Ford 1999 Mustang manuale d’uso

Before driving Introduction 2 Instrumentation 4 Controls and features 16 Seating and safety restraints 64 Starting and driving Starting 87 Driving 92 Roadside emergencies 112 Servicing Maintenance and care 130 Capacities and specifications 182 Customer assistance 191 Reporting safety defects 206 Index 207 All rights reserved. Reproduction by any me[...]

ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regardi[...]

INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of Cobra vehicles Before you drive your vehicle, be sure to read the “SVT Cobra Owner’ s Guide Supplement.” This book contains im[...]

P ! BRAKE L 0 00000 0 0 C E F H LH 10 20 40 60 80 20 40 60 80 100 12 0 140 160 180 200 220 240 100 120 140 30 50 70 90 110 130 150 4 5 6 7 8 3 2 1 H THEFT REAR DEF RPMX1000 FUEL DOOR SELECT/RESET LOW FUEL O/D OFF AIR BAG SERVICE ENGINE SOON MPH km/h ABS . OFF HI LO Headlamp control (pg. 16) Driver side air bag (pg. 74) T urn signal and wiper/washer[...]

POWER AUDIO VOLUME AM/FM REW FF PLAY EJCT 1 2 3 4 5 CLOCK AUTO PRESET PROG AUTOMATIC DNR CrO 2 SCAN TUNE SEEK FM1 ST LO HI OFF FLOOR MIX VENT NORM A/C MAX A/C Climate control systems (pg. 18) Electronic sound system (pg. 21) Instrumentation 5[...]

W ARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter . [...]

High beams Illuminates when the high beam headlamps are turned on. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Charging system Illuminates when the ignition is turned to the ON position and the[...]

Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the s[...]

consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the Service Engine Soon light remains on, have your vehicle serviced at the first available opportunity . Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderat[...]

T raction Control Y active This light momentarily illuminates when the ignition is turned to ON. It also illuminates when the T raction Control y system begins applying and releasing the brakes and adjusting the engine characteristics to limit a wheelspin condition. It will be lit for a minimum of four seconds or for the duration of the T raction C[...]

and more needs to be added. This lamp will also illuminate when the ignition is turned to ON and the engine is off. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and care chapter . Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime,[...]

Optional instrument cluster gauges Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty , there is a small amount of[...]

Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Speedometer Indicates the current vehicle speed. • Base instrument cluster • Optional instrument cluste[...]

T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer at the top of the scale or in the red zone may damage the engine. • Base instrument cluster • Standard instrument cluster T rip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T?[...]

Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exi[...]

HEADLAMP CONTROL • Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. • Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps). Daytime running lamps (DRL) (if equipped) T urns the headlamps on[...]

P ANEL DIMMER CONTROL T o adjust the brightness of the instrument panel: • Rotate clockwise/ counterclockwise when the headlamp control is in the parking lamp or low-beam position. T o turn on the courtesy lamps: • Rotate fully counterclockwise. REAR WINDOW DEFROSTER (IF EQUIPPED) The rear defroster control is located on the instrument panel. P[...]

CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will[...]

Under normal conditions, your vehicle’ s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. In snowy or dirty conditions, leave the mode selector in the OFF position when the ignition is turned off. • MAX A/C-Use[...]

the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging. • -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher , the air [...]

top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette/Premium Sound Power control [...]

AM/FM select The AM/FM select control works in radio mode and allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust in radio mode T une adjust allows you to tune in a particular radio station. Y ou can manually locate the station by using the Automatic Music Search (AMS[...]

Seek function in tape mode The Automatic Music Search (AMS) feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. • Press the AMS control. • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. The tape deck stops and retur[...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Repeat the steps [...]

• Press (+) or (−) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. • Push the AUDIO control repeatedly until the display reads BAL. • Press the (+) side of the volume control to shift sound to the right speakers. • Press the[...]

Rewind/fast forward The rewind and fast forward controls work in tape mode. Rewind/fast forward function in tape mode • Press to rewind the tape. Play will continue once the beginning of the tape is reached or rewind is stopped. • Press to fast forward the tape. Once the end of the tape is reached, tape direction reverses and the opposite side [...]

AM/FM Stereo/Cassette/MACH 460 Sound System T with Premium AM/FM Stereo Cassette Power control Press the control to turn the audio system on or off. V olume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level wh[...]

Tune adjust T une adjust works in radio mode and allows you to manually tune in a particular radio station. • Press the SCAN/TUNE button twice. • The display reads TUNE. Press the SEEK control to move up or down through the frequencies. • Press to move down or to move up the frequency band. • Press and hold down or to quickly move through t[...]

• Press to listen to the next selection on the tape. Scan function The scan function works in radio, tape and CD mode (if equipped). Scan function in radio mode This feature allows you to scan the frequency band, stopping on each listenable station for approximately a five-second sampling. • Press the SCAN/TUNE button to enter the scan mode. ?[...]

• Press to scan forward selections. Press the SCAN/TUNE button again to stop the scan mode on the current selection. Radio station memory preset The radio is equipped with five station memory preset controls. These controls can be used to select up to five preset AM stations and ten FM stations (five in FM1 and five in FM2). Setting memory preset[...]

• Push the AUDIO control repeatedly until the display reads TREB. • Press (+) or (−) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. • Push the AUDIO control repeatedly until the display reads BAL. • Press the (+) side of th[...]

T ape play select Insert a cassette tape into the cassette deck. Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way . Press PLA Y to begin cassette tape play . Rewind/fast forward function in tape mode Press the control to rewind the tape. Play[...]

Setting the clock Press the CLOCK control while simultaneously depressing the SEEK control. • Press to set the hours. • Press to set the minutes. Premium AM/FM Stereo Single CD Radio/Premium Sound or MACH 460 Sound System T with Single CD Radio Power control Press the control to turn the audio system on or off. V olume control Press the control[...]

wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio mode and allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in r[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode. Scan function with compact disc radio • Press the SCAN/ TUNE control once. • Push on the SEEK control to hear a brief samplin[...]

3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. If the battery is disconnected, the memory preset stations will need to be reset. Automatic memory store (if equipped) Automatic memory store allows you to set strong radio stations without losing your original ma[...]

• Push the AUDIO control repeatedly until the display reads BAL. • Press the (+) side of the volume control to shift sound to the right speakers. • Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers. • Push the AUD[...]

• Press the control for more than three seconds for fast forward action. CD eject Press the control to stop and eject a CD. If a disc is ejected from the CD player but is not removed within approximately 10 seconds, the player will automatically reload the disc for storage (unless the disc is automatically ejected because it was inserted upside d[...]

Single Disc CD Player (if equipped) Power and volume control The compact disc player operates when the audio system is on and a CD is inserted (label side up). The volume is controlled by the VOLUME control on the audio system. Play function The system enters the PLA Y mode when a CD is loaded, label side up, into the disc opening. The PLA Y indica[...]

Scan function Press the SCAN control to enter the scan mode. The CD player will begin scanning the CD, stopping on each listenable track for approximately eight seconds. This continues until you press the SCAN control a second time or eject the CD. While in the scan mode, the display flashes SCAN. Reverse/fast forward T o quickly search for a parti[...]

Compression adjust brings soft and loud CD passages together for a more consistent listening level. Shuffle feature The shuffle feature plays all tracks on the current CD in random order . Press the SHUFFLE control to start this feature. Random order play will continue until the control is pressed again. Eject Push the EJECT control to stop CD play[...]

• The player’ s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing. If necessary , clean discs only with an approved CD cleaner and wipe from the ce[...]

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.9, 88.1–107.1, 107.9 MHz Not all frequencies are used in a given area. Radi[...]

Audio system warranties and service Refer to the “W arranty Guide” for audio system warranty information. If service is necessary , see your dealer or a qualified technician. T RUNK REMOTE CONTROL Press the remote trunk release control located in the glove compartment. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push[...]

Mist Function T o operate the Mist function of the windshield wipers, push and release the windshield washer control quickly . The wipers will cycle one or two times. HIGH BEAMS Push forward to activate. FLASH TO PASS Pull toward you to activate and release to deactivate. POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories su[...]

5. ST ART , cranks the engine. Release the key as soon as the engine starts. TIL T STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steerin[...]

T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET/SET ACC/ SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive[...]

T o set a higher set speed • Press and hold SET/ SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET/SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET[...]

T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/ RESUME. For RES/ RSM/RESUME to operate, the vehic[...]

INTERIOR LAMPS Map lamps (if equipped) If equipped with a convertible top the map lamps and controls are located on the rearview mirror . Press the controls on either side of each map lamp to activate the lamps. POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch t[...]

Express down T o make the driver window open fully without holding the window control, press the driver window control completely down and release quickly . Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s [...]

2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation [...]

Foglamp control (if equipped) T urn on the parking lamps or the low-beam headlamps. Press the top portion of the foglamp control, located on the center console, to activate the foglamps. The foglamp LED will illuminate when the foglamps are on. Press the bottom portion of the foglamp control to deactivate the foglamps. Auxiliary power point The pow[...]

2. Check the convertible top stowage compartment behind the rear seat to be sure it is empty and ready to receive the top. 3. Unclamp the top from the windshield header at both the right and left sides by pulling each clamp rearward until the hook in the windshield header is free. The clamps are flush with the header when in the closed position. 4.[...]

2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle. 4. T uck side attachments under molding. Repeat on other side of vehicle. 5. Push and pull front of boot to ensure tongue is engaged into groove. 6. Removal Controls and featu[...]

Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. T o raise the convertible top: 1. Bring the vehicle to a complete stop. Engage the parking brake. Key must be in the ON position. 2. Remove the boot cover and[...]

• confirms that the vehicle is locked with a short “beep” from the horn. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the[...]

Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view . Sounding a panic alarm Press this control to activate the alarm. T o deactivate the alarm, press the control again or turn[...]

The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the OFF position, 10 minutes after if the door is left open, and 30 minutes after if the trunk is left open or the dome lamp switch [...]

• weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle T o replace the batteries: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new batteries down. Re[...]

The SecuriLock y passive anti-theft system is not compatible with aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Large metallic objects or devices such as the Mobil Speedpass y on the same key ring as your SecuriLock y key may cause vehicle starting problems. These o[...]

Programming spare SecuriLock Y keys Spare SecuriLock y keys can be purchased from your dealership and programmed to your SecuriLock y passive anti-theft system (up to a total of 8 keys). Y our dealership can program your new SecuriLock y key(s) to your vehicle or you can do it yourself using the following simple procedure. T o program a new SecuriL[...]

4. T urn the ignition to OFF and remove the second SecuriLock y key from the ignition. 5. W ithin 10 seconds of turning the ignition to OFF , insert the unprogrammed SecuriLock y key (new key/valet key) into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). This step will program your new SecuriL[...]

SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind y[...]

Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright an[...]

Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firm[...]

Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the driver’ s seatback. Move the control up to increase firmness and down to decrease firmness. Rear seat entry/exit Use the seatback release to fold the back of the front seat forward for rear seat passenger entry or exit. This release handle is lo[...]

2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. T o lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down. When raising the seatback(s), make sure you hear the seat latch into place. SAFETY RESTRAINTS Safety restraints [...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicl[...]

The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Refer to Safety Restraints for Children or Safety Seats for Children later in t[...]

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensiti[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the w[...]

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Maintenance and care section. AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) preca[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at[...]

Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer . Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that chil[...]

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the[...]

considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the a[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident stat[...]

seats raise the child and provide a shorter , firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster should be used if the shoulder belt rests in front of the child’ s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are to[...]

When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fast[...]

Installing child safety seats in combination lap and shoulder belt seating positions If you must use a forward facing child seat in the front seat (reminder children 12 years old and unders should always be properly restrained in the rear seat). The shoulder belt must be routed through the belt holder at the top of the seatback, refer to Safety Res[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in pla[...]

Lincoln-Mercury dealer . All vehicles built for sale in Canada include a tether anchor hardware kit. Be sure to follow the child safety seat manufacturer’ s instructions. T ighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision. Seating and s[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accele[...]

Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. Do not allow the vehicle to idle for more than ten minutes at high engine RPM. Before st[...]

3. T urn the key to 4 (ON) without turning the key to 5 (ST ART). Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. 1 2 3 4 5 P ! BRAKE L 0 00000 0 0 C E F H LH 10 20 30 20 40 60 80 100 120 140 160 180 40 50[...]

ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait ten seconds and try again. 3. If the tempe[...]

Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes. These fumes are harmful a[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

The ABS operates by detecting the onset of wheel lockup during brake applications and compensating for this tendency . The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking wi[...]

stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. • W e recommend that you familiarize yourself with this braking technique. However , avoid taking any unnecessary risks. Hydraulic brake booster system (Hydroboost) The Hydroboost system receives fluid pressure from the power steering pump to[...]

(when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking[...]

controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a s[...]

T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level. If the power steering system breaks down (or if the engine is turned off), you can steer the vehi[...]

Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle for more than a few minutes. The transmission and[...]

P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift is securely latched in P (Park). Never leave your vehicle unattended while it i[...]

N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . (Overdrive) can be deactivated by pressing the transmission control switch on the end of[...]

instrument cluster . T ransmission operates in gears one through three. (Drive) provides more engine braking than (Overdrive) and is useful when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired. If towing a trailer , refer to Driving while you tow in the T railer T owing chapter . T[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch V ehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1. Put gearshift in N (Neutral). 2. Hold down brake pedal. 3. Depress clutch p[...]

Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph). This will damage the clutch. Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 18 km/h (11 mph) 2 - 3 31 km/h (19 mph) 3 - 4 48 km/h (30 mph) 4 - 5 64 km/h (40 mp[...]

4. T urn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully . Reverse Y ou can shift into R (Reverse) only by moving the gearshift to the right of 5 (Fifth) gear before you shift into R (Reverse). This is a feature that protects y[...]

gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 2 through 4. Removing key from ignition • T urn the ignition key to position 3 (OFF). • Push the release lever forward and rotate the key towards you and remove. T RACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, parti[...]

V EHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb W eight : W eight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload : Combined maximum allowable weight of cargo, passengers and optional equipment. The [...]

• Maximum T railer W eight : maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow . It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • T railer W eight Range : Specified weight range that the trailer must fall within that ranges f[...]

Always ensure that the weight of passengers, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross V ehicle W eight and Front and Rear Gross Axle W eight Rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitat[...]

If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper . Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulatio[...]

Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. T railer towing tips • Practice turning, stopping and backing u[...]

DRIVING THROUGH WATER Do not drive quickly through standing water , especially if the depth is unknown. T raction or brake capability may be limited and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, [...]

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously . • Depress control again to [...]

Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the OFF posi[...]

Standard fuse amperage rating and color COLOR Fuse Rat- ing Mini Fuses Stan- dard Fuses Maxi Fuses Car - tridge Maxi Fuses Fuse Link Car - tridge 2A Grey Grey — — — 3A V iolet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow [...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 20A Cigar Lighter 2 20A Engine Controls 3 — Not Used 4 10A RH Low Beam Headlamp 5 15A Instrument Cluster , T raction Control Switch 6 20A Starter Motor Relay 7 15A GEM, Interior Lamps 8 20A Engine C ontrols 9 — Not Used 10 10A LH Low Beam Headlamp 11 15A Back-Up L[...]

Fuse/Relay Location Fuse Amp Rating Description 16 — Not Used 17 15A Speed Control Servo, Shift Lock Actuator 18 15A Electronic Flasher 19 15A Power Mirror Switch, GEM, Anti-Theft Relay , Power Door Locks, Door Ajar Switches 20 15A Convertible T op Switch 21 5A Instrument Cluster and Engine Control Memory 22 — Not Used 23 15A A/C Clutch, Defogg[...]

Fuse/Relay Location Fuse Amp Rating Description 34 20A Instrument Cluster , CCRM, Data Link Connector , Securilock T ransceiver Module 35 15A Shift Lock Actuator , PCM, Speed Control Servo, ABS Module 36 15A Airbag Control Module 37 10A Adjustable Illumination 38 20A Highbeams 39 5A GEM 40 — Not Used 41 15A Brake Lamp 42 — Not Used 43 20A CB Po[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description Relay 1 — Fog Lamp Interrupt Relay 2 — Int. W iper Relay 3 — W iper HI/LO Relay 4 — Starter Relay 5 — Fog Lamps 1 50A** (4.6L), 30A CB (3.8L) Electric Cooling Fan Motor 2 30A** Headlamps 3 40A** Starter Motor Relay , Ignition Switch 4 40A** Igniti[...]

Fuse/Relay Location Fuse Amp Rating Description 9 20A** Auxiliary Power Point 10 30A** Parklamps 11 30A** Rear W indow Defrost Control 12 40A** Power W indows, Power Locks 13 — Not Used 14 20A* Fuel Pump 15 10A* Radio 16 20A* Horn 17 20A* Anti-Lock Brake System 18 25A* Power Seats 19 — Not Used 20 20A* Generator 21 — Not Used 22 — Not Used [...]

T emporary spare tire information Y our vehicle may have a temporary spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only . Replace this tire with a full-size tire as soon as possible. If you use the temporary spare tire continuously or do not follow these[...]

1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park) or R (manual transmission), turn engine OFF , and block the diagonally opposite wheel. 3. Remove the spare tire, jack and lug wrench. 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is r[...]

Never use the rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the s[...]

Anti-theft lug nuts (if equipped) If your vehicle is equipped with this feature, one of the lug nuts on each wheel must be removed and replaced with a special key . The key and registration card are attached to the lug wrench and stored with the spare tire. If you lose the key , send the registration card to the manufacturer (not the dealer) to get[...]

Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability . Preparing your vehicle 1. Use only a 12–volt supply to start your vehicle. 2. Do n[...]

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye. Do not use fuel lines, engine rock[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . +[...]

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. Wrecker towing If you need to have your vehicle towed, contact a professional towing [...]

It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using wheel lift equipment, the front wheels must be placed on a dolly to prevent damage to the front fascia (bumper). If the[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. T urn off the engine and remove the key . 4. Block the wheels to prevent the vehicle from moving unexpectedly . Working w[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod. HOOD Maintenance and care 132[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. W indshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10. Automatic transmission fluid dipstick (if equ[...]

4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. W indshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9. Air filter assembly 10. Automatic transmission fluid dipstick (if equipped) ENGINE OIL Checking the engine oil Refer [...]

2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dip[...]

• If the oil level is below the MIN mark, add enough oil to raise the level within the MIN—MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions[...]

Engine oil and filter recommendations Look for this Certification T rademark. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API Certification T rademark will meet all requirements for your vehicle’ s engine. Ford oil specification is WSS-M2C153-G. Do not use supplementa[...]

• 3.8L OHV V6 engine • 4.6L SOHC V8 engine 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer [...]

Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry . This may cause the brakes to fail. CLUTCH ADJUSTMENT (IF EQUIPPED) Check the clutch adjustment. Refer to the Scheduled Maintenance Guide for the service interval schedules. The [...]

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way . Do not put engine coolant in the container for the windshield washer flu[...]

ENGINE COOLANT • 3.8L OHV V6 engine • 4.6L V8 engine Check the level of the engine coolant in the reservoir . Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter . If the engine coolant has not been checked at the recommended interval, th[...]

Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549–AA (in Oregon, F5FZ-19549–CC, in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44–A. • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544–AA (orange in color). • DO NOT USE a DEX-COOL t engine coolant or an equivalen[...]

Plain water may be added in an emergency , but you must replace it with a 50/50 mixture of coolant and distilled water as soon as possible. Check the coolant level in the coolant reservoir the next few times you drive the vehicle. If necessary , add enough of a 50/50 mixture of coolant and distilled water to bring the liquid level to the fill line [...]

Always dispose of used automotive fluids in a responsible manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter . Have your d[...]

If your vehicle is equipped with the 3.8L V6 engine, check the power steering fluid level with the engine at normal operating temperature. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine i[...]

If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at ambient temperature. Allow at least one-half hour after driving for the power steering fluid to cool. 1. Start the engine and allow the engine to idle. 2. T urn the steering wheel left and right several times. 3. T urn the engine off. 4. Check[...]

been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the par[...]

could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in tr[...]

An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fl[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte l[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

4. The relearning process will automatically complete as you drive the vehicle. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearne[...]

Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wi[...]

about tire grades exactly as the government has written it. T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade[...]

Motor V ehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law . The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combi[...]

• 15 or 16 inch four tire rotation • 17 inch four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. Maintenance and care 156[...]

When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity . Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may[...]

The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. Use chains on the tires only in an emergency or if the law requires them. Follow these guidelines when using snow tires and chains: • Chains may damage aluminum wheels. • Use only Cable [...]

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel sys[...]

• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothi[...]

• Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position. Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap count[...]

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury . Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. D[...]

“Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel. Cle[...]

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Y our best source of information about actual fuel economy is you, the driver . Y ou must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy . W e do not recommend taking fuel econo[...]

• Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Y our results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the [...]

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for [...]

• Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow the rec[...]

EP A window sticker Every new vehicle should have the EP A window sticker . Contact your dealer if the window sticker is not supplied with your vehicle. The EP A window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker . These numbers rep[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the charging system warning light, “Service Engine Soon” light or the temperature warning light, fluid leaks, strange odors, smoke or loss of oil pressu[...]

If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. T o ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving o[...]

Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then [...]

T o install the new bulb: 1. W ith the flat side of the new bulb’ s plastic base facing upward, insert the glass end of the bulb into the lamp assembly . Y ou may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly . When the grooves are aligned, push the bulb into the lamp assembly unti[...]

5. Rotate the bulb socket counterclockwise about 1 ⁄ 4 turn and remove from lamp assembly . 6. Carefully pull the bulb straight out from the socket and push in the new bulb. 7. T o complete installation, follow the removal procedure in reverse order . High-mount brakelamp bulbs 1. Open trunk. 2. Inside trunk, locate access hole under the rear dec[...]

1. Rotate the foglamp bulb counterclockwise and remove from foglamp (the rear side of the foglamp is shown). 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the foglamp bulb in foglamp by rotating clockwise. Replacing license plate lamp bulbs T o change the licens[...]

Map lamps For bulb replacement, see a qualified service technician or your dealer . Using the right bulbs Function T rade Number T ail lamp, brakelamp, turn lamp 3157K Park lamp, turn lamp, side marker (front) 3157NAK Backup lamp 3156K License plate lamp 168 High-mount brakelamp 906 Headlamps 9007 Luggage compartment lamp 906 Dome lamp 575 Map lamp[...]

V ertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. 2. Measure the height from the center of your headlamp to the ground and mark an 2.4 meters (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking ta[...]

W ashing your vehicle W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. T o avoid spots, avoid washing when the hood is still warm, i[...]

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra T ouch Prep and Finishing Kit (#F7AZ-19K507–BA), touch-up paint (#ALBZ-19500–XXXXA), or aerosol paint spray (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your[...]

• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, sol[...]

If the wiper still does not wipe properly , this could be caused by substances on the windshield such as tree sap and some hot wax treatments used by commercial car washes. Clean the outside of the windshield with a non-abrasive cleanser such as the non-abrasive Bon-Ami t powder . Rinse thoroughly with clean water . Do not use abrasive cleansers on[...]

Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl or plastics. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check t[...]

MOTORCRAFT PART NUMBERS Component 3.8L OHV V6 engine 4.6L SOHC V8 engine Air filter element F A-1611 F A-1634 Fuel filter FG-800A FG-800A Battery BXT -59 BXT -59 Oil filter FL-400S FL-820S PCV valve EV -152 EV -98 Spark plugs* A WSF-42EE** A WSF-32PP*** * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information. *[...]

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High Per - formance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine oil (includes filter change) Motorcraft 5W -30 Super Premium Motor Oil All 4.7L (5.0 quarts) Engine coolant 1 Premium Engine Coolant 3.8L OHV V6 engine 11.2L (11.8 quarts) 4.6L SOHC V8 eng[...]

Fluid Ford Part Name Application Capacity T rans- mission fluid Motorcraft MERCON t V AT F 3 Automatic with 3.8L OHV V6 engine 13.1L (13.9 quarts) Automatic with 4.6L SOHC V8 engine 12.0L (12.8 quarts) Motorcraft MERCON t AT F Manual with 3.8L OHV V6 engine 2.6L (5.6 pints) Manual with 4.6L SOHC V8 engine 4 3.1L (6.6 pints) W indshield washer fluid[...]

3 Ensure the correct automatic transmission fluid is used. T ransmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCON t and MERCON t V are not interchangeable. DO NOT mix MERCON t and MERCON t V . Refer to your Scheduled Maintenance Guide to determine the correct service interval. 4 Service refill capacity is d[...]

Item Ford part name Ford part number Ford speci- fication Engine coolant Ford Premium Engine Coolant E2FZ- 19549-AA (in Oregon, F5FZ- 19549-CC, in Canada, Motorcraft CXC-10) ESE- M97B44-A Engine oil Motorcraft 5W -30 Super Premium Motor Oil XO- 5W30-QSP WSS- M2C153-G with API Certification Mark Lock cylinders Penetrating and Lock Lubricant E8AZ- 19[...]

Item Ford part name Ford part number Ford speci- fication Manual transmission fluid Motorcraft MERCON t AT F XT -2-QDX MERCON t Disc brake caliper rails Silicone Brake Caliper and Dielectric compound D7AZ- 19A331-A (Motorcraft W A-10) ESE- M1C171-A W indshield washer fluid Ultra-Clear W indshield W asher Concentrate C9AZ- 19550-AC ESR- M17P5-A 1 Ad[...]

ENGINE DATA Engine 3.8L OHV V6 engine 4.6L SOHC V8 engine Cubic inches 232 281 Horsepower 190 @ 5250 rpm 260 @ 5250 rpm T orque 220 lb.-ft. @ 2750 rpm 302 lb.-ft. @ 4000 rpm Required fuel 87 octane 87 octane Firing order 1-4-2-5-3-6 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052- 00.056 inch) 1.3-1.4 mm (0.052- 00.056 inch) Ignition system EDIS C[...]

2 5 3 4 1 Capacities and specifications 189[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. V ehicle identification number [...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

T o receive roadside assistance in the United States for Ford or Mercury vehicles, call 1-800-241-3673 or if you own a Lincoln vehicle, call 1–800–521–4140. In Canada call 1–800–665–2006. Should you need to arrange assistance for yourself, Ford will reimburse a reasonable amount. T o obtain information about reimbursement, call 1-800-24[...]

you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options. Also, please be aware that some dealers offer service contracts that are not backed by Ford Motor Company or Ford of Canada. On the[...]

general manager of the dealership. In most cases, your concern will be resolved at this level. Ford Motor Company and Ford of Canada dealerships also carry genuine Ford parts and accessories, providing you with original equipment reliability . Away from home If you are away from home when your vehicle needs service, or if you need more help than th[...]

If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.) or the Mediation/Arbitration Program (Canada). In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by stat[...]

• sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’ s performance as designed • a request for reimbursement of consequential expenses unless a service or product concern being reviewed • items not covered by the New V ehicle Limited W arranty (including maintenance and wea[...]

What the Board needs T o have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form. Y our application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: • the file number assigned to your application • the toll-free p[...]

Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. Oral presentation may be requested by the Board as well. Ma[...]

Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and wher[...]

If you are in another foreign country , contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Moto[...]

complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’ s rigid engineering and safety specifications. Ford accessories are warranted for up to 12 months or 20,000 km (12,000 miles) on all cars and light trucks and 12 months with unlimited distance[...]

T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running [...]

Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates T ailgate covers T ailgate [...]

• The Federal Communications Commission (FCC) and Canadian Radio T elecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and shou[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST , for credit card holders only T o order the publicat[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Air bag supplemental restraint system ........ 74 and child safety seats ............. 76 description .............. 74 disposal .................... 79 driver air bag .......... 77 indicator light ...... 7,78 operation ................. 77 passenger air bag ... 77 Air cleaner filter ..... 182 Air conditioning ........ 18 manual heating and air con[...]

safety belts ............ 181 washing .................. 177 waxing ................... 177 wheels .................... 178 windows ................ 181 wiper blades .......... 179 Clock ..................... 33,38 Clutch adjusting ................ 139 operation while driving ......... 102 recommended shift speeds ........... 103 Console ..........[...]

Fluid capacities ....... 183 Foglamps ................... 53 Fuel .......................... 158 calculating fuel economy ................ 164 cap ......................... 161 capacity ................. 183 choosing the right fuel ......... 162 comparisons with EP A fuel economy estimates ............... 168 detergent in fuel ... 163 filling your [...]

Infant seats (see Safety seats) ..... 81 Inspection/maintenance (I/M) testing ............ 169 Instrument panel ........ 6 cleaning ................. 180 lighting up panel and interior ............. 17 location of components ............... 6 Jump-starting your vehicle ...................... 123 Keys key in ignition chime ....................... 11[...]

Power distribution box (see Fuses) ............. 117 Power door locks ...... 51 Power steering .......... 96 fluid, checking and adding ............ 144 fluid, refill capacity ................. 183 fluid, specifications . 185,188 Radio .......................... 21 Relays ...................... 113 Remote entry system ................... 56,58 illu[...]

T raction control ........ 95 active light .............. 10 T raction-lok rear axle .................. 105 T ransmission automatic operation ................. 97 fluid, checking and adding (automatic) ........... 146 fluid, checking and adding (manual) ... 149 fluid, refill capacities ...... 183 lubricant specifications ........ 188 manual operati[...]

213[...]

214[...]

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 58.7L (15.5 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G T ire size and pressure Refer to the Certification Label. Hood release Pull handle under the left side of t[...]

1 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter . 2 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 3 Ensure the correct autom[...]