DKS Enterprises 9310 manuale d’uso

Model 9310 Vehicular Slide Gate Operator DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com Owner’s Manual P/N 9310-065 Rev D 5/05 Copyright 2003 DoorKing, Inc. All rights reserved.[...]

2[...]

3 Use this manual with the following models only . All 9310 models with circui t board 4403-010. IMPORTANT! The 4403 circuit board used in the model 9310 IS NOT interchangeable with the 440 2 circuit board used in the earlier model 9300 operators. NOTE: Models 9310-081, 9310-083, 9310-085, 931 0-087, 9310-089, 9310-09 1, 9310-093, 9310- 095 and 931[...]

Mount operator to pad using 3/8 or 1/2 sleeve anchors . See page 14-15. 1 2 Attach chain. Adjust chain t o allow approximately 1-inch of sag per 10-feet of gate width. Be sure to remove the pin from the breather plug. See page 16-17. 3 Connect supply voltage as des cribed in sect ion 2.2. Be sure power is OFF! See page 22. 4 Connect control wiring [...]

9406 9406 EXIT LOOP REVERSE LOOP ON 12 3 1 DIRECTION 2 TIMER 1 Open Cycle Phot ocell 2 Close Cy cle Photoc ell 3 Open Cycle Conta ct Sensor 4 Close Cy cle Contac t Sensor 5 Common 6 Common Secondary Entrapment Protecti on Devices CAUTIO N 16-2 0 HIGH VOLT AGE! TIMER REV SENS OPEN REV SENS CLOSE TIME DELAY 1 2 3 4 5 6 7 8 1 2 3 4 ON REVERSE LOOP GAT[...]

TABLE OF CONTENTS Important Notices .............................................................................................................. ........................................8 Important Safety Instructions ...................................................................................................................................[...]

Section 4 – Operating Instructions 4.1 Power and Reset Switches ......................................................................................................................39 4.2 Shutdown Conditions ........................................................................................................ .......................40 Soft Shu[...]

IMPORTANT NOTICES Vehicular gate sy stems provide convenien ce to thei r users and limit vehicular t raffic onto your property. These systems can p roduce high levels of f o rce; therefore it is important that you are aware of possible hazards associated with your gate o perating system. These hazards may inclu de pinch points, entrapment, absence [...]

IMPORTANT SAFETY INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or pl ay with gate controls. Keep the remote control away from children. 3. Always keep people an d objects away from g ate. NO ONE SHOUL D CROSS THE PATH OF THE MOVING GATE. 4. Test the operator monthly.[...]

RESTRICTIONS AND WARNINGS Install The Gate Operator Only If: • The operator is appropriate for the usage Cla ss of the appli cation and the gate is within the weight and length limitations specified for the operat or. • All openings of a horizonta l slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet (1.2 m) ab[...]

ENTRAPMENT PREVENTION This vehicular gate operator is equippe d with an in herent (Type A) entrapment sensing system. This system will sense an obstructi on in both the opening and closing gate cycle s, and will cause the gate to reverse direction should an obst ruction be encoun tered. If the system detects a secon d obstruction before reaching th[...]

GLOSSARY GATE – A moving barrier su ch as a swinging, slidin g, raising, lowering, or th e like, barrier, that is a stand-alone passag e barrier or is that p ortion of a wa ll or fe nce system that cont rols entrance and/or egress by persons or vehicl es an d completes the peri meter of a defined area. RESIDENTIAL VEHICULAR GATE OPERATOR-CLASS I [...]

SECTION 1 - INST ALLA TION Prior to beginning the installation of the slide gate operator, we suggest that you become familiar wit h the instructions, illustration s, and wiring guide-lines in this manu al. This will help insure that your installation is performed in an efficient and professio nal manner. The proper installation of the vehicular sl[...]

1.2 Concrete Pad The model 9310 vehicular gate operato r is desi gned to be mounted on a concrete pad. 1. Construct a form for the mounting pad ac cording to the specifications shown bel ow. Note that the pad for the 1 H P operator extends an a dditional 6 inches to the right to accommodate the larger cov er . Be sure to level the top edge of the f[...]

1.3 Operator Installation • Position the operator o n the pad so that there is a minimum clea rance of one (1) inch between the back of the operator housing and the gate. 90° • IMPORTANT!! Be su re that the operator is parallel to the gate! Installing the operator in any other manner will cause excessive chain noise, chain wear and stretching,[...]

1.4 Chain Installation 1. Secure the chain bra ckets to each end of the gate so that the brackets are level with the top chain cutouts in the operator housing . Brackets should be attached to the insi de of the frame so that the chain bolts, when attached, do not protrude beyond the frame of the gate. 2. Remove the breather plug pin from the gear-b[...]

1.5 Front Mount Installation 4 8 GROUND LEVEL CONCRETE PAD REMOVE BREATHER PLUG PIN 17[...]

1.6 Rear Mount 4 8 GROUND LEVEL CONCRETE PAD REMOVE BREATHER PLUG PIN Gate Brackets Idler Assembly P/N 2600-818 18[...]

1.7 Warning Sign Installation This DoorKing slide gate operator is shipped with two warning signs. The purpose of the warning signs is to alert uninf ormed persons, a nd to remind persons familiar with the system, that a potential hazard may exist so that appropriate action can be ta ken to avoid the hazard or to redu ce exposure to the hazard. WAR[...]

20[...]

SECTION 2 – WIRING Before attempting to connect any wiring to the oper ator, be sure that the circuit brea ker in the electrical panel is in the OFF po sition. A separate po wer disconnect must be installed at the operator location. Perm anent wiring must be installed to the operato r as required by local electrical codes. It is recommended that [...]

2.2 High Voltage Connections Use Table 1 to determine high voltage wire size re quirements. T he distance shown in the ch art is measured in feet from the operator to the power so urce. If power wiring is grea ter than the maximum distance shown, it is reco mmended that a service feeder be in stalled. A separate powe r disconnect must be installed [...]

2.3 Control Wiring Controls must be far en ough from the gate so that th e user is prevented from co ming in contact with the gate while operating the c ontrols. Outdoor or easily acc essible controls should have a security feature to prev ent unauthor i zed use. • Connect optional control devices to the operato r terminal strip a s shown below. [...]

2.4 Secondary Entrapment Non-Contact Sensors • Before connecting non-contact or contact sensors, refer to pag e 32 for operation al description of these sensors. • Disconnect power to the gate operator bef ore installing the non-contact se nsors. • See diagram below for suggeste d placement of sensors. (Diagr am is for illustration purposes o[...]

2.5 Contact Sensors • Before connecting non-contact or contact sensors, refer to pag e 32 for operation al description of these sensors. • Disconnect power to the gate operator before in stalling the contact sensors. • Connect the contact se nsors as shown below to the auxiliary terminal strip located on the 4403 control board. • Contact se[...]

2.6 Loop Detectors Loops and loop detectors must be in stalled with this gate opera tor to prevent the gate from accidentally closing on vehicles th at may be in the path of the gate . • Loop detector wiring is sh own for DoorKing model 9406 Plug-I n loop detector only. If other loop detectors are used, refer to the in stallation instructions sup[...]

2.7 Gate Tracker This gate operator is equi pped with outputs from the circuit boa rd that will repo rt operator status to a companion DoorKing Acce ss Control System (Model 1833, 1835, 1837 or 18 38) when equipped wit h an optional Tracker expansion board. This report in clud es items such as gate operator cy cle count, any shorted inputs, loop d [...]

2.8 Alarm Reset Switch The gate operator is equipped with a built-in re set switch that will silence the entrapment alarm an d return the operator to normal operation after a hard shutdown occurs. An auxiliary reset button may be added provided that the following con dition is met. • The alarm-reset button must be loca ted in the line of sight of[...]

2.10 Master / Slave Wiring The interface wiring between the two operators require s four (4) 18 AWG wires for co ntrol. Each operator must be connect ed to it's own power so urce as described in section 2 .2. Be sure that both operators are wired to the same phase in the b reaker panel. Check at the breaker panel by measuring voltage from HOT [...]

2.11 Secondary Entrapment Protecti on for Master / Slave Configuration Secondary entrapment p rotection for slide g ate oper ators connected in a m aster / slave configuratio n will require three sets of photo-beams to insure protection. • One photo-beam is directed across th e roadway and connected to the CLOSE photo-b eam input on the auxiliary[...]

2.12 Main Terminal (P1) Description 1. 24 VOLT COMMON Same as terminal 13. 2. OPEN / RADIO RELAY Functions same as terminal 4. 3. 24 VOLT RADIO POWER 4. FULL OPEN / CLOSE INPUT When gate is closed, input w ill open gate to full position. When gate is open and auto clo se timer is turned on, input will re-set and hold timer. When gate is open and au[...]

2.13 Second ary Device Terminal (P3) External entrapment prevention devices are connected here. 1. OPEN PHOTO-BEAM This input is only active when the gate is in the opening cycle. An open photo-beam input during the opening cycle will cause the gate to stop. T he gate will remain stopped until the photo-beam input is cleared, at which time the gate[...]

SECTION 3 - ADJUSTMENTS The switch settings and adjustments in this chapte r should be made after your installation and wiri ng to the operator(s) is comp lete. Whenever any of the programming switche s on the circuit board are changed, power must be shut-off, and then turned back on for the new setting to take effect. 3.1 Circuit Board Adjustments[...]

3.2 Switch Settings The two DIP-switches located on th e circuit board are used to p rogram the operator to operate i n various modes and to turn on or off various op erating features. When ever a switch setting is changed, power to the o perator must be turn ed OFF and then turned back o n for the new setting to take affect. Check and review ALL s[...]

3.3 Programming Switch Description and Function 8-DIP (Top) S witch Sw it ch 1 : Set so that the operator cycles open upon initial p ower up and open command. If the operator cycles close, turn powe r o ff and change the setting on this switch. Sw it ch 2 : Turns the auto c lose timer on or off. Set from 1 to 23 seconds. Loops and loop detectors, p[...]

3.4 Limit Switch Adjustments 1. Be sure that power to the operator is OFF. 2. Push the gat e to the open po sition. Adjust the OPEN limit nut so that it is activating the OPEN limit switch. 3. Push the gat e to the close position. Adjust the CLOSE limit nut so that it is activ ating the CLOSE limit switch. 4. After adjusting the limit-nut s, be sur[...]

3.5 Reverse Sensitivity Adjustment This vehicular gate operator is equippe d with an in herent (Type A) entrapment sensing system. This system will sense an obstru ction in either the opening or clos ing gate cycles and will cause the gate to reverse direction should an ob struction be encountered. Fo r this system to function correc tly, the gate [...]

38[...]

SECTION 4 – OPERA TING INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate co ntrols. Keep the remote control away from children. 3. Always keep people an d objects away from gate. NO ONE S HOULD CROSS THE PATH OF THE MOVING GATE 4. Test the operator mo[...]

4.2 Shutdown Conditions Under various entrapme nt conditions the operator will assume either a soft or hard shutdown (alarm ) condition. To determine what type of reset acti on is required, y ou will nee d to understand how the different entrapment conditions affect the gate ope rat or. Soft Shutdown This occurs in various situations where the in h[...]

Hard Shutdown A hard shutdown condition occu rs when the inhe rent entrapme nt protection system has sensed two consecutive obstruction s before the gate re aches the full open o r full closed position. It can also be an indication that the g ate is too heavy or that the gate hardware ( wheels, rollers) is in poor condition and needs to be correcte[...]

4.3 Manual Gate Operation This operator is equi pped with a manual releas e system that will allow th e gate to be pushed open in the event of a power outage or equipment failure. There are two manual release system s that are available on this gat e operator. The standard type release is the FAIL-SAFE system (req uired by many city cod es), while [...]

Fail-Secure Manual Operation The FAIL-SECURE option locks the gate whe n prim ary (AC) power is removed and requires a keyed release to place the gate in manual operation. Th e FAIL-SECURE option is typically used i n CLASS III and CLASS IV applications. • Be sure that primary (AC) and backup (DC) powe r is removed o r shut-off prior to placing t[...]

44[...]

SECTION 5 – MAINTENANCE AND TROUBLESHOOTING Inspection and service of this gate op erator by a qualified technici an should be performed a nytime a malfunction is observed or suspected. High cycl e usa ge may req uire more frequent service checks. 5.1 Maintenance When servicing the gate operator, alwa ys check any secondary (external ) reversing [...]

5.2 Operator Diagnostics This gate operator is de signed with built-in diag nost ics that will ale rt you to potential or existing problems that the micro processor has detected. Specifi c fault conditions are checked and the operator will signal that a fault exist through the built -in alarm. Constant tone is heard when po w er is applied: • Thi[...]

5.3 Trouble Shooting Have a good VOM meter to che ck voltages and continuity. A Meg-Ohm m eter capable of checking up to 500 meg-ohms of re sistance is necessary to properly check the integrity of the gro und loops. When a malfunction occurs, isolate the problem to one of three areas: 1) the operator, 2) the loop system, 3) the key ing device s. Us[...]

Gate opens a short distance, then stops and reverses. • Disconnect the gate from the gate operator and check that the gate slides freely without any binding. • Re-adjust the open reverse sensitivity . • Replace the circuit board. Gate opens but will not close. • Check the input LEDs. Any ON will hold the gate open and indicates a problem wi[...]

Title: Date: Rev. Dwg . No. DOORKING, IN C., INGLEWOOD, CA 903 01 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4403-010 Circuit Board Solenoi d Alarm Reset Alarm White Red Yellow Black P3 Current Senso r Do nut Motor Volt- Ph Turns ½ HP All 2 1 HP Sgl[...]

Title: Date: Rev. Dwg . No. DOORKING, IN C., INGLEWOOD, CA 903 01 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4403-010 Circuit Board Solenoi d Alarm Reset Alarm White Red Yellow Black P3 Current Senso r Do nut Motor Volt- Ph Turns ½ HP All 2 1 HP Sgl[...]

Title: Date: Rev. Dwg . No. DOORKING, IN C., INGLEWOOD, CA 903 01 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4403-010 Circuit Board Solenoi d Alarm Reset Alarm White Red Yellow Black P3 Current Senso r Do nut Motor Volt- Ph Turns ½ HP All 2 1 HP Sgl[...]

Title: Date: Rev. Dwg . No. DOORKING, IN C., INGLEWOOD, CA 903 01 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4403-010 Circuit Board Solenoi d Alarm Reset Alarm White Red Yellow Black P3 Current Senso r Do nut Motor Volt- Ph Turns ½ HP All 2 1 HP Sgl[...]

Title: Date: Rev. Dwg . No. DOORKING, IN C., INGLEWOOD, CA 903 01 1 2 3 4 5 N.O. N.C. COM N.O. N.C. COM White Red Yellow Blue Limit Limit Partial Limit P2 P1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4403-010 Circuit Board Solenoi d Alarm Reset Alarm White Red Yellow Black P3 Current Senso r Do nut Motor Volt- Ph Turns ½ HP All 2 1 HP Sgl[...]

5.4 Accessories The following accessory items can be used with the m odel 9310 slide gate operator. Contact Sensor Contact sensor s for use as a secondary ent rapment protection device. Miller Edge, Inc. ME120, ME 123, MG020, MGR20, MGS20 Photo Cell Non-contact (photo cells) sens ors for use as a secondary entrapm ent protection device. P/N 8080-01[...]

55[...]