Extron electronic RGB 580xi AAP manuale d’uso

User ’ s Manual © 2008 Extron Electronics. All rights reserved. Hideaway ® Surface Access Products 68-604-01 Rev . F 08 08 HSA 400 & HSA 402 US/Domestic HSA 400 & HSA 402 International[...]

Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read In[...]

[...]

iii HSA 400/402 Series • Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the Hideaway Surface Access Products ...................................................................................... 1-2 Features ........................................................................[...]

iv HSA 400/402 Series • Table of Contents T able of Contents, cont’d HSA 400/402 Series Surface Access Pr oducts 1 Chapter One Intr oduction About the Hideaway Surface Access Products Features 68-604-01 Rev . F 08 08 All trademarks mentioned in this manual are the pr operties of their r espective owners.[...]

HSA 400/402 Series • Introduction HSA 400/402 Series • Introduction Introduction About the Hideaway ® Surface Access Products The patented Extron Hideaway HSA 400 and HSA 402 are furniture-mounted, architectural solutions for inconspicuous computer video interface connector access and control. The HSA 400 provides space for two double-space (d[...]

HSA 400/402 Series • Introduction Introduction, cont’d HSA 400/402 Series Surface Access Pr oducts 2 Chapter T wo Installation Installation Overview Preparing the Routing Template Preparing the Table and Mounting the Enclosure Cabling and Installing the AAPs Cabling the Enclosure Routing the AAP Cables Bezels 1-4 Projector Extron HSA 402 Extron[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation 2-3 Preparing the Routing T emplate Extron pr ovides a metal template for each HSA model at no charge . Appendix A lists the HSA 400/402 template part numbers. Extron r ecommends using this template as a guide to cut the hole in the table where the HSA will be inst[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation, cont’d 2-5 2-4 Preparing the T able and M ounting the E nclosure The preferr ed and recommended method for preparing the table is to use the appropriate Extron metal r outing template and a router . The templates are available at no cost . See the part numbers f[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation, cont’d 2-6 7 . Carefully lower the HSA enclosure into the hole to test the fit. If necessary , remove the enclosure and use a file or rasp to enlarge or smooth the edges of the opening. 8 . From the underside of the table, bolt the clamshell to the enclosure wit[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation, cont’d 2-8 3 . Insert each of the AAP’s screws through the holes in the AAP opening of the front panel. Secur e each AAP to the panel with the provided captive washers and #4-40 nuts (figure 2-5). Cable #4-40 Nut with Captive W asher F ront P anel RGB 580xi SI[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation, cont’d 2-10 HSA 402 H. SHIFT COMPUTER INPUT SELECT AUD IO RGB 580 xi SI AAP 120-240 50/60 Hz 5A 120-240 50/60 Hz 5A 3 1A 1B 1C 2 1D U nderside View Front P anel View 1A 1B 1C 1D Figure 2-7 — HSA 402 enclosure underside features 1 RJ-45 connectors — See “Ca[...]

HSA 400/402 Series • Installation HSA 400/402 Series • Installation Installation, cont’d Routing the AAP Cables The AAP cables must have freedom of movement to permit opening and closing the surface mount enclosure. At the same time, they need to be restrained to pr event their rubbing against the edges of the enclosure cable access hole in t[...]

HSA 400/402 Series • Installation Installation, cont’d HSA 400/402 Series Surface Access Pr oducts 3 Chapter Thr ee Maintenance and Modifications Replacing an AAP Replacing the Bezels Removing and Replacing the Enclosure Replacing the Gas Lift Adjusting the Top Surface Level 2-14[...]

Maintenance and Modifications HSA 400/402 Series • Maintenance and Modifications HSA 400/402 Series • Maintenance and Modifications 3-2 The HSA surface mount enclosures can be modified in the future to r eplace an AAP or to change the color or appearance of the bezel plug-ins. The most probable corr ective maintenance procedur es requir ed are [...]

HSA 400/402 Series • Maintenance and Modifications HSA 400/402 Series • Maintenance and Modifications Maintenance and Modifications, cont’d Replacing the Bezels The HSA ships with RJ-45/RJ-1 1 connector bezel plug-ins in a variety of colors and a black, blank bezel. Replace a bezel as follows: 1 . Remove the four hex head screws on the right [...]

HSA 400/402 Series • Maintenance and Modifications HSA 400/402 Series • Maintenance and Modifications Maintenance and Modifications, cont’d CA UTION The flanged edges of the top of the surface enclosure are bevelled to an ultra-fine thickness of less than 0.04 (4/100)" (approximately 1 mm). These edges are soft and can be easily nicked o[...]

HSA 400/402 Series • Maintenance and Modifications HSA 400/402 Series • Maintenance and Modifications Maintenance and Modifications, cont’d Replacing the Gas Lift The gas lift that raises the HSA surface is rated for 100,000 opening and closing cycles. Replace the gas lift as follows: Ensure that AC power is disconnected before servicing the [...]

HSA 400/402 Series • Maintenance and Modifications Maintenance and Modifications, cont’d HSA 400/402 Series Surface Access Pr oducts A Appendix A Reference Information Specifications HSA Part Numbers Included Parts Routing Templates Replacement Parts and Accessories Interface Accessories Top Plate Dimensions Templates 3-10 Adjusting the T op Su[...]

HSA 400/402 Series • Reference Information HSA 400/402 Series • Reference Information Reference Information A-3 A-2 Specifications General The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug types. See the Universal AC outlet guide on the Extron Web site, www.extron.com , for compatibility detail[...]

HSA 400/402 Series • Reference Information HSA 400/402 Series • Reference Information Reference Information, cont’d -or - A-4 HSA Part Numbers HSA 400 Part number HSA 400 USA Enclosure (black anodized finish) 60-415-01 HSA 400 International 60-700- nn HSA 402 Part number HSA 402 USA Enclosure (black anodized finish) 60-416-02 HSA 402 Internat[...]

HSA 400/402 Series • Reference Information HSA 400/402 Series • Reference Information Reference Information, cont’d T op Plate Dimensions The preferr ed and recommended method for cutting the table is to use the correct size metal r outing template (figure A-3 and chapter 2, “Installation” ) and a router . The templates are available at n[...]

HSA 400/402 Series • Reference Information HSA 400/402 Series • Reference Information Reference Information, cont’d A-9 C = 9.613 0.0325" (24.42 0.083 cm) Cut surface material out along this line. Cut-Out Radius: 0.25" (0.6 cm) Tilting Plate T op P anel Cut-Out T emplate for Extron's HSA 400 TEMPLA TE IS NO T FULL SIZE. User Ac[...]

HSA 400/402 Series • Reference Information Reference Information, cont’d HSA 400/402 Series Surface Access Pr oducts B Appendix B Packaging for Shipment A-10 International Model SURF A CE CUT -OUT AREA = 13.344 0.0325" (33.89 0.083 cm) x 5.925 0.0325" (15.05 0.083 cm) User Access (Connectors and AAP Openings) Cut surface material out [...]

HSA 400/402 Series • Packaging for Shipment HSA 400/402 Series • Packaging for Shipment Packaging for Shipment The HSA ’s ultra-fine machined surfaces and moving parts make them vulnerable to damage caused by mishandling during shipment if they are impr operly packaged. If, for any reason, you need to return an HSA to Extron, first contact Ex[...]

HSA 400/402 Series • Packaging for Shipment HSA 400/402 Series • Packaging for Shipment Packaging for Shipment, cont’d 6 . Install the plastic strips that protect the flanged edges of the top of the surface enclosure (figur e B-4). Figure B-4 — Installing protective strips 7 . Release (tilt up) the top panel. 8 . Insert the HSA and the clam[...]

HSA 400/402 Series • Packaging for Shipment HSA 400/402 Series • Packaging for Shipment Packaging for Shipment, cont’d 9 . Insert the opposite end of the clamshell into the r emaining foam shell (figure B-6). Firmly push the foam shells together as far as they will go to completely suspend the HSA and clamshell. The sides of the clamshell pro[...]

HSA 400/402 Series • Packaging for Shipment Packaging for Shipment, cont’d B-8 11 . HSA 400 US/domestic version only . These smaller HSAs in the foam shells do not fit snugly in the shipping carton. Pad either side with the extra foam that was included in the return kit. Insert the foam vertically in the carton’s corners on one side of the ca[...]