Frymaster KSCF18G Series manuale d’uso

PARTS LIST INCLUDED Frymaster, a member of the Commercial Foo d Equipment Ser vice Association, recommends using CFESA Certified Tec hnicians. 24-Hour Service Hotline 1-800-551-8633 MARCH 2007 *8195712* NON-CE & KSCF18G Cool Zone Series Gas Fryers Installation, Operation, Service, & Parts Manual[...]

Please read all sections of this manual and retain for future reference. NOTICE This appliance is intended for professional use only and is to be operated by qualified personnel only. A Frymaster and Dean Factory Authorized Service Center (FASC) or other qualified professional should perform installation, maintenance, and repairs. Installation, mai[...]

DANGER Adequate means must be provided to limit the movement of this appliance without depending upon the gas line connection. Single fryers equipped with legs must be stabilized by installing anchor straps. All fryers equipped with casters must be stabilized by installing restraining chains. If a flexible gas line is used, an additional restrainin[...]

KSCF18G Cool Zone Gas Fryers INSTALLATION & OPERATION MANUAL TABLE OF CONTENTS Page # 1. INTRODUCTION 1-1 2. IMPORTANT INFORMATION 2-1 3. INSTALLATION INSTRUCTIONS 3-1 4. DAILY OPERATION 4-1 5. FILTRATION 5-1 6. PREVENTATIVE MAINTENANCE 6-1 7. TROUBLESHOOTING 7-1 8. PARTS LIST: DOUBLE AND TRIPLE UNITS (218/318) 8-1 9. PARTS LIST: SINGLE UNITS ([...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 1: INTRODUCTION 1-1 1.1 Applicability and Validity The KSCF18G Cool Zone Series gas model fam ily has been approved by the European Union (EU) for sale and installation in the follow ing EU countries: AT, BE, KE, KD, ES, FI, FR, GB, IE, IT, LU, NL, NO, PT and SE. This manual is applicable to and valid for[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 1: INTRODUCTION 1-2 1.4 Service Information Call the Frymaster Service Hotline, 1-800-551-8633, for the location of your nearest factory authorized service center ( FASC ). To assist you mo re efficien tly, always provide the service technician with the model number, gas type, se rial number, and the natu[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 1: INTRODUCTION 1-3 1.6 Safety Information (cont.) DANGER DANGER boxes contain information about actions or conditions, which may cau se or result in injury to personnel , may cause dam age to your system, and/or cause your system to malfunction. 1.7 Service Personnel A. Qualified and/or Authorized Operat[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-1 2.1 Receiving and Unpacking Equipment A. Check that the container is uprigh t. Use an outward prying m otion - no hammering - to remove the carton. Unpack the fryer carefully and rem ove all accessories from the carton. Do not discard or misplace these, as they will be needed.[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-2 2.3 Principles of Operation The incoming gas flows through orifices and is mixed with air in the burners to create the correct ratio for proper combustion. The mixture is ignite d at the f ront end of each heat tube by th e pilot light. Internal diffusers slow the flame as it [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-3 2.5 Pre-Installation (cont.) DANGER This appliance must be installed with su fficient ventilation to prevent the occurrence of unacceptable concentrations of substan ces harmful to the health of personnel in the room in which it is installed. B. Clearances : The fryer area mus[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-4 2.6 Air Supply and Ventilation DANGER Do not connect this appliance to the gas supply before reviewing each step in this section. A. Keep the area around the fryer clear to prevent ob struction of combustion and ventilation airflow and to allow for service and maintenan ce. Al[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-5 2.8 Conversion of Units Pressure: 1 mbar = 10.2 mm water colum n (mm W.C.) = 0.4 Inch W.C. 20 mbar = 204 mm W.C. = 8 Inch W.C. 1 inch W.C. = 25.4 mm W.C. = 2.5 mbar Heat Input: 1 kW = 3410 BTU/hr 100 BTU/hr = 0.0293 kW Temperature: 0º Celsius = 32º Fahrenheit Temperature in [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 2: IMPORTANT INFORMATION 2-6 2.9 Restraining the Fryer (cont.) NOTE : If you need to relocate a fryer installe d with legs, rem ove all weight from each leg before moving. If a leg is damaged, contact your service agent for imm ediate repair or replacement. DANGER Hot oil can cause severe burns. Avoid con[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-1 3.1 Installing the Fryer Qualified, licensed, authorized installat ion or s ervice personnel only (as defined in Section 1.7) should perform the following: 1. Installation and service of Frymaster equipment; 2. Conversion of this appliance from one gas type to another. Fai[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-2 3.2 Leg and Caster Installation (cont.) 2. When positioning the fryer, gently lower it into position to prevent undue strain to the legs and internal mounting hardware. If possible, us e a pallet or lif t jack to lift and position the fryer. Tilting the fryer may damage th[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-3 3.3 Leveling the Fryer (cont.) • Legs (Only) 1. Adjust leg height with an adjustable or 1 1 / 16 -inch (27-mm) open-end wrench by turning the hex bullet on the bottom of the leg. 2. The hex bullet is for minor leg height adjustment onl y. Do not adjust more than 1 inch ([...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-4 3.3 Leveling the Fryer (cont.) ANSI Z83.11/11a-(Latest Edition) requires a fry er be restrained to prevent tipping when installed in order to avoid the splashing of ho t liquid. The means of restraint may be the manner of installation, such as connection to battery of appl[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-5 3.4 Gas Connections (cont.) Supply Line Specifications The gas supply lines must be sized as indicated in the chart below, based on the total number of fryers connected to the main gas supply. Recommended Gas Supply Line Sizes Gas Types Number of Fryers 1 2 to 3 4 or more*[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-6 3.4 Gas Connections (cont.) Rigid Connections Check any installer-supplied intake pipe(s ) visually and clean metal particle s or other foreign matter from the threads before installing into a service line . If the intake pipes are not clear of all foreign matter, the orif[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-7 3.4 Gas Connections (cont.) WARNING Use a diluted soap solution to find poten tially dangerous gas leaks when making new connections. B. Regulators: Gas regulators can be adjusted in the field, but no adjustments should be made unless the regulator is out of adjustment or [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-8 3.4 Gas Connections (cont.) 4. If it is necessary to dis conn ect the restraint, it must be reconnected after the fryer has been returned to its orig inally installed position. WARNING Do not attach accessories to this fryer unless fryer is secured from tipping. Personal i[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-9 C. Adjustments for different gases are as follows: GAS PRESSURE AT REGULATOR ORIFICE SIZE (# / MM) GAS TYPE MBAR INCH W.C. BURNER MARKING PILOT MARKING #42 / 2,40 #42 / 2,40 #53 / 1,51 G20 G25 G31 10,0 15,0 27,0 4,0 6,0 10,8 Blue Blue Red 26N 26N 16LP NOTE: Outlet gas pres[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-10 3.7 Gas Conversion: Procedures (cont.) When converting from G20 (20 mbar) to G25 (25 m ba r), or vice-versa, or G31 (37 mbar) to G31 (50 mbar), the following procedures apply: • Check pilot adjustment a nd adjust as necessary. • Other adjustments are not necess ary. C[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-11 3.8 Electrical Connections DANGER This fryer is equipped with a three-pr ong (grounding) plug for protection against electrical shock and must be plugged directly into a properly grounded, three-prong receptacle. DO NOT CUT, REMOVE, OR OTHERWISE BYPASS THE GROUNDING PRONG[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-12 3.9 Safety Switches (cont.) B. Other Fryer/Filter Switches 1. Drain Valve Microswitch: The computer will display DRAIN OPEN when the drain valve is opened. The computer will lockout, preventing any cooking operation until EXIT/COOL FI LTER is pressed. 2. Float-Switch: Loc[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-13 3.9 Safety Switches (cont.) C. Filtering: Drain Valve and Oil Return Handles 1. Drain Valve Handle: RED HANDLE. Push the red handle (located in the fryer cabinet) to the right to open the drain valve when filtering. After all oil has drained from the frypot and/or polishi[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-14 3.10 Initial Cleaning Before Startup New units are wiped clean with solvents at the fact ory to remove any visible signs of dirt, oil, and grease remaining from the m anufacturing process. Th en, they are coated li ghtly with oil. W ash thoroughly with hot, soapy water to[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 3: INSTALLATION INSTRUCTIONS 3-15 3.11 Final Preparation (cont.) NOTE: If the float s witch is blocked in "down posi tion" w ith solid shortening, the fryer will not heat. Always ensure that the float s witch is in the "up" position when packing solid shortening into fry pot. 5. KFC-1 [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 4: DAILY OPERATION 4-1 4.1 General Use 1. At opening, always check that the powe r switch and the computer are OFF. 2. For consistent quality product, convenience, and long-term sa vings, use a high-quality liquid shortening. 3. If using solid shortening, never melt a block of shortening by placing an ent[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 4: DAILY OPERATION 4-2 4.2 Start-Up Procedures (cont.) g. If the pilot does not stay lit, depr ess the wh ite pilot light button and re -light the pilot (repeat Step f above). Hold the button in longer before releasing. Trapped air may necessitate re-lighting the pilot seve ral tim es until gas f low is c[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 4: DAILY OPERATION 4-3 DANGER The crumb tray in fryers equipped with a filter sy stem must be emptied into a fireproof container at the end of frying ope rations each day . Some food particles can spontaneously combust if left soaki ng in certain shortening material. WARNING Filter one frypot at a time. T[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-1 5.1 General WARNING The on-site supervisor is responsible for ensuring that operators are made a ware of the inherent hazards of operating a hot oil filtering system, particularly the aspects of oil filtration, draining, and cleaning procedures. To conduct filter operations with the KFC-[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-2 5.2 Filter Preparation (cont.) 1. Put on protective gear/gloves. Pull th e f ilter pa n ou t of the filter cabinet. R emove cover. 2. Remove crumb screen. If crumbs are present in the crumb screen, empty the screen into a fireproof container. Thoroughly wash the screen in hot, soapy wa t[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-3 5.2 Filter Preparation (cont.) 5. Remove the filter screen f rom the bottom of the pan. 6. Thoroughly clean the pan and all pan components as described for the crumb screen (Step 2). 7. Inspect the pickup tube a nd ensure vent hole is open and free of shortening/debris.[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-4 5.2 Filter Preparation (cont.) 8. Replace filter screen and drape one sheet of filter paper across the filter pan. The filter screen must be installed prior to filter paper placement or the filter won’t operate correctly. 9. Reinstall the hold-down ring. Ensure filter paper is properly[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-5 5.3 Filter Operations NOTE: Whe n left and right are indicated, refer to the operator’s left and right. DANGER Draining and filtering of cooking oil or s hortening must be accomplished with care to avoid a serious burn caused by careless handling. The oil to be filtered is at or near 3[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-6 5.3 Filter Operations (cont.) 2. Remove the support grid from the frypot using the clean-out rod. Stir the oil with the L-shaped Teflon brush to suspend debris prior to draining. 3. Open the fryer drain valve by pushing the red handle (under the frypot to be filtered) to the right until [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-7 5.3 Filter Operations (cont.) 4. Use the L-shaped brush to scrub the frypot, and to assist in sediment removal. Brush the frypot sides and betw een the tubes to remove debris. Use the clean-out rod to clear the drain if necessary. 5. Open the oil return valve by pulling and turning the h[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 5: FILTRATION 5-8 5.3 Filter Operations (cont.) 8. Turn off the filter by turning the oil return handle to the CLOSED position and pushing the oil return handle in until it stop s. This closes the oil return va lve under the filtered fry pot and stops the filter pump motor. 9. Repeat Steps 1 and 2 in Sect[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 6: PREVENTATIVE MAINTENANCE 6-1 Well-maintained equipment operates more efficiently and lasts longer. Keep the fryer clean during the day and thoroughly clean it at the end of each day. DANGER Never attempt to clean the fryer during th e cooking process or when the frypot is filled with hot oil. If water [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 6: PREVENTATIVE MAINTENANCE 6-2 6.3 Periodic/Annual This appliance should be inspecte d and adjusted period ically by qualified serv ice personnel as part of a regular kitchen maintenance program. Frymaster and Dean recommend that a Factory Au thorized Service Techni cian should inspect this appliance at [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 6: PREVENTATIVE MAINTENANCE 6-3 6.3 Periodic/ Annual (cont.) Check filtration system integrity as follows: • With the filter pan empty, place each oil return handle in the OPEN position, one at a time. Using rear flush oil return, verify that the pump activates and that bubbles appear in the oil of the [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-1 7.1 Introduction This section provides an easy reference guide to some of the common problems that m ay occur during the operation of this equipment. The trou bleshooting guides that follo w are intended to help correct, or at least accurately diagnose, problems w ith this equipment[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-2 7.2 Fryer Troubleshooting 7.2.1 Computer fails to turn ON when ON/OFF button is pressed. 1. Check wall circuit breakers. Reset, if necessary. 2. Check fryer connection to external power source. 3. Disconnect fryer from power supply. 4. Check fuses and replace, if necessary (see phot[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-3 7.2 Fryer Troubleshooting (cont.) 7.2.3 (cont.) Actual frypot temperature differs from computer setpoint temperature. 5. The thermometer tem perature should be within ± 10°F ( ± 5°C) of the computer display temperature. Yes: System is maintaining temperatur e properly. Frypot Fr[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-4 7.2 Fryer Troubleshooting (cont.) 7.2.4 DRAIN OPEN message remains after closing drain valve. 1. Computer was turned OFF while draining frypot. 2. Close drain valve. Turn computer OFF and ON again. Computer display will read ON. 3. Open drain valve. Computer display will read DRAIN [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-5 7.2 Fryer Troubleshooting (cont.) 7.2.6 Main bur ner malfunc tions. A. Main burner will not ignite; no gas is present at main burner. 1. Check that float switch is not stuck in the "down" position. 2. Check and reset the high-limit switch. 3. The combination gas valve and/[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-6 7.3 Filtration System Troubleshooting Pump won't start. • Return valve not fully opened . • Tripped circuit brea ker . • Incorrect or no li ne voltage. • Failed return microswitch . Pump stops during filteri ng process. Motor is hot. • Allow motor to cool for at least[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-7 7.4 Wiring Diagrams 7.4.1 Normally Open Float S witch (Right)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-8 7.4.2 Normally Open Float S witch (Left)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-9 7.4.3 CE, Normally Open Float S witch (Right)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-10 7.4.4 CE, Normally Open Float S witch (Left)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-11 7.4.5 Fast Ready 218G (KSCF21 8GP00001)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-12 7.4.6 Fast Ready 218G (KSCF21 8GP00001, KSCF218G N00007)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-13 7.4.7 Thermatron, 230V CE[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-14 7.4.8 Constant Pilot, Fast Ready 218G[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-15 7.4.9 Constant Pilot with KFC-1, 218G[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-16 7.4.10 Oil Return, 218G/318G ( with Vent Solenoids)[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-17 7.4.11 CE, Single[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-18 7.4.12 Oil Return, Single[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 7: TROUBLESHOOTING 7-19 7.4.12 Oil Return, Single[...]

KSCF18G COOL ZONE SERIES GAS FRYERS C HA P T E R 8 : PA R T S L I ST : D O U B L E & T R I P L E U NI T S (218G/318G) For parts and/or components no t listed, contact the Frym aster Service Hotline at 1-800-551-863 3 or 1-318-865-1711 for additional service and parts information. 8.1 Cabinetry and Related Components A 30 29 8 18 19 3 17 10 4 16[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-2 8.1 Cabinetry and Related Components (cont.) ITEM PART # COMPONENT 1 201-9081 Side, Cold Rolled Steel Cabinet, Left 2 202-9081 Side, Cold Rolled Steel Cabinet, Right * 211-9606 Side, Stainless Steel Cabinet, Left * 212-9606 Side, Stainless Steel Ca[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-3 8.2 Accessories ITEM PART # COMPONENT 1 803-0306 Twin Fry Basket 2 211-8178 Joiner Strip (to mount unit to the left of a 2424G) 3 212-8178 Joiner Strip (to mount unit to the right of a 2424G) 4 823-5404 Drain Tube (to attach unit drain to a 2424G) [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-4 8.3 Component Box, Computers, and Related Components 1 2 3 4 5 6 7 8 9 4 10 13 12 11 Speaker mounts directly into component box.[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-5 8.3 Component Box, Computers, and Related Components (cont.) ITEM PART # COMPONENT 1 824-1465 Component Box 2 807-4114 Relay, DPDT, 24VAC * 106-1414 Relay Socket * 807-3613 Relay Spring * 200-1337 Relay Bracket with 1 cutout 3 807-0855 Transformer,[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-6 8.4 Drain Valve, Oil Retu rn, and Related Components Oil Return Valves, Fittings, and Components (106-4717) 11 12 13 14 15 16 28 27 11 17 18 19 22 21 23 24 25 26 3-Way Valve Assembly (Item 13 above, 106-4763) Included with It em 8 10 7 2 5 6 3 4 1 [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-7 8.4 Drain Valve, Oil Return, and Related Components (cont.) ITEM PART # COMPONENT 106-4672 Drain Valve and Microswitch Components 1 106-1401 Bracket, Microswitch 2 210-9374 Bracket, Activator- Microswitch 3 200-9345 Handle, Drain Valve * 823-5181 H[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-8 8.5 Filter Pan and Related Components 6 5 4 3 2 1 10 8 9 11 7 Comp letely Assembled Filtration Un it[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-9 8.5 Filter Pan and Related Components (cont.) ITEM PART # COMPONENT Filter Pan Assembly 1 823-5214 Pan, Filter 2 106-7330 Screen, Filter 3 803-0299 Paper, Filter 4 810-2911 Ring, Hold-Down 5 823-4832 Crum b Basket 6 106-4693 Lid, Filter Pan 7 810-0[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-10 8.6 Frypot and Related Components 1 2 3 6 5 4 7 8 9 11 10 ITEM PART # COMPONENT 1 823-4884 Frypot, Stainless Steel, with 1½" Drain * 803-0149 Grid, Frypot 2 210-8387 Diffuser Assembly 3 200-1615 Support, Manifold 4 810-2151 Burner, Left 5 81[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-11 8.7 Gas Valves, Pilot Assemblies, and Related Components 1 2 7 8 9 3 4 5 6 Non-CE Gas Valve(s) CE Gas Valve (s) 12 11 10 13 14 15 16[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-12 8.7 Gas Valves, Pilot Assemblies, and Related Components (cont.) ITEM PART # COMPONENT 1 807-3552 Gas Valve, Natural and Manufactured Gas, 24V (Non-CE) * 807-3628 Gas Valve, LP, 24V (Non-CE) 2 806-6710SP Gas Valve, Natural Gas, 24V ( CE ) * 806-67[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-13 8.8 Over-the-Top Oil Return and Related Components 16 14 1 4 13 11 2 15 10 12 17 6 3 5 8 9 7 18 21 24 22 28 26 25 19 23 29 20 27[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 8: PARTS LIST: DOUBL E & TRIPLE UNITS (218G/318G) 8-14 8.8 Over-the-Top Oil Return and Related Components (cont.) ITEM PART # COMPONENT A 106-2983 Oil Return Assembly 1 823-3344 Handle, Oil Return 2 813-0826 Nipple, ⅜ " x 4, BM 3 813-0780 Bushing, Hex ⅜ " NPT x ½", BM 4 813-0777 Ni[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST: SINGLE UNITS (118G) 9-1 For parts and/or components no t listed, contact the Frym aster Service Hotline at 1-800-551-8633 or 1-318-865-1711 for additional service and parts information. 9.1 Cabinetry and Related Components[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-2 9.1 Cabinetry and Related Components (cont.) ITEM PART # COMPONENT 1 201-1299 Side, Painted Panel, Left 2 202-1299 Side, Painted Panel, Right * 211-4570 Side, Stainless Steel, Left * 212-4570 Side, Stainless Steel, Right * 200-5036 Back, Structural, Over-the-top Oil[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-3 9.2 Accessories ITEM PART # COMPONENT 1 803-0306 Twin Fry Basket 2 211-8178 Joiner Strip (to mount unit to the left of a 2424G) 3 212-8178 Joiner Strip (to mount unit to the right of a 2424G) 4 823-5404 Drain Tube (to attach unit drain to a 2424G) 5 803-0149 Basket [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-4 9.3 Component Box, Computers, and Related Components 1 2 3 4 5 6 7 8 9 4 10 13 12 11 Speaker mounts directly into component box.[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-5 9.3 Component Box, Computers, and Related Components (cont.) ITEM PART # COMPONENT 1 824-1195 Component Box (KCF118GN and KCF118GP) * 824-0941 Component Box (KCF118N and KCF118P) 2 807-4114 Relay, DPDT, 24VAC * 106-1414 Relay Socket (includes item 2) * 807-0012 Rela[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-6 9.4 Drain Valve, Oil Retu rn, and Related Components ITEM PART # COMPONENT 1 106-0754SP Oil Return Handle Assembly 2 813-0644 Nipple, ⅜ " NPT x 1 ½", Black Tube 3 813-0006 Bushing, ½" to ⅜ " NPT, Hex, BM 4 813-0003 Tee, ½" NPT, BM 5 8[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-7 9.4 Drain Valve, Oil Return, and Related Components (cont.) ITEM PART # COMPONENT 6 813-0298 Nipple, ½" NPT x 2", BM 7 813-0165 Elbow, Street, ½" NPT, 90° 8 813-0062 Elbow, ½" NPT, 90°, BM 9 813-0087 Nipple, ½" NPT x 1 ½", BM 10 [...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-8 9.5 Filter Pan and Related Components[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-9 9.5 Filter and Related Components (cont.) ITEM PART # COMPONENT Filter Components 1 823-4439 Pan, Filter 2 106-7331SP Grid, Wire 3 823-5422 Hold Down Ring 4 823-3736 Crumb Basket 5 823-4440 Lid, Filter P an 6 230-0124 Handle, Filter Pan Lid 7 810-2805 Caster, 2"[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-10 9.6 Frypot and Related Components 1 2 3 6 5 4 7 8 9 11 10 ITEM PART # COMPONENT 1 823-4884SP Frypot, Stainless Steel, with 1½" Drain * 803-0149 Grid, Frypot 2 210-8387 Diffuser Assembly 3 200-1615 Support, Manifold 4 810-2151 Burner, Left 5 810-2149 Burner, C[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-11 9.7 Gas Valves, Pilot Assemblies, and Related Components 1 2 7 8 9 Non-CE Gas Valve (s) CE Gas Valve(s) 12 11 10 13 14 15 16 3 4 5 6[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-12 9.7 Gas Valves, Pilot Assemblies, and Related Components (cont.) ITEM PART # COMPONENT 1 807-3552 Gas Valve, Natural Gas, 24V (Non-CE) * 807-3628 Gas Valve, LP, 24V (Non-CE) 2 806-6710SP Gas Valve, Natural Gas, 24V ( CE ) * 806-6711SP Gas Valve, LP, 24V ( CE ) * 81[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-13 9.8 Over-the-Top Oil Return and Related Components[...]

KSCF18G COOL ZONE SERIES GAS FRYERS CHAPTER 9: PARTS LIST : SINGLE UNITS (118G) 9-14 9.8 Over-the-Top Oil Return and Related Components (cont.) ITEM PART # COMPONENT A 106-3347 Oil Return Assembly 1 810-0697 Disconnect, Male 2 813-0003 Tee, ½" x ½" x ½", BM 3 813-0022 Nipple, ½" x Close NPT, BM 4 813-0062 Elbow, ½", BM[...]

Frymaster, L.L.C., 8700 Line Av enue, PO Box 51 000, Shreveport, Louisiana 71135-1000 Shipping Address: 8700 Line Av enue, Shre veport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-31 8-688 -2200 FAX (Call Center) 1-318-219-7135 Price: $10.00 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1-800-551-8633 819-5712 MARCH 2007[...]