Denon AVR-391 manuale d’uso

D&M Holdings Inc. SER VICE MANUAL e e Copyright 2010 D&M Holdings Inc. All rights reserved. W ARNING: Violators will be prosecuted to the maximum extent possible. MODEL JP E3 E3B E2 EK EA E1 E1C A VR-1311 33 A VR-391 33 A V SURROUND RECEIVER MODEL JP E3 E3B E2 EK EA E1 E1C DHT -1311XP 3 DHT -391XP 33 3 5.1CH HOME THEA TER SYSTEM Ve r . 3 ?[...]

2 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer , make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the r[...]

3 NOTE FOR SCHEMA TIC DIAGRAM W ARNING: Parts marked with this symbol z have critical characteristics. Use ONL Y replacement parts recommended by the manufacture r. CAUTION: Before returning the unit to the customer , make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 [...]

4 TECHNICAL SPECIFICA TIONS n Audio Section • Power amplifi er Rated output : Front : 75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.) 110 W + 110 W (6 Ω, 1 kHz with 0.7 % T.H.D.) Center : 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.) 110 W (6 Ω, 1 kHz with 0.7 % T.H.D.) Surround : 75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.[...]

5 245.0 43.5 30.0 30.5 20.0 20.7 22.2 86.0 340.0 166.5 146.5 43.5 381.4 338.5 248.0 435.0 DIMENSION The illustration is A VR-131 1 model.[...]

6 CAUTION IN SER VICING Initializing A V SURROUND RECEIVER A V SURROUND RECEIVER initialization should be performed when the μ com, peripheral parts of μ com, and Digital P .W .B. are replaced. 1. T urn off the power using ON/ST ANDBY button. 2. Press ON/ST ANDBY button while simultaneously pressing SURROUND MODE 0 and SURROUND MODE 1 buttons. 3.[...]

7 DISASSEMBL Y • Disassemble in order of the arrow of the fi gure of following fl ow . • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow . • In the case of the re-assembling, observe "attention of assembling" it. • If wire bundles are untied or moved to perform adjustment or parts re[...]

8 1. FRONT P ANEL ASSY (1) Remove the screws. (2) Cut the wire clamp band, then disconnect the connector wires and FFC cable. Remove the screws. (3) Remove the screws. TOP  COVER FRONT PANEL ASSY → Proceeding : View from bottom CN209 CN71 FFC cable CN44 cut cut FRONT P ANEL ASSY WIRE SUPPORT UNIT Please refer to "EXPLODED VIEW" for t[...]

9 2. HDMI UNIT (1) Remove the screws. (2) Disconnect the connector wire and FFC cable. TOP  COVER HDMI UNIT → Proceeding : Direction of photograph: A CN12 FFC cable HDMI UNIT[...]

10 3. INPUT UNIT (1) Remove the screws. (2) Disconnect the connector wires and FFC cables, then remove the screws. TOP  COVER HDMI UNIT → INPUT UNIT → Proceeding : Direction of photograph: A CN42 CN71 CN43 FFC cable FFC cable INPUT UNIT[...]

11 4. RADIA TOR ASSY (1) Remove the screws. (2) Disconnect the connector wires, then remove the screws. TOP  COVER HDMI UNIT → INPUT UNIT → RADIATOR ASSY → Proceeding : Direction of photograph: A RADIA TOR ASSY CN71 CN44 CN45 CN41 CN47 CN48 CN46[...]

12 (3) Remove the RADIA TOR ASSY from the main unit. 5. POWER UNIT 6. POWER TRANS Direction of photograph: C Please refer to "EXPLODED VIEW" for the disassembly method of each P .W .B included in RADIA TOR ASSY . TOP  COVER POWER UNIT → Proceeding : Please refer to "EXPLODED VIEW" for the disassembly method of POWER UNIT . [...]

13 SPECIAL MODE Special mode setting button b Press the ON/ST ANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents μ com/DSP V ersion display mode ST A TUS DIMMER Firmware versions such as Main, DSP are displayed in the FL display . Errors are displayed when they occur . (Refer to page 14.) [...]

14 1. μ com/DSP V ersion display mode 1.1. Operation speci fi cations μ com/DSP version display mode: When started up, the version information is displayed. Starting up: With the "DIMMER" and "ST A TUS" buttons pressed, press the "ON/ST ANDBY" button to turn the power on. Now , press the "ST A TUS" button [...]

15 ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, conrm contents of the following. PWB Name Ref . No. Desc ript ion Afte r repl aced R emark DIGIT AL IC91 T5CN5 B SOFTW ARE: Main DIGIT AL IC82 ST25VF080B-50-4C-S2AF B SOFTW ARE: DSP ROM After replaced A : Mask ROM (With software). No [...]

16 2. UPDA TE FIRMW ARE (1) Connect the update terminal of A V receiver with the “Writing Kit”. (2) Set the switch of “Writing Kit" (Refer to the table below). DSPBOOT CE EPM CNVSS HHHH (3) Press the "ON/ST ANDBY" button to turn the power on of A V receiver . (4) Set the switch of “Writing Kit" (Refer to the table below)[...]

17 DSP SF1 (8) Choose Ram File(OnBoard_M330.s32). Choose Ram File(OnBoard_M330.s32).[...]

18 (9) Choose Flash File(DSP : SF1). Choose "AVR1311_SF1_*_*_*_01.s32". Choose "Hex File (*.S32)".[...]

19 (10) Click the “Start” button. The Setup Status bar appears.[...]

20 (1 1) "Finished!!" is displayed. Click the "OK"” button. (12) Set the switch of “Writing Kit" (Refer to the table below). DSPBOOT CE EPM CNVSS HHHH (13) Press the "RESET" switch of “Writing Kit". (14) A V receiver is power on and starts update of DSP1. (15) "Write Comleted" is displayed in [...]

21 (19) Choose Flash File(DSP : SF2). Choose "AVR1311_SF2_*_*_*_01.s32". Choose "Hex File (*.S32)".[...]

22 (20) Click the “Start” button. (21) "Finished!!" is displayed. Click the "OK"” button. The Setup Status bar appears.[...]

23 (22) Set the switch of “Writing Kit" (Refer to the table below). DSPBOOT CE EPM CNVSS HHHH (23) Press the "RESET" switch of “Writing Kit". (24) A V receiver is power on and starts update of DSP2. (25) "Write Comleted" is displayed in the FL tube. (26) Set the switch of “Writing Kit" (Refer to the table be[...]

24 (29) Choose Flash File(MAIN). Choose "AVR1311.s32". Choose "Hex File (*.S32)".[...]

25 (30) Click the “Start” button. (31) "Finished!!" is displayed. Click the "OK"” button. The Setup Status bar appears.[...]

26 (32) Set the switch of “Writing Kit" (Refer to the table below). DSPBOOT CE EPM CNVSS HHHH (33) Press the "RESET" switch of “Writing Kit". (34) Initializing. 1. T urn off the power using ON/ST ANDBY button. 2. Press ON/ST ANDBY button while simultaneously pressing SURROUND MODE 0 and SURROUND MODE 1 buttons. 3. Check that[...]

27 ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC V oltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C. (2) Presetting • POWER (Power source switch) OFF • SPEAKER (Speaker terminal) No load (Do not connect speaker , [...]

28 SURROUND MODES AND P ARAMETERS Symbols in the table S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.”. Surround mode Channel output Surround Parameter Front L/R Center Surround L/R Surround Back L/R Su[...]

29 Surround mode Surround Parameter Tone RESTORER z 7 AFDM z 6 S.Back Subwoofer PRO LOGIC g / g x Music mode only NEO:6 Music mode only Panorama Dimension Center Width Center Image DIRECT (2 channel) S z 2 DIRECT (Multi-channel) STEREO SS MULTI CH IN SS S DOLBY PRO LOGIC g x S SSS SS DOLBY PRO LOGIC g S SSS SS DTS NEO:6 S SSS DOLBY DIGITAL SS S DOL[...]

30 Symbols in the table F This indicates the default surround mode. D This indicates the surround mode that is fixed when “AFDM” is set to “ON”. S This indicates the selectable surround mode. Surround mode NOTE Input signal types and formats ANALOG PCM DTS-HD DTS DOLBY DOLBY DIGITAL LINEAR PCM (multi ch) LINEAR PCM (2ch) DTS-HD Master Audi[...]

31 Surround mode NOTE Input signal types and formats ANALOG PCM DTS-HD DTS DOLBY DOLBY DIGITAL LINEAR PCM (multi ch) LINEAR PCM (2ch) DTS-HD Master Audio DTS-HD High Resolution Audio DTS EXPRESS DTS ES DSCRT (With Flag) DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY TrueHD DOLBY DIGITAL Plus DOLBY DIGITAL EX (With Flag) DOLBY DIGITAL EX (With [...]

32 YES YES YES YES NO NO NO Is the ON/ST ANDBY indicator on the front panel fl ashing red? Does the power turn on when the POWER switch is turned off then back on? Check the primary ciruitry parts including the POWER switch(for poor contacts, etc.), and replace any defective parts. Check the microprocessor periphery circuitry and replace any degec[...]

33 A VR-131 1 model only 2. Analog video OK OK OK OK MONITOR OUT(CVBS) Output NG MONITOR OUT(COMPONENT) Output NG Check ±5V +5V : C755 -5V : C754 Check ±5V +5V : C797 -5V : C799 Check output Output V : IC71-1pin Check output Output Y : C785 Output Pb : C787 Output Pr : C789 Check cable between main unit and monitor or Check monitor . Check cable [...]

34 YES YES YES YES NO NO NO NO NO YES YES YES No picture or sound is output. Check BD/DVD player . Check HDMI/DVI cable connection. (1) Is the HDMI/DVI cable properly connected? (3) Are you using a certi fi ed HDMI cable (one with the HDMI stamp)? (3) Are you using an HDMI/DVI cable less than 5 meters in length? (4) Are the picture and sound outpu[...]

35 YES YES YES Check TV (10) Is the TV HDCP-compatible? (14) Is the set's input set to HDMI? (12) Is the TV's input set to HDMI? (13) Are the picture and sound output when a different TV is used? Check set (A VR-131 1, 391) (1 1) Is the TV compatible with resolutions of 1080P? Use an HDCP-compatible TV . PC TVs cannot be used. Check set&a[...]

36 YES YES YES (19) Check xtal oscillator . Is there 28.6363MHz oscillation of X101? (20) Check RESET . Is RESET waveform con fi rmed in IC1 1 (97pin), when power is turned on? (If continued to "H" or " L", proceed to "NO".) HDMI output circuitry is defective (IC1 1 and surrounding circuitry). (21) Check control signa[...]

37 3.2. HDMI test point and waveforms A B C D +5V TMDS D2+ HPD TMDS D0- TMDS D0+ TMDS D1+ TMDS D1+ TMDS D1- TMDS D1- TMDS D2- 43pin 㧦 DDC_DA T A 44pin 㧦 DDC_CLK DDC_DA T A DDC_CLK TMDS D2+ TMDS D0+ HPD TMDS D1+ +5V TMDS CK+ TMDS D1- TMDS CK- TMDS D2- TMDS D0- HDMI_SCL HDMI_SDA Detail A Detail C Detail D Detail B[...]

38 DDC_CLK/DDC_DA T A/TMDS : Check item (15),(17) IPINDE/IPINVSYNC/IPINHSYNC/IPINPCK : Check item (21) 0.9V 2.48V TMDS SIGNAL DDC_CLK DDC_DATA HDMI_SDA HDMI_SCL[...]

CLOCK FLOW & W A VE FORM IN DIGIT AL BLOCK 䇭 㩿㪏㪎㪀㪘㪧㪇㪶㪦㪬㪫 㩿㪏㪏㪀㪘㪧㪈㪶㪦㪬㪫 㩿㪏㪐㪀㪘㪧㪉㪶㪦㪬㪫 㩿㪐㪇㪀㪘㪧㪊㪶㪦㪬㪫 㩿㪐㪈㪀㪘㪧㪋㪶㪦㪬㪫 㩿㪐㪋㪀㪘㪧㪌㪶㪦㪬㪫 㩿㪐㪌㪀㪪㪚㪣㪢㪶㪦㪬㪫 㩿㪐㪍㪀㪤㪚㪣㪢㪶㪦㪬㪫 㪛㪘㪠㪈㪶㪛㪘[...]

40 BLOCK DIAGRAM[...]

41[...]

42[...]

43[...]

44 LAEVEL DIAGRAM[...]

45[...]

46 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G F E D C B A PRINTED WIRING BOARDS FRONT (COMPONENT SIDE) d PHONE (COMPONENT SIDE) d HEADPHONE (COMPONENT SIDE) d REGULA TOT (COMPONENT SIDE) d 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solde[...]

47 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 G F E D C B A FRONT (FOIL SIDE) d PHONE (FOIL SIDE) d HEADPHONE (FOIL SIDE) d REGULA TOT (FOIL SIDE) d 1 2 3 D C B A 1 2 3 4 5 C B A 1 2 3 4 5 6 7 D C B A 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-[...]

48 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). POWER (COMPONENT SIDE) d POWER (FOIL SIDE) d VOLUME (COMPONENT SIDE) d VOLUME (FOIL SIDE) d AUX (COMPONENT SIDE) d AUX (FOIL SIDE) d 3 2 1 D C B A 4 3 2 1 D C B A 1 2 3 4 D C B[...]

49 MAIN (COMPONENT SIDE) d Bar code 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 M L K J I H G F E D C B A 鉛フリー半田 半田付けには、 鉛フリー 半田 (Sn-Ag-Cu) を使用 してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).[...]

50 INPUT (COMPONENT SIDE) d 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 M L K J I H G F E D C B A 鉛フリー半田 半田付けには、 鉛フリー半田 (Sn-Ag-Cu) を使 用してください。 Lead-free Solder When soldering, use the Lead- free Solder (Sn-Ag-Cu).[...]

51 INPUT (FOIL SIDE) d 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 M L K J I H G F E D C B A 鉛フリー半田 半田付けには、 鉛フリー半田 (Sn-Ag-Cu) を使 用してください。 Lead-free Solder When soldering, use the Lead- free Solder (Sn-Ag-Cu).[...]

52 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). 13 12 11 10 9 8 7 6 5 4 3 2 1 G F E D C B A HDMI (COMPONENT SIDE)[...]

53 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). HDMI (FOIL SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 G F E D C B A[...]

54 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (1/7) d[...]

55 HDMI/TMDS SIGNAL LINE D2+ D2 SHIEL D D2- D1+ D2 SHIEL D D1- D1 SHIEL D D0+ D0- CK+ D1 SHIEL D CK- CE RE MOTE NC DDC CLK DDC DA T A GND +5V HP DET INPUT-4 D2+ D2 SHIEL D D2- D1+ D2 SHIEL D D1- D1 SHIEL D D0+ D0- CK+ D1 SHIEL D CK- CE RE MOTE NC DDC CLK DDC DA T A GND +5V HP DET INPUT-3 D2+ D2 SHIEL D D2- D1+ D2 SHIEL D D1- D1 SHIEL D D0+ D0- CK+ [...]

56 ANALOG AUDIO SIGNAL LINE 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (3/7) d[...]

57 VIDEO SIGINAL LINE COMPONENT (Y) SIGNAL LINE 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (4/7) d[...]

58 ANALOG AUDIO SIGNAL LINE DIGIT AL AUDIO SIGINAL LINE 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (5/7) d[...]

59 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (6/7) d[...]

60 ANALOG AUDIO SIGNAL LINE 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (7/7) d[...]

WIRING DIA GRAM 61[...]

EXPLODED VIEW C8 C9 C10 C1 C2 C3 C1 1 C12 C4 C5 C6 C7 C13 C14 C16 S1 1 X5 S6 X6 S12 X3 S4 S4 S4 X17 S4 S2 S2 S7 S5 X17 S7 X2 X10 S1 X17 S8 X4 S8 X3 S8 S8 A VR131 1 A VR131 1 A VR391 A VR391 X3 S9 S8 X2 S3 S3 S3 S8 X2 S3 X4 S5 X2 S3 S10 X4 X2 X2 X2 X2 X2 X2 X2 X2 S3 X4 S3 S3 C15 S7 S5 X17 S7 X2 X10 P1 P9 P2 P3 P4 P6 P10 P1 1 P4 P6 P5 P8 P7 P7 P8 P13[...]

63 P AR TS LIST OF EXPLODED VIEW z Parts for which "nsp" is indicated on this table cannot be supplied. z P .W .B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P .W .B. ASS'Y , check the board parts table and order replacement parts. z Part indicated with the mark " ★ &[...]

64 Ref.No. Part No. Part Name Remarks Q'ty New P13 nsp PCB HOLDER CHE170 2 M1 nsp TOP BRACKET CMD1A355 2 M2 nsp BOTTOM CHASSIS CUA4A302 1 M3 nsp PCB BRACKET CMD1A417 2 M4 nsp PCB BRACKET CMD1A774 2 M5 nsp REAR P ANEL 131 1SPE2,131 1BKE2 CKF4A437Z 1 * M5 nsp REAR P ANEL 131 1SPE1C CKF3A437Y 1 * M5 nsp REAR P ANEL 391BKE3 CKF1A437Z 1 * M5 nsp RE[...]

65 Ref.No. Part No. Part Name Remarks Q'ty New S9 nsp SCREW CTW3+12JR 2 S10 nsp SPECIAL SCREW CHD1A023R 4 S1 1 nsp SCREW BK CTB3+8JFZR 5 S1 1 nsp SCREW SP CTB3+8JFN 5 S12 nsp SCREW BK CTBD3+8JFZR 3 S12 nsp SCREW SP CTBD3+8JFN 3[...]

66 P ACKING VIEW (for A VR-131 1, 391) P ARTS LIST OF P ACKING & ACCESSORIES (for A VR-131 1, 391) z Parts for which "nsp" is indicated on this table cannot be supplied. z Part indicated with the mark " ★ " is not illustrated in the exploded view . z The parts listed below are for maintenance only , might differ from the p[...]

67 Ref.No. Part No. Part Name Remarks Q'ty New 8 00D94301 13403 FM 1 POLE ANT . 131 1SPE2,131 1BKE2, 131 1SPE1C,391BKEA CSA1A018Z 1 8 90M-ZA000230R FM 1 POLANT(UL) 391BKE3 CSA1A019Z 1 9 9431 16009500S AM LOOP ANT CSA1A032Z 1 10 nsp POL Y BAG CPB1061W 1 1 1 943531009950D OUTCAR TON BOX 131 1SPE2,131 1BKE2 CPG1A924X 1 * 1 1 943531009960D OUTCAR [...]

68 P ACKING VIEW (for DHT -131 1XP , 391XP) P ARTS LIST OF P ACKING & ACCESSORIES (for DHT -131 1XP , 391XP) z Parts for which "nsp" is indicated on this table cannot be supplied. z Part indicated with the mark " ★ " is not illustrated in the exploded view . z The parts listed below are for maintenance only , might differ [...]

69 Ref.No. Part No. Part Name Remarks Q'ty New 4 943533009940D SNOW P AD(R) CPS1A883 1 * 5-1 541 1 10486002D INSTRUCTION MANUAL A 131 1SPE2,131 1BKE2 CQX1A1538Z 1 * 5-2 541 1 10603005D INSTRUCTION MANUAL B 131 1SPE2,131 1BKE2 CQX1A1538Y 1 * 5-1 541 1 10484006D INSTRUCTION MANUAL 391BKE3,391BKE3B CQX1A1537Z 1 * 5-1 541 1 10489001D INSTRUCTION M[...]

70 SEMICONDUCT ORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R2A15218FP (INPUT :IC61) PRELIMINARY AGND SWC AGND SLC AGND SBLC INLB/RECL2 INRB/RECR2 INR11/RECR5 INL10/RECL4 RECR3 INL11/RECL5 FLIN1 [...]

71 R2A15218FP T erminal Functions PRELIMINARY PIN No. Name Function 49 DATA Input pin of control data 50 CLOCK Input pin of control clock Output pin of FL/FR /C/SW/SL/SR /SBL/SBR channel FRIN2, FLIN2, SRN2,SLIN2, SWIN2,CIN2, SBRIN2,SBLIN2 43,42, 41,40, 39,38, 37,36 Input pin of L/R/C/SW/ SL/SR/SBL/S BR channel (Multi IN 1/2) Output pin for L/R chan[...]

72 NJM2595M (INPUT : IC71) NJM2586M (INPUT : IC73) 13 9 7 5 3 20k 20k 20k 20k 16 10 14 2 1 15 11 8 12 6 4 6dB Amp 75 Ω Dri v er S3 S2 S4 S1 20k 20k 20k S5 S6 S7 Vin1 Vin2 Vin3 Vin4 Vin5 SW 3 SW 4 SW 5 SW 1 SW 2 V + GND V - Vout3 Vout2 Vout1 6dB Amp 6dB Amp 75 Ω Dri v er 75 Ω Dri v er 9 10 8 5 6 7 4 3 2 1 11 12 13 16 15 14 17 18 19 20 21 22 23 24[...]

73 CS42528 (INPUT : IC84) CS42528 Block diagram[...]

74 CS42528 T erminal Functions[...]

75 CS497024CVZ (INPUT : IC81)[...]

76 CS497024CVZ Block diagram M12L16161A5TG (INPUT : IC83)[...]

77 TC74VHC157FT (INPUT : IC85) T5CN5 (INPUT : IC91) 4A V CC 16 4B 15 14 13 12 11 10 1 2 3 4 5 6 7 1Y 2A 2B 2Y GND 4Y 8 3Y 9 3A 3B 1A 1B SELECT ST A S G B A Y B A Y B A Y B Y[...]

78 T5CN5 T erminal Functions[...]

79 ADV7622BSTZ (HDMI : IC1 1) DDCC_SDA 5V_DETC HP_CTRLC RXB_2+ RXB_2- TVDD RXB_1+ RXB_1- CGND RXB_0+ RXB_0- TVDD RXB_C+ RXB_C- CGND CVDD DDCB_S CL DDCB_S DA DVDD DGND 5V_DETB HP_CTRLB RXA_2+ RXA_2- TVDD RXA_1+ RXA_1- CGND RXA_0+ RXA_0- TVDD RXA_C+ RXA_C- CGND CVDD DDCA_S CL 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126[...]

80 ADV7622BSTZ T erminal Functions Location Mnemonic Type Description 1 DDCC_SCL Digital Input HDCP slave serial clock port C. DDCC_SCL is a 3.3 V input that is 5 V tolerant. 2 CVDD Power Receiver comparator supply voltage (1.8V) 3 CGND Ground TVDD and CVDD Ground 4 RXC_C- HDMI Input Digital input clock Com plement of port C in the HDMI interface. [...]

81 Location Mnemonic Type Description D in the HDMI interface. 27 RXD_0+ HDMI Input Digital input channel 0 True of port D in the HDMI interface. 28 CGND Ground TVDD and CVDD Ground 29 RXD_1- HDMI Input Digital input channel 1 complement of port D in the HDMI interface. 30 RXD_1+ HDMI Input Digital input channel 1 true of port D in the HDMI interfa[...]

82 Location Mnemonic Type Description 49 TXGND Ground TXAVDD Ground 50 TX0- HDMI Output Differential Output Channel 0 Complement. Differential output of the red data at 10× the pixel clock rate; supports TMDS logic level. 51 TX0+ HDMI Output Differential Output Channel 0 True. Differential output of the red data at 10× the pixel clock rate; suppo[...]

83 Location Mnemonic Type Description N = 1, 2, 3, or 4. Set to 128 × sampling frequency (fs), 256 × fs, 384 × fs, or 512 × fs. Supports 1.8 V to 3.3 V CMOS logic levels. 69 SCLK_IN Digital Input I2S Audio Clock. Supports CMOS logic levels from 1.8 V to 3.3 V. 70 AP5_IN Digital Input Audio Input Port 5. CMOS logic levels from 1.8 V to 3.3 V. 71[...]

84 Location Mnemonic Type Description 87 AP0_OUT Digital Output Audio output port 0. 88 AP1_OUT Digital Output Audio output port 1. 89 AP2_OUT Digital Output Audio output port 2. 90 AP3_OUT Digital Output Audio output port 3. 91 AP4_OUT Digital Output Audio output port 4. 92 DGND Ground Ground for DVDD 93 DVDD Power Digital supply voltage (1.8 V) 9[...]

85 Location Mnemonic Type Description 112 RXA_C- HDMI Input Digital input clock Complement of port A in the HDMI interface. 113 RXA_C+ HDMI Input Digital input clock True of port A in the HDMI interface. 114 TVDD Power Receiver terminator supply voltage (3.3 V) 115 RXA_0- HDMI Input Digital input channel 0 complement of port A in the HDMI interface[...]

86 EX3A V (HDMI : IC16) EX3A V T erminal Functions Location Mnemonic Type Description 138 RXB_1+ HDMI Input Digital input channel 1 true of port B in the HDMI interface. 139 TVDD Power Receiver terminator supply voltage (3.3 V) 140 RXB_2- HDMI Input Digital input channel 2 complement of port B in the HDMI interface. 141 RXB_2+ HDMI Input Digital in[...]

87 2. FL DISPLA Y FLD (18-ST -13GINK) (FRONT : U100) PIN CONNECTION GRID ASSIGNMENT 59 1[...]

88 ANODE CONNECTION[...]

89 P ARTS LIST OF P .W .B. UNIT z Parts for which "nsp" is indicated on this table cannot be supplied. z Part indicated with the mark " ★ " is not illustrated in the exploded view . z The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Note: The symbols i[...]

90 Ref. No. Part No. Part Name Remarks Q'ty New C21 1 nsp CHIP CAP 0.1UF 50V K CCUS1H104KC C213 nsp MYLAR CAP 0.1UF 50V J HCQI1H104JZT C214,215 943134010520S ELECT CAP 10UF 50V CCEA1HH100T C216 943134010530S ELECT CAP 1UF 50V CCEA1HH1R0T C217 943134010670S ELECT CAP 47UF 16V CCEA1CKS470T C218,219 943134010520S ELECT CAP 10UF 50V CCEA1HH100T C2[...]

91 Ref. No. Part No. Part Name Remarks Q'ty New CN207 nsp LOCKINGTYPE STRAIGHTW AFER 2mm CJP05GI236ZW CN208 nsp W AFER STRAIGHT CJP05GA19ZY CN209 nsp W AFER ANGLE(2.5mm) CJP05GB03ZY z F201 943652000620S FUSE(0.1A 372SERIES/TR5) CBA2D0100A3EYT FL201 9431720101 10S VFD HCA-18SM01T CFLHCA18SM01T * GND21,22 nsp PCB BRACKET CMD1A569 JK201 90M-YT004[...]

92 MAIN P .W .B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC41 00D2630641002 REGULA TOR IC NJM7912F A HVINJM7912F A IC42 00D2630801004 REGULA TOR IC NJM7812F A HVINJM7812F A IC45 00D2631 162014 REGULA TOR IC KIA78R05PI HVIKIA78R05PI IC46 231010031706S REGULA TOR IC KIA278R05PI HVIKIA278R05PI Q401 00MHT8[...]

93 Ref. No. Part No. Part Name Remarks Q'ty New ZD41 943202010070S DIODE ZJ12B CVDZJ12BT ZD48 943202010080S DIODE ZJ5.1B CVDZJ5.1BT ZD49 90M-HD302440R DIODE ZJ4.7B CVDZJ4.7BT ZD51-60 90M-HD302390R DIODE ZJ3.3B CVDZJ3.3BT RESISTORS GROUP R494-501 nsp MET AL OXIDE FILM RES(4.7KOHM 5% 1W) KRG1SANJ4R7RT R502 nsp MET AL OXID EFILM RES(120OHM 1W J) [...]

94 Ref. No. Part No. Part Name Remarks Q'ty New C423-426 nsp CERAMIC CAP 33PF 50V J CCCT1H330JC C427 943134010660S ELECT CAP 470UF 6.3V CCEA0JH471T C428 943134010490S ELECT CAP 100UF 10V CCEA1AH101T C429-431 nsp MYLAR CAP 0.01UF 100V J 131 1E2 HCQI1H103JZT C429-431 nsp MYLAR CAP 1000PF 100V J MYLAR 131 1E1C,391E3, 391E3B,391EA HCQI1H102JZT C43[...]

95 Ref. No. Part No. Part Name Remarks Q'ty New C504 943134010600S ELECT CAP 3300UF 16V CCEA1CH332E C505 943134010680S ELECT CAP 47UF 50V CCEA1HH470T C508 943134010520S ELECT CAP 10UF 50V CCEA1HH100T C559 943134010470S ELECT CAP 0.1UF 50V CCEA1HH0R1T C561 943134010530S ELECT CAP 1UF 50V CCEA1HH1R0T C563,564 943134010470S ELECT CAP 0.1UF 50V CC[...]

96 INPUT P .W .B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC60 943231010390S REGULA TOR IC KIA7805BPI CVIKIA7805BPI * IC61 943235003810S IC R2A15218FP CVIR2A15218FP IC62-65 00D2631289900 IC AZ4580MTR-E1 CVIAZ4580MTR-E1 IC66,67 00D2630934900 IC BA4510F HVIBA4510F IC68 943231010390S REGULA TOR IC KIA7805[...]

97 Ref. No. Part No. Part Name Remarks Q'ty New RN61 nsp CHIP RES(100OHM 5% 1608X4) CRJ104DJ101T RN80 nsp CHIP RES(33OHM 5%,1608X4) CRJ104DJ330T RN81,82 nsp CHIP RES(10KOHM 5% 1608X4) CRJ104DJ103T RN83-90 nsp CHIP RES(33OHM 5% 1608X4) CRJ104DJ330T RN91,92 nsp CHIP RES(100OHM 5% 1608X4) CRJ104DJ101T RN93 nsp CHIP RES(10KOHM 5% 1608X4) CRJ104DJ1[...]

98 Ref. No. Part No. Part Name Remarks Q'ty New C696,697 943134010610S ELECT CAP 4.7UF 50V CCEA1HH4R7T C698 nsp CHIP CAP 0.1UF 50V CCUS1H104KC C701-704 nsp CHIP CAP 1500PF 50VK CCUS1H152KC C705,706 nsp CHIP CAP 330PF 50V J CCUS1H331JA C707,708 nsp CHIP CAP 1500PF 50VK CCUS1H152KC C709 nsp CHIP CAP 0.1UF 50V CCUS1H104KC C710,71 1 nsp CHIP CAP 3[...]

99 Ref. No. Part No. Part Name Remarks Q'ty New C808 943134010610S ELECT CAP 4.7UF 50V CCEA1HH4R7T C809 nsp CHIP CAP 0.1UF 50V CCUS1H104KC C810 943134010490S ELECT CAP 100UF 10V CCEA1AH101T C81 1 943134010630S ELECT CAP 470UF 10V CCEA1AH471T C812 nsp CHIP CAP 0.1UF 50V CCUS1H104KC C813 nsp CHIP CAP 1000PF 50V CCUS1H102KC C814 nsp CHIP CAP 0.1U[...]

100 Ref. No. Part No. Part Name Remarks Q'ty New C940,941 nsp CHIP CAP 1000PF 50V CCUS1H102KC C946-953 nsp CHIP CAP 1000PF 50V CCUS1H102KC C954 nsp CHIP CAP 0.015UF 50V CCUS1H153KC C955 nsp CHIP CAP 1UF 10V CCUS1A105KC C956 nsp CHIP CAP 0.1UF 50V CCUS1H104KC C957 943134010530S ELECT CAP 1UF 50V CCEA1HH1R0T C958-961 nsp CHIP CAP 0.1UF 50V CCUS1[...]

101 Ref. No. Part No. Part Name Remarks Q'ty New TU61 943183010310S TUNER(EUR)FM,AM,RDS(S/LAB) 131 1E2,131 1E1C,391EA CNVMW104MV1S63SN * TU61 943183010320S TUNER(USA)FM(SCREW:FTYPE),AM(S/LAB) 391E3,391E3B CNVMW004MV1S63SA * X801 943141010360S CRYST AL 24.576MHz 15PF 30PPM HOX24576E150TF X901 943141010370S CRYST AL 10.000MHz 22PF 30PPM HOX10000[...]

102 HDM P .W .B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC1 1 943236010380S IC ADV7622BSTZ CVIADV7622BSTZ * IC15 943239010400S REGULA TOR IC NJM2845DL133 CVINJM2845DL133 IC16 nsp IC EX3A V CVIEX3A V Q101 00D2690184907 CHIP TR KRA102S HVTKRA102S Q102 90M-BA001620R CHIP TR KRC103S CVTKRC103S Q103 00D269[...]

103 Ref. No. Part No. Part Name Remarks Q'ty New C178 nsp CHIP CAP 0.015UF 25V CCUI1E153KC C179 nsp CHIP CAP 15PF 50V CCUI1H150JA OTHERS P ARTS GROUP BK1 1,12 nsp PCB BRACKET CMD1A569 CN12 nsp W AFER SMD(2MMPITCH) CJP05GA208ZY CN8B nsp W AFER CJP19GA1 15ZY JK1 1-15 644010108608S HDMI JACK(SMD) CJJ9H010Z L101-108 nsp CHIP FERRITE BEAD(60ohm 160[...]

104 TECHNICAL SPECIFICA TIONS DIMENSION n Front speaker (SC-F391) Type: 2-way, 3-speakers Closed box / Low-leakage-fl ux Drive units: 8 cm cone bass-mid x 2 2.5 cm high range x 1 Input impedance: 6 Ω Max. input: 60 W (IEC) 120 W (PEAK) Frequency range: 150 Hz – 22 kHz Dimensions: 125 (W) x 320 (H) x 155 (D) mm (4-59/64” x 12-19/32” x 6-7/64[...]

105 SC-F391 EXPLODED VIEW SC-F391 P ARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No. Part Name Remarks Q'ty New 1 984189000120D SPEAKER A[...]

106 SC-R391 EXPLODED VIEW SC-R391 P ARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No. Part Name Remarks Q'ty New 1 984189000140D SPEAKER A[...]

107 SC-C391 EXPLODED VIEW SC-C391 P ARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No. Part Name Remarks Q'ty New 1 984189000130D SPEAKER A[...]

108 DSW -391 EXPLODED VIEW DSW -391 P ARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the followin[...]

109 SYS-391HT P ACKING VIEW 9 7 3 5 4 1 2 2 3 8 6 7 10 11 12[...]

11 0 SYS-391HT P ARTS LIST OF P ACKING VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only , might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : [...]

111 8 7 6 5 4 3 2 1 A B C D E F SCHEMA TIC DIAGRAMS (1/1)[...]