Eagle 642c iGPS manuale d’uso

Pub. 988-0152-161 www.eaglegps.com IntelliMap 642c iGPS Mapping GPS Receiver Installation and Operation Instructions ®[...]

Copyright © 2005 LEI-Eagle All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle ® is a registered trademark of LEI. MapCreate  , Fre[...]

i Table of Contents Section 1: Read Me First! ............................................................... 1 Capabilities and Specifications: ......................................................... 2 How GPS Works ................................................................................. 4 Introduction to GPS and WAAS...................[...]

ii Navigate a Trail ............................................................................ 47 Navigate a Back Trail ................................................................... 49 Transfer Custom Maps and GPS Data Files ................................... 50 Cancel Navigation ............................................................[...]

iii GPS Simulator .................................................................................. 72 Initialize GPS .................................................................................... 74 Map Auto Zoom ................................................................................. 74 Map Data ...................................[...]

iv Find Interstate Highway Exits ...................................................... 103 Find Map Places or Points of Interest (POI) ................................. 105 Find Streets or Intersections ......................................................... 107 Find a Street ......................................................................[...]

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxious to begin navigating, but we have a favor to ask. Before you grab the IntelliMap ® 642c iGPS and begin installing it, please give us a moment or two to explain how our manual can help you get the b[...]

2 After you've learned the basics (or if you already have some GPS expe- rience), you may want to try out some of the IntelliMap 642c's many advanced navigation features. That brings us to Section 4, Advanced GPS Operations . This section contains the rest of the unit's GPS com- mand functions, organized in alphabetical order. When y[...]

3 Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable for saltwater use. MMC slots: ...................... One with waterproof door (SD card compatible). Recording: ........................ MMC & SD cards for recording GPS trip de- tails and displaying charts or cu[...]

4 NOTE: The above memory capacities refer only to the In telliMap 642c's on- board memory. The amount of GPS data you can record and save for recall later is limited only by the number and size of MMC cards you have. NOTICE! The storage temperature range for your IntelliMap 642c is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75[...]

5 The background map is suitable for many navigation chores, but for maximum accuracy and much more detail, you need our optional map- making software, MapCreate  6, or one of our special plug-and-play mapping cards. Some unit features — such as searching for businesses and addresses — won't work without a custom MapCreate map. There is[...]

6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliMap 642c and plug in the power. Or you might want to see how our text formatting makes the manual tuto- rials easy to skim. If that's[...]

7 The system requires signal reception from three satellites in order to determine a position. This is called a 2D fix. It takes four satellites to determine both position and elevation (your height above sea level — also called altitude). This is called a 3D fix. Remember, the unit must have a clear view of the satellites in order to receive the[...]

8 Remember that this receiver is only a tool. Always have another method of navigation available, such as a map or chart and a compass. Also remember that this unit will always show navigation information in the shortest line from your present position to a waypoint, regardless of terrain! It only calculates position, it can’t know what’s betwe[...]

9 4. The wait message disappears and the IntelliMap 642c begins show- ing navigation information along the trail. Now, begin moving and fol- low your IntelliMap 642c. Translated into complete English, step 1 above would mean: "Start on the Map Page. Press the Menu key twice. Next, repeatedly press (or press and hold) the down arrow key to scro[...]

10 Notes[...]

11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1. Determine the approximate location for the GPS unit, so you [...]

12 This may result in corrosion of the plug body along with the electri- cal contacts in the cable and the unit's power socket. In saltwater environments we recommend you connect the power cable to the auxiliary power switch included in most boat designs. If that results in electrical interference, or if such a switch is not available, we reco[...]

13 CAUTION: Failure to use the enclosed 3-amp fuse will void your warranty! For a replacement, use a type 3AG 3-amp fuse. This unit has reverse polarity protection. No damage will occur if the power wires are reversed. However, the unit will not work until the wires are attached correctly. Cable connections. 3-amp fuse Rear view of unit Power Conne[...]

14 NMEA Cable Connections NMEA is a standard communications format for marine electronic equipment. For example, an autopilot can connect to the NMEA inter- face on the IntelliMap 642c and receive positioning information. The IntelliMap 642c can exchange information with any device that trans- mits or receives NMEA 0183 data, however, a communicati[...]

15 mation is on the inside back cover of this manual. For a complete look at the many mounting options, visit the RAM web site at www.ram- mount.com. Optional R-A-M mounting system. Bracket Installation Mount the IntelliMap 642c in any con ve ni ent lo ca tio n, pr ovi de d t he re is clearance behind the unit when it's tilted for the best vie[...]

16 Some customers, however, prefer to mount the bracket to the side of the cable hole — it's a matter of personal preference. Front view (left) and side view (right) showing dimensions of the IntelliMap 642c when mounted on gimbal bracket. After drilling the hole, pass the power cable's bare-wire end down though the hole from the top. I[...]

17 pack expands the uses for your GPS unit. The PPP makes it easy to transfer your unit from a boat to a car, recreational vehicle, airplane or other vehicle without drilling and mounting a second bracket. You can use your unit in your own car or boat, then take it along when riding in a friend's vehicle that's not equipped with GPS. Most[...]

18 Additional MMC cards are available from LEI Extras; see ordering in- formation inside the back cover of this manual. MMCs and SD cards are also available at many camera and consumer electronics stores. The MMC slot is located in a compartment on the front of the case. The compartment door is located at the lower right corner. The following figur[...]

19 MapCreate™ 6 CD-ROM (left) MMC card reader for USB ports (right). Now that you have your IntelliMap 642c installed, move on to Section 3, Basic GPS Operations . There, we'll present a series of step-by-step tutorials to teach you the basics of GPS navigation.[...]

20 Notes[...]

21 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetical order. Before you turn on the unit and fin[...]

22 4. ARROW KEYS – These keys are used to navigate through menus, make menu selections and move around the map. 5. ENT/ICONS – The Enter key allows you to save data, accept values and execute menu commands. It is also used to create event marker icons. 6. EXIT – The Exit key lets you return to the previous screen, clear data or close a menu. [...]

23 Main Menu. The Main Menu commands and their functions are: Screen : changes the contrast or brightness of the display screen. Sounds : enables or disables the sounds for key strokes and alarms and sets the alarm style. Transparency : adjusts the level of transparency for menus. Alarms : turns GPS alarms on or off and changes alarm thresholds. Ro[...]

24 Pages The unit has three Page displays: Satellite Status Page, Navigation Page and Map Page. They are accessed by pressing the PAGES key, then using ← → to select a Page. (Clear the Pages Menu by pressing EXIT .) Pages Menu showing some Map display options. Satellite Status Page The Satellite Status Page, shown in the following images, provi[...]

25 Satellite Status Page. The first figure (left) indicates unit has not locked on to any satellites and does not have a fix on its position. The second figure (right) shows satellite lock-on with a 3D position acquired (lati- tude, longitude and altitude), and WAAS reception. This screen shows a graphical view of the satellites that are in view. E[...]

26 The Satellite Status Page has its own menu, which is used for setting various options. (Options and setup are discussed in Sec. 5). To access the Satellite Status Page Menu, from the Status Page, press MENU . Navigation Page This screen has a compass rose that not only shows your direction of travel, but also the direction to a recalled waypoint[...]

27 Speed (ground speed) is the velocity you are making over the ground. (If you wish, you can customize the Speed data box to display Closing Speed instead. Closing Speed is also known as velocity made good. It's the speed that you're making toward the waypoint. For instructions, see the Customize Page Displays entry in Sec. 5.) Track is [...]

28 course. You need to steer left to return to the desired course. You can use the ZIN or ZOUT keys to change the cross track error range. A circular symbol depicting your destination (waypoint) appears on the screen as you approach the waypoint, as shown on the screen in the preceding figure. Travel Time is the time that it will take to reach your[...]

29 The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its coverage area and the amount of mapping detail shown. There are 40 available map zoom ranges, from 0.02 miles to 4,000 miles. Map Page opening screen (left). Map page zoomed to 100 miles (cen- ter). Map zoomed to 10 miles (right). Over Zoomed means you have reached the detail li[...]

30 Background map vs. MapCreate map content The background map includes: low-detail maps of the whole world (con- taining cities, major lakes, major rivers, political boundaries); and me- dium-detail maps of the United States. The medium-detail U.S. maps contain: all incorporated cities; shaded metropolitan areas; county boundaries; shaded public l[...]

31 When the map is zoomed out far enough, most POIs appear as square dots (left). As you zoom in closer, the symbols become readable icons. In the 0.2-mile zoom example (right), the cursor has selected the Cupps Café POI, which triggers a pop-up box with the POI name. This pop-up box works on POIs at any zoom range. Tip: In some urban areas, busin[...]

32 Two Position Formats map page option. In pages that have two major windows (such as two maps) you can tog- gle back and forth between the two windows by pressing PAGES | PAGES . Each time you switch between the windows, Active Map will be displayed at the top of the active window. Pages Menu with Two Map option selected (left). Map Page with two[...]

33 Press an arrow key parallel to the centerline to switch between hori- zontal and vertical layout. Press EXIT to clear the four flashing arrows. Fig. 1. Two Maps page display with four flashing arrows on the divid- ing centerline. Fig. 2. The centerline has been moved down to enlarge the top map, which is now zoomed in to 40 miles. Fig. 3. Pressi[...]

34 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna module. Make sure the MMC is in. (See comp[...]

35 Find Your Current Position Finding your current position is as simple as turning on the unit. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: Clear sky conditions means open sky, unobstructed by terrain, dense foliage or structures. Clouds do not [...]

36 The selected wreck (the Empress) to the southeast is 12.81 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject. On most items, a pop-up box will give the name of the se[...]

37 1. After the unit has acquired a position, press WPT | ↓ to POI- R ESTAURANTS . 2. You could search the entire restaurant category, but in this example we will narrow our search. Press → ↓ to F AST F OOD C HAINS | ENT | ↓ to N EAREST | ENT . 3. A list of restaurants will appear with the closest at the top of the list, and the one furthes[...]

38 5. The POI information screen appears. (This is how you can use this unit as a business phone directory!) If you wanted to navigate there, you could by pressing Enter. The Go To waypoint command is already highlighted. But we just want to see it on the map, so press ↓ to F IND O N M AP | ENT . 6. The unit's map appears, with the cursor cr[...]

39 MapCreate software. When you want to repeat a trip, these archived waypoints can be reloaded into your GPS unit. To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint. Create Waypoint at Current Position While you are traveling, press WPT | WPT . The waypoint is save[...]

40 Sequence for setting a waypoint. Step 1: while traveling, press WPT to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: vehicle continues on its way; number waypoint symbol is visible on map. Create Waypoint on Map 1. Use the arrow keys to move the cursor to the place wher[...]

41 4. Press ↓ to L ONGITUDE | ENT . Enter the longitude by pressing ↑ ↓ to change the first character, then press → to the next character and repeat until the longitude is correct. Press ENT , then EXIT | EXIT to return to the previous page display. The waypoint is saved and automatically given a name with a sequential number, such as waypo[...]

42 Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This unit has a man overboard feature that shows navigation data to the location where the feature was activated. To activate it, press the ZOUT and ZIN keys at the same time. Your posi- tion at the time these keys ar[...]

43 Navigate to Cursor Position on Map The G O T O C URSOR command navigates to the current cursor position on the map. It is a quick way to navigate to anything you can see on the map display. 1. Use the cursor with the zoom in and zoom out keys to move around the map until you find a location you want to go to. 2. Center the cursor over the locati[...]

44 The 60-mile zoom figure (left) shows the red course line connecting the current position to the destination. The Navigation Page (right) will also show navigation information. To stop navigating to the cursor, use the Cancel Navigation command. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT . The unit stops showing navi[...]

45 The unit is set to automatically create and record a trail when it is turned on. The unit will continue recording the trail until the length reaches the maximum trail point setting. The default is 2,000 points, but the unit can record trails 9,999 points long. When the point limit is reached, the unit begins recording the trail over itself. With[...]

46 Tip: Another quick way to stop recording one trail and begin a new one is to use the New Trail command. Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of completely turning off trail record- ing, under the trail Options command. If, however, the Update Active Trail option is left turned off, it will cancel[...]

47 Visual Trailing 1. On the Map Page, zoom ( ZIN or ZOUT ) so your trail is visible. 2. Begin moving and watch the Map Page. Walk or steer so your cur- rent position arrow traces along the trail you have just made. Tip: Generally, when using this method, the smaller the zoom range, the more accurately you will be able to steer along the trail. Nav[...]

48 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 2. A trail is always con- verted to a route when you navigate the trail. On the Map Page, the trail you are navigating is represented by a ma- genta line when the visib[...]

49 Navigate trail: Driver is heading southeast straight toward trail point 3 (left). Driver has reached point 3 and has turned southwest to follow the trail (right). Navigate trail, navigation page (compass rose) views: Driver is heading north straight toward trail point 3 (left). Bearing arrow shows the bearing to the trail point is 355 degrees. D[...]

50 NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and let your unit guide you. 6. When you reach your destination, be sure to cancel your navigation. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT [...]

51 1. Insert the MMC into your unit. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to T RANSFER M Y D ATA | ENT . 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must insert a card into the unit to activate the Load or Save commands. To transfer data from the unit to the[...]

52 These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach your destination or at any other time by using the Cancel Navigation com- m an d . Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT . F[...]

53 Section 4: Advanced GPS Operations Find Distance Current Position to Another Location 1. While on the Map Page press MENU | ↓ to F IND D ISTANCE | ENT . 2. Center the cursor crosshairs on the position you want to find the dis- tance to. A rubber band line appears, connecting your current position to the cursor's location. The distance alo[...]

54 Icons Icons are graphic symbols used to mark some location, personal point of interest or event. They can be placed on the map screen, saved and re- called later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols to choose from when creating an icon. Icons are similar to waypoints, [...]

55 Delete icons menu. 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL or D ELETE F ROM M AP and press ENT . 3. The Delete All Icons confirmation message will appear. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol[...]

56 A route allows you to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint. Once programmed into the GPS unit, a route provides the option of navigat- ing forward through the route waypoints or in reverse order. You can even begin navigating in the middle of a route. Create and Save a Route You [...]

57 Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 2. Press ↑ to N EW R OUTE , then press ENT . (To add to an existing route, press ↓ ↑ to route name | ENT .) 3. Press ↓ to E ND OF R OUTE | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with the cursor showing. 4. Use the Zoom and arr[...]

58 Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth. Fig. 5. Waypoint (4) set further south along the beach, at a rec- ognizable landmark (Bob Hall Pier). Waypoint PLFM Q W ends the route at an oil platform some distance from the shore. Fig. 6. Press EXIT to save the route and you return to this screen. 6. Move the cursor [...]

59 Edit a Route Name 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Highlight Saved Route Name | ENT | ↑ to Name | ENT . 3. Press ↑ ↓ to change the first character, then press → to move to the next character and repeat until the name is correct. Press ENT . To r[...]

60 Route Planning command on Main Menu (left). Routes menu (center). Edit Route menu (right) with Navigate Route command selected. 2. Press ↓ to select saved route name | ENT . Highlight N AVIGATE and press ENT . 3. Upon arrival at your destination, cancel navigation. Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ← to Y ES | ENT . Navi[...]

61 In Fig. 3 the traveler has turned northeast on his new course and is heading straight for Wpt 2, which is 0.20 miles away. Fig. 4 shows route navigation on the Map Page. In this figure, the traveler has reached Wpt 2 and is starting on the leg between Wpts 2 and 3. Navigate a Route in Reverse Here's how you run a route backward, from the en[...]

62 Trails Delete a Trail This is the command used to erase or delete a trail. Press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | → to D ELETE T RAIL | ENT | ← to Y ES | ENT . To Delete all trails at once : 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press → to D ELETE A LL | ENT | ← to Y ES | ENT . Edit a Trai[...]

63 Edit a Trail Pattern To edit a trail pattern press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ↓ to P ATTERN | ENT . Press ↑ ↓ to change the first character, then press → to the next character and repeat until the pattern is cor- rect. Press ENT . To get back to the main page press EXIT repeatedly. Edit Trail Menu [...]

64 Waypoints Delete a Waypoint To delete a waypoint from the waypoint list press WPT | ↑ to M Y W AYPOINTS | ENT | ↓ to Name | ENT . Press ↑ ↓ to select the desired charac- ter then press → to choose the next character. After the desired way- point is highlighted in the list, press ENT | ENT . Use ↓ to select D ELETE W AYPOINT then pres[...]

65 2. Latitude: press → to L ATITUDE | ENT . Press ↑ ↓ to change the first char- acter, then press → to the next character and repeat until the latitude is correct. Press EXIT . 3. Longitude: press ↓ to L ONGITUDE | ENT . Press ↑ ↓ to change the first character, then press → to the next character and repeat until the lon- gitude is [...]

66 4. Press ← ↓ to D ISTANCE | ENT . Press ↑ ↓ to change the first character, then press → to the next character and repeat until the distance is cor- rect. Press ENT . 5. Press ↓ to B EARING | ENT . Press ↑ ↓ to change the first character, then press → to the next character and repeat until the bearing is correct. Press ENT . 6. [...]

67 Section 5: System & GPS Setup Options Alarms This unit has three GPS alarms: Arrival Alarm, Off Course Alarm and Anchor Alarm — the only one of the three set to Off by default. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint. For example, if you have the arrival alar[...]

68 satisfied with the distance setting. If you want to enable the other alarms, repeat steps 2 and 3. 4. Press EXIT repeatedly to get back to the main page display. IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even when you are sitting still. This usually happens when using small — less than .05 mile — anchor alarm ra[...]

69 Menus for changing Com Port settings. For assistance in configuring the unit to communicate with another device, consult the factory. Customer service phone numbers are in the back of this manual. Also see the entry below for Configure NMEA . Configure NMEA You can configure the unit to use specific NMEA sentences. 1. Press MENU | MENU | ↓ to [...]

70 • VLW transmits the distance traveled through water as meas- ured by the paddle wheel. • VHW transmits the water speed as measured by the paddle wheel. 4. When the desired prefixes are turned on, press EXIT repeatedly to get back to the main page display. Coordinate System Selection The Coordinate System Menu lets you select the coordinate s[...]

71 The Military Grid Reference System (MGRS) uses two grid lettering schemes, referred to as standard and standard + 10 MGRS on this unit. Your position and datum in use determines which one to use. If you use standard and your position is off significantly, then try the alternate. NOTE: When the position format is changed, it affects the way all p[...]

72 The Data Viewer menu has four categories: GPS Data, Navigation, Trip Calculator and Time. Each category has its own data option menu. Ground Speed flashing on Two Position Map page (left). Data Viewer menu with no open categories (center). GPS data category opened with Ground Speed selected (right). 2. Select a data category. If the desired cate[...]

73 GPS Setup Menu (left). GPS Simulator menu (center). Map Page showing Steer with Arrows dialog boxes (right). The trav- eler is following a track of 144º at a speed of 71 miles per hour. Choose the desired settings, then turn on the simulator by highlighting the GPS S IMULATOR O N box and pressing ENT . Press EXIT repeatedly to get back to the m[...]

74 Tip: You can pick any spot on the map to begin a simulation by using the Initialize GPS command. It allows you to move the position ar- row to any location on the map. The command is detailed below. Initialize GPS In simulator mode, the Initialize GPS command makes the unit operate as if it is sitting someplace other than its actual location. So[...]

75 Map menu (left). Map Data menu (right). From the Map Page, you can access the Map Data menu by pressing MENU | ↓ to M AP D ATA | ENT . Earth Map Detail From the Map Data menu, highlight E ARTH M AP D ETAIL and press ENT . Select the desired level of map detail from four options: Off, Low, Me- dium or High. After the option is set, press EXIT .[...]

76 in diameter (same as the zoom range). The second smaller ring is 50 miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the ring's radius) is 25 miles (always 1/4 the zoom range). With the map cursor, you can scroll over to see the third and fourth rings. In this example, the distance [...]

77 GPS Setup Menu (left). Map Datum Menu (right). Map Detail Category Drawn This menu determines what mapping features are shown on the screen. This includes, waypoints, trails, icons, cities and highways, etc. You can turn on or off any of these items, customizing the map to your needs. Map Menu (left). Map Categories Drawn Menu (right). To get to[...]

78 on the map. It then shows the present position as distance on the map from that reference point. For example, if it shows a distance of UP 4.00" and LEFT 0.50", you then measure up four inches and to the left a half-inch from the refer- ence point on the map to find your location. To configure a map fix: To use this format, you need to[...]

79 Press → to S ELECT O RIGIN | ENT to bring up the waypoint and POI list. Select the waypoint (or a landmark of POI) you saved the reference point under and press ENT | ENT . Spell out the name of the waypoint, landmark or POI in the Find By Name box or press ENT to select the item from the list below. Highlight the waypoint, landmark or POI and[...]

80 To change map orientation from the Map Page, press MENU | ↓ to M AP O RIENTATION | ENT . Use ↑ ↓ to select the desired mode, then press ENT . Press EXIT | EXIT to return to the page display. Map Menu (left). Map Orientation menu with the North Up selected (right). NOTE: In North Up and Course Up, the present position arrow appears in the c[...]

81 To view Chart Note information: 1. Use the arrow keys to move the cursor over a Chart Note icon. When it's selected, a pop-up name box appears. 2. Press WPT to display the Note Information screen. 3. To scroll through the Chart Note screen, use ↑ ↓ arrow keys to read the information. To return to the main page display, press EXIT repeat[...]

82 NauticPath chart showing Port Services icon selected by cursor. When first highlighted, the Pop-Up name box appears. Tidal Current Information NauticPath charts contain Tidal Current information, represented at large zoom ranges by a box icon with the letter " C ." These icons will appear when you are zoomed in to a 6-mile range. The i[...]

83 NauticPath chart showing Tidal Current Station icon selected by cur- sor (left). Icon animates automatically at .08-mile zoom range (right). Current Information screen. The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time. The graph at the top of the screen is an approximate vie[...]

84 To select another date: 1. Use ← → to highlight month, day or year, then press ENT . 2. Use ↑ ↓ to select the desired month, day or year and press ENT . To clear the information screen, press EXIT . Tide Information NauticPath charts contain Tidal Information, represented at large zoom ranges by a box icon with the letter " T ."[...]

85 Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time. The graph at the top of the screen is an approximate view of the tidal range pattern for the day, from midnight (MN) to noon (NN) to midnight (MN). The dotted line across the graph is the Mean Lower Low Water line (ML[...]

86 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Select the Map Name , then press ENT | EXIT | EXIT . WARNING: You should never format the MMC containing your Navionics chart. Formatting the MMC will permanently erase the chart from the card. Overlay Data On any Page display except Satellite Status, you ca[...]

87 Every Page display has a maximum number of items you can show us- ing the Overlay Data command. To remove overlaid data: 1. While on the Page that shows the data you want to remove, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You will see a list of the overlay data currently displayed. Select the item you want to remove from the display and pr[...]

88 To change displayed data font size: 1. From the Map page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ ↑ to select a data type to resize, then press ← → scroll through five data size options: Off, Small, Medium, Large and Enor- mous. Press EXIT . The selected data type will be displayed in the new size. Map Page showing Ground S[...]

89 System Setup Menu (left) with Pop-up Help highlighted. Pop-up Help message for the Map Data (right). Reset Options To reset unit to factory defaults: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase any waypoints, routes, icons or plot trails. System Menu w[...]

90 To Require WAAS: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to R EQUIRE WAAS | ENT . 2. To return to the main page display, press EXIT | EXIT . 3. Repeat Step 1 to turn off WAAS requirement. Require WAAS command on GPS Setup Menu. Screen Contrast and Brightness To access the Screen menu, press MENU | MENU | ENT . The C ONTRAST slider b[...]

91 Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to S ET L ANGUAGE | ENT . 3. Use ↓ ↑ to select a different language and press ENT . Menu[...]

92 frequently lose and reacquire its lock on a WAAS satellite. That can result in the alarm repeatedly going off. If you want, turn off the WAAS Acquired/Lost alarm without affecting how the unit uses WAAS. To turn off WAAS alarm: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to S HOW WAAS A LARM . 2. Press ENT to turn it on (check) or turn [...]

93 To set Volume: Press ↓ to V OLUME . Use ← → to adjust the volume. To set Alarm Style: Press ↓ to A LARM S TYLE | ENT . Press ↑ ↓ to change the style and press ENT . After the option is set, press EXIT | EXIT to re- turn to the main page display. Sounds highlighted on main menu (left). Sounds menu (right). Track Smoothing This is a fa[...]

94 Main Menu (left). Trails Menu (center). Trail Options (right). General Trail Options To access the Trails Menu press MENU | MENU | ↓ to M Y T RAILS | ENT . Delete All Trails From the Trails Menu, press → to D ELETE A LL | ENT | ← to Y ES | ENT . Update Trail Option This menu lets you change the way the trail updates occur. From the Trails [...]

95 first character, then press → to the next character and repeat until the entry is correct. Press EXIT to return to the Trail Options Menu. Update Rate setting (left) and Update Distance setting (right). Trail Name highlighted (left). Edit Trail menu (center). Trails menu with New Trail highlighted (right). Specific Trail Options Delete Trail F[...]

96 Transparency set to 0 percent (left) and 50 percent (right). Transparency Use the transparency menu to adjust the transparency of menu win- dows. A high transparency setting allows you to continue monitoring the screen's display while working with a menu. A low transparency usually will make menu text easier to read, at the cost of watching[...]

97 Units of Measure This menu sets the speed, distance, depth, temperature and heading units. To change the units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT . To set Units of Measure: Select a category you would like to change. Highlight the desired unit of measure option under the category and press ENT . Repeat those steps for each ca[...]

98 Notes[...]

99 Section 6: Searching NOTE: The background map loaded in your unit lets you search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes. For a full set of searchable land features, including landmarks, streets, addresses and Points of In- terest, you must load your own high-detail custom m[...]

100 To search somewhere else, use the arrow keys to center the cursor crosshairs on the desired location. When the cursor is active, the unit always begins searching at the cursor location. In search results, the distance and bearing to the selected item will be calculated from the current position. In the case of a cursor search, the search result[...]

101 NOTE: We recommend you do not enter a city name unless the list you are given is too large when searching without it. This unit can actually search quicker without a city and you save time by not entering a city name. Find City field (left). Search in particular city only option (center). Find City by name (right). 6. When the necessary search [...]

102 8. To navigate to the address, press MENU select G O T O and press ENT . The unit will begin showing navigation information to the address. If you are only looking up an address, highlight F IND and press ENT . The map page will appear with the cursor crosshairs centered on the ad- dress. Tip: If the address happens to be an item in the Point o[...]

103 Find Any Item Selected by Map Cursor On the Map Page with a POI or map feature selected by the cursor press WPT. To return to the main page display, press EXIT . NOTE: Since the Go To waypoint command is highlighted, you can navi- gate to the selected POI by pressing ENT | EXIT while in the POI Waypoint Information screen. Find Interstate Highw[...]

104 Find By Name menu (left). Find Exit menu with exit selected (right). 3. Once you have selected a highway name you can select an exit. Press ↓ to switch to the Exit List, then press ↓ ↑ until you highlight the exit, then press ENT. 4. In the Exit Information screen you have two choices. A. Press ENT | ENT to navigate or go to the exit. B. [...]

105 Exit Information screen (left). General location and amenities information (right). Find Map Places or Points of Interest (POI) 1. Press WPT , use ↓ ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → to select a subcategory before pressing ENT .) You will be given two options: search by Name or by Ne[...]

106 Find by nearest option (left) with resulting POI list (right). 3. Search by name of POI. Highlight N AME and press ENT . There are two options: A. You can spell out the POI name in the top selection box. Press ↑ ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then pres[...]

107 Go To POI option (left). Find on Map POI option (right). Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command (left). Find Streets menu (right). 2. You must enter a street name in the First Street dialog box. Press ENT to display the Fi[...]

108 The Find Streets menu with the Find First Street command high- lighted (left). Streets Found list (center). Map Page showing results of a street search (right). The cursor points to the located street. 3. The Find Streets menu reappears with the street you are searching for in the First Street box. To search for that street, press ↓ to F IND [...]

109 B. Or you can jump down to the lower box and pick the second street from the selection list. Press ENT , then press ↓ ↑ to select a street from the list and press ENT . 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. You could now use similar techniques to select a city or Zip code, but your searc[...]

110 Find Waypoints 1. Press WPT | ↑ to M Y W AYPOINTS | ENT . 2. If searching for the nearest waypoint, select N EAREST and press ENT . If searching by name, highlight N AME and press ENT . (To search by name, jump to step 5.) Find By Nearest command (left). Find by Name command (center). List of the nearest waypoints (right). 3 . When you are se[...]

111 Find By Name menu (left). Waypoint Information screen (center). The cursor crosshairs are centered on the desired waypoint (right). A. To navigate to the waypoint, press ENT . The Go To Waypoint command is already highlighted. The unit will show navigation in- formation to the waypoint. B. To find the waypoint, press ↓ to F IND O N M AP | ENT[...]

112 Notes[...]

113 Section 7: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands Antigua Island Astro 1943; Antigua (Lee[...]

114 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Neth- erlands, Norway, Portugal, Spain, Sweden, Switze[...]

115 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Costa Rica, El Sal- vador, Guatemala, Honduras, Nicaragua North American 1927 Mean for Canada North American 1927 Mean for CONUS (Continen[...]

116 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic System 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad &a[...]

117 Notes[...]

118 Notes[...]

119 Notes[...]

120 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired opera- tion. Chan[...]

121 EAGLE DATABASES LICENSE AGREEMENT THIS IS a LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS a CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND EAGLE ELECTRONICS, a DIVISION OF LEI, THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANI[...]

122 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac- turer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use. The Da- tabases Limited Warranty app[...]

123 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac- turer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family, or household use. We warrant this produ[...]

124 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be re- turned, you must call cu[...]

Accessory Ordering Information for all countries To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate an Eagle deale[...]

Visit our web site: www.eaglesonar.com Eagle Pub. 988-0152-161 © Copyright 2005 All Rights Reserved Printed in USA 121905 LEI-Eagle [...]