Ford 2010 Transit Connect manuale d’uso

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Entertainment Systems 20 AM/FM stereo 20 AM/FM stereo with CD 21 Auxiliary input jack (Line in) 23 Bluetooth system 25 Climate Controls 35 Manual heating and air conditioning 35 Rear window defroster 37 Lights 38 Headlamps 38 T urn signal control 41 Bulb replacement 42 Dri[...]

Seating and Safety Restraints 70 Seating 70 Safety restraints 80 Airbags 92 Child restraints 104 Tires, Wheels and Loading 122 T ire information 124 T ire inflation 126 T ire Pressure Monitoring System (TPMS) 138 V ehicle loading 146 T railer towing 151 Recreational towing 152 Driving 153 Starting 153 Brakes 157 AdvanceT rac 威 160 T ransmission o[...]

Maintenance and Specifications 21 1 Engine compartment 213 Engine oil 215 Battery 218 Engine coolant 220 Fuel information 226 Air filter(s) 240 Part numbers 241 Maintenance product specifications and capacities 242 Engine data 245 Accessories 249 Ford Extended Service Plan 251 Index 254 All rights reserved. Reproduction by any means, electronic or [...]

CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following [...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’[...]

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly d[...]

may seek to access the information independently of Ford Motor Company and Ford of Canada. T o the extent that any law pertaining to Event Data Recording applies to SYNC 威 or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911 Assist may , through any paired and connected cell phone, disclose to emergen[...]

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turn[...]

Safety belt: Reminds you to fasten your front driver and passenger safety belt. A Belt-Minder 威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature. Charging system: Illuminates when the battery is not charging properly . If it [...]

Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating your tires in the T ires, Wheels and Loading chapter . When the ignition is first turned to on, the light will illuminate for three seconds to ensure the bulb is workin[...]

Headlamps: Illuminates when the low–beam headlamps are turned on. Rear fog lamps: Illuminates when the rear fog lamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’ s door is opened. Park warning chime: Sounds when the transmission is not in Park, the dr[...]

GAUGES Speedometer: Indicates the current vehicle speed. T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Instrument Cluster 17 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range. If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. If it enters the red section and the service engine soon[...]

Information display 1. Distance to empty / clock: Registers the approximate distance the vehicle can travel before refuelling is necessary . Clock shows the current set time. Switching the display between “clock” and “distance to empty”: • V ehicles with “clock” displayed normally: Press the Select button (4) to switch to the “dista[...]

AUDIO SYSTEMS AM/FM stereo (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell [...]

Sound Adjustments Press MENU repeatedly to cycle through the following features: BASS: Press to adjust the level of bass. TREBLE: Press to adjust the level of treble. BALANCE: Press to adjust the audio between the left (L) and right (R) speakers. F ADE: Press to adjust the audio between the back (B) and front (F) speakers. AM/FM stereo with single [...]

Setting the clock T o set the time or date, turn the radio on and press CLOCK until the time begins to flash. Press or to access the desired selection (date or time). Once the desired selection is flashing, turn the VOL (V olume) control to adjust the time or date forward/backward. Press CLOCK again. AM/FM radio AM/FM: Press repeatedly to select AM[...]

MENU: Press repeatedly to access the following features: MAN: Press < or > to manually advance down or up the chosen frequency band. SCAN: Press < or > for a brief sampling of radio stations or CD tracks. SHUFFLE CD: Select to shuffle the tracks on the current CD. REPEA T CD: Select to repeat the current CD. COMP (Compression): Select t[...]

The auxiliary input jack allows you to connect your portable music player and play music through the vehicle speakers with high fidelity . Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm) connectors at each end. T o play your portable music player usin[...]

portable music players have different output levels, so not all players should be set at the same levels. Some players will sound best at full volume and others will need to be set at a lower volume. 3. If the music sounds distorted at lower listening levels, turn the portable music player volume down. If the problems persists, replace or recharge [...]

Getting started Pairing (bonding) your phone The first thing you must do to use the system is to pair (bond) your Bluetooth enabled cellular phone with your vehicle’ s Bluetooth system. This process allows your phone to communicate with the hands-free system and ensures that other phones cannot inadvertently do so. Y ou may pair/bond up to six ph[...]

V oice recognition Y our Bluetooth system is equipped with a voice recognition system which allows you to perform some operations by speaking certain commands to the system. The system will respond with a series of beeps, confirmations or questions when necessary . At any time, you can say , “Cancel” if you do not wish to continue, or “Help?[...]

Microphone Y our vehicle has a microphone located in the A-pillar for the hands-free phone features and voice commands. T o mute the microphone: During an active call, press < or > on the audio system. Press again to un-mute and return to normal function. V oice commands V oice commands allow you to speak commands to the system while enabling[...]

CD player voice commands Press the VOICE button on the stalk. After the tone, say , “CD player” and then any of the following commands: • Play • T rack 1 • Shuffle all • Shuffle folder 2 • Shuffle off • Repeat folder 2 • Repeat track • Repeat off • Help 1 Can be used as a shortcut. 2 Only available as a voice command if the CD[...]

Phone voice commands Press the VOICE button on the stalk. After the tone, say , “Phone” and then any of the following commands: • Mobile name 1 • Dial name 1 • Dial number 1 • Delete name • Delete directory • Play directory • Store name* • Redial 1 • Accept calls • Reject calls • Help 1 Can be used as a shortcut. Store nam[...]

Making a call using voice commands T o make a hands-free call using your system: 1. Press the VOICE button on the stalk. 2. When the tone sounds, say , “Phone”. The system will confirm you are in phone mode. 3. Say , “Dial name” or “Dial number”. 4. When prompted, say the desired name or phone number . The system will ask you to confirm[...]

T o accept the incoming call, press the button on the audio system. T o reject the incoming call, by pressing CD or AM/FM on the audio system. Redialing a number T o redial a number: 1. Press on the audio system to enter the phone menu. 2. Press MENU repeatedly to cycle through CALL OUT , CALL IN, MISSED, INCOMING or OUTGOING appears in the display[...]

3. Press < or > on the audio system to scroll through the list of paired (bonded) phones. 4. When the desired selection appears in the display that you would like to delete, press MENU. GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T[...]

• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. T emperature control: Controls the temperature of the airflow in the vehicle. For optimum defrosting performance, set the dial to the defrost symbol . 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control setting: : Distri[...]

4. Recirculated air: Press to activate/deactivate air recirculation in the vehicle cabin. Recirculated air may reduce the amount of time required to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculated air will not function in (defrost). 5. A/C: Press to activate/deac[...]

T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middl[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Rear fog lamp The headlamp control also operates the rear fog lamp. The rear fog lamp can only be turned on when the headlamp control is in the position. Pull the headlamp control towards you to tu[...]

High beams Pull the lever toward you to the second detent to activate the high beams. Pull the lever again toward you to the second detent to deactivate. Flash to pass Pull the lever toward you to the first detent to activate flash to pass, and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all[...]

V ERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and m[...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome lamps The dome lamp is equipped with a control switch that will illuminate when: • the doors are closed and the switch is in the right position. • the switch is in the middle position and any door is open. When [...]

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin [...]

Replacing interior bulbs Check the operation of all bulbs frequently . Replacing front dome lamps 1. Make sure the headlamp switch is in the off position. 2. Switch off the interior lamps. 3. Pry out the light assembly with a flat screwdriver . Install in reverse order . Replacing rear dome lamps 1. Make sure the headlamp switch is in the off posit[...]

Replacing reading bulbs 1. Open the reading lamp assembly . 2. Pull the bulb straight out and replace it. 3. After the bulb has been replaced, close the lamp assembly . Install in reverse order . Replacing exterior bulbs Check the operation of all bulbs frequently . Replacing headlamp bulbs 1. Make sure the headlamp control is in the off position a[...]

Replacing front parking lamp bulbs 1. Make sure the headlamp control is in the off position. 2. T urn the cover counterclockwise and remove it. 3. Remove the bulb and the bulb socket. 4. Pull the bulb straight out. Install in reverse order . Lights 45 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Replacing front turn signal bulbs 1. Make sure the headlamp control is in the off position and open the hood. 2. Remove the bulb socket from the lamp assembly by turning it counterclockwise. 3. Pull the bulb straight out of the socket. Install in reverse order . Replacing tail/brake/backup lamps and turn signal bulbs 1. Make sure the headlamp contr[...]

3. Remove the bulb socket from the lamp assembly by turning it counterclockwise. 4. Pull the bulb straight out of the socket. Install in reverse order . Lights 47 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Replacing front and rear side marker bulbs 1. Make sure the headlamp control is in the off position and then open the cargo door . 2. Remove the side marker by gently prying the lamp assembly away from the vehicle. 3. Remove the bulb socket from the lamp assembly by turning it counterclockwise. 4. Pull the bulb straight out of the socket. Install i[...]

Replacing high-mount brake lamp bulbs See your authorized dealer for replacement. Replacing license plate lamp bulbs 1. Make sure the headlamp control is in the off position. 2. Remove the lens assembly . 3. Pull the bulb straight out. Install in reverse order . Lights 49 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

MUL TI-FUNCTION LEVER W indshield wiper Move the lever down for a single wipe. For intermittent operation, move control up one position and adjust the rotary control to the desired speed. For normal operation, move control up two positions and up three positions for high speed wiping. W indshield washer T o activate the windshield washer , push the[...]

TILT AND TELESCOPE STEERING COLUMN Release the locking lever to adjust the height of the steering wheel and its distance from the driver . Return the lever to its original position to secure the wheel. W ARNING: Never adjust the steering wheel when the vehicle is moving. CENTER CONSOLE Y our vehicle has a variety of console features. These include:[...]

OVERHEAD STORAGE SHELF The storage shelf above the windshield can be used for storing light objects such as safety jackets, coats, etc. W ARNING: Do not place heavy or hard objects in the overhead storage, which may fall while driving, and could cause serious injury . AUXILIARY POWER POINTS (12VDC) Power outlets are designed for accessory plugs onl[...]

T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is not running, • do not leave battery chargers, video game adapters, computers and other devic[...]

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror: up, down and from side-to-side. Push the tab to help reduce glare at night. W ARNING: Do not adjust the mirror while the vehicle is in motion. EXTERIOR MIRRORS Power side view mirrors (if equipped) T o adjust your mirrors: 1. Rota[...]

SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal. W ARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speed control are located on the steering wheel. 1. Press O[...]

Resuming a set speed Press RES and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold SET + until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up [...]

• Depress the brake pedal until the desired vehicle speed is reached, press SET +. Turning of f speed control Press OFF . Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) The following functions can be operated with the steering wheel controls: V olume [...]

Seek Move the SEEK switch up or down: • In radio mode, this will locate the next radio station up or down the frequency band. • In CD mode, it will select the next or previous track. Mode Briefly press the button on the side: • In radio mode, this will locate the next pre-set radio station. • In CD mode, this will select the next CD when eq[...]

DUAL REAR DOORS Open the right hand door first from either the outside (1) or inside (2) the vehicle. Open the left hand door second by squeezing the handle to unlatch the door and pulling it open. 12 Driver Controls 59 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Note: The dual rear doors should be closed before driving your vehicle. Leaving the doors open could cause serious damage to them and their components. The left door must be closed first. Opening the doors fully Push the yellow button located on the door and swing it open. The check arms will automatically re-engage when the doors are closed. Drive[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock™ Passive Anti-theft system, your keys are electronically coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you[...]

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Remo[...]

T wo-step door unlocking • Press and release to unlock the passenger doors. • W ithin three seconds, press and release again to unlock all the doors. Note: The interior lamps will illuminate if the control on the overhead lamp is not set to the off position. One-step door unlocking If the one step door unlocking feature is activated, press and [...]

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. Carefully separate the transmitter unit from the key using a flat object (e.g. a screwdriver) at the recess on the back. 2. Open the transmitter unit by separating the retaining clips on the sides with t[...]

7. Snap the two halves back together . Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lo[...]

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the on position, or • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if[...]

Anti-theft indicator The anti-theft indicator is located in the instrument cluster . • When the ignition is in the off position, the indicator will flash briefly to indicate the SecuriLock™ system is functioning as a theft deterrent. The indicator light will stop flashing after approximately 10 seconds. • When the ignition is in the on positi[...]

The process for programming Securilock™ keys is independent of the process for programming Remote Entry T ransmitters. If your vehicle is fitted with Securilock™ and Remote Entry , you must perform both learning procedures in order to program both the Immobilizer and Remote Locking functions of the key fob. T ips: • A maximum of eight keys ca[...]

11. Y our new , unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’ s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’ s engine and the theft indicator light will flash on and [...]

SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W ARNING: Before returning the seatback to its original position[...]

T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve lock/release button and pushing down on the head restraint. Properly adjust the head restraint so that th[...]

T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Use a push tool, such as a key , to press the small button located on the side of the guide sleeve and, at the same time, press the lock/release button, then pull the head restraint upward. T o reinstall the[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front manual seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle[...]

Move the front control to raise or lower the seat cushion. Using the manual lumbar support The lumbar support control is located on the in-board side of the seatback. T urn the lumbar support control clockwise for more support. T urn the lumbar support counter -clockwise for less support. Using the armrest (if equipped) Move the armrest up or down.[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion. The adjustable head restraints consist of : • a trimme[...]

Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position. W ARNING: The adjustable head restraint is a safety device. Whenever possible it should b[...]

T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants o[...]

T o lower both seatbacks: 1. Remove all head restraints. Refer to Adjustable rear head restraints in this chapter . Note: Place the head restraint underneath the back of the front seat for storage. 2. Pull the levers on the side of the seatback. 3. Fold the seatback forward. T o place the seat in the tumble position: 4. Pull the release straps up. [...]

Returning the seat to the upright position W ARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of [...]

• Unlocked SAFETY RESTRAINTS Personal Safety System 姞 The Personal Safety System 威 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating t[...]

Module (RCM). During a crash, the RCM may activate the safety belt pretensioners and/or either none, one, or both stages of the dual-stage airbag supplemental restraints based on crash severity and conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wro[...]

are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front. W ARNING: Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat,[...]

Front outboard safety belt energy management retractors The front safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum. This helps reduce the risk of force-related injuries to the occupant’ s chest by limiting the load on the o[...]

W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided. W ARNING: I[...]

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. T o unfasten, push the release button and remove the tongue from the buckle.[...]

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat, except a booster , is installed[...]

W ARNING: After any vehicle collision, the safety belt systems at all seating positions (except the driver position, which does not have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly . In addition, all safety belts should be checked for prop[...]

W ARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision. Safety belt warning light and indicator chime The safety belt warning light illuminates in the in[...]

Both the driver’ s and passenger’ s safety belt usages are monitored and either may activate the Belt-Minder 威 feature. The warnings are the same for the driver and the front passenger . If the Belt-Minder 威 warnings have expired (warnings for approximately five minutes) for one occupant (driver or front passenger), the other occupant can s[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during our[...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

1. T urn the ignition switch to the on position. DO NOT ST ART THE ENGINE. 2. W ait until the safety belt warning light turns off (Approximately 1–2 minutes). • Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. Buckle then unbuckle the driver’ s safety belt nine times at a moderate speed, ending in t[...]

W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. W ARNING: Always transport children 12 years old and under in a rear seating position, and always properly use appropriate child restraints. Never place a rear -facing c[...]

W ARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury . Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and airbags Children must always be properly restrained. Accident statistics suggest that children are saf[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serio[...]

Front passenger sensing system The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor V ehicle Safety Standard (FMVSS) 208 and is designed to disable (will not inflate) the front passenger’ s frontal airbag under certain conditions. The front passenger sensing system works with sensors that are part of[...]

When the front passenger seat is not occupied (empty seat) or in the event that the front passenger frontal airbag is enabled (may inflate), the indicator lamp will be unlit. The front passenger sensing system is designed to disable (will not inflate) the front passenger’ s frontal airbag when a rear facing infant seat, a forward-facing child res[...]

Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small child in child safety seat or booster Lit Disabled Small child with safety belt buckled or unbuckled Lit Disabled Adult Unlit Enabled W ARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position[...]

Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. three-ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty seat, or small to medium object with safety belt buckled Lit Disabled If you think that the status of the passenger airbag off indicator lamp is inc[...]

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If ob[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any[...]

How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side air[...]

W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase t[...]

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device [...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Small children Children who have outgrown or no[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lower anchors and top tether anchor) Safety belt only Rear facing [...]

W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age. Follow the child restraint manufacturer’ s instructions and warnings provided for installation and use in conjunction with the ins[...]

training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle. T o locate a child seat fitting station[...]

Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat. Installing child safety seats with combination lap and shoulder belts Check to make sure the child seat is prope[...]

1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure th[...]

4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull[...]

snugness of the child seat to the vehicle. Sometimes, a slight lean towards the buckle will additionally help to remove remaining slack from the belt. 9. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter . 10. Before placing the child in the seat, forcibly move th[...]

Y our vehicle has LA TCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seat back. Follow the child seat manufacturer’ s instructions to properly install a ch[...]

Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor , if applicable. T ug the child seat from side to side and forward and back where it is secured to the vehicle. The seat should move less than one inch when you do this for a proper installation. If the safety seat is not anchored prop[...]

• Five-passenger vehicle Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat has been installed, using either the safety belt or the lower anchors of the LA TCH system, you can attach the top tether st[...]

2. Locate the anchor for the center seating position. 3. Clip the tether strap to the anchor as shown. Second-row outboard seating positions 1. Remove the head restraint. For instructions on how to remove the head restraint, refer to Second row adjustable head restraints earlier in this chapter . Note: Place the head restraint underneath the back o[...]

• On four -passenger vehicles the anchor is located on the driver -side upper rear door frame area close to the roof. 3. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 4. T ighten the child safety seat tether strap according[...]

Although the lap/shoulder belt will provide some protection, children who have outgrown a typical child seat are still too small for lap/shoulder belts to fit properly , and wearing an improperly fitted vehicle safety belt could increase the risk of serious injury in a crash. T o improve the fit of both the lap and shoulder belt on children who hav[...]

T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head [...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

VEHICLE CHARACTERISTICS How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. • Shorter – to give i[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are determined by standards th[...]

W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to [...]

Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an [...]

W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It al[...]

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve [...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi grea[...]

W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Highway hazards No mat[...]

• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equip[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA)[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system [...]

W ARNING: The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter . Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle r[...]

When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air . It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System:[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. TPMS reset procedure The TPMS reset procedure needs to be performed after each tire rotation. W ARNING: T o determine the required pressure for your vehicle – refer to the Safety Co[...]

2. Place the ignition in the off position and keep the key in the ignition. 3. Cycle the ignition to the on position with the engine off. 4. T urn the hazard flashers on then off 3 times. This must be accomplished within ten seconds. If the reset mode has been entered successfully , the horn will sound once and the TPMS indicator will flash. If thi[...]

8. Remove the valve cap from the valve stem on the right rear tire. Decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire. Decrease the air pressure until the horn sounds. T raining is complete after the horn sounds for the last tire trained (driver’ s side rear tire) and the TPMS indic[...]

V EHICLE LOADING This section will guide you in the proper loading of your vehicle to keep your loaded vehicle weight within its design rating capability . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle?[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 147 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Pr[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. GVW (Gross V ehicle W eight) – is th[...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . W ARNING: Do not exceed the GVWR or the GA WR specified on the S[...]

W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations. W ARNING: Exceeding any vehicle weight rating limitation could result in [...]

you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (45 kg) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400[...]

RECREATIONAL TOWING Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. These guidelines are designed to ensure that your transmission is not damaged. Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from en[...]

STARTING Positions of the ignition 1. O (off) — locks the steering wheel, automatic transmission gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off. 2. I (accessory) — allows the electrical accessories such as the radio to operate while the engine is not running. 3. II (on) — all ele[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. Before starting[...]

3. T urn the key to II (on) without turning the key to III (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key to II (on) without turning the key to III (start). 2. T urn the key to III (start), [...]

Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air . ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and allows the heater[...]

• T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two pronged (cheater) adapters. Also ensure that the block heater , especially the cord, is in good condition before use. • Make sure that when in operation, the extension cord plug /engine block heater cord plug connection is free and clear [...]

Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the A[...]

Parking brake T o set the parking brake (1), pull the parking brake handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. T o release, press and hold the button (2), pull the handle up slightly , then push the handle down. W ARNING: Always set the parking brake fully an[...]

ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC 姞 ) STABILITY ENHANCEMENT SYSTEM W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the Advanc[...]

• Electronic Stability Control (ESC), which functions to help avoid skids or lateral slides • Roll Stability Control™ (RSC 威 ), which functions to help avoid a vehicle roll-over . The AdvanceT rac 威 with RSC 威 system automatically enables each time the engine is started. All features of the AdvanceT rac 威 with RSC 威 system (TCS, ESC[...]

During T raction Control events the “sliding car” icon in the instrument cluster will flash. If the T raction Control system is activated excessively in a short period of time, the braking portion of the system may become temporarily disabled to allow the brakes to cool down. In this situation, T raction Control will use only engine power reduc[...]

During an event that activates the Roll Stability Control™ (RSC 威 )t h e “sliding car” icon in the instrument cluster will flash. Certain adverse driving maneuvers may activate the Roll Stability Control system, which include: • Emergency lane-change • T aking a turn too fast • Quick maneuvering to avoid an accident, pedestrian or obs[...]

PREPARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher cente[...]

the van on a regular basis. These drivers will gain valuable experience handling the van. This experience will help make each trip safer . The van should be operated at a safe speed which, in some conditions, may be less than the posted speed limit. Further , all occupants should be properly restrained. Most people killed in rollover crashes were u[...]

BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal pressed: 1. Apply [...]

AUTOMATIC TRANSMISSION OPERATION Understanding the gearshift positions of the 4–speed automatic transmission This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or r[...]

N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy . T ransmission operates in gears one through four . D (Drive) without Overdrive Overdrive can be deactivated by pressi[...]

1 (First) This position allows for first gear only . • Provides maximum engine braking. • Selecting 1 (First) at higher speeds will cause the transmission to downshift to first gear once the vehicle has slowed down to the appropriate speed. Note: 2 (Second) and 1 (First) are not intended for use under extended or normal driving conditions and r[...]

The RSS detects obstacles up to 6 feet (1.8 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound con[...]

When driving through water , traction or brake capability may be limited. Also, water may enter your engine’ s air intake and severely damage your engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Once through the[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadsi[...]

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arranty’ s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our webs[...]

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. The fuel pump shut-off switch is accessible from behind the glove box. The button will be raised when the sw[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

Passenger compartment fuse panel The fuse panel and relay box are located below the instrument panel to the left of the steering wheel. The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 120 — Headlamps, Daytime Running Lamps (DRL) relay 121 — Not used 122 — Rear window defroster relay 123 — Heater blower[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 131 5A Power mirrors 132 10A Light switch, Exterior lighting 133 — Not used 134 — Not used 135 — Not used 136 15A Horn 137 7.5A Tire Pressure Monitor System (TPMS), Radio, Instrument cluster 138 — Not used 139 — Not used 140 — Not used 141 10A Rear fog lamps 142 15A Brake lamps 143 [...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 159 — Not used 160 — Not used 161 7.5A Anti-lock Brake System (ABS)/T raction control, Steering angle sensor 162 7.5A Airbag module, Passenger airbag off indicator 163 20A Locks 164 — Not used 165 — Not used 166 25A Front power windows 167 7.5A Rear window defroster/heated mirror switch[...]

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always repla[...]

The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected circuits 1 — Not used 2 40A** Passenger compartment fuse panel 3 20A** Ignition switch 4 20A** Fuel pump 5 10A* Powertrain control module (PCM) keep alive power , Canister solenoid 6 15A* PCM, Data link connector 7 10A* Backup lamps 8 15A* Headlamps 9 40A**[...]

Fuse/Relay Location Fuse Amp Rating Protected circuits 22 10A* PCM, Auxiliary connector 23 10A* Right low beam headlamp 24 10A* A/C clutch solenoid 25 10A* Left low beam headlamp 26 10A* Mass air flow sensor , Brake switch, Backup lamps relay 27 — Not used 28 15A* PCM vehicle power 1 29 15A* Auxiliary connector 30A 70A Relay Cooling fan high rela[...]

Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensors, refer to T ire pressure monitoring system (TPMS) in the T ires, Wheels and Loading chapter . Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the TPMS sensor for [...]

• Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • T ry to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling[...]

Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible. Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off. Removing the spare tire The jack and tools are located behind a cover in[...]

3. Detach the first cable by pulling up the cap and sliding it away from the wheel. Then turn the end of the cable so it fits through the slot and remove the cable and bracket. 4. Detach the second cable by unscrewing the bolt. Tire change procedure W ARNING: When one of the front wheels is off the ground, the transmission alone will not prevent th[...]

1. Block the diagonally opposite wheel. 2. Attach the chisel clip to the end of the wrench. Insert the flat end between the rim and the wheel cover and carefully remove the cover . 3. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Roadside Emergencies 186 2010 Transit Connec[...]

4. Align the slot on top of the jack with the sheet metal flange indicated by the jack locator triangle next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not s[...]

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing up toward the vehicle. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center . Pull on the cables to align the c[...]

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 66 90 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended rep[...]

JUMP STARTING W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmiss[...]

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + ?[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, [...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • V ehicle is facing forward so that it is be[...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB A[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. T elephone: ([...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Neve[...]

• After polishing chrome bumpers, apply a coating of Motorcraft Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is[...]

• Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time. • Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuel[...]

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side[...]

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • A void cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area he[...]

• If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). In Canada, use Motorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleani[...]

Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft T ire Clean and Shine (ZC-28) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Wheel and T ire Cleaner (ZC-37-A) Cleaning 210 2010 Transit Connect (tst[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Customer Information Guide to find out which parts and servi[...]

OPENING THE HOOD 1. Lift and swivel the hood badge back. 2. Insert the key and turn it to the left to release the primary latch. Then, turn they key to the right to release the secondary latch. Note: T o prevent damage to, or loss of the key , remove the key immediately after opening the hood and swivel the badge back. 3. Lift the hood and support [...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Engine oil filler cap 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. W indshield washer fluid reservoir 7. Air filter assembly 8. Automatic transmission fluid dipstick 9. Engine oil dipstick 10. Power steering fluid reservoir 1 2 3 4 56 10 9 8 7 Mainte[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. T urn the blade at an angle from the wiper arm. Press the lock tab to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at[...]

• If the oil level is between the MIN and MAX marks , the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough engine oil to raise the level within the MIN and MAX range. Refer to Adding engine oil in this chapter . • Oil levels above MAX mark may cause engine damage. If the engine is overfilled, some [...]

Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the Internatio[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Als[...]

W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medi[...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and underst[...]

• Add Motorcraft Specialty Orange Engine Coolant with Bittering Agent, or equivalent meeting Ford specification WSS-M97B44-D. Refer to Maintenance product specifications and capacities in this chapter . • Do not add/mix a Y ellow or Green type of engine coolant such as Motorcraft Premium Gold Engine Coolant or equivalent meeting Ford specificat[...]

Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure be[...]

Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Maintenance product specifications and capacities in this chapter . Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34°F [–36°C]): [...]

W ARNING: If fail-safe cooling activates, pull off the road as soon as safely possible, and turn the engine off, because the engine may automatically shut off while driving without further indication. How fail-safe cooling works If the engine reaches a preset over -temperature condition, the engine will automatically switch to alternating cylinder [...]

FUEL FILTER Y our vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions W ARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and f[...]

• A void inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury . • A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), fl[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

2. Unlock the fuel filler door . 3. Carefully turn the filler cap counterclockwise until it spins off. 4. Pull to remove the cap from the fuel filler pipe. 5. T o install the cap, align the tabs on the cap with the notches on the filler pipe. 6. T urn the filler cap clockwise 1/4 of a turn until it clicks at least once. 7. Lock the fuel filler door[...]

Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded fuel or any other fuel. The use of leaded fuel is prohibited by law and could damage your vehicle. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, includ[...]

Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality , per the recommendations in the Choosing the right fuel section. Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle[...]

empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty . The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the a[...]

economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy . In general, lower temperatures give lower fuel economy . Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of varia[...]

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boar[...]

The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equiva[...]

a malfunction. T emporary malfunctions may cause the service engine soon indicator to illuminate. Examples are: 1. The vehicle has run out of fuel—the engine may misfire or run poorly . 2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel cap may not have been securely tightened. See Fuel filler cap in th[...]

for 15 seconds without cranking the engine. If the service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system is designed to check the emission control system during normal driving[...]

BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; se[...]

4. Place the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remov[...]

If necessary , add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct. After adding fluid, wait 20 minutes before checking the fluid level in order to allow the level to stabilize. If an overfill occurs, excess fluid should be removed by an authorized dealer . If the fluid level is above the MAX mark, fluid wil[...]

6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not [...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Brake fluid Between MIN and MAX on reservoir Motorcraft Super DOT 4 Motor V ehicle Brake Fluid YS4Z-19542-AA / ESD-M6C57-A or WSS-M6C57-A2 Door latch, hood latch, auxiliary hood latch, seat tracks. — Multi-Purpose Gre[...]

Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Engine coolant 6.1 quarts (5.7L) Motorcraft Specialty Orange Engine Coolant with bittering agent (US) / Motorcraft Specialty Orange Engine Coolant (Canada) 4 VC-3-B (US) CVC-3-B (Canada) / WSS-M97B44-D Cooling system stop leak pellets — Motorcraft Cooling System Stop[...]

Item Capacity Ford Part Name or Equivalent Ford Part Number / Ford Specification Fuel tank 15.1 gallons (57.1 L) —— 1 Approximate dry fill capacity including transmission fluid cooling system, actual refill capacities will vary based on vehicle application and transmission fluid cooling system (i.e. coolers size, cooling lines, auxiliary cooler[...]

ENGINE DATA Engine 2.0L I4 engine Cubic inches 121 Required fuel 87 octane Firing order 1–3–4–2 Ignition system C.O.P Compression ratio 10.0:1 Spark plug gap .051 inch +/- .002 (1.3 mm +/- .05) Maintenance and Specifications 245 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label i[...]

V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross [...]

T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code Four -speed automatic (4F27E) D2 Maintenance and Specifications 248 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GA WR as indicated on the Safety Compliance Certifi[...]

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Components There [...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 253 2010 Transit Connect (tst) Owners Guide (own2002) , 1st Printing USA (fus)[...]

A AdvanceT rac .............................. 160 Air cleaner filter ............... 240–241 Airbag supplemental restraint system ..................................92, 101 and child safety seats .............. 94 description ........................92, 101 disposal .................................... 103 driver airbag ......................94, 1[...]

Cleaning your vehicle engine compartment .............. 206 instrument panel .................... 208 interior ..................................... 208 plastic parts ............................ 207 safety belts .............................. 208 washing .................................... 204 waxing ..................................... 205 whee[...]

F Fail safe cooling ........................ 224 Fluid capacities ......................... 242 Four -Wheel Drive vehicles preparing to drive your vehicle ..................................... 164 Fuel ............................................ 226 calculating fuel economy ....... 231 cap ........................................... 228 capacity .[...]

L Lamps bulb replacement specifications chart .................. 42 daytime running light ...............38 headlamps ................................. 38 headlamps, flash to pass .......... 39 instrument panel, dimming ..... 39 interior lamps .....................41, 43 replacing bulbs .........................44 LA TCH anchors ...................[...]

Safety restraints ........ 80, 83, 85–87 Belt-Minder 威 ............................. 88 for adults ............................. 85–86 for children ............................. 104 Occupant Classification Sensor ........................................ 81 warning light and chime .......... 88 Safety restraints - LA TCH anchors ..............[...]

V V ehicle Identification Number (VIN) .......................................... 247 V ehicle loading .......................... 146 V entilating your vehicle ........... 156 W W arning lights (see Lights) .......12 W asher fluid .............................. 214 W ater , Driving through ............. 170 W indows power ..........................[...]