Fujitsu 5000 manuale d’uso

DESKPOWER 5000 Series User’s Manual Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability for any error or omission in the same. Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used. To ensure that Fuji[...]

IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near w[...]

■ Greetings We thank you for purchasing the Fujitsu DESKPOWER 5000 personal computer. This manual explains how to use the hardware of the DESKPOWER 5000. Please read this manual carefully to ensure correct use of the DESKPOWER 5000. This unit may malfunction if the power source is interrupted suddenly, for example, due to lightning. Fujitsu recom[...]

■ Conventions used in this manual ● Warning icons Various icons and icon/word combinations are used in this manual to encourage users to use the equipment so as to minimize personal risk and prevent property damage. The icons are explained as follows. The user should be familiar with the icons before responding to the corresponding instructions[...]

● Conventions used in the text of the manual The symbols used in the text of the manual have meanings as explained below: Point indicates information necessary to run hardware or software. Help indicates information explaining how to terminate an incorrect operation or troubleshoot. ● Screen display examples Screen displays provided in this man[...]

■ Warning and caution labels The PC bears warning and caution labels as shown below. The warning and caution labels must not be removed or damaged. ● Rear of the PC main unit W ARNING ● Before mounting or dismounting an optional unit in/from your PC, switch off the PC and all connected units and unplug all power cords from respective outlets [...]

Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables. Consult this chapter before assembling the PC. Chapter 2 Basic Operations This chapter explains basic operations required to use the PC, such as how to switch the power on and off and how to[...]

Content Chapter 1 Installation and Connection ............................................ 1 1 Installation ............................................................................. 2 Installation location .................................................................................... 2 Example of installing the PC ........................[...]

Chapter 3 Installing Internal Options ............................................. 19 1 Introduction ......................................................................... 20 Handling precautions ............................................................................... 20 Installing positions of internal options ..........................[...]

Appendix .......................................................................................... 53 1 Name and Function of Each Component .......................... 54 F ront of the PC main unit ......................................................................... 54 Rear of the PC main unit ..................................................[...]

Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables. 1[...]

2 This section provides notes on installing and using the PC. ■ Installation location Do not install the PC in the following areas: - Area exposed to moisture, dust, or smoke - Area poorly ventilated - Area having open flames - Area that may expose the PC to water - Area exposed to direct sunlight or high temperatures. - Area having temperatures [...]

3 ■ Preventing electromagnetic interference with a TV or radio Your PC complies with the VCCI Standard restricting electromagnetic interference with a TV or radio. However, the computer may interfere with a TV or radio depending on the installation location. To prevent the PC from interfering with TV or radio reception, note the following: ● Pr[...]

4 W ARNING ● To prevent electric shock, ground the device (if required) before providing power to the equipment. To prevent fire, do not connect the ground wire to a gas pipe. ● To prevent electric shock, unplug the PC main unit and connected equipment before attaching and detaching a CRT display, keyboard, mouse, LAN cables, and power cords. ?[...]

5 ■ Attaching CRT display, keyboard, mouse, and LAN cables ¤ ¤ ¤ ¤ ¤ Point This section explains how to connect the CRT display so as to supply power from the PC main unit. In this case, the power cord included with the CRT display is not used. Connect the power cord to the CRT display. Secure one end of the power cord (for CRT) to the inlet[...]

6 ■ Connecting the power cord After connecting the display and other peripherals to the PC main unit, note the following when connecting the power cord of the PC main unit. - Do not plug or unplug the power cord with wet hands. - Do not damage or remodel the power cord. - Do not bend, stretch, or place heavy objects on the power cord. - Do not us[...]

7 Chapter 2 Basic Operations This chapter explains basic operation methods of the PC such as how to turn the power on and off and handle storage media. 2[...]

8 This section explains how to switch on the PC. CA UTION ● To prevent malfunction after turning on the PC, do not move equipment or subject equipment to shock and/or vibration. 1 Press the power switch of the CRT display. There is no display. 2 Press the power switch of the PC main unit. The power lamps of the PC main unit and CRT display light [...]

9 ¤ ¤ ¤ ¤ ¤ Point - Before switching on the PC, make sure that display is connected. If the PC is switched on before the display is connected, the display adapter may not be recognized, and the screen may not be displayed normally. In this case, connect the display, terminate the OS, switch off the PC, and then switch on the PC again. - If the[...]

10 ■ Turning off the power via Windows 98 1 Click [Start]. The "Start" menu appears. This section explains how to turn off the PC. ¤ ¤ ¤ ¤ ¤ Point - Before turning off the power, terminate all jobs and save all necessary data. - Before turning off the power, confirm that the access indicator lamps ( see Appendix 1, "Name and F[...]

11 3 Check that "Shut down the computer?" has been selected and then click [OK]. The power is turned off automatically. ¤ ¤ ¤ ¤ ¤ Point If "APM Power Controls" on the BIOS setup menu is set to "Disabled," the message "The computer is ready for shut down" is displayed. Since power is not automatically tur[...]

12 The PC is reset after the operating system in configured or if software fails to run normally. This section explains how to reset the PC. ¤ ¤ ¤ ¤ ¤ Point Resetting the PC results in memory data being lost. Before resetting, save all necessary data. ■ Resetting the PC via Windows 98 This section explains how to reset the PC via Windows 98.[...]

13 ■ Resetting the PC via Windows 2000 This section explains how to reset the PC via Windows 2000. 1 Click [Start] and "Shut Down". The "Shut Down Windows" dialog box appears. 2 Select [Restart] and click [OK]. The PC is reset. ¤ ¤ ¤ ¤ ¤ Point The following procedure can also be used to reset the PC: 1 Press [Ctrl] + [Alt[...]

14 A floppy disk is a storage medium used to save programs and other information. This section explains how to mount and dismount floppy disks. ¤ ¤ ¤ ¤ ¤ Point Use a floppy disk formatted for DOS. If a disk other than DOS is used, the operation may not execute correctly. ■ Handling precautions To prevent malfunctions, note the following prec[...]

15 ● Dismounting a floppy disk 1 Confirm that the floppy disk access indicator lamp is off. ¤ ¤ ¤ ¤ ¤ Point To prevent data from being destroyed, do not dismount a floppy disk from the drive when the floppy disk access indicator lamp is on. 2 Press the floppy disk eject button. The floppy disk is ejected. Floppy disk access indicator lamp[...]

16 Your PC incorporates a CD-ROM drive(depending on the model). This section explains how to handle, mount, and dismount CD-ROM disks. ■ Handling precautions To prevent malfunctions, note the following precautions regarding CD-ROM disks: - Do not write on the label side (printed side) using a ball-point pen or pencil and do not affix extra labels[...]

17 ■ Mounting and dismounting a CD-ROM disk ● Mounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejected. 2 With the label side of the CD-ROM disk facing up, place the CD-ROM disk in the center of the tray. 3 Press the EJECT button. The tray retracts into the PC main unit and the CD-ROM is set. ¤ ¤ ¤ ¤ ¤ Point - When the CD-ROM[...]

18 Your PC incorporates a built-in hard disk. This section outlines precautions to take when handling a hard disk. ■ What is a hard disk? A hard disk is used to save software and other data and consists of a magnetic disk packed in a box as shown on the right. A hard disk can save more data and can read and write data faster than is possible with[...]

Chapter 3 Installing Internal Options This chapter explains how to install internal options such as hard disk and expansion cards. Consult this chapter as required. 3[...]

20 The features and performance of your PC can be upgraded by installing options. This section describes the types of internal options that can be installed in the PC and explains how to remove the upper cover and front panel in preparation for installing the internal options. ■ Handling precautions Note the following when installing internal opt[...]

21 ■ Installing positions of internal options Built-in hard disk (standard) Replacing a hard disk with larger capacity increases the storage capacity of the PC. 3.5-inch file bay Install 3.5-inch file bay options. The usual devices installed are as follows. - Hard disk (IDE standard, SCSI standard) - Magneto-optic disk drive - 3.5-inch floppy dis[...]

22 ■ Removing the upper cover When installing internal options, remove the upper cover so as to reveal the inside of the main unit. 1 Remove three screws at the rear of the PC main unit. 2 Remove the upper cover. Slide the upper cover to the rear of the PC main unit (in the direction of arrow 1 in the figure) Lift and remove the cover (in the dir[...]

23 ¤ ¤ ¤ ¤ ¤ Point To install a memory module, set up the PC, turn off the power, remove the AC power cord from the outlet and install the memory module. W ARNING ● To prevent electric shock, before installing and removing memory modules, turn off the PC and connected units and unplug power cords from respective outlets. ● To prevent elect[...]

24 ■ Memory A total of up to 512 megabytes of memory modules can be installed. A memory module has been installed in DIMM1 as standard. Install a memory module to be added in DIMM2. To ensure a total of 512 megabytes of memory, replace the memory module in DIMM1 with a 256-megabyte memory module. ¤ ¤ ¤ ¤ ¤ Point Install a Fujitsu genuine mem[...]

25 ■ Removing the memory 1 Remove the upper cover. 2 Open the hooks out at both ends of the slot and remove the memory module. ¤ ¤ ¤ ¤ ¤ Point Note that opening the hooks out forcefully causes the memory card to pop out of the slot and may cause a malfunction. 3 Attach the upper cover.[...]

26 ¤ ¤ ¤ ¤ ¤ Point - To install an expansion card, set up the PC, turn off the power, and install the expansion card. - The first to fourth white slots from the top are for PCI cards. - Only a half-size expansion card can be installed in the first slot from the top. - When an expansion card using a serial port such as a modem card is installed[...]

27 ● To prevent injury and/or malfunction, do not touch PC board components not specified. ● To prevent injury and/or device failure, do not touch the metal bracket on the motherboard at the rear of the PC main unit. To install expansion cards, "resources" must be set. The floppy disk drive or hard disk drive inside the PC uses predet[...]

28 ¤ ¤ ¤ ¤ ¤ Point - A device driver selected by the Plug & Play function has already been registered with Windows 98/2000. However, some device drivers have not been registered with Windows 98/2000, depending on the expansion card or peripheral device. In this case, use the floppy disk included with the expansion card containing the devic[...]

29 Start Before installing the expansion card, check the resources that can be set for the expansion card to be installed. Are the resources required by the expansion card unused resources of the PC? See the manual included with the expansion card. See the manual included with the expansion card. Allocate the resources required by the expansion car[...]

30 ■ Starting and terminating the ICU (For a PC using Windows NT) This section explains how to start and terminate the ICU using Windows NT. 1 If the PC is turned on, turn it off. 2 Confirm that the "boot disk" is in write-enable status, insert in the floppy disk drive, then turn on the PC. MS-DOS is started. 3 Confirm that the "Pl[...]

31 ■ Installing an expansion card To install a large expansion card, remove the motherboard as shown in step 3. To install a small expansion card, steps 2, 3, 7, and 8 are not required. 1 Remove the upper cover. 2 Remove the retaining metal bracket at the side (for installing a large expansion card). Remove the screw, open the retaining metal bra[...]

32 6 Secure the expansion card with the screw. Secure the expansion card with the screw removed in step 4. 7 Install the motherboard (when a large expansion card has been installed). Firmly insert the motherboard and hold it down with the lever. 8 Install the retaining metal bracket at the side (for installing a large expansion card). Insert the ho[...]

33 This section explains how to install expansion bay options such as internal hard disk, magneto-optic disk drive, CD-ROM drive, and floppy disk drive. The power can be supplied from the PC main unit to the expansion bay options, differing from external-type devices; therefore, an outlet is not required. This is also useful in saving space. ¤ ¤ [...]

34 W ARNING ● To prevent an electric shock, turn off the PC and connected units and unplug power cords from respective outlets before installing internal options in, or removing them from the expansion bay. ● To prevent an electric shock, fire, and/or malfunction, install only Fujitsu genuine internal options in the PC expansion bay. CA UTION ?[...]

35 ■ Replacing a internal hard disk equipped as standard This section explains how to replace a standard-equipped internal hard disk with a hard disk of larger capacity. 1 Set up the jumper switch. See the manual accompanying the internal hard disk and make sure that the jumper switch has been set to master, or cable select. 2 If retaining metal [...]

36 6 Replace the internal hard disk. Remove the four blue screws on the back of the retaining metal bracket, and then remove the standard-equipped hard disk. Then, use the blue screws to install the new hard disk. 7 Install the internal hard disk in the PC main unit. Install the retaining metal bracket in the original position by lowering it in the[...]

37 ■ Installing internal options to 3.5-inch expansion bays This section explains how to install 3.5-inch expansion bay options such as a 3.5-inch internal hard disk, magneto-optic disk drive, and 3.5-inch floppy disk drive. A magneto-optic disk drive is used below in an installation example. 1 Set the internal option. See the manual accompanying[...]

38 6 Remove the retaining metal bracket from the PC main unit. Slide the retaining metal bracket toward the rear side of the PC main unit, and then lift and remove the retaining metal bracket. 7 Install a internal option in the retaining metal bracket. Secure the internal option with the four screws that were removed in step 2. - To install a magne[...]

39 9 Connect the flat cable. Connect the flat cable that is appropriate for the internal option to be installed. - To install two IDE-standard internal options to the IDE secondary cable (if one of the options is a hard disk), install the hard disk at the master side. - To install a SCSI interface internal option: Connect the flat cable to the SCSI[...]

40 11 Attach the front panel. Remove the blank panel for a 3.5-inch expansion bay from the rear side of the front panel as required in the arrow direction shown in the figure. 12 Attach the upper cover. 13 Use BIOS setup to configure the internal option. To configure the installed IDE-standard internal option, use the main menu of BIOS setup ( see [...]

41 ■ Installing internal options to 5-inch expansion bays This section explains how to install 5-inch expansion bay options such as CD-ROM drive and 5- inch floppy disk drive. A CD-ROM drive is used below in an example of installation. Up to two 5- inch expansion bay options can be installed in your PC. ¤ ¤ ¤ ¤ ¤ Point The retaining metal br[...]

42 6 Secure the internal option with two screws. 7 Connect the flat cable. Connect the flat cable appropriate for the internal option to be installed. - To install an IDE-standard internal option, connect the flat cable to the master or slave connector according to the setting of the internal option. If a magneto-optic disk has been installed by a [...]

43 8 Connect the power cord. Connect the unused power cord to the connector of the installed internal option. 9 Install the blank panel (for an option that does not require a medium be mounted/ dismounted) Install the blank panel with the screw that were removed in step 4. 10 Attach the front panel. Install or remove the blank panel as required. ¤[...]

44 11 Attach the upper cover. 12 Use BIOS setup to configure the internal option. To configure the IDE-standard installed internal option, use the main menu of BIOS setup ( see "Main Menu," "BIOS Setup"). ¤ ¤ ¤ ¤ ¤ Point BIOS Setup A guide to your Deskpower 5000 BIOS is available online. Please visit our technical support s[...]

45 Chapter 4 Troubleshooting This chapter explains the procedure to follow if the computer does not operate as expected. 5[...]

46 This section provides a list of error messages and suitable responses thereto. Consult this section as required. ■ Error messages displayed by the PC Error Message An error occurred at address xxxx during a system memory test. An error occurred at address xxxx during an additional memory test. System cache error-Cache disabled An error occurre[...]

47 Error Message An invalid hard disk drive was set. Turn the power off, then on again. Confirm BIOS setup items, then save. Because the computer was not booted correctly last time, some of the setup values are reset to defaults. If an error occurs during POST, this message is displayed before the OS boots. Check date and time settings Description [...]

48 Error Message Invalid system disk Non-System disk or disk error Operating system not found An error occurred during execution of the Execution Environment. An error occurred during execution of the Preboot Execution Environment. An error occurred during execution of the Preboot Execution Environment. An error occurred during execution of the Pre[...]

49 ■ Correcting errors If an error message is displayed, respond as follows. - Running the BIOS setup utility If a BIOS setup error message is displayed, retry the BIOS setup utility. - Confirming that built-in options are mounted correctly If optional extension cards are mounted, confirm that the cards are mounted and set up correctly. Also conf[...]

50 This section provides troubleshooting information for each function. Consult this section as required. For troubleshooting information for Windows NT, refer to the Windows NT manual or the online help registered on the Start menu. ■ Troubleshooting information on the computer main unit and peripheral units ● The access lamp does not light up[...]

51 ● The power is not turned on or the Power lamp on the front panel does not light up. Is the power cable plugged in? ● Data cannot be read from the CD-ROM drive. Check the following: - Has the CD-ROM been placed properly at the center of the tray? Place the CD-ROM on the tray again with the label side facing upward. - Has the CD-ROM been plac[...]

52 ● The mouse is disabled and Windows 98 cannot end. Use the keyboard to exit Windows 98 as follows: 1 Press the key or the Ctrl + Esc keys. The Start menu appears. 2 Select "Exit Windows" with the ↑ " or ↓ key and press the Enter key. The Exit Windows dialog box is displayed. 3 Select "Turn off power" and press the [...]

Appendix This appendix explains how to clean the PC and provides PC main unit specifications.[...]

54 This section explains the name and function of each component of the PC main unit, motherboard/ riser board, and keyboard. ■ Front of the PC main unit 1 Name and Function of Each Component Sound volume The sound volume of speakers and headphones can be controlled. Headphone terminal Connect a headphone. USB connector Connect the USB device. Ke[...]

55 Headphone terminal (Only for a music CD) Headphone volume (Only for a music CD) Floppy disk eject button Press this button to eject a floppy disk. 3.5-inch blank panel Remove this panel to add a 3.5-inch internal option. BUSY lamp The lamp is on while reading data from a CD- ROM or playing a music CD. EJECT button Press this button to mount or d[...]

56 ■ Rear of the PC main unit Outlet Connect the power cord of the CRT display. Ventilation holes The heat within the PC main unit is ventilated through these holes. Keep them free. Power-switching switch Inlet Connect the power cord of the PC main unit. SPK OUT terminal Connect the speakers. LINE IN terminal Connect the output terminal of audio [...]

57 USB connector Connect the peripherals conforming to the USB standard. LAN connector ( : NETWORK) Connect the LAN cable. 2 1 Mouse connector ( : MOUSE) The heat within the PC main unit is ventilated through these holes. Keep them free. DVI Connector Connect the display cable conforming to DVI standard Serial connector ( : SERIAL PORT1) ( : SERIAL[...]

58 Riser board Connectors for expansion cards and IDE connectors are installed. 3.5-inch expansion bay Install a 3.5-inch expansion bay option such as magneto-optic disk drive and internal hard disk. 5-inch expansion bays (2) Install 5-inch expansion bay options such as CD-ROM drive and 5-inch floppy disk drive. (To install a 3.5-inch expansion bay[...]

59 ■ Motherboard/riser board JP3 jumper switch Set whether to enable the password. Internal battery The battery is used to store the setup of the PC. The life span of the battery is about five years under normal use condition (8 hours per day). If the upper cover of the PC main unit is left removed, the internal battery life will shorten. Keep th[...]

60 ■ PC main unit specifications Product name CPU BIOS ROM System RAM Floppy disk Hard disk CD-ROM Graphics Sound I/F CRT USB Keyboard Mouse Serial port Parallel port LAN Audio Error monitor function Number of expansion slots DESKPOWER 5000 Pentium III or Celeron 512 KB (FLASH ROM) SDRAM DIMM with 168-pin parity (Supporting ECC) Up to 512 MB 3.5-[...]

61 ¤ ¤ ¤ ¤ ¤ Point Note that the specifications of the PC main unit may change without prior notice. Product name Number of Storage bays Power supply/ frequency Power consumption Weight External dimensions Use environment DESKPOWER 5000 5 Rear: 3.5-inch hard disk (standard feature) Front center: 3.5-inch floppy disk drive (standard feature) Fr[...]

62 LAN controller Send and receive buffer RAM External interface Transmission media Transmission method Access method Data transfer speed Maximum segment length Maximum number of nodes/segment Intel 82559 3 kB each for send and receive ISO8802-3 100BASE-TX/10BASE-T Twisted pair cable *1 (100 Mbps: Category 5, 10 Mbps: Categories 3 to 5) Base band C[...]

63 51 15 10 6 11 ■ Connector specifications The pin arrangement and signal names of each connector are as follows: ● CRT connector Pin no. Signal name Direction Description 1 TD+ Output Send data+ 2 TD- Output Send data- 3 RD+ Input Receive data+ 4 NC – Not connected 5 NC – Not connected 6 RD- Input Receive data- 7 NC – Not connected 8 NC[...]

64 Pin no. Signal name Direction Description 1 CD Input Carrier detection 2 RD Input Receive data 3 TD Output Send data 4 DTR Output Data terminal ready 5 GND – Ground 6 DSR Input Data set ready 7 RTS Output Send request 8 CTS Input Send enabled 9 RI Input Ring indication Pin no. Signal name Direction Description 1 STROBE Input/output Strobe 2 DA[...]

65 ● USB connector (SeriesA) Pin no. Signal name Direction Description 1 VCC – Cable, power supply 2 -DATA Input/output - data signal 3 +DATA Input/output + data signal 4 GND – Cable, ground 1234 ● Keyboard connector Pin no. Signal name Direction Description 1 DATA Input/output Data 2 NC – Not connected 3 GND – Ground 4 VCC – Power su[...]

66 How to clean the PC is explained as follows: Electric shock W ARNING ● To prevent electric shock, before cleaning the PC, switch off the PC and all connected units and unplug all power cords. ■ Cleaning the PC main unit - Wipe the PC main unit with a soft dry cloth. If necessary use a damp cloth but do not permit moisture to come into contac[...]

67 2 Remove the ball and clean with water. Reverse the mouse to remove the ball, then clean the ball with water. 3 Clean the inside of the mouse. Wipe the inside of the mouse, the rollers, and the back cover with a damp cloth. 4 Attach the ball and the back cover. After drying the ball and the inside of the mouse, attach the ball and back cover. ?[...]

68 ■ Peripheral devices and cables When peripheral devices or cables are connected to the PC, use Fujitsu-supplied devices and cables, as some non-Fujitsu devices and cables may not be connectable. ■ Note on using the display The vertical and horizontal lines displayed by a CAD application may appear different in width depending on the setting [...]

69 Windows 98/2000 1 Set the resolution to 640 x 480 (before replacement of the display). 2 Set the refresh rate to the "adapter default." 3 Terminate Windows and turn off the PC power, then replace the display. If there is no screen display or no display at some resolutoion after the display is replaced without performing the above setti[...]

70 ■ Wake up On LAN When "Wake-up from LAN" under "Automatic wake-up" of the power save menu in the BIOS Setup is set to "Enable," the PC power can be tuned on via a LAN(WOL: Wake up On LAN). To use this function , always turn on the PC power once after the power cable is connected. The function may not operate norma[...]

71 ■ CD-ROM drive If a CD-ROM cleaning disk sold separately is used for cleaning, the lens may not be clean. Do not use a CD-ROM cleaning disk. ■ Intel ® processor serial number Each Intel ® Pentium ® III processor contains a serial number that can be read electrically. The processor serial number can be used for information management, reso[...]

72 Fujitsu PC (Asia) Pte Ltd 200 Pandan Loop #05-03 Pantech 21 The Computer Centre Singapore 128388 Tel: 65-776 0688 Fax: 65-776 0788 Fujitsu PC (Asia) Pte Ltd (Malaysia Branch) 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia Tel: 603-253 3997 Fax: 603-253 4245 Website : www.fujitsu-pc-asia.com[...]