Ford 1999 F-350 manuale d’uso

Before driving Introduction 2 Instrumentation 5 Controls and features 22 Seating and safety restraints 82 Starting and driving Starting 107 Driving 112 Roadside emergencies 144 Servicing Maintenance and care 169 Capacities and specifications 212 Customer assistance 223 Reporting safety defects 235 Index 236 All rights reserved. Reproduction by any [...]

ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regardi[...]

SPECIAL NOTICES Notice to owners of diesel-powered vehicles Read the 7.3 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for information regarding correct operation and maintenance of your diesel-powered light truck. Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’ s Gu[...]

If your vehicle is equipped with the Ford ambulance preparation package, it will be indicated on the Certification label. The label is located on the driver’ s side door pillar or on the rear edge of the driver’ s door . Y ou can determine whether the ambulance manufacturer followed Ford’ s recommendations by directly contacting that manufact[...]

Instrumentation 5[...]

0 0000 00000 MPH 20 km/h 40 60 80 100 120 140 160 0 10 20 30 40 50 60 70 80 90 100 LOW FUEL DOOR AJAR BRAKE FUEL RESET LOW RANGE 4 X 4 ! ABS + - L E F H RPM 1000 X 0 1 2 3 5 6 4 PR N 2 1 8 C 18 H D FUEL FILL SERVICE ENGINE SOON O P ON COAST OFF P A N E L D I M SET ACCEL RES Headlamp control (pg. 22) Instrument panel dimmer switch (pg. 23) T urn sig[...]

1 2 3 4 5 6 F M 1 S T S C A N E J R E W F F S I D E 1 - 2 C O M P S H U F F L E T A P E C D D IS C S B A S S T R E B B A L F A D E A U T O S E T V O L - P U S H O N S E E K T U N E A M F M w A / C M A X A / C O F F O F F O F F O N P A S S E N G E R A I R B A G O V E R D R I V E W D 4 X 4 H I G H 4 X 4 L O W Passenger air bag deactivate switch (pg. [...]

W ARNING LIGHTS AND CHIMES Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information). The ignition must be in the ON position for this lamp to illuminate. The lam[...]

What you should do if the Check Engine/Service Engine Soon light illuminates Light turns on solid: This means that the OBD I system has detected a malfunction. T emporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly .) 2. Poor fuel qualit[...]

What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. T emporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly .) 2. Poor fuel quality or water i[...]

T ransmission control indicator light (TCIL) (if equipped) The word OFF located on the end of the gearshift lever is the transmission control indicator light (TCIL). The TCIL may flash steadily if a malfunction is detected. If the TCIL is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission [...]

T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter . High beams Illuminates when the high beam headlamps are turned on. Charging sys[...]

Door ajar Illuminates when the ignition is in the ON or ST ART position and any door is open. Oil pressure/Engine coolant This light will illuminate when the ignition is in the ON position and the: • engine coolant temperature is very high • engine oil pressure is low • engine is off The light serves as a notice that a system needs your atten[...]

GAUGES Fuel gauge Displays approximately how much fuel is in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of reserve fuel in the ta[...]

Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the e[...]

T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If t[...]

Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately . Check the oil level. Add oil if [...]

Mode control Each press of the MODE control will display a different feature as follows: A verage fuel economy . The display will indicate the vehicle’ s average fuel economy in liters/100 km (or miles/gallon) since the average fuel economy was last reset. If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometer[...]

• if the vehicle is started while parked on an incline. • if less than 30 liters (8 gallons) of fuel is added to the fuel tank. The fuel range function will flash for 5 seconds at the following distances based on fuel remaining and fuel economy calculations: • 80 km (50 miles) • 40 km (25 miles) • 16 km (10 miles) Off. In this mode the di[...]

Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the trip computer on the overhead console. 3. T urn ignition to the ON position. 4. Press and hold both trip computer controls. After approximately four seconds, the trip computer will enter zone setting mode. Zon[...]

Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Locate the trip computer located in the overhead console. 2. Start the vehicle. 3.[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or[...]

Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. 4WD CONTROL (IF EQUIPPED) This control oper[...]

AUXILIARY POWER POINT The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter . Use the power point. CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. T emperature control Controls the temperatur[...]

• (Panel) -Distributes outside air through the instrument panel registers. • OFF-Outside air is shut out and the fan will not operate. • (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. • (Floor) -Allows for maximum heating. Distributes outside air through the floor ducts. • (Floor and[...]

Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or a sudden stop. Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode sele[...]

• MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster . Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • A/C-Uses outside air to cool the vehicle. It is quieter th[...]

Operating tips • In humid weather , select before driving. This will reduce your windshield from fogging. After a few minutes, select any desired position. • T o prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position. • Don’t put objects under the front seat that will interfere with th[...]

USING YOUR AUDIO SYSTEM AM/FM Stereo AM/FM Stereo 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON AM / FM STEREO Controls and features 29[...]

V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in [...]

Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. W ith the electronic AM/FM stereo, press the TONE control once, then use the volume knob to adjust the level. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. W ith the electronic A[...]

Setting the clock Press CLK to toggle between listening frequencies and clock mode. T o set the hour , press and hold the CLK control and press: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch [...]

reverting back to the clock. In media mode, the media information will always be displayed. AM/FM stereo cassette V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS VOL - PUSH ON SEEK TUNE AM FM CLK 12 3 456 FM1 ST VOL - PUSH O[...]

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the A[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Pre[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker s[...]

T ape select • T o enter tape mode while in radio mode, press the T APE AMS control. Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. T o activate the feature, momentarily depress the T APE AMS button. Then, press either REW (f[...]

Dolby 姞 noise reduction Dolby 威 noise reduction operates only in tape mode. Dolby 威 reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby 威 noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock Pres[...]

• to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the [...]

V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned o[...]

Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD or CD changer (if eq[...]

Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.) T o stop on a particular selection, press the control again. Scan function in CD or CD changer m[...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Press the TREB control then press: • to decrease the treble output and • to increase the treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can[...]

T ape/CD select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • T o begin CD play (if CD(s) are loaded), press the CD control. The first track of the disc will begin playing. If r[...]

Eject function Press the EJ control to stop and eject a tape. Press the EJ control to stop and eject a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the noise reduction. Dolby noise reduction manufactured under license from Dolby Laboratorie[...]

Setting the clock T o set the hour , press and hold the CLK control and press SEEK: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK butt[...]

The CLK button will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media[...]

Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operatio[...]

AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play . AM/FM select in CD mode Press this control to stop CD play and begin radio play . Tune adjust The tune[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD changer (if equipped[...]

Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.) T o stop on a particular selection, press the control again. Scan function in CD mode Press the [...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Press the TREB control then press: • to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adju[...]

T ape/CD/CD changer (if equipped) select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • T o begin CD play (if CD(s) are loaded), press the CD control. The first track of the disc[...]

T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape and/or a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the noise reduction. Dolby noise reduction manufac[...]

Setting the clock Press the clock/RDS control until SELECT HOUR is displayed and press: • to decrease hours and • to increase hours. T o set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes. AUTO RDS SEL AUTO RDS SEL Controls and features 59[...]

Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or off. Press the control to scroll through the following selections: RDS traffic announcement • Press the RDS control until TRAFFIC is displayed[...]

RDS select program type • Press the RDS control until FIND program type is displayed. • Use the SEL control to select the program type. W ith the feature on, use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz/R&B • Religious • Rock • Soft ?[...]

• Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency . Press SEL in order to scroll through the text messages. Mute mode Press the control to mute the playing media. Press the control again to return to the p[...]

Press to eject the magazine. Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward. Depending on your system, you may insert up to six or ten CDs. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer . The magazine may be s[...]

T roubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • Y ou may be traveling on a rough road, playing badly scratched discs or the disc may be dirty . Skipping will not scratch the discs or damage the player . If your changer do[...]

• Do not expose tapes to direct sunlight, high humidity , extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. • T ighten very loose tapes by inserting a finger or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. • [...]

The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo. Audio system warranties and service Refer to the “W arranty Guide” for audio system warranty information. If service is necessary , see your dealer or a qualified technician. POSITIONS OF THE IGNITION 1.[...]

SPEED CONTROL (IF EQUIPPED) T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. T o turn [...]

T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if i[...]

Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. T o set a lower set speed • Press and hold CST/COAST . Release the control when the desired speed is reached or • Press and release CST/COAST . Each press will de[...]

T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. O N O F F Controls and features 70[...]

T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TIL T STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the[...]

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter . WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward [...]

FLASH TO PASS Pull toward you to activate and release to deactivate. OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy . The overdrive function allows automatic upshifts to second, third and fourth gear . Deactivating overdrive Press the T ransmission Control Switch (TCS) located[...]

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . Depress again to stop window operat[...]

Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) W ith accessory delay , the window switches may be used for up to ten minutes [...]

2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. CENTER CONSOLE (IF EQUIPPED) Y our vehicle may be equipped with a variety of console features. These inclu[...]

REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership[...]

Sounding a panic alarm Press this control to activate the alarm. T o deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)[...]

T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together . Illuminated entry The int[...]

Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: T o reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10[...]

T AILGATE LOCK (IF EQUIPPED) Y our vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • T urn ignition key to the left to unlock. T ailgate removal Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver t[...]

SEA TING Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the release lever to quickly fold the seatback forward. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched in[...]

Captain’ s chair (if equipped) • Lift the release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the seatback handle up to recline the seat. • Push the release lever down to quickly fold the seatback forward. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or [...]

Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support T urn the lumbar support control toward the front of vehicle to increase firmness. T urn the lumbar support control toward the rear of vehicle to increase softness. Seating and safety restra[...]

Rear folding bench seat (if equipped) Folding down the rear seats All safety belts should be properly stowed in the seat pockets before folding down the rear seat. Make sure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down. 1. Locate the strap on the rear of the lower sea[...]

1. Lift/rotate the seatback toward the rear of the vehicle and make sure it latches securely . 2. Lift/rotate the lower seat cushion to its seating position. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure childr[...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened[...]

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is insta[...]

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensiti[...]

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the w[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air [...]

Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably . • Recline the seat slightly (one or two degrees) from the u[...]

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activa[...]

Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger (if equipp[...]

Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF switch has been installed in this vehicle. Before [...]

In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. 2. The OFF light will briefly illuminate when the ignition is turned[...]

Always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF . This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury t[...]

• although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle; or • the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so t[...]

2. Child age 12 or under: A child age 12 or under must ride in the front seat because: • my vehicle has no rear seat; • although children age 12 and under ride in the rear seat whenever possible, children age 12 and under have no option but to sometimes ride in the front seat because rear seat space is insufficient; or • the child has a medic[...]

Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or[...]

A belt-positioning booster should be used if the shoulder belt rests in front of the child’ s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion. Y ou may wish to discuss the special[...]

• Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating[...]

Rear facing child seats should NEVER be placed in the front seats. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is n[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory . Contact the manufacturer of your child safety seat for information about ordering a tether strap. T et[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accele[...]

2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 4[...]

Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4[...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer , and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

Using RABS • In an emergency , applying full pressure may cause the front wheels to lock. If the front brakes lock, the vehicle cannot be steered. Yo u should apply the brakes with steadily increasing force, as if “squeezing” the brakes. If you feel the front wheels begin to lock, momentarily release the pedal and repeat the “squeeze” tec[...]

W ith the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately). Using ABS • In an emergency or when maximum efficiency from the ABS is required,[...]

Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency . Since the parking[...]

Extended use of other than the manufacturer’ s specified size tires on a T raction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver . T o avoid injury , never run the engine with one wheel off the ground, such as when changing[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your dealer or a qualified service technician. Driving with a 4–speed au[...]

N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . (Overdrive) can be deactivated by pressing the T ransmission Control Switch (TCS) on the[...]

2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear , and will s[...]

4. T urn ignition to position 5 (ST ART) to start the engine, let the engine idle for a few seconds, then shift into gear . 5. Release the brake pedal. 6. Release clutch slowly while pressing down slowly on the accelerator pedal. • Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standsti[...]

Maximum downshift speeds 1 6-speed transmission Shift from: T ransfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 26 km/h (16 mph) 4 - 3 56 km/h (35 mph) 19 km/h (12 mph) 3 - 2 32 km/h (20 mph) 13 km/h (8 mph) 2 - 1 8 km/h (5 mph) 3 km/h (2 mph) 1 - LO Only shift to LO when at a stop. 1 Use 2H or 4H for 4WD equipped[...]

2. Set parking brake. 3. Shift into 1 (First). 4. T urn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage [...]

W ith the 5-speed transmission you can shift into R (Reverse) only by moving the gearshift from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). This is a special lockout feature that protects you from accidentally shifting into R (Reverse) when you downshift from D (Overdrive). W ith the 6-speed transmission you can shift [...]

Removing key from ignition • T urn the ignition key until it stops. • Push the release lever forward and rotate the key towards you and remove. POWER TAKE OFF (PTO) CAPABILITY (IF EQUIPPED) Some vehicles with 6.8L and 7.3L engines are equipped with Power T ake Off (PTO) capability . These vehicles have a special transmission case, internal comp[...]

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving,[...]

• automatic hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK. Manual 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the front wheel hub lock control from FREE to LOCK, then manually engaging the transfer case with a floor -mounted shifter . 4WD system indicator lights The 4WD sy[...]

Shifting from 2H (2WD high) to 4H (4WD high) Engage the locking hubs by rotating the hub lock control from FREE to LOCK, then move the transfer case lever from 2H (2WD High) to 4H (4WD High). Do not shift into 4H (4WD High) with the rear wheels slipping. Shifting from 4H (4WD high) to 2H (2WD high) Move the transfer case lever to 2H (2WD High) at a[...]

4. Move the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 4L (4WD Low). Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. This position should only be[...]

Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 88 km/h (55 mph). • Do not shift into 4x4 HIGH with the rear wheels slipping. Shifting from 4x4 HIGH (4WD high) to 2WD (2WD high) Rotate the 4WD control to 2WD at any forward speed. Y ou do not need to put the gearshift in R (Revers[...]

4. Move the 4WD control to the 4x4 HIGH or 4x4 LOW position. Driving off-road with 4WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in r[...]

Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water , drive slowly . T raction or brake capability[...]

If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically . Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km/h (30 mph). Automatic transmissions may shift frequently while driving up steep g[...]

• GVWR (Gross V ehicle W eight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’ s door pillar . • GA WR (Gross Axle W eight Rating) : Carrying capacity for each axle system. The GA WR is specific to eac[...]

weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (F ARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e. restrict the number of passengers or amount of cargo carried).[...]

Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage. T OWING A TRAILER Y our vehicle may tow a Conventional/Class IV trailer or fifth wheel trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and[...]

T railer towing tables F-250 with manual transmission Engine Rear axle ratio Maximum GCWR-kg (lbs.) Maximum trailer weight-kg (lbs.) 1 5.4L 3.73 6 124 (13 500) 4 536 (10 000) 5.4L 4.10 6 804 (15 000) 4 536 (10 000) 6.8L 3.73 7 484 (16 500) 4 536 (10 000) 6.8L 4.30 8 165 (18 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only . Fifth whee[...]

F-350 with automatic transmission Engine Rear axle ratio Maximum GCWR-kg (lbs.) Maximum trailer weight-kg (lbs.) 1 5.4L 3.73 6 124 (13 500) 4 536 (10 000) 5.4L 4.10 6 804 (15 000) 4 536 (10 000) 6.8L 3.73 7 711 (17 000) 4 536 (10 000) 6.8L 4.30 9 072 (20 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only . Fifth wheel trailer maximum we[...]

Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’ s bumper or attach to the axle. Y ou must distribute the load in your trailer so that 10% of the tot[...]

T railer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system. Y our vehicle may not have enough[...]

Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. T railer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When tu[...]

• 4x2 vehicles must have the driveshaft removed if the rear wheels are to be kept on the ground. If only the front wheels will be on the ground, the driveshaft does not need to be removed. • 4x4 Electronic Shift on the Fly vehicles cannot be towed with any wheels on the ground. • 4x4 vehicles with a manual shift (floor -mounted) transfer case[...]

• After installing a snowplow to the vehicle, ensure the vehicle’ s front toe alignment and front ride height are within specification (reset if required). These specifications are located in the vehicle’ s W orkshop Manual. Adherence to the toe, tire pressures and ride height specification is important for proper tire wear , ride, handling a[...]

Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer . Engine temperature while plowing When driving with a plow , your engine may run at a higher temperature than normal because the attached snowplow blade will restrict airflow to the radiator . If you are dri[...]

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously . • Depress control again to [...]

Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the OFF posi[...]

Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

T o remove a fuse use the fuse puller tool provided on the fuse panel cover . The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 20A Electronic Flasher 2 5A Instrument Cluster , Powertrain Control Module (PCM) Keep Alive Memory 3 20A Cigar Lighter , OBDII 4 10A Glove Box Lamp, Map Lamps, Power Mirrors, Underhood Lamp [...]

Fuse/Relay Location Fuse Amp Rating Description 8 5A Radio, Headlamp Switch Illumination 9 — Not Used 10 — Not Used 11 10A W asher Pump, W iper Run/Park Relay Coil, W iper Hi/LO Relay Coil, W asher Pump Relay Coil 12 15A Horn 13 20A Stop Lamps, Center High-mount Stop Lamp, T railer T ow Stop Lamp 14 10A Dome Lamp, Cargo Lamp, Courtesy Lamps 15 [...]

Fuse/Relay Location Fuse Amp Rating Description 27 10A Ignition Run Power Feed (Customer Access) 28 10A Brake Shift Interlock, DRL Relay Coil, Speed Control Module, Backup Lamps, T railer T ow Backup Lamp Relay Coil, Electronic Shift On The Fly Hub Lock Solenoid 29 5A Instrument Cluster (Charge and Airbag W arning Lamps) 30 30A PCM Relay Coil, Igni[...]

The high-current fuses and relays are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 7.5A * T railer T ow Left Stop/T urn Lamp 2 10A* Air Bag Module 3 7.5A* T railer T ow Right Stop/T urn Lamp 4 20A* T railer T ow Backup Lamps, T railer T ow Park Lamps 5 20A* (Gasoline only) 5A* (Diesel only) Gasoline only-PCM, T wo Speed Fuel [...]

Fuse/Relay Location Fuse Amp Rating Description 7 20A* (Gasoline only) 5A* (Diesel only) Gasoline only-V apor Managment V alve, HEGO Sensors, Intake Manifold Communication Control, EVR Solenoid, PCM, Canister V ent Solenoid Diesel only-Dual Alternator ⬙ A ⬙ Field 8 15A* T railer T ow Electronic Brake Illumination, Park Lamps, T railer T ow Park[...]

Fuse/Relay Location Fuse Amp Rating Description 27 - (Gasoline only) 30A* (Diesel only) Gasoline only-Not Used Diesel only-Injector Driver Module 28 30A** T railer T ow Electronic Brake Controller 29 20A** Radio 30 -- PCM Power Relay 31 -- Blower Motor Relay 32 -- T wo Speed Fuel Pump Relay (Gasoline only), Injector Driver Module Power Relay (Diese[...]

If your vehicle is equipped with 4WD, a spare tire of a different size than the road tires should not be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: T ool Location Spar[...]

2. The following steps are required to move the support bracket (if equipped) away from the spare tire: • W ith tapered end of lug wrench, loosen the eyebolt on the support bracket. • Line up the eyebolt with the slot in the support bracket. • Slide the support bracket off the eyebolt and move the support bracket away from the spare tire. 3. [...]

5. The following steps are required to secure the support bracket (if equipped) under the spare tire: • Move the support bracket over the spare tire. • Slide the support bracket over the eyebolt into the slot on the support bracket. • T ighten the eyebolt with tapered end of lug wrench leaving it positioned at a right angle of the slot on the[...]

5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual [...]

• Front (4x2) • Front passenger side (4x4) Roadside emergencies 157[...]

• Front driver side (4x4) Make sure the jack fits into the notched area on the differential housing. • Rear Roadside emergencies 158[...]

8. T urn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 9. Remove the lug nuts with the lug wrench. 10. On single rear wheel vehicles, replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front tires and vehicles equipped with single rear w[...]

• Front (4x2) • Front driver side (4x4) • Front passenger side (4x4) Roadside emergencies 160[...]

• Rear 14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’ s rated capacity . 16. Remove the lug nuts with the lug wrench. 17. Replace the fl[...]

The following steps apply to all vehicles: 19. Remove the jack and fully tighten the lug nuts in the order shown. 20. Stow the flat tire. Refer to Stowing the spare if the vehicle is equipped with a spare tire carrier . 21. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 22. Unb[...]

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt [...]

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + [...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift or a slingbelt with T -hooks. On 4x4 vehicles, it is [...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood. Slide the handle to release the auxiliary latch. 3. Lift the hood until the lift cylinders hold it open. Main[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid reservoir 4. Power distribution box 5. Power steering fluid reservoir 6. Air filter assembly 7. Engine coolant reservoir 8. W indshield washer fluid reservoir 9. Battery 10. Engine oil filler cap 11. T ransmission f[...]

2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipst[...]

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the MIN and MAX ranges, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine[...]

Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting [...]

2. Visually inspect the fluid level. 3. If necessary , add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter . Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you[...]

1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir . WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid [...]

ENGINE COOLANT Check the level of the engine coolant in the reservoir . Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter . If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empt[...]

• DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’ s cooling system. • The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’ s engine cooling system. • Use only the type of coolant with which your[...]

Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components. Always dispose of used [...]

How fail-safe cooling works If the engine begins to overheat: • the engine coolant temperature gauge will move to the red (hot) area. • the symbol will illuminate. • the symbol will illuminate. • the Service Engine Soon indicator light will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically[...]

Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the “Service Guide” for the service interval schedules. If adding fluid is necessary , use only MERCON 威[...]

operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking [...]

The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating [...]

Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use only fluid that [...]

Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter . DRIVELINE UNIVERSAL [...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte l[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sa[...]

INFORMA TION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set. T ire Quality Grades apply to new pneumatic tires for use on passenge[...]

T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire li[...]

• Four tire rotation • Five tire rotation Maintenance and care 192[...]

Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only the tire co[...]

The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used as chains may chip aluminum wheels. Follow these guidelines when using snow tires[...]

Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gas[...]

When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fue[...]

with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particula[...]

4. T o install the cap, align the tabs on the cap with the notches on the filler pipe. 5. T urn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel fille[...]

driving (engine break-in period). Y ou will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this “Owner Guide.” The advertised capa[...]

5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel [...]

• Resting your foot on the brake pedal while driving may reduce fuel economy . • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant Spec[...]

It is important to note the box in the lower left corner of the window sticker . These numbers represent the Range of Km/L (MPG) expected on the vehicle under optimum conditions. Y our fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control componen[...]

sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’ s emission system is on the V ehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and give[...]

• T ail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs (aerodynamic) Handle a halogen headlamp bulb carefully and keep out of children’ s rea[...]

Replacing headlamp bulbs (sealed beam) T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws and parking lamp/side marker assembly by pulling gently 4. Disconnect the electrical connectors from the parking lamp/side marker assembly and remove. 5. Remove the four bolts and headlamp [...]

Replacing tail lamp/Backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the tail lamp assembly . 3. Carefully pull the lamp assembly from[...]

T o install the brakelamp assembly: 1. Install the bulb into the lamp assembly and rotate clockwise. 2. Install the lamp assembly on the vehicle with two screws. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb.[...]

AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision. • The headlamp beams are pointed substantially[...]

W axing your vehicle W ax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs before waxing vehicle. Use tar remover to remove any tar spots. A void getting wax on the wind[...]

Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps W ash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary . T o avoid scratchin[...]

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an[...]

MOTORCRAFT PART NUMBERS Component* 5.4L V8 engine 6.8L V10 engine Air filter element F A-1634 F A-1634 Fuel filter FG-986B FG-986B Oil filter FL-820-S FL-820-S PCV valve EV -233 EV -233 Battery (Standard) BXT -65-650 BXT -65-650 Battery (Optional) BXT -65-750 BXT -65-650 Spark plugs-platinum** A WSF-22E A WSF-22E *Refer to the 7.3 Liter Power Strok[...]

Fluid Ford Part Name Application Capacity Engine coolant 5 Premium Engine Coolant 5.4L V8 engine without A/C 16.9L (17.9 quarts) 5.4L V8 engine with A/C 18.4L (19.4 quarts) 6.8L V10 engine 29.0L (30.6 quarts) Engine oil (includes filter change)- Gas engines Motorcraft 5W -30 Super Premium Motor Oil All 5.7L (6.0 quarts) Engine oil (includes filter [...]

Fluid Ford Part Name Application Capacity T ransmission fluid 3 Synthetic MERCON 威 AT F 5-speed manual 3.2L (3.4 quarts) Motorcraft MERCON 威 AT F 6-speed manual 5.5L (5.8 quarts) Automatic - 4R100 with small cooler (vehicles equipped with 20 oil-to-air - plate cooler) 16.1L (17.1 quarts) 4 Automatic - 4R100 with large cooler (vehicles equipped [...]

LUBRICANT SPECIFICATIONS Item Ford part name or equivalent Ford part number Ford specification Front axle (4X4) Motorcraft SAE 75W90 Axle Lubricant XY -75W90-QL WSP-M2C201-A Rear axle Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lube 1 F1TZ-19580-B WSL-M2C192-A Motorcraft SAE 75W90 Synthetic Rear Axle Lube 1 (Dana 80 axles) XY -75W90-[...]

Item Ford part name or equivalent Ford part number Ford specification Hinges, latches, striker plates, fuel filler door hinge and seat tracks Multi-Purpose Grease DOAZ-19584-AA or F5AZ- 19G209-AA ESB-M1C93-A or ESR-M1C159-A T ransmission /steering/parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Premium Long-Life Grease[...]

ENGINE DATA Engine 5.4L V8 engine 6.8L V10 engine Cubic inches 330 415 Horsepower 235 @ 4250 rpm 275 @ 4250 rpm T orque 335 lb.-ft. @ 3000 rpm 410 lb.-ft. @ 2650 rpm Required fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) 1.3-1.4 mm (0.052-0.056 inch) Ignition system Coil on p[...]

F250-Crew cab Dimension Body style Crew Cab 4x2 Crew Cab 4x4 (1) Overall height 1 960 mm (77.2 in) a / 1 883 mm (74.1 in) b 2 053mm (80.8 in) a / 2 052 mm (80.8 in) b (2) T rack (Front / Rear) 1 745 mm (68.7 in)/ 1 729 mm (68.1 in) a,b 1 736 mm (68.4 in)/ 1 729 mm (68.1 in) a,b (3) Overall width 1 988 mm (78.3 in) a,b 1 988 mm (78.3 in) a,b (4) Whe[...]

(5) Overall length 5 732 mm (225.7 in) 5 754 mm (226.5 in) 5 879 mm (231.4 in) a / 6 288 mm (247.6 in) b 6 291 mm (247.7 in) a Short wheel base b Long wheel base c Single rear wheels d Dual rear wheels F350-Crew cab Dimension Body style Crew Cab 4x2 Crew Cab 4x4 (1) Overall height 1 929 mm (75.9 in) 2 038 mm (80.2 in) (2) T rack (Front / Rear) 1 74[...]

(4) Wheelbase 3 576 mm (140.8 in) 4 186 mm (164.8 in) 4 475 mm (176.2 in) 4 475 mm (176.2 in) (5) Overall length 5 732 mm (225.7 in) a 6 341 mm (249.6 in) b --- a Short wheel base b Long wheel base F550 Dimension Body style Chassis Cab 4x2 Chassis Cab 4x4 Crew Cab 4x2 Crew Cab 4x4 (1) Overall height 2 076 mm (81.7 in) 2 075 mm (81.6 in) 2 067 mm (8[...]

3 2 1 5 4 Capacities and specifications 221[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. V ehicle identification number [...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Ford extended service plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides: • Protection against repair co[...]

Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs. Certain warra[...]

Please have the following information available when contacting Ford Customer Assistance: • Y our telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number[...]

• sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’ s performance as designed • a request for reimbursement of consequential expenses unless a service or product concern being reviewed • items not covered by the New V ehicle Limited W arranty (including maintenance and wea[...]

Y our dealership and a Ford Motor Company representative are asked to submit statements at this time. T o properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the year , make, model, and V ehicle Identification Number (VIN) listed on your [...]

the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law . T o Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board[...]

FORD MOTOR COMP ANY WORLDWIDE DIRECT MARKET OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. T elephone: (313) 594-4857 F AX: (313) 390-0804 If you are in another foreign country , contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affi[...]

A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made fro[...]

T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running [...]

Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates T ailgate covers T ailgate [...]

• The Federal Communications Commission (FCC) and Canadian Radio T elecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and shou[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Accessory delay .......................... 75 Air bag supplemental restraint system .......................... 92 and child safety seats .............. 93 description ................................ 92 disposal ...................................... 96 driver air bag ............................ 94 indicator light ......................10,95 opera[...]

Ford Extended Service Plan ... 224 Getting assistance outside the U.S. and Canada ..................... 229 Getting roadside assistance ... 223 Getting the service you need ... 225 Ordering additional owner’s literature ................................. 234 The Dispute Settlement Board ... 226 Dipstick engine oil .................................[...]

GA WR (Gross Axle W eight Rating) ..... 132 calculating ............................... 134 definition ................................. 132 driving with a heavy load ...... 132 location .................................... 132 GVWR (Gross V ehicle W eight Rating) ..........................132 calculating ........................132,134 definition [...]

Parking brake ............................ 114 Parts (see Motorcraft parts) ....212 Power distribution box (see Fuses) ........................................ 149 Power door locks ........................ 75 Power steering .......................... 115 fluid, checking and adding .... 182 fluid, refill capacity ................ 212 fluid, specific[...]

V ehicle Identification Number (VIN) .......................................... 222 V ehicle loading .......................... 132 V entilating your vehicle ........... 111 W arning chimes ........................... 13 W arning lights (see Lights) ......... 8 W asher fluid .............................. 177 W ater , Driving through ............. [...]

241[...]

242[...]

243[...]

244[...]

245[...]

246[...]

247[...]

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity Refer to Refill capacities in the Capacities and specifications chapter . Engine oil (includes filter change) 5.7L (6.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire size and pressure Refer to the Certification Label insid[...]