Enviro C-11150 manuale d’uso

PELLET ST OVE Mini PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH Contact your building or fire officials about restrictions and installation inspection requirements in your area. SHERWOOD INDUSTRIES IS A[...]

2 Introduction................................................................................................................ ...................3 Rating Label Location................................................................................................................3 Safety W arnings And Recommendations...............................[...]

3 Introduction * This manual is designed for the technician in conjunction with the owner’s manual. * R ATING L ABEL L OCATION : The rating label is located on the back of the unit. S AFETY W ARNINGS A ND R ECOMMENDATIONS : Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these in[...]

4 Introduction SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger , the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed[...]

5 Introduction INSTALLATION: Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area. All local regulations, including those referring to national and Eur opean Standards need to be complied with when installing this appliance. Be sure to maintain the[...]

Inst alla tion D ECIDING W HERE TO L OCATE YOUR P ELLET A PPLIANCE : 1. Remo ve the right and left hand cabinet sides by loosening the three (3) T -20 T orx screws on the back of the each panel. 2. Remo ve the screw located on the front of the cabinet side, below the louvers and loosen the screw behind the ash door . 3. Using a 5 / 16 ” socket of[...]

7 Inst alla tion A PPLIANCE D IMENSIONS AND S PECIFICATIONS : Figure 2: Dimensions of Mini. 15 1 / 2 " (393 mm) 18 7 / 8 " (481 mm) 17 1 / 2 " (444 mm) 19 5 / 8 " (497 mm) 17 7 / 8 " (455 mm) 34" (864 mm) 18 1 / 2 " (470 mm) 22 1 / 8 " (562 mm) W eight (with full hopper): 238 lb (108 Kg) Hopper Capacity: up t[...]

Inst alla tion C LEARANCES TO C OMBUSTIBLES : IMPORTANT: Attach the Mini’ s Hearth P ad when installing the unit on a combustible floor . The supplied hearth pad meet all the r equirement of a proper hearth pad. If y ou do not use the supplied hearth pad a hearth pad must be used when on combustible material. A LCOVE C LEARANCES : This unit may b[...]

9 hot enough to cause burns if touched by children. Non-combustible shielding or guards ma y be required. 3. T ermination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe be installed outside when the appliance is vented directly through a wall, to create some natural draft to prevent the possibilit[...]

E XHAUST AND I NTAKE L OCATIONS : 10 1 / 16 " (255mm) 6 1 / 8 " (156mm) 2 1 / 16 " (53mm) Figure 8: Mini Inlet and Outlet Location. EXHAUST Base of unit to center of flue 10 1 / 16 ” (255 mm) Center of unit to center of flue 0” (0 mm) [at center of unit] FRESH AIR INTAKE. Base of unit to center of intake 6” (156 mm) Center o[...]

11 Figure 10: Corner Installation. C ORNER T HROUGH W ALL I NSTALLATION : 3" (75mm) 3" (75mm) W all thimble manufactured by pellet vent manufacturer . Inst alla tion M OBILE H OME I NSTALLATION : ENVIRO Mini 1 / 4 ” Lag Bolts Securely Fastened Ground Wire Directly to Metal Chassis Optional Hearth Pad Flooring Steel Frame ● Secure the [...]

Inst alla tion H ORIZONTAL E XHAUST T HROUGH W ALL I NSTALLATION : Vent installation: install vent at clearances specified by the vent manufacturer. A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor , or ceiling. Where passage through a wall or partition of combustible construction is [...]

13 Wall framing Wall thimble Termination cap Vertical section of vent pipe Horizontal frame for thimble 90° elbow Concrete Wall Clean out tee Wall framing Wall thimble Termination cap Vertical section of vent pipe Horizontal frame for thimble Clean out tee 90° elbow Wall strap Figure 13: V enting horizontally with rise. Figure 14: V enting with c[...]

                           ?[...]

15 Inst alla tion H EARTH M OUNT I NSTALLATION : Rain cap Storm collar Seal plate (cover plate) Existing masonry flue V ent pipe (single wall stainless flex pipe or solid PL vent) Fireplace damper location Clean out tee Existing fireplace Flexible vent connector (use this 5 foot [152cm] section of pipe to vent past fireplace damper or small shelf) [...]

Inst alla tion E XTERIOR M OUNTED E XHAUST B LOWER (20-070): The Mini can be equipped with an externally mounted exhaust blower . This optional kit includes al l components necessary to install the exhaust blower on any vertical w all surface. 1. Remove the left hand cabinet side by removing the two (2) screws down the front. Loosen the three screw[...]

17 Inst alla tion T YPICAL T HROUGH W ALL W ITH E XTERIOR B LOWER K IT I NSTALLATION - H ORIZONTAL T ERMINATION : Electrical Cable 90° Elbow 45°Elbow with Rodent screen or stainless steel termination hood 2ft (610mm) Riser Pipe Adaptor Exterior Blower and Housing W all Strap T o supply power to the exhaust blower Install the amour coated electric[...]

Roof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists V ent Pipe Exterior W all Sheathing Outside V ent T ermination Inst alla tion T YPICAL T HROUGH W ALL W ITH E XTERIOR B LOWER K IT I NSTALLATION - V ERTICAL T ERMINATION : F ollow the previous pages for through wall installations. Ensure that vent pipe is properly secured to wall usi[...]

19 Inst alla tion T HERMOSTAT I NSTALLATION : 1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the desired area. 2. Install a 12 or 24 V olt Thermostat using an 18 x 2 gauge wire from the unit to the thermostat. O PTIONAL S LIDER /D AMPER I NSTALLATION : If you wish to adjust the slider damper[...]

If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly , decreasing the air in the firebox. If , after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality i[...]

21 Inst alla tion O PTIONAL P ANEL K IT : This kit must be installed before the unit is started. Figure 32: Screws at back of the cab side. Figure 30: Screws above door top corner . Figure 31: Screw behind ash box. Tools Required: ●T -20 screwdriver Kit Components: Quantity Description 1 Left Cab P anel 1 Right Cab P anel 1 Hopper Lid 20 #8 T -20[...]

Inst alla tion 1 2 3 Figure 33: Installing Hopper Lid. Installing Hopper Lid: 1. Attach the hopper brackets to the back of the unit with a screw in each top holes of the brackets (#1 in Figure 33). Do not tighten these screws until all six (6) screws are in place. 2. Lay the hopper lid in place, slide the bushing into the bracket, and attach the li[...]

23 T roubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly . Only qualified technicians should deal with possible internal electrical failures. ● Do not remove f rom the firebox any screws without penetr ating oil lubrication. WHAT TO DO IF: 1. The st[...]

T roubleshooting ü P oor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational. ü Exhaust T emperature Sensor failure. – Bypass sensor located on Exhaust Blower if stov e now oper ates properly , the unit may require cleaning or a new sensor . Contact your local dealer for service. ü C[...]

25 T roubleshooting 7. The convection blower will not function normally. ü Clean all grill openings at the back and below unit . ü Press the fan button; does the fan come on? Press again to verify that the blower turns on; if , not contact your local dealer for service. 8. Ignitor- the pellets will not light. ü Everything else in the stov e oper[...]

W iring Diagr am Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown White White White White 115V White 220V Blue White White Orange Orange Orange Orange Yellow Yellow Grey Grey Grey Grey Purple Purple Blue 115V Black 220V Brown Black Black Black Blue Black Armor Cable Supplied Vacuum Switch Combustion Blower Optional Exterior Exhaust B[...]

27 P ar ts List Reference Number Description Part Number 1 120°F (49°C) Ceramic F an T emperature Sensor EC -001 2 Auger Motor - 115V EF-001 3 High Limit T emp Sensor 200°F (93°C) Manual Reset EF-016 4 V acuum Switch - 115V EF-017 Silicone Hose EF-018 Aluminum Hose Barb EF-019 Shoulder Bolt, Hardened Bushing & Nut (Set of 2) EF-124 Combusti[...]

P ar ts List Reference Number Description Part Number 17 Burn Pot 50-1166 18 Burn Pot Liner 50-1167 19 Burn Pot Bottom 50-1168 20 Front Louvers 50-1169 21 Lid Set 50-1171 22 Stove T op Assembly 50-1172 Hopper Guard 50-1174 23 Handle Bracket 50-1177 24 Draft Slider 50-1178 25 Door Assembly Complete 50-1179 26 Ash P an Cover 50-1180 27 Ash P an 50-11[...]

29 P ar ts Diagr am - Components Mini - Components November 2006                  [...]

P ar ts Diagr am - Steel Mini - Steel Components November 2006                      30[...]

31 W arr anty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by our Exclusive Lifetime Limited[...]

W arr anty Exclusions and Limitations: 1. This W arranty does not cov er tarnish, discoloration or wear on the plating or paint. 2. This W arranty excludes wear and tear or br eakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace. This Limited W arrant y covers defects in materials an[...]

33 W arr anty 17 . Damage to plated surfaces caused by fingerprints, scr atches, melted items, or other external scores and residues left on the plated surfaces fr om the use of abrasive cleaners or polishes is not cov ered in this warr anty . 18. The Limited W arranty does not co ver tarnish, discoloration or wear on the plated surf aces. 19. The [...]

34 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ NAME OF DEALER: _________________________________________ ADDRESS: _________________________________________ ____[...]