LEVEL: This sets the strength of the surrou[...]

40 ENGLISH 15 LISTENING TO THE RADIO Auto preset memory 1 When the main unit ’ s power operation switch turn on while pressing the set ’ s MEMORY button the unit automatically begins searching for FM broadcast stations. 2 When the first FM broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations[...]

41 ENGLISH Press TUNING UP or DOWN button to tune in the desired station. Auto tuning 1 Press TUNER to set the input function to “ TUNER ” . 2 Watching the display , press BAND to select the desired band (AM or FM). 3 Press MODE to set the auto tuning mode. Lit 4 Press TUNING UP or DOWN. • Automatic searching begins, then stops when a station[...]

42 ENGLISH Preset stations 1 Press MEMORY button. 2 Press SHIFT button and select the desired memory block (A to E). SHIFT (Main unit) (Remote control unit) 3 Press PRESET UP or DOWN button to select the desired preset channel (1 to 8). CHANNEL (Main unit) (Remote control unit) 4 Press MEMORY button again to store the station in the preset memory .[...]

43 ENGLISH 16 LAST FUNCTION MEMORY • This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off. • The unit is also equipped with a back-up memory . This function provides approximately one week of memory storage when the main unit ’ s power [...]

44 ENGLISH 18 ADDITIONAL INFORMA TION • Set the front speakers, center speaker and subwoofer in the same positions as in example (1). • Set the surround speakers directly at the sides of the listening position and 60 to 90 centimeters (2 to 3 feet) above ear level. • The signals from the surround channels reflect off the walls as shown on the[...]

45 ENGLISH 2 Dolby Digital and Dolby Pro Logic Comparison of home surround systems No. recorded channels (elements) No. playback channels Playback channels (max.) Audio processing High frequency playback limit of surround channel Dolby Digital 5.1 ch 5.1 ch L, R, C, SL, SR, SW Digital discrete processing Dolby Digital (AC-3) encoding/decoding 20 kH[...]

46 ENGLISH DTS Digital Surround Digital Theater Surround (also called simply DTS) is a multi-channel digital signal format developed by Digital Theater Systems . DTS offers the same “ 5.1 ” playback channels as Dolby Digital (front left, front right and center , surround left and surround right) as well as the stereo 2-channel mode. The signals[...]

47 ENGLISH 19 TROUBLESHOOTING If a problem should arise,first check the following. 1. Are the connections correct ? 2. Have you operated the receiver according to the Operating Instructions ? 3. Are the speakers, turntable and other components operating property ? If this unit is not operating properly , check the items listed in the table below . [...]

48 ENGLISH 20 SPECIFICA TIONS 2 Audio section • Power amplifier Rated output: Front: 80 W + 80 W (8 Ω /ohms, 20 Hz ~ 20 kHz with 0.08% T .H.D.) 115 W + 115W (6 Ω /ohms, 1 kHz with 0.7% T .H.D.) Center: 80 W (8 Ω /ohms, 20 Hz ~ 20 kHz with 0.08% T .H.D.) 115 W (6 Ω /ohms, 1 kHz with 0.7% T .H.D.) Surround: 80 W + 80 W (8 Ω /ohms, 20 Hz ~[...]

49 FRANCAIS 2 INTRODUCTION 2 ACCESSOIRES Nous vous remercions d‘avoir choisi l’ampli-tuner A/V Surround de DENON. Ce remarquable composant a été fabriqué pour fournir une superbe écoute de sons d’ambiance avec des sources de cinéma domestiqu e telles que DVD, ainsi que pour assurer une formidable reproduction haute fidélité de vos sour[...]

50 FRANCAIS 3 PRECAUTIONS DE MANIPULA TION 4 CARACTERISTIQUES • Commutation de la fonction d’entrée lorsque les prises d’entrée ne sont pas connectées Un déclic peut être produit si la fonction d’entrée est commutée lorsque rien n’est connecté aux prises d’entrée. Dans ce cas, abaisser la commande MASTER VOLUME (volume de la ga[...]

51 FRANCAIS 5 NOMENCLA TURE ET FONCTIONS Panneau avant • Pour les détails sur les fonctions de ces pièces, se reporter aux pages données entre parenthèses ( ). VOLUME LEVEL PHONES CH VOL SURROUND MODE SURROUND PARAMETER ON / STANDBY TONE CONTROL SELECT EXT. IN INPUT MODE A B CINEMA EQ TONE DEFEAT ANALOG SPEAKER AUTO ON / STANDBY DTS PCM SIGNA[...]

52 FRANCAIS Unité de télécommande • Pour les détails sur les fonctions de ces pièces, se reporter aux pages données entre parenthèses ( ). B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNER SHIFT REMOTE CONTROL UNIT RC-897 STATUS MUTING T.TONE MASTER VOL TITLE DISC SKIP+ V. AUX INPUT MODE CDR / TAPE CHANNEL TV CD·MD/CDR· DVD/ VDP [...]

53 FRANCAIS 6 A LIRE EN PREMIER Ce récepteur d’ambiance A V doit être réglé avant l’utilisation selon les étapes suivantes. 2 Disposition du système d’enceintes Disposition de base du système • Ce qui suit est un exemple de la disposition de base pour un système comprenant six systèmes d’enceinte et un moniteur de téléviseur: S[...]

54 FRANCAIS 8 CONNEXIONS Connexion des composants audio CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 FRONT FRONT PREOUT CENTER CENTER DVD/ VDP TV/ DBS VCR-1 VCR-2 S-VIDEO VCR-1 VCR-2 MONITOR SUB WOOFER SPEAKER SYSTEMS AC OUTLETS SURROUND AC 120V 60Hz SWITCHED TOTAL 120W(1A.)MAX. PHONO CD SIGNAL GND M[...]

55 FRANCAIS CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 FRONT FRONT PREOUT CENTER CENTER DVD/ VDP TV/ DBS VCR-1 VCR-2 S-VIDEO VCR-1 VCR-2 MONITOR SUB WOOFER SPEAKER SYSTEMS AC OUTLETS SURROUND AC 120V 60Hz SWITCHED TOTAL 120W(1A.)MAX. PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 F[...]

56 FRANCAIS CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 FL AM ANTENNA TERMINALS LOOP ANT. FM COAX. 75 SL EXT. IN AUDIO DIGITAL VIDEO C FR SR SW COAX. R OUT VIDEO OUT L AUDIO OUT COAXIAL DIGITAL R OUT VIDEO OPTICAL OUT L AUDIO OUT DIGITA[...]

57 FRANCAIS Connexion d ’ un composant vid é o é quip é de prises vid é o S • Lors des connexions, se reporter é galement aux instructions d ’ utilisation des autres composants. • Remarque à propos des prises en S Les s é lecteurs d ’ entr é e pour les entr é es en S et les entr é es des prises à broches fonctionnent conjointem[...]

58 FRANCAIS 1 4 2 3 Connexion des bornes d ’ antennes CDR / TAPE CDR / TAPE DVD / VDP TV / DBS DVD / VDP TV / DBS VCR -1 VCR -2 VCR -1 VCR -2 VCR-1 PHONO CD SIGNAL GND MONITOR VCR-2 VCR-1 VCR-2 OPT-2 OPT-2 OPT-1 FL AM ANTENNA TERMINALS LOOP ANT. FM COAX. 75 SL EXT. IN AUDIO DIGITAL VIDEO C FR SR SW COAX. DIRECTION DE ST A TION DE RADIODIFFUSION A[...]

59 FRANCAIS Connexions du syst è me d ’ enceintes Connexion des bornes d ’ enceinte 1. T ourner dans le sens contraire des aiguilles d ’ une montre pour la desserrer . 2. Ins é rer le cordon. 3. T ourner dans le sens des aiguilles d ’ une montre pour la resserrer . Connexion des fiches bananes T ourner dans le sens des aiguilles d ’ une[...]

60 FRANCAIS Circuit de protection • Cet appareil est é quip é d ’ un circuit de protection haute vitesse. Le but de ce circuit est de prot é ger les enceintes contre des situations telles que lorsque la sortie de l ’ amplificateur de puissance est accidentellement court-circuit é e et qu ’ un fort courant passe, lorsque la temp é ratur[...]

61 FRANCAIS 9 UTILISA TION DE LA T É L É COMMANDE En suivant la proc é dure expliqu é e ci-dessous, ins é rer les piles avant d ’ utiliser la t é l é commande. Plage d ’ utilisation de la t é l é commande Insertion des piles B B Diriger la t é l é commande vers le d é tecteur de t é l é commande de la mani è re indiqu é e sur le[...]

62 FRANCAIS 10 INST ALLA TION DU SYSTEME • Une fois que toutes les connexions avec les autres composants A V ont é t é faites comme indiqu é dans “ CONNEXIONS ” (voir pages 54 à 60), faire les diff é rents r é glages d é crits ci-dessous sur l ’ affichage. Ces r é glages sont n é cessaires pour configurer le syst è me de chambre d[...]

63 FRANCAIS A vant de configurer le syst è me 1 2 Appuyer sur la touche SYSTEM pour acc é der aux r é glages. V é rifier que tous les composants sont en bon é tat, puis appuyez sur l ’ interrupteur de mise en marche POWER sur l ’ unit é principale ou la touche POWER sur la t é l é commande pour allumer l ’ alimentation. 3 Appuyer sur [...]

64 FRANCAIS REMARQUE: • Lorsque l ’ option “ Small ” (petit) a é t é s é lectionn é e pour les haut-parleurs avants, l ’ option “ Large ” (grand) ne peut pas ê tre s é lectionn é e pour les haut-parleurs centraux. 4 Utiliser les touches (gauche) et (droit) pour s é lectionner le type de subwoofer install é . 4 S.WOOFER YES YE[...]

65 FRANCAIS Reglage de la temps de retard Entrer les distances de la postion d ’é coute aux enceintes, et r é gler le temps de retard d ’ ambiance. Pr é parations: Mesurer les distances de la position d ’é coute aux enceinte (L1 à L3 sur le diagramme de droite.) L 1 : Distance de l ’ enceinte centrale à la position d ’é coute L 2 :[...]

66 FRANCAIS Configuration de l ’ entr é e num é rique S é lectionner le type d ’ appareil connect é aux bornes de l ’ entr é e num é rique. 1 Utiliser les touches (gauche) et (droit) pour s é lectionner le type d ’ appareil connect é aux bornes de l ’ entr é e coaxiale (COAXIAL). 9 COAX DVD CD DVD TV VCR1 VCR2 CDR OFF • S é le[...]

67 FRANCAIS REMARQUE: • La m é moire ne peut ê tre pr é r é gl é e que pour le MD ou le CDR. Codes pr é r é gl é s r é gl é s à la livraison de l ’ usine et lorsque r é initialis é s. Utilisation des composants audio DENON Les composants audio t é l é commandables DENON peuvent ê tre contr ô l é s en utilisant la t é l é com[...]

68 FRANCAIS M é moire pr é r é gl é e (Composants vid é o) DENON et d ’ autres fabricants de composants peuvent ê tre actionn é s en r é glant la m é moire pr é r é gl é e de votre fabricant de composant vid é o. La t é l é commande peut ê tre utilis é e pour faire fonctionner les composants d ’ autres marques sans utiliser la [...]

69 FRANCAIS Utilisation d ’ un composant vid é o sauvegard é dans la m é moire pr é r é gl é e 1 Placer le commutateur coulissant sur la position “ VIDEO ” . AUDIO CD MD/CDR VIDEO 2 Actionner le composant vid é o. • Pour les d é tails, se reporter aux instructions d ’ utilisation du composant. Certains mod è les ne peuvent pas ê[...]

70 FRANCAIS 12 OPERA TION A vant l ’ utilisation Pr é paratifs: V é rifier que toutes les connexions sont bonnes. 1 Allumer l ’ alimentation. Appuyer l ’ interrupteur de mise en marche (touche). 2 S é lectionner les enceintes avant. Appuyer sur le commutateur d ‘ enceinte A ou B pour activer l ’ enceinte. (Unit é principale) (Unit é [...]

71 FRANCAIS Lecture de la source de programme analogique B 2 3 1 5 1 Appuyer sur la touche de la source de programme à reproduire. Exemple 1: CD CD 2 (Unit é principale) (Unit é de t é l é commande) 2 S é lectionner le mode d ’ entr é e. Pour s é lectionner le mode d ’ entr é e partir de l ’ unit é principale. • S é lection du mo[...]

72 FRANCAIS • Pour augmenter les graves ou les aigu ë s: T ourner la commande dans le sens des aiguilles d ’ une montre. (Le son de graves ou d ’ aigu ë s peut ê tre augment é jusqu ’à +12 dB en é tapes de 2 dB.) • Pour diminuer les graves ou les aigu ë s: T ourner la commande dans le sens des aiguilles d ’ une montre. (Le son de[...]

73 FRANCAIS Utilisation de la fonction de r é duction d ’ intensit é d ’é clairage • Utiliser cette fonction pour modifier la luminosit é de l ’ affichage. La luminosit é de l ’ affichage change en quatre paliers (clair , moyen, sombre et é teint) en appuyant sur la touche DIMMER de la principale. La luminosit é change en 3 é tape[...]

74 FRANCAIS Passer au mode d ’ entr é e externe (EXT . IN). Appuyer sur EXT . IN pour changer l ’ entr é e externe. Une fois cette s é lection effectu é e, les signaux d ’ entr é e, connect é s aux canaux FL (avant gauche), FR (arri è re droit), C (central), SL (surround gauche) et SR (surround droit) des jacks EXT .IN, sont envoy é s[...]

75 FRANCAIS 13 AMBIANCE A vant la lecture utilisant la fonction d ’ ambiance • A vant d ’ effectuer une lecture avec la fonction d ’ ambiance sonore, s ’ assurer d ’ utiliser auparavant les tonalit é s de test pour ajuster les r é glages niveaux de reproduction de chacune des enceintes. Ce r é glage peut ê tre effectu é à partir d[...]

76 FRANCAIS Mode Dolby Surround Pro Logic II 2 S é lectionner le mode Dolby Surround Pro Logic II . SURROUND MODE S ’ allume (Unit é principale) (Unit é de t é l é commande) 3 Reproduire une source programme avec la marque . • Pour les instructions d ’ utilisation, se reporter aux manuels des composants respectifs. B 2, 5, 7 4. 6 1 2 B D[...]

77 FRANCAIS 7 R é gler les param é trages d'ambiance sonore. • R é glage CINEMA EQ ON OFF ou ou SELECT SELECT CINEMA EQ OFF • R é glage P ANORAMA ON OFF ou ou SELECT SELECT PANORAMA OFF • R é glage DIMENSION 0 3 6 ou ou SELECT SELECT DIMENSION 3 • R é glage CENTER WIDTH 0 CENTER WIDTH O 4 7 ou ou SELECT SELECT • R é glage DEF [...]

78 FRANCAIS Mode Dolby Digital (uniquement avec entr é e num é rique) et le mode d ’ ambiance DTS (uniquement avec entr é e num é rique) 1 S é lectionner la source d ’ entr é e. q S é lectionner une source d ’ entr é e r é gl é e à num é rique (COAXIAL/OPTICAL) (voir page 66). 8 (Unit é principale) (Unit é de t é l é commande)[...]

79 FRANCAIS 5 Utiliser les touches (gauche) et (droit) pour r é gler la compression de la gamme dynamique (D.COMP). D.COMP. OFF OFF LOW MID HIGH Appuyer sur la touche SURROUND ou (bas) pour passer au r é glage LFE. MENU SURROUND touche (gauche) touche (droit) (Unit é de t é l é commande) (Unit é de t é l é commande) 6 Utiliser les touches ([...]

80 FRANCAIS 14 SIMULA TION D ’ AMBIANCE DSP • Ce appareil est é quip é d ’ un DSP (processeur num é rique de signal) de haute pr é cision qui utilise le traitement des signaux num é riques pour recr é er de mani è re synth é tique le champ sonore. Un des 7 modes d ’ ambiance pr é r é gl é s peut ê tre s é lectionn é en fonctio[...]

81 FRANCAIS Simulation d ’ ambiance DSP 1 S é lectionner le mode d ’ ambiance pour le canal d ’ entr é e. SURROUND MODE (Unit é de t é l é commande) Le mode d ’ ambiance commute dans l ’ ordre suivant chaque fois que la touche SURROUND MODE est enfonc é e: B DVD/VDP CD PHONO TV/DBS VCR-1 VCR-2 SURROUND MODE TUNER SHIFT REMOTE CONTRO[...]

82 FRANCAIS Utiliser les touches (gauche) et (droit) pour r é gler le d é lai. DELAY 30ms 110ms 30ms 0ms touche (gauche) touche (droit) (Unit é de t é l é commande) (3) DELA Y TIME (Unit é de t é l é commande) (4) DEF AUL T Pour remettre le syst è me en configuration par d é faut, utiliser les touches (gauche) et (droit) pour que “ Ye s[...]

83 FRANCAIS 1 T ourner le bouton SELECT pour s é lectionner le mode surround. SELECT (Unit é principale) • Lorsqu ’ il est tourn é dans le sens horaire 2 Appuyer sur la touche SURROUND P ARAMETER. Appuyer sur la touche de param è tre d ’ ambiance et la maintenir enfonc é e pour s é lectionner le param è tre à d é finir . • Les para[...]

84 FRANCAIS Param è tres d ’ ambiance e ROOM SIZE (T aille de piece): Ceci r è gle la taille du champ sonore. Il y a cinq r é glages: “ small ” (petit), “ med.s ” (moyen – petit), “ medium ” (moyen), “ med.l ” (moyen – large) et “ large ” . “ small ” recr é e un petit champ sonore, “ large ” un large champ sono[...]

85 FRANCAIS 15 ECOUTER DE LA RADIO M é moire pr é r é gl é e automatique 1 Lorsque l ’ interrupteur d ’ alimentation de l ’ appareil principal est activ é en m ê me temps que le touche de r é glage MEMORY , l ’ appareil commence automatiquement à chercher des station de radio FM. 2 Lorsque la premi è re station de radiodiffusion en[...]

86 FRANCAIS Appuyer sur la touche TUNING UP (augmentation de syntonisation) ou TUNING DOWN (diminution de syntonisation) pour syntoniser la station d é sir é e. Syntonisation automatique 1 R é gler la fonction d ’ entr é e à “ TUNER ” . 2 En regardant l ’ affichage, appuyer sur la touche BAND (bande) pour s é lectionner la bande d é [...]

87 FRANCAIS Stations pr é r é gl é e 2 Appuyer sur la touche SHIFT , et s é lectionner le bloc de m é moire d é sir é (A à E). SHIFT (Unit é principale) (Unit é de t é l é commande) 3 Appuyer sur la touche PRESET UP (augmentation de pr é r é glage) ou PRESET DOWN (diminution de pr é r é glage) pour s é lectionner le canal pr é r ?[...]

88 FRANCAIS 16 MEMOIRE DE DERNIERE FONCTION • Cet appareil est é quip é d ’ une m é moire de derni è re fonction qui stocke les conditions des r é glages d ’ entr é e et de sortie telles qu ’ elles é taient imm é diatement apr è s la mise hors tension. • L ’ appareil est é galement é quip é d ’ une m é moire de sauvegarde[...]

89 FRANCAIS 18 INFORMA TIONS SUPPLEMENT AIRES • Placer les enceintes avant, l ’ enceinte centrale et le subwoofer aux m ê mes positions que dans l ’ exemple (1). • Placer les enceintes d ’ ambiance directement au niveau des c ô t é s de la position d ’é coute et de 60 à 90 cm (2 à 3 pieds) au- dessus du niveau des oreilles. • Le[...]

90 FRANCAIS 2 Dolby Digital et Dolby Pro Logic Comparaison de syst è mes d ’ ambiance domestiques Nbre. de canaux enregistr é s ( é l é ments) Nbre. de canaux de lecture Canaux de lecture (max.) T raitement audio Limite de reproduction haute fr é quence de canal d ’ ambiance Dolby Digital 5.1 ch 5.1 ch L, R, C, SL, SR, SW T raitement num ?[...]

91 FRANCAIS DTS Digital Surround Digital Theater Surround ( é galement appel é simplement DTS) est un format de signaux num é riques de canaux multiples d é velopp é par Digital Theater Systems. DTS offre les m ê mes canaux de lecture “ 5.1 ” que Dolby Digital (avant gauche, avant droit et central, gauche et droit d ’ ambiance) ainsi qu[...]

92 FRANCAIS 19 DEPIST AGE DES P ANNES Si un probl è me se produit, v é rifier d ’ abord les points suivants: 1. Les connexions sont-elles correctes ? 2. L ’ ampli-tuner a-t-il é t é utilis é conform é ment au mode d ’ emploi ? 3. Les enceintes, la platine tourne-disque et les autres appareils fonctionnent-ils correctement ? Si cet appar[...]

93 FRANCAIS 20 SPECIFICA TIONS 2 Section audio • Amplificateur de puissance Puissance de sortie nominale: A vant: 80 W + 80 W (8 Ω /ohms, 20 Hz ~ 20 kHz avec D.H.T . de 0,08%) 115 W + 115 W (6 Ω /ohms, 1 kHz avec D.H.T . de 0,7%) Central: 80 W (8 Ω /ohms, 20 Hz ~ 20 kHz avec D.H.T . de 0,08%) 115 W (6 Ω /ohms, 1 kHz avec D.H.T . de 0,7%) [...]

94 LIST OF PRESET CODES / LISTE DE CODES PR É R É GL É S ENGLISH FRANCIAS DVD Denon *[11] , 12 Hitachi 14 JVC 17 Onkyo 13, 15, 16 Panasonic 12, 18 Philips 24 Pioneer 19, 20, 21 RCA 23 Samsung 22 Sony 25 T oshiba 13 Y amaha 12, 26 VDP Denon 01, 02, 03 Magnavox 05 Mitsubishi 02 Panasonic 03 Philips 05 Pioneer 02 RCA 02 Sony 04 VCR Admiral 10 Aiwa [...]

95 ENGLISH FRANCIAS T atung 07, 09 T eac 07, 09, 12 T echnics 04, 21 T elefunken 54, 55 Thorn 08, 11 T oshiba 24, 41, 59 Universum 11, 20, 54 W . WHouse 11 Wards 10, 11, 25, 42 Y amaha 06, 07, 08, 09 TV Admiral 06, 07 Aiwa 08 Akai 09, 10 Alba 10 AOC 03 Bell & Howell 06 Bestar 11 Blaupunkt 12, 13 Blue sky 11 Brandt 14 Brocsonic 03 Bush 10 Clatro[...]

14-14, AKASAKA 4-CHOME, MINA TO-KU, TOKYO 107-8011, JAP AN T elephone: (03) 3584-8111 Printed in Korea 511 3800 105[...]