Drolet DH04200 manuale d’uso

OWNER`S MANUAL OIL BURNING STOVE EVEREST Vérified and tested following CAN/CSA B140.3 et UL 896 standards by : Intertek Testing Services Manufactured by: 1700 Léon-Harmel Québec, (Québec) G1N 4R9 www.drolet.ca tel : (418 ) 527-3060 Fax : (418 ) 527-4311 READ THESE INSTRUCTIONS AND SAVE FOR REFERENCE 990615/45088A_feb 03[...]

TABLE OF CONTENT TECHNICA L DATA ................................................................................................................. ........................ 1 INSTALLATION INSTRUCT IONS ...................................................................................................... ............ 2 LOCATING TH E STOVE ...........[...]

INSTALLATION INSTRUCTIONS LOCATING THE STOVE • Install the stove as close to the chimney as po ssible. • Many configurations are possible, the most frequent a re illust rated in figures 1, 2 and 3. • Respect clearances indicated on page 1. T hey have been tested according to approvals. • Always respect clearances of stove pipes manuf actu r[...]

CHIMNEY INFORMATIONS • Before the hook up of the stove, check if the chimney is in good condition and that the quality of the flue pipe will allow a sufficient d raught. For a good combustion, refer to t he technical data of the stove to know the minimum draught requi red. • Factory built ‘’A’’ type chimney or ‘’L’’ type chimney[...]

CONNECTING THE STO VE TO THE CHIMNEY • The gases are vented from the back of the unit. The female part of the black pipe connector has to be installed toward the flue con necto r of the stove. Secure all conne ctions with the (3) self taping screws, with 120 o distance between each of them. • The connection between stove pipes a nd chimney has [...]

LEVELING THE UNIT • Now that the stove is in place an d properly hooked up to the chimney, you have to adjust the level on the burner. • Put the level in the middle of the burner parallel to the door. (Fig ure 9A). Screw or unscrew the adjustable legs to level the burner with a 7/16" key (10 mm). • Put the level in the middle of the burn[...]

CONNECTING STOVE TO OIL TANK • Make sure that the tank outlet is 12" (30 5 mm) hi gher than the inlet of the carburetor. (Gravity fed) • Use only copper piping to conne ct tank to stove. • Make sure that there is a small slop e on t he connection from the tank toward the stove. • A 3" (75 mm) down slope is neede d on the tank itse[...]

ADJUSTING THE DRAUGHT • Your stove operated with natural drau ght, creat ed by the ascension of combustion gase s in the chimney. This movement creates a si phon effect in the stove and forces ambient air to go in the burner by the holes in its surround. These orifi ce s let air in for com bustion. • For the unit to function p roperly, it is es[...]

OPERATION INSTRUCTIONS COMBUSTIBLE • Your stove has been designed to work with oil #1 or #2. DO NOT USE GASOLINE, CRANKCASE OIL OR ANY OIL CONTAINING GASOLINE. The manuf acturer declines all responsibility reg arding damage cause by using other combusti bles. • Make sure to use oil without impurities whi ch may plug filters and valve’s orific[...]

LIGHTING (CONT’D) • Place the flow regulating handl e on the "1" posit ion, as soon as the oil enters the burner return to "0" position. • Open the door a nd pore into the burner 2 to 3 once (75 ml) of lighting g el or wood alcohol. NOTE : USE OF LIGHTING GEL IS BETTER FOR A SAFE IGNITION. • With a long wood match, ignit[...]

TURNING THE STOVE OFF • Set the flow regulating handle to position ‘’0’’. • If you plan to keep the stove off for a long while, it is recomm ended to disarm the valve’s lever and close the tap on the pipe between the st ove and your oil tank. ALWAYS KEEP THE VALVE SHUT OFF WHE N THE BURNER IS NOT OPERATING MAINTENANCE ONCE A WEEK : ?[...]

TROUBLESHOOTING GUIDE PROBLEMS CAUSES SOLUTION ON POSITION 6 (MAXIMUM) THE FLAME IS LONG AND SMOKY, THERE IS SUIT BUILD UPON THE GLASS. Position 6 was reached too quickly. 1. Set flow regulating handle to position 1; 2. wait for combustion to stabilize; 3. Progressively increase flow to desired position. NOTE : SEE LIGHTING PROCEDURES. Maximum flow[...]

TROUBLESHOOTING GUIDE (CONT’D) PROBLEMS CAUSES SOLUTION THE FLAME PRODUCES SMOKE, IN ANY POSITION. Door gasket is not selling properly. 1. Tighten door by turning counter-clockwise the do or handle; 2. Check if gasket needs to be changed. The burner orifice s are plugged up. 1. Clean the burner with a metallic brush. Draught is too low. 1. Make i[...]

SPARE PARTS After years of use, if you need to replace some pa rts, please co nta ct your SUPPLIER or one of our Drolet approved DEALERS . • Give him product data as displ ayed in your warr anty voucher or on your applian ce’ s name plate at the rear. Keep the warranty v oucher even after its EXPIRY date. • Our dealers are in po ssessi on of [...]

SPARE PARTS (CONT’D) Figure 16: EVEREST EXPLODED VIEW, SPARE PARTS LIST Page 14 of 15[...]

W A R R A N T Y The warranty of the ma nufacturer applies to the original buy er only. This warranty may not be transferred to a second person and becomes effective on the date of purchase. Proof of purchase is necessary to validate the w arranty and to establish the w arranty coverage period. The warranty is conditional to normal residential use o[...]