Fujitsu RX900 S1 manuale d’uso

Maintenance Manual - English PRIMERGY RX900 S1 Server Maint enance M anual Edition August 2010[...]

Comments … Suggestions … Corrections … The User Documentation Depar tment would lik e to know y our opinion of this manual. Y our f eedback helps us optimize our documentation to suit y our individual needs. F eel free to se nd us your comments by e-mail to manuals@ts.fujit su.com . Certified documentation according to DIN EN ISO 9 001:2008 T[...]

RX900 S1 Maintenance Manual 3 Before reading this manual For your safety This manual c ontains important information for s afely and correctly using this product. Carefully read the manual bef ore using this product. P a y par ticular attention to the accompan ying manual "Saf ety Notes and Regulations" and ensure these saf ety notes are [...]

4 Maintenance Manual RX900 S1 These uses include control of n uclear reactions in nuclear power plants , automatic airplane flight control, air traffic control, traffic control in mas s transport systems, medical de vices for lif e suppor t, and missile guidance control in weapons systems (hereafter , "high saf ety use"). Cus tomers shoul[...]

RX900 S1 Maintenance Manual 5 Only f or the Japan ese market: I Although described in this manual, some secti ons do not apply to the Japanes e market. These options and routines include: – CSS (Customer Sel f Ser vice) – USB Flash Module (UFM) – Replacing the lithium battery[...]

6 Maintenance Manual RX900 S1[...]

RX900 S1 Maintenance Manual 7 Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1.1 Where to find which information? . . . . . . . . . . . . . . . 20 1.1.1 Documents you need at hand . . . . . . . . . . . . . . . . . . 21 1.1.2 Accessing PRIMERGY documentation . . . . . . . . . . . . . 24 1.2 Notational con ventions .[...]

8 Maintenance Manual RX900 S1 Contents 4.9 Closing the rack door . . . . . . . . . . . . . . . . . . . . . . 51 5 P ower supply . . . . . . . . . . . . . . . . . . . . . . . . . . 53 5.1 Installing a hot-p lug P ower Supply Unit (PSU) . . . . . . . . 54 5.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 54 5.1.2 Star ting the [...]

RX900 S1 Maintenance Manual 9 Contents 5.4.17 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 77 6 Hard disk and solid state drives . . . . . . . . . . . . . . . . 79 6.1 Installing the HDD/SSD module . . . . . . . . . . . . . . . . 80 6.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 80 6.1.2 Star ting the [...]

10 Maintenance Manual RX900 S1 Contents 7 Fan modules . . . . . . . . . . . . . . . . . . . . . . . . . . 101 7.1 Replacing a defective fan module . . . . . . . . . . . . . . 102 7.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 102 7.1.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . 102 7.1.3 Opening the f[...]

RX900 S1 Maintenance Manual 11 Contents 8.5.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . . 133 8.5.3 Deactivati ng the ex pans ion card . . . . . . . . . . . . . . . . . 133 8.5.4 Pulling the e xpansion card out of the slot . . . . . . . . . . . . 134 8.5.5 Removing the e xpansion card from the removal tool . . . . . . 135 8[...]

12 Maintenance Manual RX900 S1 Contents 8.9.5 Inser ting the exp ansion card in the slot . . . . . . . . . . . . . 161 8.9.6 Installing the PCI Riser (if applicab le) . . . . . . . . . . . . . . 162 8.9.7 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 162 8.10 Replacing the Modular RAID controller . . . . . . . . . . . 163 8.10.1[...]

RX900 S1 Maintenance Manual 13 Contents 9.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 188 9.2.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . . 188 9.2.3 Identifying a f ault on the CPUMEMR . . . . . . . . . . . . . . 189 9.2.4 Removing the CPUMEM R . . . . . . . . . . . . . . . . . . . . 190 9.2.5 Re[...]

14 Maintenance Manual RX900 S1 Contents 10.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 215 10.3.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . 215 10.3.3 Removing the heat s ink . . . . . . . . . . . . . . . . . . . . . 216 10.3.4 Applying the thermal paste . . . . . . . . . . . . . . . . . . . 217 10.[...]

RX900 S1 Maintenance Manual 15 Contents 12.4 Replacing the I/O board . . . . . . . . . . . . . . . . . . . . 242 12.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 242 12.4.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . . 242 12.4.3 Removing the PCI Riser . . . . . . . . . . . . . . . . . . . . . 243 12.[...]

16 Maintenance Manual RX900 S1 Contents 14.3.3 Removing the UFM . . . . . . . . . . . . . . . . . . . . . . . 268 14.3.4 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 269 14.4 Installing the TPM . . . . . . . . . . . . . . . . . . . . . . . 270 14.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 270 14.4.2 St[...]

RX900 S1 Maintenance Manual 17 Contents 15.1.9 Completing the task . . . . . . . . . . . . . . . . . . . . . . . 300 15.2 Replacing the cont ro l panel cable . . . . . . . . . . . . . . . 301 15.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 301 15.2.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . . 302 [...]

18 Maintenance Manual RX900 S1 Contents 15.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 333 15.5.2 Star ting the task . . . . . . . . . . . . . . . . . . . . . . . . 334 15.5.3 Sliding the local serv ice displa y outward . . . . . . . . . . . . 335 15.5.4 Disconnecting the cab les . . . . . . . . . . . . . . . . . . . . 336 [...]

RX900 S1 Maintenance Manual 19 1 Intr oduction This Maintenance man ual provides procedures fo r : ● Replacing f aulty units to get t he system bac k to normal operation. ● Expanding the se r ver configur ation by using opti onal hardware components av ailable within the sam e release to meet new requirements . ● Upgrading the server b y repl[...]

20 Maintenance Manual RX900 S1 Introduction 1.1 Where to find whic h inf ormation ? While the Maintenance man ual focuses on maintenance proc edures to bring the system bac k to normal operation, individual manuals pro vide detailed back ground inf or mation on the board lay out, indicators, or BIOS Setup . Other documentation such as service foil [...]

RX900 S1 Maintenance Manual 21 Introductio n 1.1.1 Documents you need at hand In the maintenance procedures , you will find ref erences to other documents f or inf or mation that does not s uit into individual procedure steps . So please check which of these documents y ou need to ha ve at hand when y ou leav e f or maintaining a server . Document [...]

22 Maintenance Manual RX900 S1 Introduction Hardware poster The hardware poster summarizes inf or mation such as rack installation, power supply , HDD modules, and indicators . Illustrated spares catalog In the e vent of errors, the ServerVie w Operations Manager ref ers you directly to the aff ected component and its order inf or mation in the Ill[...]

RX900 S1 Maintenance Manual 23 Introductio n Additional documentation i s av ailable on more specific topi cs. Please chec k which of these documents y ou need for individual tasks : ● Documentation f or the boards and dr ives ● Information files in y our operating system ● Manual f or the monitor ● Operating system doc umentation ● "[...]

24 Maintenance Manual RX900 S1 Introduction 1.1.2 Acces sing PRIMERGY documentation Y ou ha ve the f ollowing options to access PRIMERGY docum entation: ● Open the ServerVie w Suite D VD 2 which is par t of the ServerVie w Suite supplied with e very ser ver . The latest v ersion of the ServerVie w Suite D VD 2 is av ailab l e by using the f ollow[...]

RX900 S1 Maintenance Manual 25 2 Bef ore y ou st ar t Bef ore you star t to replace or install hardware components in the RX900 S 1 server , please proceed as fol l ows: Ê Carefully read the saf ety instr uctions in the chapter "Safety instr uctions" on page 31 . Ê Make s ure that all necessary manuals are a vailab l e by us ing the lis[...]

26 Maintenance Manual RX900 S1 Before y ou star t Replacing a faulty compo nent The global error indicator on the front and on the rear side of the server indicates that a hardw are components needs to be replaced. F or information on the control elements and indicators of your ser ver see "PRIMERGY RX900 S1 Server - Operating manual". If[...]

RX900 S1 Maintenance Manual 27 Before you start 2.1 Cl assification of proce d ures The comple xity of procedures to instal l or replace hardware components v aries a lot. Three categories indicate the degree of difficulty and the profile of qualification needed to perf or m a task. W ar nings help you to assess the consequences f or performing pro[...]

28 Maintenance Manual RX900 S1 Before y ou star t Authorized personnel Authoriz ed s pecialist personnel can carry out replacement tasks for integral ser ver components . Please ask you local Fujitsu service center for more det ailed inf or mation. V CA UTION! Procedures indicated as "A uthorized personnel only“ must be done by Fuj itsu ser [...]

RX900 S1 Maintenance Manual 29 Before you start 2.2 Li st of required too ls Bef ore leaving f or the s er ver , please make sure that y ou hav e Phillips head screw driv ers of the size Ph0, Ph1, and Ph2 with y ou. Y ou will find a list of required tools at the beginning of each procedure . Ta b l e 2 l ists all a vailab le screws in the RX90 0 S1[...]

30 Maintenance Manual RX900 S1 Before y ou star t Slimli ne Optica l driv e M2.0 Phillips Ph0 TPM sc rew -- P hill ips P h0 UFM nylon screw -- Phillips Ph1 USB module screw -- Phillips Ph1 Usage T ype Figure Head T ool / Bit insert T able 2: List of scre ws for the RX900 S1[...]

RX900 S1 Maintenance Manual 31 3 Safety instructions I The f ollowing saf ety instructions are also provided i n the manual "Saf ety Notes and Regulations". This de v ice meets the relev ant safety regulations f or IT equipment. If you hav e any questions about whether y ou can install the ser ver in the i ntended envi ronment, please con[...]

32 Maintenance Manual RX900 S1 Safety instructions Installation and operation V CA UTION! ● If the de vi ce is integ rated in an instal lation that receiv es power from an industrial (publi c) pow er supply network with the IEC309 connector , the (public) po wer s upply protection must comply with the requirements f or the non-industr ial (publi [...]

RX900 S1 Maintenance Manual 33 Safety instructions V CA UTION! ● Make su re that no objects (such as bracelets or paper clips) f all into or liquids spill i nto the dev ice (risc of electric shock or shor t circuit). ● In emergencies (e .g. damaged casing, controls or cab les, penetr ation of liquids or f oreign matter), switch off the devi ce [...]

34 Maintenance Manual RX900 S1 Safety instructions Batteries V CA UTION! ● Incorrect replacement of batteries may result in a risk of ex plosion. The batteries may only be replaced with i dentical batteri es or with a type recommended b y the manuf acturer (see the T ec hnical Manual for the s ystem board). ● Replace the lithium batter y on the[...]

RX900 S1 Maintenance Manual 35 Safety instructions V CA UTION! ● Only use CDs/D VDs that are in perf ect condition in your ser v er's CD/D VD drive, in order to prev ent data loss, equipment damage and injury . ● Check each CD/D VD f or damage, cr acks , br eakages etc. bef ore inser ting it in the drive . Note that any additi onal labels [...]

36 Maintenance Manual RX900 S1 Safety instructions Modules with electrostatic-sensitive comp onents Systems and components that might be damaged b y electrostatic discharge (ESD) are marked with the f ollowing label : Figure 2: ESD label When y ou handle components fitted with ESDs, you must observe the fol l owing points under all circumstances: ?[...]

RX900 S1 Maintenance Manual 37 4 Ba sic procedur es This section introduces all bas ic procedures that might be needed to start or complete a replacement or e xpansion task. The individual basic procedures applicab le f o r a replacement or e x pansion task are indicated in the procedure related to this task. 4.1 Usi ng diagnostics information Use [...]

38 Maintenance Manual RX900 S1 Basic procedures If the e vent is still acute after a pow er failure, the i ndicator is activ ated after the restar t. The indicator also lights up in standb y mode. Y ou can fi nd more details on the indicated errors in t he System Ev ent Log (SEL), on the Ser verVie w Local Ser vice Panel, on the ServerVie w Local S[...]

RX900 S1 Maintenance Manual 39 Basic procedures 4.1.2 Locate the faulty component by PRIMERGY diagnostics indicators If the system has been powered off to replace a non-hot-plug unit, a system of PRIMERGY diagnostics indicators guides y ou to the faulty component . F or the RX900 S1, it is possib le to tur n on the local diagnostics indicators f or[...]

40 Maintenance Manual RX900 S1 Basic procedures Ê Press the CSS button l ocated on the PCI Riser (PCIR). Ê The PRIMERGY diagnostics indicator of the f aulty unit will light up . F or inf or mation on the control elements and indicators of y our ser v er see "PRIMERGY RX900 S1 Server - Operati ng manual" and "Baseboard D3081, CPUMEM[...]

RX900 S1 Maintenance Manual 41 Basic procedures 4.3 Shutting down t h e server V CA UTION! F ollow the s afety instructions in the "Saf ety instructions" on page 31 . I This step is only applicab le to replace or expand non-hot plug components. Ê T erminate all applications and shut do wn the ser ver correctly . Ê If your operati ng sys[...]

42 Maintenance Manual RX900 S1 Basic procedures 4.4 S liding the ser ver ou t of the rack V CA UTION! ● Use the anti-tilt plate to pr e vent the rac k from tipping when installing the rack . Pulling the ser v er out of the rack without hav i ng installed the anti-tilt plate ma y cause the rack to tip o ver . ● Be careful not to pinch fingers or[...]

RX900 S1 Maintenance Manual 43 Basic procedures Ê Pull the server carefully out of the rack as f ar as possible (2). V CA UTION! Do not use the pulled-out server as a surfac e on which to put things or as a work surface , and s trictly av oid leaning on or against it. Removing the server from the rack (if applicable) V CA UTION! Due to the heavy w[...]

44 Maintenance Manual RX900 S1 Basic procedures 4.5 Opening the server V CA UTION! ● Only f or non-hot plug components: Bef ore removing or installing co v ers, turn off the ser ver , all peripheral dev i ces, and any other connected de vices. Also unplug all po wer cabl es from the outlet. F ailure to do so can cause electric shock. ● The hous[...]

RX900 S1 Maintenance Manual 45 Basic procedures Figure 5: F ront cover (1), f an cover (2), and rear cover ( 3) 4.5.1 Remo ving the fr ont cover Figure 6: Removing t he front cov er / 0 1 / 0[...]

46 Maintenance Manual RX900 S1 Basic procedures Ê Loosen the captive s c rew on the cov er (see circle). Ê Push the front cov er back by appro ximately 1 cm. Ê Remov e the front cov er by lifting i t upward. 4.5.2 Remo ving the r ear co ver Figure 7: Removing the rear cover Ê Loosen the captive s c rews on the rear cov er (see circle) . Ê Push[...]

RX900 S1 Maintenance Manual 47 Basic procedures 4.6 Closing the server V CA UTION! ● Before atta ching the cov ers, mak e sure no unnecessar y par ts or tools are left inside the server . ● The housing cov ers must be replaced as soon as possible f or pur poses of cooling, to comply with EMC regulations (regulations regarding electromagnetic co[...]

48 Maintenance Manual RX900 S1 Basic procedures Ê Place the front cov er onto the server such that there is approx imately 1 cm distance to the front. Ê Push the front cov er as far as possib l e in the direction of the arrow . Ê F asten the captive scre w on the cover (see circle). 4.6.2 Instal ling the re ar cover Figure 9: Installing the rear[...]

RX900 S1 Maintenance Manual 49 Basic procedures 4.7 Mountin g the server in the rac k Inserting t he server (if app licable) Figure 10: Inser ting t he ser ver Ê Pull the middle par ts of the r ails out of the rac k completel y until the y click into place (1). I The middle par ts of the rails m ust clic k into place so that they can no longer be [...]

50 Maintenance Manual RX900 S1 Basic procedures Ê Inser t the inner par ts of the rails that are mounted on the ser ver into the protruding middle par ts until the rails engage (2). Ê Release the loc king mechanism of both rails (3). – Left side oft the server: Push upwards – Right side of the ser v er : Push downw ards Ê Lower the li fter p[...]

RX900 S1 Maintenance Manual 51 Basic procedures 4.8 Bringing the server back to operation V CA UTION! ● Before turning on the server , make sure the co vers are closed. ● F ollow t he saf ety i nstructi ons in chapter "Safety instructions" on page 31 . I This step is only applicab le to replace or expand non-hot plug components. Ê Co[...]

52 Maintenance Manual RX900 S1 Basic procedures[...]

RX900 S1 Maintenance Manual 53 5 P ower suppl y V CA UTION! The ser ver supports a mains voltage in the r ange of 200 - 240 V . Y ou ma y only operate the server if its rated v oltage range corresponds to the local mains voltag e. I Phase redundancy is possib l e in regions, where a single phase pro v ides 200 - 240V ; in other regions with lower s[...]

54 Maintenance Manual RX900 S1 P ower supp ly 5.1 In stalling a hot-plu g P ower Supply Unit (PSU) 5.1.1 Required tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) ● Installing the pow er s upply unit: tool-less 5.1.2 Star t ing t he ta sk Ê P erf or m the f ollowing procedures: 1. Open the rear door of [...]

RX900 S1 Maintenance Manual 55 Power supply Ê Press the two plastic clips together as indicated b y the arrows and remov e the dummy modul e. V CA UTION! K eep the dummy module f or future us e. If the po wer supply unit is remov ed and not replaced with a new unit, the dummy module must be reinstalled due to cool ing, to comply with applicab le E[...]

56 Maintenance Manual RX900 S1 P ower supp ly 5.1.5 Connecting the power cord Figure 13: Connecting the po wer cord and the f errite core Ê Thread the cable through the cab le strap . Ê Pull the cable s trap tight to secure the power cord. Ê Connect the newl y installed pow er supply unit to the mains. Ê Check whether the power supply unit work[...]

RX900 S1 Maintenance Manual 57 Power supply Figure 14: Indicators on the power supply unit 5.1.6 Complet ing the ta sk Ê P erform the f ollowing procedures to complete the task: 1. Close the rear door of the rac k , see "Closing the rack door" on page 51 5.2 Repl acing a ho t-plug power supply unit V CA UTION! When replacing a non-defect[...]

58 Maintenance Manual RX900 S1 P ower supp ly 5.2.2 Star t ing t he ta sk Ê P erf or m the f ollowing procedures: 1. Open the rear door of the rac k , see "Opening the r ack door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. Only when replacing a non-defective hot-plug po wer supply unit in a non-redundant configura[...]

RX900 S1 Maintenance Manual 59 Power supply 5.2.4 Reinstalling the PSU Ê Inser t the new po wer supply unit i nto the ba y as described in "Installing a hot-plug P ower Supply Unit (PSU)" on page 5 4 . I Make sure that the po wer supply unit engages correctly in the mounting location and is loc ked in pos ition. This is the only w ay to [...]

60 Maintenance Manual RX900 S1 P ower supp ly 5.3.3 Remo ving the power suppl y unit Figure 16: Unlocking and removing the power supply unit Ê Remov e the power cord from the cable strap . Y ou can loosen the cabl e strap b y opening the small loc king le ver . Ê Remov e the power cord from the installed po wer supply unit. Ê Press the green rel[...]

RX900 S1 Maintenance Manual 61 Power supply 5.3.4 Installing a dumm y module I Dummy modules protect free bays agai nst environme ntal impact. Figure 17: Installing a dum my module in a PSU bay Ê Press the two plastic clips together as indicated b y the arrows and install the dummy modul e. 5.3.5 Complet ing the ta sk Ê P erform the f ollowing pr[...]

62 Maintenance Manual RX900 S1 P ower supp ly 5.4 Replacing the power distrib ution b oar d 5.4.1 Required tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the pow er distribution board: – Phillips Ph2 sc rew driver 5.4.2 Star t ing t he ta sk Ê P erf or m th[...]

RX900 S1 Maintenance Manual 63 Power supply 7. Remov e all CPUMEMRs, see "Remov ing the CPUMEMR" on page 190 I Before remo ving the CPUMEMRs, tak e a note on the installation slot number f or each CPUMEMR. Make sure that y ou r einstall the CPUMEMR in the slot it was located before the replacement. 8. Remov e all expansion c ards and dumm[...]

64 Maintenance Manual RX900 S1 P ower supp ly 5.4.4 Disconnecting the cables Figure 19: Disconnectin g the cables from the baseboard Ê Disconnect the f ollowing cab les from the bas eboard: – SAS backpl ane cable (1) – Signalling cab le (2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5) [...]

RX900 S1 Maintenance Manual 65 Power supply 5.4.5 Remo ving the fan cage Figure 20: Removing the fan cage Ê Loosen the captive s c rews (1). Ê Lift the f an cage out of the chassis (2) . / / 0[...]

66 Maintenance Manual RX900 S1 P ower supp ly 5.4.6 Remo ving the CPUMEMR guide Figure 21: Removing the CPUMEMR guide Ê Loosen the captiv e scre ws of the CPUMEMR guide (1). Ê Lift the CPUMEMR guide out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 67 Power supply 5.4.7 Remo ving the air guide Figure 22: Removing the air g uide Ê Loosen the captive s c rews (1). Ê Lift the air guide out of the chassis (2). / / 0[...]

68 Maintenance Manual RX900 S1 P ower supp ly 5.4.8 Remo ving the base boar d Figure 23: Removing the baseboard Ê Loosen the captiv e screws (1). Ê Slide the baseboard appro ximately 1 cm in the direction of the arrow (2). V CA UTION! Make s ure that you ha ve remo ved al l pow er supply units bef or e removing the baseboard. Otherwise , the powe[...]

RX900 S1 Maintenance Manual 69 Power supply 5.4.9 Remo ving the power distrib ution board Figure 24: Removing the power distr ibution board Ê Open the cable clamps (1). Ê Disconnect the pow er c ables from the baseboard (2). Ê Loosen the captive s c rews (3). Ê Remov e the power distribution board from the bas eboard. / / 0 0 1 1 2[...]

70 Maintenance Manual RX900 S1 P ower supp ly Figure 25: Disconnect ing the power cables Ê Disconnect the f ollowing cab les from the pow er dis tribution board: – P ower cab le of the optical drive (1, 2) – P ower cable for the SAS bac kplane (3) – P ower distributi on cables (4) / / 0 1 2 2[...]

RX900 S1 Maintenance Manual 71 Power supply 5.4.10 Installing th e po wer distribution boar d Figure 26: Connecting the power cables Ê Connect the f ollowing cab l es to the pow er distribution board: – P ower distributi on cables (1) – P ower cab le for the SAS bac kplane (2) – P ower cab l e of the optical drive (3, 4) 1 2 / / 0 1[...]

72 Maintenance Manual RX900 S1 P ower supp ly Figure 27: Installing the po wer distr ibution board Ê Inser t the power distribution board in the bas eboard (1). Ê Connect the pow er cables to th e baseboard (2). Ê F asten the captive scre ws (3). Ê Close the cable cl amps (4). 5.4.11 Inserting the baseboar d Figure 28: Inser ting the baseboard [...]

RX900 S1 Maintenance Manual 73 Power supply Ê Carefully lo wer the baseboard in the chassis b y using the handle (1). Ê Slide the baseboard in the direction of the arro w ( 2) until it clic ks into place. Ê F asten the captiv e screws (3). V CA UTION! Ensure not to damage the EMI springs to comply with appl icabl e EMC regulations and satisfy co[...]

74 Maintenance Manual RX900 S1 P ower supp ly 5.4.13 Inser ting the CPUMEMR guide Figure 30: Inserting the CPUMEMR guide Ê Inser t the CPUMEMR guide in the installation s lot (1). Ê F asten the captiv e screws of the CPUMEMR guid e ( 2). 0 0 /[...]

RX900 S1 Maintenance Manual 75 Power supply 5.4.14 Inserting the fan ca ge Figure 31: Inser ting t he fan cage Ê Inser t the f an cage in the mounting ba y (1). Ê F asten the captiv e screws (2). / 0 0[...]

76 Maintenance Manual RX900 S1 P ower supp ly 5.4.15 Connect ing the ca bles to the baseboard Figure 32: Connecting the cab l es to the baseboard Ê Connect the f ollowing cables to the baseboard: – SAS backpl ane cable (1) – Signalling cab le (2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cabl[...]

RX900 S1 Maintenance Manual 77 Power supply 5.4. 16 Sliding the l ocal servi ce displ ay inward Figure 33: Sliding the local s er vice display inward Ê Slide the local ser vice displa y inwa rd until it clic ks into place. 5.4.17 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. Install the BBU holder , see "E[...]

78 Maintenance Manual RX900 S1 P ower supp ly 6. "Closing the server" on page 47 7. "Mounting the server in the rac k" on page 49 8. "Bringing the ser ver bac k to operation" on page 51 9. "Closing the rac k door" on page 51 Ê V er ify the settings on the baseboard, see the "Basebo ar d D3081, CPUMEMR D[...]

RX900 S1 Maintenance Manual 79 6 Har d disk and so lid stat e driv es The hard disk drives whic h can be or dered f or the PRIMERGY RX900 S1 are supplied already mounted in an i ns tallati on frame so that def ective h ar d disk drives c an be replaced and ne w hard disk drives can be added during operation. The hard disk drive/soli d state drive a[...]

80 Maintenance Manual RX900 S1 Hard disk and solid state drives ● Rough handling of hard disk units can damage the st ored data. T o cope with any une xpected problem s, alwa ys back up impor tant data. When bac k ing up data to another hard disk drive , you should mak e back ups on a file or par tition basis . ● Be careful not to hit the hard [...]

RX900 S1 Maintenance Manual 81 Hard disk and solid state drives 6.1.3 Remo ving the dummy module Dummy modules protect free ba ys against environmental impact. Remo ve the dummy modul e before ins talling an additional HDD/SSD module. Figure 34: Removing/installing the 2.5-inch dum my module Ê Press both tabs on the dummy module together until the[...]

82 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.1.4 Unlocking the HDD/SSD module Figure 35: Unloc king the 2.5-inch HDD/SSD module Ê Release the loc king mechanism as f ollows: 1. Press the two g reen tabs of the loc king le v er together (1). 2. Push the handle of the HDD/SSD module fully in the di rection of the arrow (2). The [...]

RX900 S1 Maintenance Manual 83 Hard disk and solid state drives 6.1.5 Inser ting the HDD/SSD module Figure 36: Installing the 2. 5-inch HDD/SSD module Ê Carefully push the HDD/SSD module into the empty ba y (1) until it stops. Ê Push the handle c ompletely (2) in the direction of the arrow until the loc king mechanism engages . 6.1.6 Complet ing [...]

84 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.2 Replacing the HDD/SSD module V CA UTION! ● Only remov e an HDD/SSD module dur ing operation if the drive is not currently being accessed. Observe the indicato r s f or the corresponding HDD/SSD modules, s ee "PRIMERGY RX900 S1 Server - Operating manual". ● Under no ci[...]

RX900 S1 Maintenance Manual 85 Hard disk and solid state drives 6.2.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. "Locate the f aulty component by PRIMERGY diagnos tics indicators" on page 39 Only applicable f o r removin[...]

86 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.2.4 Removing the HDD/SSD module Ê Pull the HDD/SSD module out a f ew centimeters . Ê W ait f or at least 60 seconds. I This period is necessar y for the RAID controller to recognize that an HDD/SSD module has been remov ed and for the hard disk driv e to come to a stop . Ê Pull th[...]

RX900 S1 Maintenance Manual 87 Hard disk and solid state drives 6.3.3 Unlocking the HDD/SSD module Figure 38: Unlocking the 2.5-inch HDD/SSD module Ê Release the loc king mechanism as fo llows: 1. Press the two green tabs of the loc king lev er together (1). 2. Push the handle of the HDD/SSD module fully in the direction of the arrow (2). The HDD/[...]

88 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.3.5 Installing the dummy module T o install a d ummy module , follo w the procedure for "Removing the dumm y module" on page 81 in re verse order . 6.3.6 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Closing the rac k door" [...]

RX900 S1 Maintenance Manual 89 Hard disk and solid state drives 6.4 Replacing the SAS backplane 6.4.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the SAS bac kplane: – Phillips Ph2 scre w dr iver 6.4.2 Sta r ting the task Ê P erform the f ollowin[...]

90 Maintenance Manual RX900 S1 Hard disk and solid state drives 6. Remov e all CPUMEMRs, see "Remo ving the CPUMEMR" on page 190 I Bef or e remo v ing the CPUMEMRs, take a note on the installati on slot number f or each CPUMEMR. Make sure that you re install the CPUMEMR in the slot it was located before the SAS bac kplane replacement. 7. [...]

RX900 S1 Maintenance Manual 91 Hard disk and solid state drives 6.4.4 Disc onnecting the cables Figure 40: Disconnecting t he cables from the baseboard Ê Disconnect the f ollowing cables from the baseboard: – SAS bac kplane cable (1) – Signalling cabl e ( 2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F r[...]

92 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.4.5 Sliding the optical drive outward Figure 41: Sliding the opt ica l drive outw ard Ê Use the handle (A) to unloc k the optical driv e. Ê Slide the optica l drive outw ar d a f ew centimeters so that you ha ve free access to the SAS bac kplane (see circ les). C A[...]

RX900 S1 Maintenance Manual 93 Hard disk and solid state drives 6.4.6 Remo ving the air guide Figure 42: Removing the air g uide Ê Loosen the captive s c rews (1). Ê Lift the air guide out of the chassis (2). / / 0[...]

94 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.4.7 Remo ving the SAS bac kplane Figure 43: Removing the SAS bac kplane Ê Loosen the captiv e screw (see circle) on the SAS bac kplane. Ê Remov e the SAS backplane b y pulling it straight upward. Do not ti lt it. 6.4.8 Installing the SAS backplane Figure 44: Installing the SAS bac [...]

RX900 S1 Maintenance Manual 95 Hard disk and solid state drives 6.4.9 Insta lling the air guide Figure 45: Installing the air guide Ê Place the air guide in th e chassis (1). Ê F asten the captiv e screws (2). 0 0 /[...]

96 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.4.10 Sliding the optical drive inwar d Figure 46: Sliding the opt ica l drive inw ard Ê Slide the optica l drive into the ba y until it clic k s into place .[...]

RX900 S1 Maintenance Manual 97 Hard disk and solid state drives 6.4.11 Connecting the cab les to the baseboard Figure 47: Connecting the cables to the baseb oard Ê Connect the f ollowing cab l es to the baseboard: – SAS bac kplane cable (1) – Signalling cabl e ( 2) and power cab le (3) to the optical drive – F ront video connector cable (4) [...]

98 Maintenance Manual RX900 S1 Hard disk and solid state drives 6.4.12 Sliding the l ocal service di splay inwar d Figure 48: Sliding the local s ervice display inward Ê Slide the local service display i nward until it click s into place .[...]

RX900 S1 Maintenance Manual 99 Hard disk and solid state drives 6.4.13 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. Inser t all HDD/SSD modules, s ee "Unloc king the HDD/SSD m odule" on page 82 and "Inser ting the HDD/SSD module" on page 83 . I Make sure that y ou reinstall the module in the[...]

100 Maintenance Manual RX900 S1 Hard disk and solid state drives[...]

RX900 S1 Maintenance Manual 101 7 F an modules The server is supplied with f our hot-plug fan modules i n a 3+1 redundant configuration. In other words , if one of t he four f an modules fails , the system will operate without an y probl em. V CA UTION! ● Do not disassembl e the pow er supply unit. Doing so ma y cause electric shock. ● Do not d[...]

102 Maintenance Manual RX900 S1 F an modul es 7.1 Replacing a defective f an module 7.1.1 Required tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) ● Replacing the f an module: tool-less 7.1.2 Star t ing t he ta sk Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 [...]

RX900 S1 Maintenance Manual 103 Fan m odules 7.1.4 Replacing the defective fan module Figure 50: Identifying and rem oving a defectiv e f an module Ê Identify the defe ctiv e fan module . T he indicator of the defectiv e fan lights up Orange, s ee c ircle in figure 50 . Ê Hav e the new f an module ready for the installation. V CA UTION! Nev er le[...]

104 Maintenance Manual RX900 S1 F an modul es 7.1.5 Closing th e fan cover Figure 51: Closing the f an cover Ê Press the handle in direction of the arro w and inser t the f an cov er into the front cov er . 7.1.6 Completing the task P erf or m the f ollowing procedures to complete the tas k : 1. "Mounting the server in the rac k" on page[...]

RX900 S1 Maintenance Manual 105 8 Expansion ca r ds and BBU I The number and location of a vailabl e PCIe slots depends on the CPUMEMR configuration. Mak e sure that the planned CPUMEMR configuration enab les you to use the PCIe slots needed f or the individual use case of the ser v er . F or detailed inf or mation on configuration rules and suppor[...]

106 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU F or inf or mation on the population order and the capability of the slots see "Baseboard D3081, CPUMEMR D3131, PCIR D3082 f or PRIMERGY RX900 S1 T echnical Man ual". I The RX900 S1 ser ver can be equipped with one Modular RAID controller and two SAS RAID co ntrollers but only f[...]

RX900 S1 Maintenance Manual 107 Expansion cards and BBU 8.1 Mo unting expansion card slot brackets This section provides G eneral instr uctions f or mounting slot brac kets as w ell as specific instructions f or the f ollowing e xpansion cards: ● "Network adapter D2735" on page 108 ● "Network adapter D2745" on page 110 ● &[...]

108 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.1.2 General inst ructions Figure 53: Mounting e xpans ion card slot brac kets Ê Place the controller on the mounting tabs on the slot brac ket (1). Ê Secure the slot brack et to the controller with two M3 x 4.5 mm screws . 8.1. 3 Netw ork ada pter D27 35 /[...]

RX900 S1 Maintenance Manual 109 Expansion cards and BBU Ê Place the controller on the mounting tabs on t he slot brack et (1). Ê Carefully shift the slot brack et towards the controller (2) until the plug shells engage with the cut-outs in the slot brack et connector panel (see circle). Ê Secure the slot brac ket to the controller with two M3 x [...]

110 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.1. 4 Netw ork ada pter D27 45 Ê Hinge the slot brac ket to the pl ug shell as shown (1). Ê F old the slot brac ket to wards the controller until the threaded mounting tab is aligned with the scre w hole on the controller (2).[...]

RX900 S1 Maintenance Manual 111 Expansion cards and BBU Ê Secure the slot brac ket to the controller with one M3 x 4.5 mm scre w . Assemb led network adapter D2745.[...]

112 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.1. 5 Netw ork ada pter D27 55 Ê Place the controller on the mounting tabs on the slot brac ket (1). Ê Carefully shift the slot br ack et towards the controller until the plug shells engage with the cut-outs in the slot br ack et connector panel (2) . Ê Ensure that the ESD springs on [...]

RX900 S1 Maintenance Manual 113 Expansion cards and BBU Ê Secure the slot brac ket to the controller with two M3 x 4.5 mm scre ws. Assemb led network adapter D2755.[...]

114 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.2 Insta llin g SFP + tr ans ceiv er m odule s F or Fiber Channel ov er Ether net (FCoE) configurations, the ethernet ser ver adapter is equipped with one or tw o SFP+ (small f or m-factor pluggab le) transceiv er modules. 8.2.1 Required tools ● Installing SFP+ tr ansceive r modules: t[...]

RX900 S1 Maintenance Manual 115 Expansion cards and BBU 8.2.2 Preparing the SFP+ transceiver module Figure 54: Removing t he protective optical port plug Ê Remov e the SFP+ transceiver modul e from its protectiv e packaging. Ê Remov e the optical por t plug from the new / additi onal SFP+ transceiv er module. V CA UTION! – Alwa ys keep the prot[...]

116 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Figure 55: Unlatching the loc king bail Ê Carefully unlatch and f old down the locki ng bail on the SFP+ transceiv er module. 8.2.3 Inser ting the SFP+ transceiver module Figure 56: Inser ting the SFP+ transceiv er module[...]

RX900 S1 Maintenance Manual 117 Expansion cards and BBU Ê Inser t and slide the SFP+ transceiv er module into the socket connector as far as it will go . I If only one slot is equipped wi th a SFP+ transceiv er module, use the primar y r ight connector as shown. Figure 57: Latching the locking bail Ê Carefully f old up and latch the loc king bail[...]

118 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Figure 58: Attaching the protective optical port plug Ê If the SFP+ transceiv er module is not im mediately connected to an LC connector , attach the protectiv e optical por t plug to the transceiv er optical bores.[...]

RX900 S1 Maintenance Manual 119 Expansion cards and BBU 8.2.4 Installing the secondary SFP+ transceiver module Figure 59: Installing the secondary SFP+ transceiver module Ê If applicab le, ins tall the secondar y SFP+ transceiv er module accordingly .[...]

120 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.3 Replacing SFP+ transcei ver modules F or Fiber Channel ov er Ether net (FCoE) configurations, the ethernet ser ver adapter is equipped with one or tw o SFP+ (small f or m-factor pluggab le) transceiv er modules. 8.3.1 Required tools ● Removing S FP+ transceiv er modules: tool-less A[...]

RX900 S1 Maintenance Manual 121 Expansion cards and BBU 8.3.2 Remo ving an SFP+ transceiver module Figure 60: Removing t he protective optical port plug Ê If present, remov e the protective optical por t plug from the SFP+ trans ceiv er module. V CA UTION! Sav e the protective port plug for future use .[...]

122 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Figure 61: Unlatching the loc king bail Ê Carefully unlatch and f old down the locki ng bail on the SFP+ transceiv er module to eject the tra nsceiver from the soc ket connector .[...]

RX900 S1 Maintenance Manual 123 Expansion cards and BBU Figure 62: Removing t he SFP+ transceiver Ê Pull the SFP+ transc eiv er module out of its soc k et c onnector . Ê Reattach the protectiv e optical por t plug to the transceiv er optical bores. I Place the remov ed SFP+ transceiv er module in an antistatic bag or other protectiv e environment[...]

124 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.4 In stalling a hot-plu g expansion card V CA UTION! ● The actions described in this section ma y only be performed b y personnel with the appropr iate technical training. The de vice can be seriously damaged if it is opened withou t authorization or if repairs are attempted by untr a[...]

RX900 S1 Maintenance Manual 125 Expansion cards and BBU 8.4.2 Sta r ting the task I Read the accompanying documentati on supplied with the e xpansion card bef or e proceeding. Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Sliding the server out of the rac k" on page 42 3. "Removing the rea[...]

126 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Ê Open the slot to be fitted (1). Ê Remov e the slot lock b y pulling the green handle upward (2), pushing the plastic par t down (3) and lifting the slot loc k (4). Ê Pull the remo val tool out of the slot b y the handle (5). 8.4.4 Remo ving the r etaining pl ate Figure 64: Removing t[...]

RX900 S1 Maintenance Manual 127 Expansion cards and BBU 8.4.5 Remo ving the engaging hooks Figure 65: Removing t he engaging hooks Ê Push the green engaging hooks down in the direction of the arrows (1) until they di sengage from the remov al tool. Ê Remov e the engaging hooks (2) and keep them in a saf e place. 8.4.6 Inser ting an expansion car [...]

128 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Long expansion cards Figure 66: Inserting the expansion card in t he rem ov al tool Ê Inser t the e xpansion card in the slot of the remov al tool. Ê Inser t the green engagi ng hooks in the rods and push them do wn until they engage in the upper edge of the e xpansion card. I Make s ur[...]

RX900 S1 Maintenance Manual 129 Expansion cards and BBU Ê Inser t the e xpansion card in the remov al tool so that as recesses fit e xactly in the remo val tool (see c ircle) and fix the card with the engaging hook (1). Ê Inser t the other two green engaging hooks (2). Check the result of the installation for all expansion car ds Figure 68: P osi[...]

130 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.4.7 Inser ting the ex pans ion ca rd in the slot Figure 69: Inserting the expansion card in t he slot Ê Carefully inser t the removal tool together with the expansion card in the slot (1). Ê Inser t the slot lock (2) and relock the slot (3). Ê Close the hot-plug slot (4). Ê If appli[...]

RX900 S1 Maintenance Manual 131 Expansion cards and BBU 8.4.8 Act iva ting the ex pansion car d Ê Activ ate the ex pansion card using either the related PCI hot-plug software or by pressing the light-pipe s witch, see A in Figure 69 . The light-pipe s witch flashes green. The slot is in the enab le sequence. Ê W ait until the light-pipe s witch i[...]

132 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.5 Removing a hot-plug e x pansion car d V CA UTION! ● The actions described in this section ma y only be performed b y personnel with the appropr iate technical training. The de vice can be seriously damaged if it is opened withou t authorization or if repairs are attempted by untr ai[...]

RX900 S1 Maintenance Manual 133 Expansion cards and BBU 8.5.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Sliding the server out of the rac k" on page 42 3. "Removing the rear co ver" on page 46 8.5.3 Deactivating the expansion car d Ê Deactivate the expansion c[...]

134 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.5.4 Pulling the ex pansion car d out of the slot Figure 70: Pulling the expansion card out of t he slot Ê Open the slot containing the e xpansion card (1). Ê Remov e the slot lock b y pulling the green handle upward (2), pushing the plastic par t down (3) and lifting the slot loc k (4[...]

RX900 S1 Maintenance Manual 135 Expansion cards and BBU 8.5.5 Remo ving the e xp ansion car d from the remov al tool Figure 71: Removing the expansion card from the removal tool Ê Lift the green mo vable engaging hooks no more than appro x imately 1 mm until the e xpansion card is completely released. Ê T ake the e xpansion card out and put it as[...]

136 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.5.6 Remov ing the engaging hooks Figure 72: Removing t he engaging hooks Ê Push the green engaging hooks do wn in the direction of the arrows (1) until they di sengage from the remov al tool. Ê Remov e the engaging hooks (2) and keep them in a saf e place. // / 0 0 0[...]

RX900 S1 Maintenance Manual 137 Expansion cards and BBU 8.5.7 Inser ting a retaining plate in the remova l tool Figure 73: Inser ting t he retaining plate in the rem ov al tool Ê Inser t the retaining plate in the slot of the remov al tool. Ê Inser t the green engagi ng hooks in the rods and pus h them do wn until they engage in the upper edge of[...]

138 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.5.8 Inser ting the dumm y module in the slot Figure 74: Inserting the dummy module in the slot Ê Carefully inser t the remov al tool together with the dummy module i n the slot (1). Ê Inser t the slot lock (2) and relock the slot (3). Ê Close the hot-plug slot (4). 8.5.9 Completing t[...]

RX900 S1 Maintenance Manual 139 Expansion cards and BBU 8.6 Repl acing a hot-plug expansion car d V CA UTION! ● The actions described in this section ma y only be perf ormed by personnel with the appropriate technical t raining. The de vice can be seriously damaged if it is opened without authorization or if repairs are attempted by untrained per[...]

140 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.6.2 Star t ing t he ta sk I Read the accompan ying documentation supplied with the e xpansion card bef ore proceeding. Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. "Sliding the serv[...]

RX900 S1 Maintenance Manual 141 Expansion cards and BBU 8.6.4 Pulling the expansi on card out of the slot Figure 75: Pulling the expansion card out o f the slot Ê Open the slot containing the e xpansion card (1). Ê Remov e the slot lock b y pulling the gr een handle upw ard (2), pushing the plastic par t down (3) and lifting the slot loc k (4). ?[...]

142 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.6.5 Remo ving the e xpansion car d from the remo val tool Figure 76: Removing the e xpansion card from the remov a l tool Ê Lift the green mo vable engaging hooks no more than approxi mately 1 mm until the e xpansion card is completely released. Ê T ake the e xpansion card out and put[...]

RX900 S1 Maintenance Manual 143 Expansion cards and BBU 8.6.6 Remo ving the engaging hooks Figure 77: Removing t he engaging hooks Ê Push the green engaging hooks down in the direction of the arrows (1) until they di sengage from the remov al tool. Ê Remov e the engaging hooks (2) and keep them in a saf e place. 8.6.7 Inser ting an expansion car [...]

144 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Long expansion cards Figure 78: Inserting the expansion card in t he rem ov al tool Ê Inser t the e xpansion card in the slot of the remov al tool. Ê Inser t the green engagi ng hooks in the rods and push them do wn until they engage in the upper edge of the e xpansion card. I Make s ur[...]

RX900 S1 Maintenance Manual 145 Expansion cards and BBU Ê Inser t the e xpansion card in the remov al tool so that as recesses fit e xactly in the remo val tool (see c ircle) and fix the card with the engaging hook (1). Ê Inser t the other two green engaging hooks (2). Check the result of the installation for all expansion car ds Figure 80: P osi[...]

146 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.6.8 Inser ting the ex pans ion ca rd in the slot Figure 81: Inserting the expansion card in t he slot Ê Carefully inser t the removal tool together with the expansion card in the slot (1). Ê Inser t the slot lock (2) and relock the slot (3). Ê Close the hot-plug slot (4). Ê If appli[...]

RX900 S1 Maintenance Manual 147 Expansion cards and BBU 8.6.9 Act iva ting the ex pansion car d Ê Activ ate the ex pansion card using either the related PCI hot-plug software or by pressing the light-pipe s witch, see A in Figure 69 . The light-pipe s witch flashes green. The slot is in the enab le sequence. Ê W ait until the light-pipe s witch i[...]

148 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.7 In stalling a non-hot-plug expansion car d V CA UTION! ● Bef or e installing/remo v ing e xpansion cards to/from the ser ver , turn off the server , all peripheral dev ices, and an y other connected dev i ces. Also unplug all po wer cab les from the power outlet. F ailure to do so c[...]

RX900 S1 Maintenance Manual 149 Expansion cards and BBU 8.7.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rac k" on page 42 4. "Removing the rear co ver" on page 46 5. If applicab le[...]

150 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.7.4 Remo ving the slot co ver Figure 83: Removing the slot cov er Ê Remov e the slot lock b y pulling the green handle upward (1), pushing the plastic par t down (2) and lifting the slot loc k (3). Ê Remov e the slot cover (4). 8.7.5 Inser ting the ex pans ion ca rd in the slot Figure[...]

RX900 S1 Maintenance Manual 151 Expansion cards and BBU Ê Carefully inser t the e x pansion card in the slot (1). Ê Inser t the slot lock (2) and relock the slot (3). Ê If applicab le, connect the cab les on the expansion card. 8.7.6 Installing the PCI Riser (if applicab le) Figure 85: Installing the PCI Ri s er Ê Carefully inser t the PCIR in [...]

152 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.7.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Installing the rear co v er " on page 48 2. "Mounting the server in the rac k" on page 49 3. "Bringing the ser ver bac k to operation" on page 51 4. "Closing the [...]

RX900 S1 Maintenance Manual 153 Expansion cards and BBU 8.8.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Removing the e xpansion card: tool-less 8.8.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 [...]

154 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.8.3 Remo ving the PCI R iser (if a p plicab le) Figure 86: Removing the PCI Ris er Ê Press the green b utton (1). Ê Lift the handle (2) to disconnect the PC I Riser (PCIR) from the baseboard. Ê Pull the PCIR up and out b y using the handle (3). 0 1 /[...]

RX900 S1 Maintenance Manual 155 Expansion cards and BBU 8.8.4 Remo ving the e xpansion car d from the slot Figure 87: Removing the expansion card from the slot Ê If applicab le, remo ve the cabl es from the e x pansion card. Remov e the slot lock b y pulling the gr een handle upw ard (1), pushing the plastic par t down (2), and lifting the slot lo[...]

156 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.8.5 Installing the slot cover Figure 88: Installing the slot cov er Ê Install the slot cov er (1). Ê Inser t the slot lock (2) and relock the slot (3). / 1 0[...]

RX900 S1 Maintenance Manual 157 Expansion cards and BBU 8.8.6 Installing the PCI Riser (if applicab le) Figure 89: Installing the PCI Ri s er Ê Carefully inser t the PCIR in the slot (1). Ê Lock the PCIR by pushing do wn the handle (2). 8.8.7 Complet ing the ta sk Ê P erform the f ollowing procedures to complete the task: 1. "Installing the[...]

158 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.9 Repl acing a non-hot-plug expansion car d V CA UTION! ● Bef or e installing/remo v ing e xpansion cards to/from the ser ver , turn off the server , all peripheral dev ices, and an y other connected dev i ces. Also unplug all po wer cab les from the power outlet. F ailure to do so ca[...]

RX900 S1 Maintenance Manual 159 Expansion cards and BBU 8.9.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. "Shutting down the server" on page 41 4. "Sliding the server out of the rac k" on page 42 5. "Removi[...]

160 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Ê Press the green b utton (1). Ê Lift the handle (2) to disconnect the PC I Riser (PCIR) from the baseboard. Ê Pull the PCIR up and out b y using the handle (3). 8.9.4 Remo ving the e xpansion car d from the slot Figure 91: Removing the e xpansion card from the slot Ê If applicab le, [...]

RX900 S1 Maintenance Manual 161 Expansion cards and BBU 8.9.5 Inser ting the ex pansion car d in the slot Figure 92: Inser ting the expansion card in the slot Ê Carefully inser t the e x pansion card in the slot (1). Ê Inser t the slot lock (2) and relock the slot (3). Ê If applicab le, connect the cab les on the expansion card. 1 / 0[...]

162 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.9.6 Insta lling the PCI Riser (if a pplicab le) Figure 93: Installing the PCI Ris er Ê Carefully inser t the PCIR in the slot (1). Ê Lock the PCIR by pushing do wn the handle (2). 8.9.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Installi[...]

RX900 S1 Maintenance Manual 163 Expansion cards and BBU 8.10 Replacing the Modular RAID control ler V CA UTION! ● Before i ns talling/remo vi ng e xpansion cards to/from the ser ver , tur n off the server , all peripheral devices , and any other connected dev i ces. Also unplug all power cab les from the power outlet. F ailure to do so can cause [...]

164 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.10. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. "Shutting down the s er ver" on page 41 4. "Sliding the server out of the rack " on page 42 5. &[...]

RX900 S1 Maintenance Manual 165 Expansion cards and BBU Ê Press the green b utton (1). Ê Lift the handle (2) to disconnect the PC I Riser (PCIR) from the baseboard. Ê Pull the PCIR up and out by us ing the handle (3). 8.10.4 Remo ving the Modular RAID contro ller Figure 95: Removing the Mod ular RAID cont roller from the slot Ê Remov e the slot[...]

166 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.10.5 Inserting the Modular RAID controller Figure 96: Connecting the SAS cables Ê Connect the SAS cab les to the Modular RAID controller por ts as f ollows: – MLC1 por t (A): HDD/SSD modules #0, #1, #2, #3 – MLC2 por t (B): HDD/SSD modules #4, #5, #6, #7 C A C B[...]

RX900 S1 Maintenance Manual 167 Expansion cards and BBU Figure 97: Inser ting the Modular R AID controller Ê Carefully inser t the Modular RAID controller in its slot (1). Ê Inser t the slot lock (2) and relock the slot (3). 1 0 /[...]

168 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.10.6 Installing the PCI Riser Figure 98: Installing the PCI Ris er Ê Carefully inser t the PCIR in the slot (1). Ê Lock the PCIR by pushing do wn the handle (2). 8.10.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Installing the rear co v [...]

RX900 S1 Maintenance Manual 169 Expansion cards and BBU 8.11 Installing a Battery Backup Unit (BB U ) V CA UTION! ● Do not connect the cable using e xcessiv e force, the connector is weak. ● F ollow the safety instructions in the "Safety instructions" on page 31 . The Battery Backup Unit (BB U ) backs up the memor y contents of the SA[...]

170 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.11. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Removing the rear cov er" on page 46 8.11.3[...]

RX900 S1 Maintenance Manual 171 Expansion cards and BBU 8.11.4 Installing the BBU in the BBU holder Figure 100: Removing the BBU holder Ê Remov e the BBU holder from the chassis by lifting it wi th the green handle. Figure 101: Installing the BBU in the BBU holder / 0 0 1 1 1 / 1 C A C B[...]

172 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Ê Select the battery holder as follo ws: – A : Inser t the BBU f or the Modular RAID controller in PCIe slot #8. – B : Inset the BBU f or one of the SAS RAID controllers. Ê Inser t the batter y at a slight angle behind the clips (1). Ê Carefully press the batter y into the holder u[...]

RX900 S1 Maintenance Manual 173 Expansion cards and BBU 8.11.5 Connecting the BBU to the Modular RAID controller Figure 102: Connecting th e BBU to the Modular RA ID controller / / 0[...]

174 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU Ê Route the BBU cab le through the c able clamps (1). I A void cab le loops in the PCIe slot area. The BBU cable must be fixed in the cab l e clamps (1). Ê Connect the BBU cab le to the Modular RAID controller (2). I The cable can only be installed in one direction. T o distinguish both[...]

RX900 S1 Maintenance Manual 175 Expansion cards and BBU 8.12 Replacing a Battery B ac kup Unit (BB U) V CA UTION! ● Do not connect the cable using e xcessiv e force, the connector is weak. ● Dispose of used battery proper ly . Keep a way fr om children. ● F ollow the safety instructions in the "Safety instructions" on page 31 . 8.12[...]

176 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.12. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Removing the rear cov er" on page 46[...]

RX900 S1 Maintenance Manual 177 Expansion cards and BBU 8.12.3 Disconnecting the BBU fr om the Mo dular RAID controller Figure 103: Disconnecting t he BBU from t he Modular RAID c ontroller Ê Open the cable clamps (1). Ê Disconnect the BBU c able from t he SAS RAID controller (2 ). Ê Remov e the BBU holder from the chassis by lifting it wi th th[...]

178 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU 8.12.4 Remo ving the BBU from the B BU holder Figure 104: Removing the BBU f rom the BBU holder Ê Open the cable c lamps (1). Ê Carefully press the two loc king hooks (2) outward so that the BBU can be remov ed from the holder at a slight angle (3). / 0 0 / / / 1[...]

RX900 S1 Maintenance Manual 179 Expansion cards and BBU 8.12.5 Disconnecting the BBU cable fr om the BBU Figure 105: Disconnecting t he BBU cable Ê Disconnect the BBU c able from the battery . 8.12.6 Reinstalling a ne w BBU Ê P erform the f ollowing two steps: 1. "Connecting the BBU cab le to the BBU" on page 170 2. "Installing the[...]

180 Maintenance Manual RX900 S1 Ex pans ion c ar ds and B BU[...]

RX900 S1 Maintenance Manual 181 9M a i n m e m o r y V CA UTION! ● The actions described in this section ma y only be perf ormed by personnel with the appropriate technical training. (The device can be seriously damaged if it is opened without authorization or if repairs are attempted by untrained personnel .) ● Do not install unauthorized thir[...]

182 Maintenance Manual RX900 S1 Main memory The baseboard can be configured with up to 8 CPUMEMRs. Each CPUMEMR includes one processor and can be equipped with up to 16 memory modules. There are two wa ys to ex pand the main memor y: ● Filling the empty slots of an already populat ed CPUMEMRs, see "Installing additional DIMM memory modules&q[...]

RX900 S1 Maintenance Manual 183 Main memory 9.1 I nstalling a CPUMEMR I The CPUMEMRs must be install ed ac co rding to the configur ation r ules summarized in "Selecting the CPUMEMR sl ot" on page 184 and described in the "Baseboard D3081, CPUMEMR D3131, PCIR D3082 for PRIME R GY RX900 S1 T echnical Manual". 9.1.1 Required tools[...]

184 Maintenance Manual RX900 S1 Main memory 9.1.3 P opulating th e CPUMEMR Ê P opulate the DIMM memory module slots by using the f ollowi ng procedures: 1. "Selecting the DIMM memory module slot" on page 192 2. "Inser ting the DIMM memor y module in the slot" on page 194 9.1.4 Selec ting the CPUMEMR sl ot Ê Choose the CPUMEMR [...]

RX900 S1 Maintenance Manual 185 Main memory Figure 106: CPUM EMR slot assignmen t 9.1.5 Removing the air duct (if applicable) Figure 107: Removing an air duct Ê Press the green b uttons (1). Ê Lift the handles (2) to disconnect the air duct from the baseboard. Ê Carefully pull the air duct up and out (3). / 2 1 4 0 6 3 5 / 0 / 0 1[...]

186 Maintenance Manual RX900 S1 Main memory 9.1.6 Ins erting the CPUME MR in the slot Figure 108: Inser ting the CPUMEMR in the slot Ê Carefully inser t the CPUMEMR in the slot. I Please make s ure that you place the PCB and not the metal shiel d in the guides (1). Figure 109: Loc king the CPUMEMR Ê Lock the CPUMEMR by pus hing down the handles ([...]

RX900 S1 Maintenance Manual 187 Main memory 9.1.7 Inser ting the air duct in the slot (if applicable) Only applicab le for 4 and 6 CPUMEMR configurati ons. Figure 110: Inser tin g the air duct Ê Inser t the air duct in the CPUMER slot (1) as f ollows: – 4 CPUMEMR configuration: s l ot 6 – 6 CPUMEMR configuration: s l ot 8 Ê Lock the air duct [...]

188 Maintenance Manual RX900 S1 Main memory 9.2 Repl acing a faulty CPUMEMR 9.2.1 Required tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the CPUMEMR: tool-less 9.2.2 Star t ing t he ta sk Ê P erf or m the f ollowing procedures: 1. "Opening the rac k doo[...]

RX900 S1 Maintenance Manual 189 Main memory 9.2.3 Identifying a fault o n the CPUMEMR CPUMEMRs provide PRIMERGY Diagnos tics indicators to indicate f aulty CPUMEMRs, CPUs , or DIMM memor y modules see figure 111 . Figure 111: Indicators on the CPUM EMR Ê Press the CSS b utton that is located on the PCI Riser to identify a f aulty CPUMEMR or a f au[...]

190 Maintenance Manual RX900 S1 Main memory 9.2. 4 Remo ving the C PUMEM R Figure 112: Removing a CPUMEMR Ê Press the green b uttons (1). Ê Lift the handles (2) to disconnect the CPUMEMR from the baseboard. Ê Carefully pull the CPUMEMR up and out (3). 9.2.5 Rei nstalling a ne w CPUME MR Ê P opulate the DIMM memory module slots: 1. Cross-check t[...]

RX900 S1 Maintenance Manual 191 Main memory 9.2.6 Complet ing the ta sk P erform the f ollowing procedures to complete the task: 1. "Closing the server" on page 47 2. "Mounting the server in the rac k" on page 49 3. "Bringing the ser ver bac k to operation" on page 51 4. "Closing the rac k door" on page 51 9.[...]

192 Maintenance Manual RX900 S1 Main memory 9.3.2 Star t ing t he ta sk Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Opening the server" on page 44 5. "Removing the CPUME [...]

RX900 S1 Maintenance Manual 193 Main memory Figure 113: P o pulation order for DIMM memor y modules I Only use identical DIMM m emor y modules in t he minimum configuration. P opulat ion order DIMM position 1 1B + 1D + 1F + 1H 2 1A + 1C+ 1 E + 1 G 3 2B + 2D + 2F + 2H 4 2A + 2C + 2 E + 2 G T ab le 4: P opulation order f or DIMM memor y modules B 1C [...]

194 Maintenance Manual RX900 S1 Main memory 9.3.4 Inser ting the DIMM memory module in the slot Figure 114: Inser ting a DIMM memory module Ê Carefully press the DIMM memory module into the slot (1) until the securing clips on both sides of it engage (2). 9.3.5 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. &q[...]

RX900 S1 Maintenance Manual 195 Main memory 9.4 Replacing a faulty m emory module 9.4.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the DIMM memory module: tool-less 9.4.2 Sta r ting the task Ê P erform the f ollowing procedures: 1. "Opening t[...]

196 Maintenance Manual RX900 S1 Main memory 5. "Opening the server" on page 44 6. "Locate the f aulty component by PRIMERGY diagnos tics indicators" on page 39 7. "Identifying a f ault on the CPUMEMR" on page 189 8. "Removing the CPUME MR" on page 190 9.4.3 Remo ving the DIMM memory module Figure 115: Removin[...]

RX900 S1 Maintenance Manual 197 Main memory Figure 116: Installing a D IMM mem ory module Ê Carefully press the DIMM memory module into the slot (1) until the securing clips on both sides of it engage (2). 9.4.5 Complet ing the ta sk Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on pa[...]

198 Maintenance Manual RX900 S1 Main memory[...]

RX900 S1 Maintenance Manual 199 10 Pr ocesso rs V CA UTION! ● Before ins talling/removing processors to/from the ser ver , tur n off the server , all peripheral de vices, and an y other connected de vices. A lso unplug all po wer c ords from the power outl et. F ailure to do so can cause electric shock. ● Do not touch the circuitr y on boards a[...]

200 Maintenance Manual RX900 S1 Processor s 10.1 Installi n g a processor in a ne w CPUMEMR A new CPUME MR comes together with a heat sink. This procedure explai ns how to inst all a processor in a new CPUMEMR. V CA UTION! Only processors of the same type ma y be used in the server . That means the number of the internal processor cores as well as [...]

RX900 S1 Maintenance Manual 201 Processors 10.1.2 Star ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rac k" on page 42 4. "Opening the server" on page 44 5. "Removing the CPUME MR"[...]

202 Maintenance Manual RX900 S1 Processor s 10.1.4 Installing the pr ocessor Figure 118: Inser ting the processor Ê Hold the processor betw een your thumb and inde x finger and ali gn it at the soc ket coding. V CA UTION! The processor can only be install ed in one direction. Mak e sure that: – the recesses on the processor (A) are aligned with [...]

RX900 S1 Maintenance Manual 203 Processors Ê Place the processor in the sock et with great care. V CA UTION! Do not mov e the proc essor within the sock et. This would damage the spring contacts of the socket. Ne ver touch the u nderside of the processor . Even light c ontaminants, s uch as oil from human skin, c an destroy the proces sor or impai[...]

204 Maintenance Manual RX900 S1 Processor s Figure 120: Applying the t hermal paste Ê Apply the thermal paste in the center of the processor surface (see circle). Ê Ensure a thin and e ven distribution of the thermal paste.[...]

RX900 S1 Maintenance Manual 205 Processors 10.1.6 Installing the heat sink Figure 121: Installing the heat sink Ê Carefully place the heat sink onto the processor . V CA UTION! Place the heat sink precisely on the threaded holes (see circles). Careless handling ma y damage conductors and render the baseboard useless. Ê F asten the heat sink with [...]

206 Maintenance Manual RX900 S1 Processor s 10.1.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page 186 2. "Closing the server" on page 47 3. "Mounting the server in the rac k" on page 49 4. "Bringing the ser ver bac k to operation&qu[...]

RX900 S1 Maintenance Manual 207 Processors 10.2.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the processor: – Phillips Ph2 scre w dr iver 10.2.2 Star ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on pag[...]

208 Maintenance Manual RX900 S1 Processor s 10.2.3 Remo ving the heat sink Figure 122: Removing the heat sink Ê Loosen the captiv e scre ws of the heat sink alternately until they are fully released. Ê Loosen the heat sink b y turning it back and f or th and then lift it out.[...]

RX900 S1 Maintenance Manual 209 Processors 10.2.4 Remo ving the processor Figure 123: Removing the processor Ê Release the soc ket lev er by pressing it do wnward and outward (1). Ê Open the sock et lev er and the process or holder (2). Ê Lift the installed processor carefully out of the soc ket (3). V CA UTION! Do not bend the spring contacts o[...]

210 Maintenance Manual RX900 S1 Processor s 10.2.5 Installing the pr ocessor Figure 124: Inser ting the processor Ê Hold the processor betw een your thumb and inde x finger and ali gn it at the soc ket coding. V CA UTION! The processor can only be install ed in one direction. Mak e sure that: – the recesses on the processor (A) are aligned with [...]

RX900 S1 Maintenance Manual 211 Processors Ê Place the processor in the sock et with great care. V CA UTION! Do not mov e the proc essor within the sock et. This would damage the spring contacts of the socket. Ne ver touch the u nderside of the processor . Even light c ontaminants, s uch as oil from human skin, c an destroy the proces sor or impai[...]

212 Maintenance Manual RX900 S1 Processor s Figure 126: Applying the t hermal paste Ê Apply the thermal paste in the center of the processor surface (see circle). Ê Ensure a thin and e ven distribution of the thermal paste.[...]

RX900 S1 Maintenance Manual 213 Processors 10.2.7 Installing the heat sink Figure 127: Installing the heat sink Ê Remov e the residual ther mal paste from the underside of the heat sink. Ê Clean the heat sink using a lint-free cloth. Ê Carefully place the heat sink onto the processor . V CA UTION! Place the heat sink precisely on the threaded ho[...]

214 Maintenance Manual RX900 S1 Processor s Ê F asten the heat sink with its fiv e captive scre ws. F asten the screws alternately until the y are fully tightened: – Giv e each screw about 4 tur ns at a time. – Star t with screw 1 to screw 5 as indicated in figure 127 and contin ue with screw 1. – T orque: 0.6 Nm 10.2.8 Completing the task ?[...]

RX900 S1 Maintenance Manual 215 Processors 10.3 Replacing a heat sink V CA UTION! Only processors of the same type may be used on the baseboard. T hat means the number of the i nter nal processor cores as well as the primar y clock and the FSB frequency hav e to be the same. F or multi-processor operation, use a suitab le multiprocessor operating s[...]

216 Maintenance Manual RX900 S1 Processor s 4. "Sliding the server out of the rack " on page 42 5. "Opening the server" on page 44 6. "Removing the CPUME MR" on page 190 10.3.3 Remo ving the heat sink Figure 128: Removing the heat sink Ê Loosen the captiv e scre ws of the heat sink alternately until they are fully rel[...]

RX900 S1 Maintenance Manual 217 Processors 10.3.4 Appl ying the thermal paste Figure 129: Measur ing the ther mal pa ste Ê Remov e the residual ther mal paste from the processor surf ac e. Ê Clean the processor surf ace using a lint-free cloth. Ê Use 0.2 grams of the s upplied thermal paste, that is appro ximately one graduation mark of the prov[...]

218 Maintenance Manual RX900 S1 Processor s Figure 130: Applying the t hermal paste Ê Apply the thermal paste in the center of the processor surface (see circle). Ê Ensure a thin and e ven distribution of the thermal paste.[...]

RX900 S1 Maintenance Manual 219 Processors 10.3.5 Installing the heat sink Figure 131: Installing the heat sink Ê Carefully place the heat sink onto the processor . V CA UTION! Place the heat sink precisely on the threaded holes (see circles). Careless handling ma y damage conductors and render the baseboard useless. Ê F asten the heat sink with [...]

220 Maintenance Manual RX900 S1 Processor s 10.3.6 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page 186 2. "Closing the server" on page 47 3. "Mounting the server in the rac k" on page 49 4. "Bringing the ser ver bac k to operation&qu[...]

RX900 S1 Maintenance Manual 221 11 Optical and bac kup drives One optical driv e is installed i n the RX900 S1. Y ou can choose a D VD or Blu- Ray SA T A drive in 0.5x 5.25- inch f or mat. 11.1 Replacing the optical drive V CA UTION! ● Bef ore installing/remo ving an accessible driv e to/from the ser ver , tur n off the server , all peripheral de[...]

222 Maintenance Manual RX900 S1 Optical and backup drives V CA UTION! ● When f orcing an accessible drive into a server , be careful so as not to pinch the cabl e etc. connected to an accessibl e drive. ● F ollow the saf ety instr uctions in the "Safety instructions" on page 31 . 11.1.1 Requir ed tools ● Star ting and completing the[...]

RX900 S1 Maintenance Manual 223 Optical and backup drives 11.1.3 Remo ving the optical drive Figure 132: Removing the opt ical drive Ê Disconnect the SA T A cab le (A) and the power c able (B) from the bac k of the optical driv e (1). Ê Use the handle (C) to unloc k the drive (2). Ê Remov e the optical drive from the ba y (3). 11.1.4 Replac ing [...]

224 Maintenance Manual RX900 S1 Optical and backup drives Ê Remov e the four scre ws (see circles) to remo ve the drive fr ames. Ê Put the old optical driv e aside. Ê F asten the drive frames at the ne w optical drive with the f our supplied scre w s (see circ les). 11.1.5 Installing the optical drive Figure 134: Sliding t he optical drive in th[...]

RX900 S1 Maintenance Manual 225 Optical and backup drives 11.1.6 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Closing the server" on page 47 2. "Mounting the server in the rac k" on page 49 3. "Bringing the ser ver bac k to operation" on page 51 4. "Closing the rac k door&quo[...]

226 Maintenance Manual RX900 S1 Optical and backup drives[...]

RX900 S1 Maintenance Manual 227 Front panel and ext ernal connectors 12 Fr ont panel and ex ternal conn ector s V CA UTION! F ollow the s af ety instructions in the chapter "Saf ety instructions" on page 31 . This section comprises procedures on: ● "Replacing the control panel" on page 228 ● "Replacing the front panel m[...]

228 Maintenance Manual RX900 S1 Front panel and external connectors 12.1 Replacing the control panel 12.1.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the control panel: tool-less 12.1. 2 Star ting the task Ê P erf or m the f ollowing procedures[...]

RX900 S1 Maintenance Manual 229 Front panel and ext ernal connectors 12.1.3 Remo ving the control panel Figure 136: Disconnecting t he contro l panel cable f r om the baseboard Ê Disconnect the control panel cab le from the baseboard (1). Ê Open the cable clamp (2). Figure 137: Removing the control panel / 0 / / 0[...]

230 Maintenance Manual RX900 S1 Front panel and external connectors Ê Press the plastic tongues slightly outw ard as indicated by the arrows (1 ). Ê Push the control panel outward (2). 12.1.4 Disconnecting th e control panel cabl e Figure 138: Disconnecting the control panel c able fr om the control panel Ê Disconnect the control panel cab le fr[...]

RX900 S1 Maintenance Manual 231 Front panel and ext ernal connectors 12.1.5 Connecting the control panel cab le Figure 139: Connecting the control panel cable to the control panel Ê Connect the control panel cab le to the control panel.[...]

232 Maintenance Manual RX900 S1 Front panel and external connectors 12.1.6 Installing the control pa nel Figure 140: Installing the control panel Ê Slide the control panel into the ba y until it clicks into place .[...]

RX900 S1 Maintenance Manual 233 Front panel and ext ernal connectors Figure 141: Connecting th e control panel cable Ê Connect the control panel cab le to the baseboard (1). Ê Close the cable c lamp (2). 12.1.7 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page[...]

234 Maintenance Manual RX900 S1 Front panel and external connectors 12.2 Replacing th e fr ont panel mod ule 12.2.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the front panel module: tool-les s 12.2. 2 Star ting the task Ê P erf or m the f ollow[...]

RX900 S1 Maintenance Manual 235 Front panel and ext ernal connectors 12.2.3 Remo ving the front panel module Figure 142: Disconnecting t he USB ca ble and t he video connector Ê Disconnect the USB cab le (1). Ê Press the lock ing handle (2) of the video connector downw ard. Ê Slide the video connector out of the front panel module (3). 0 / 1[...]

236 Maintenance Manual RX900 S1 Front panel and external connectors Figure 143: Removing t he front panel module Ê Press the loc king handle (1) downw ard. Ê Push the front panel module outw ard (2). 0 /[...]

RX900 S1 Maintenance Manual 237 Front panel and ext ernal connectors 12.2.4 Inserting the front panel module Figure 144: Inser ting t he front panel module Ê Slide the front panel module into the ba y until it clic ks into place (1). Ê Slide the video connector in th e front panel module until it cl ick s into place (2). 0 /[...]

238 Maintenance Manual RX900 S1 Front panel and external connectors Figure 145: Connecting the USB cab le Ê Connect the USB cab le to the front panel module . 12.2.5 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Installing the control panel" on page 232 2. "Inser ting the CPUMEMR in the slot&q[...]

RX900 S1 Maintenance Manual 239 Front panel and ext ernal connectors 12.3 Replacing the USB boar d 12.3.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the USB board: – Phillips Ph1 scre w dr iver 12.3.2 Star ting the task Ê P erform the f ollowing[...]

240 Maintenance Manual RX900 S1 Front panel and external connectors 6. Remov e all CPUMEMRs, see "Remo ving the CPUMEMR" on page 190 I Bef or e remo v ing the CPUMEMRs, take a note on the installati on slot number f or each CPUMEMR. Make sure that you re install the CPUMEMR in the slot it was located before the replacement. 7. "Remov[...]

RX900 S1 Maintenance Manual 241 Front panel and ext ernal connectors 12.3.4 Installing the USB boar d Figure 147: Installing t he USB board in the front panel module Ê Inser t the USB board into the front panel module. Ê F asten both screws (see circles). 12.3.5 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. &q[...]

242 Maintenance Manual RX900 S1 Front panel and external connectors 12.4 Replacing the I/O board 12.4.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the I/O board: – Phillips Ph2 sc rew driver 12.4. 2 Star ting the task Ê P erf or m the f ollowi[...]

RX900 S1 Maintenance Manual 243 Front panel and ext ernal connectors 12.4.3 Removing the P CI Riser Figure 148: Removing the PCI Ri ser Ê Press the green b utton (1). Ê Lift the handle (2) to disconnect the PC I Riser (PCIR) from the baseboard. Ê Pull the PCIR up and out by us ing the handle (3). 0 1 /[...]

244 Maintenance Manual RX900 S1 Front panel and external connectors 12.4.4 Removing the I /O boar d Figure 149: Removing the I / O board Ê Loosen the two captiv e screws (see circles). Ê Remov e the I/O board. 12.4.5 Installing the I/O boar d Figure 150: Installing the I /O board[...]

RX900 S1 Maintenance Manual 245 Front panel and ext ernal connectors Ê Carefully inser t the I/O board in the I/O board connector . Ê F asten the two screws (see circles ). 12.4.6 Installing the PCI Riser Figure 151: Installing the PCI Ri ser Ê Carefully inser t the PCIR in the slot (1). Ê Lock the PCIR by pushing do wn the handle (2). 12.4.7 C[...]

246 Maintenance Manual RX900 S1 Front panel and external connectors[...]

RX900 S1 Maintenance Manual 247 Management and diagnostics mod ules 13 Management and dia gnostics modules V CA UTION! F ollow the s af ety instructions in the chapter "Saf ety instructions" on page 31 . This section prov ides inf or mation on: ● "Replacing the local service displa y" on page 248 The Ser v erView Local Ser vic[...]

248 Maintenance Manual RX900 S1 Management and diagnostics modu les 13.1 Replacing the loc al service displa y 13.1.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the local s er vice displa y : tool-less 13.1. 2 Star ting the task Ê P erf or m the[...]

RX900 S1 Maintenance Manual 249 Management and diagnostics mod ules 13.1.3 Removing the loc a l service dis play Figure 152: Removing the local ser vice display Ê Unloc k the local s er vice displa y (1). Ê Slide the local service displa y outward so that y ou can disconnect the chassis ID board cable (2). Ê Disconnect the chassis ID board cable[...]

250 Maintenance Manual RX900 S1 Management and diagnostics modu les 13.1.4 Inserting the local se rvice displa y Figure 153: Inserting the local ser vice displa y Ê Slide the local ser vice displa y in the bay so that there is enough space to connect the chassis ID board cabl e.[...]

RX900 S1 Maintenance Manual 251 Management and diagnostics mod ules Figure 154: Connecting the chassis ID board cable Ê Connect the chassis ID board cable (1). Ê Slide the local service displa y inward until i t clic ks into place (2). 13.1.5 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the C[...]

252 Maintenance Manual RX900 S1 Management and diagnostics modu les 13. 2 Re pl aci ng the chas sis ID b oard 13.2.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the chassis ID board: tool-less 13.2. 2 Star ting the task Ê P erf or m the f ollowin[...]

RX900 S1 Maintenance Manual 253 Management and diagnostics mod ules 13.2.3 Removing the c hassis ID boar d Figure 155: Removing the chassis ID board cab l e from the local service displa y Ê Unloc k the local s er vice displa y (1). Ê Slide the local service displa y outward so that y ou can disconnect the chassis ID board cable (2). Ê Disconnec[...]

254 Maintenance Manual RX900 S1 Management and diagnostics modu les Figure 156: Removing the chassis ID board holder Ê Disconnect the chassis ID board cab le from the baseboard (1) and open the cable cl amp (2). Ê Press the plastic tongues of the chassis ID board holder slightly inw ar d as indicated by the arrows (3). Ê Slide the chassis ID boa[...]

RX900 S1 Maintenance Manual 255 Management and diagnostics mod ules Figure 157: Removing the connector clamp Ê Remov e the connector clamp. Figure 158: Disconnecting t he chassis ID boar d cable Ê Disconnect the chassis ID board cable from the chassis ID board (1). Ê Slide the chassis ID board out of the holder (2). / 0[...]

256 Maintenance Manual RX900 S1 Management and diagnostics modu les 13.2.4 Inst all ing the chass is ID bo ard Figure 159: Installing the chassis ID board Ê Slide the chassis ID board in the hol der (1). Ê Connect the chassis ID board cable at the chassis ID board (2). Figure 160: Installing the connector clamp Ê Install the connector clamp . 0 [...]

RX900 S1 Maintenance Manual 257 Management and diagnostics mod ules Figure 161: Installing the chassis ID board holder Ê Press the plastic tongues of the chassis ID board holder slightly inw ar d as indicated b y the arrows (1) and slide the c has sis ID board holder inw ard until it clic ks into place (2). Ê Connect the chassis ID board cable at[...]

258 Maintenance Manual RX900 S1 Management and diagnostics modu les Figure 162: Connecting the chassis ID board cab le Ê Connect the chassis ID board cable (1). Ê Slide the local serv ice displa y inward until it clic ks into place (2). I In order to enable ServerVie w Operations Manager and Ser v erView Installation Manager to identify the syste[...]

RX900 S1 Maintenance Manual 259 Management and diagnostics mod ules 13.2.5 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page 186 2. "Closing the server" on page 47 3. "Mounting the server in the rac k" on page 49 4. "Bringing the ser ver[...]

260 Maintenance Manual RX900 S1 Management and diagnostics modu les[...]

RX900 S1 Maintenance Manual 261 Baseboard 14 Baseboar d V CA UTION! F ollow the s af ety instructions in the chapter "Saf ety instructions" on page 31 . This section comprises procedures on: ● "Replacing the lithium battery" on page 262 ● "Installing the UFM" o n page 264 / "Replacing the UFM board" on pa[...]

262 Maintenance Manual RX900 S1 Baseboard 14.1 Replacing the lithiu m battery T o allow per manent sa ving of the system inf or mation, a lithium batter y is installed which supplies the CMOS memor y with po wer . If the battery v oltage is too low or the battery is empty , a corresponding error message is displa yed. The lithium battery must then [...]

RX900 S1 Maintenance Manual 263 Baseboard 14.1.2 Star ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rac k" on page 42 4. "Removing the rear co ver" on page 46 5. Remov e the PCI Riser , see [...]

264 Maintenance Manual RX900 S1 Baseboard 14.1.4 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. Installing the PCI Riser , s ee "Expansion cards and BBU" on page 105 2. "Installing the rear co v er " on page 48 3. "Mounting the server in the rac k" on page 49 4. "Bringing the [...]

RX900 S1 Maintenance Manual 265 Baseboard 14.2.2 Star ting the task Ê P erform the f ollowing procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rac k" on page 42 4. "Removing the rear co ver" on page 46 5. If required to access the in[...]

266 Maintenance Manual RX900 S1 Baseboard Figure 165: Checking the installation position Ê Remov e the SAS and BB U cable(s) for a conveni ent access to the mounting location of the UFM. Ê Make s ure that the metal spacer (A) engages properly in the baseboard. Figure 166: Installing the UFM board Ê Place the UFM on the metal s pacer (A) and the [...]

RX900 S1 Maintenance Manual 267 Baseboard 14.3 Replacing the UFM board 14.3.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the UFM: – Phillips Ph1 scre w dr iver A u thoriz ed personnel A uthor ized specialist personnel c an carr y out replacement [...]

268 Maintenance Manual RX900 S1 Baseboard 14.3. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Removing the rear cov er" on page 46 5. If required to access [...]

RX900 S1 Maintenance Manual 269 Baseboard 14.3.4 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the UFM" on page 265 2. When e xpansion cards hav e been removed to acc ess the installation place: Install the e xpansion cards, s ee "Expansion cards and BBU" on page 105 3. "Inst[...]

270 Maintenance Manual RX900 S1 Baseboard 14.4 Insta llin g the TPM 14.4.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Installing the TPM: – Phillips Ph0 sc rew driver 14.4. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening th[...]

RX900 S1 Maintenance Manual 271 Baseboard 14.4.3 Inser ting the TPM Figure 168: TPM board Server-specific inst allation rules are: ● Only the TPM board is used from the av ailable TPM ins tallation kit, see figure 168 . ● The metal spacer and the Phillips scre w ar e already installed on the baseboard. Figure 169: Checking the installation posi[...]

272 Maintenance Manual RX900 S1 Baseboard Figure 170: Installing the T PM board Ê Place the TPM board on the metal spacer (A) and soc ket (B) in figure 169 and f asten it with the Phillips screw . 14.4.4 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. Install the PCI Riser , see "Expansion cards and BBU&qu[...]

RX900 S1 Maintenance Manual 273 Baseboard 14.5 Replacing the TPM V CA UTION! – Advise y our contact persons that they m ust provide y ou with TPM backup c opies. For security reasons, the TPM m ust be restored/re- sav ed by the customer . After installin g a new baseboard the TPM must be enab led. Y ou may not clear the TPM data. If the contact p[...]

274 Maintenance Manual RX900 S1 Baseboard 14.5. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Opening the server" on page 44 14.5.3 Remo ving the TPM Figure[...]

RX900 S1 Maintenance Manual 275 Baseboard 14.5.4 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Installing the TPM" on page 270 2. "Closing the server" on page 47 3. "Mounting the server in the rac k" on page 49 4. "Bringing the ser ver bac k to operation" on page 51 5. &q[...]

276 Maintenance Manual RX900 S1 Baseboard 14.6 Replacing the baseboar d I The baseboard is optionally equipped with a T r usted Platf orm Module (TPM). This module enables programs from third par ty manuf acturers to store ke y information, f or e xample driv e enc r yption using Windows Bitloc ker Driv e Encr yption. The TPM is activ ated via the [...]

RX900 S1 Maintenance Manual 277 Baseboard 14.6.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the baseboard: – Phillips Ph0 scre w dr iver – Phillips Ph1 scre w dr iver – Phillips Ph2 scre w dr iver 14.6.2 Star ting the task Ê P erform the f o[...]

278 Maintenance Manual RX900 S1 Baseboard 9. Remov e the PCI Riser , see "Expansion cards and BBU" on page 105 10. Remo v e the BBU holder , see "Expansion cards and BBU" on page 105 11. "Remo ving the I/O board" on page 244 12. "Remo ving the UFM" on page 268 13. "Remo ving the TPM" on page 274 14.[...]

RX900 S1 Maintenance Manual 279 Baseboard 14.6.4 Disconnecting the cables Figure 173: Disconnecting t he cables from the baseboard Ê Disconnect the f ollowing cables from the baseboard: – SAS bac kplane cable (1) – Signalling cabl e ( 2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5) –[...]

280 Maintenance Manual RX900 S1 Baseboard 14.6.5 Removing the fa n cage Figure 174: Removing the f an cage Ê Loosen the captiv e screws (1). Ê Lift the f an cage out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 281 Baseboard 14.6.6 Remo ving the CPUMEMR guide Figure 175: Removing the CPUMEMR guide Ê Loosen the captiv e screws of the CPUMEMR gui de (1). Ê Lift the CPUMEMR guide out of the chassis (2). / / 0[...]

282 Maintenance Manual RX900 S1 Baseboard 14.6.7 Remo ving the air guide Figure 176: Removing the air guide Ê Loosen the captiv e screws (1). Ê Lift the air guide out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 283 Baseboard 14.6.8 Remo ving the baseboard Figure 177: Removing the baseboard Ê Loosen the captive s c rews (1). Ê Slide the baseboard appro ximately 1 cm in the direction of the arrow (2). V CA UTION! Make su re that you ha ve remov ed all power supply units bef ore removing the baseboard. Otherwise, the po wer supp[...]

284 Maintenance Manual RX900 S1 Baseboard 14.6.9 Inserting the baseboard Figure 178: Inser ting the baseboard Ê Carefully low er the baseboard in the chassis b y using the handle (1). Ê Slide the baseboard in the dire ction of the arrow (2) until it is into place. Ê F asten the captive scre ws (3). V CA UTION! After installing the ne w baseboard[...]

RX900 S1 Maintenance Manual 285 Baseboard V CA UTION! Ensure not to damage the EMI springs to comply with appl icabl e EMC regulations and satisfy cooling requi rements and fire protection measures. 14.6.10 Installing the air guide Figure 179: Installing the air gui de Ê Place the air guide in th e chassis (1). Ê F asten the captiv e screws (2). [...]

286 Maintenance Manual RX900 S1 Baseboard 14.6.11 Inser ting the CPUMEMR guide Figure 180: Inserting the CPUME MR guide Ê Inser t the CPUMEMR guide in the installation s lot (1). Ê F asten the captiv e screws of the CPUMEMR guid e ( 2). 0 0 /[...]

RX900 S1 Maintenance Manual 287 Baseboard 14.6.12 Inserti ng the fan cage Figure 181: Inser ting t he fan cage Ê Inser t the f an cage in the bay (1). Ê F asten the captiv e screws (2). / 0 0[...]

288 Maintenance Manual RX900 S1 Baseboard 14.6.13 Connecting the ca bles to the baseboard Figure 182: Connecting the cab l es to the baseboard Ê Connect the f ollowing cables to the baseboard: – SAS backpl ane cable (1) – Signalling cab le (2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable ([...]

RX900 S1 Maintenance Manual 289 Baseboard 14.6.14 Sliding the local service displa y inward Figure 183: Sliding the local service displa y inward Ê Slide the local ser vice displa y inwa rd until it clic ks into place. 14.6.15 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. "Inser ting the TPM" on page [...]

290 Maintenance Manual RX900 S1 Baseboard 7. Install all C PUMEMRs, see "Remo ving the CPUMEMR" on page 190 I Make s ure that you reinstall eac h C PUMEMR in the slot it w as located bef ore the replacement. 8. Install all PSUs, see "Installing a pow er supply unit" on page 55 9. "Closing the server" on page 47 10. &qu[...]

RX900 S1 Maintenance Manual 291 Cables 15 Cables V CA UTION! F ollow the s af ety instructions in the chapter "Saf ety instructions" on page 31 . This section comprises procedures on replacing the f ollowing c ables: ● "Replacing the control panel cab le" on page 301 ● "Replacing the chassis ID board cab le" on pag[...]

292 Maintenance Manual RX900 S1 Cables 15.1 Replacing the fan cables 15.1.1 Requir ed tools ● Star ting and completing the task: – ke y for the r ack doors (if appli c able) – Phillips Ph2 sc rew driver ● Replacing the f an cable: – Phillips Ph0 sc rew driver – Phillips Ph2 sc rew driver 15.1. 2 Star ting the task Ê P erf or m the f ol[...]

RX900 S1 Maintenance Manual 293 Cables 6. Remov e all CPUMEMRs, see "Remov ing the CPUMEMR" on page 190 I Before remo ving the CPUMEMRs, tak e a note on the installation slot number f or each CPUMEMR. Make sure that y ou r einstall the CPUMEMR in the slot it was located before the replacement. 7. Remov e all expansion c ards and dummy mod[...]

294 Maintenance Manual RX900 S1 Cables 15.1.4 Remo ving the CPUMEMR guide Figure 185: Removing the CPUMEMR guide Ê Loosen the captiv e scre ws of the CPUMEMR guide (1). Ê Lift the CPUMEMR guide out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 295 Cables 15.1.5 Removing the fa n cable Figure 186: Removing the f a n cab le Ê Remov e the screws and the plug was hers of the fan c onnec tors (1). I Be careful while remo vi ng the scre ws as the plug was hers might f all on the baseboard. Ê Rotate each connector by 90° (2) and slide it in the cutout of the fan b[...]

296 Maintenance Manual RX900 S1 Cables Figure 187: Disconnecting t he fan cabl e Ê Disconnect the f an cable from the baseboard.[...]

RX900 S1 Maintenance Manual 297 Cables 15.1.6 Installing the fan ca ble Figure 188: Co nnecting the fan cable Ê Connect the f an c abl e to the baseboard.[...]

298 Maintenance Manual RX900 S1 Cables Figure 189: Installing the f an cable Ê Pull the connectors underneath the f an base as indicated b y the arrow (1). Ê Slide each connector through the cutout of the f an base (2) and rotate it by 90° (3). Ê F asten the screws and the plug w as hers of the f an connectors (4). I Be careful while ins er tin[...]

RX900 S1 Maintenance Manual 299 Cables 15.1.7 Inserting the CPUMEMR guide Figure 190: Inser ting the CPUME MR guide Ê Inser t the CPUMEMR guide in the installa tion s lot (1). Ê F asten the captiv e screws of the CPUM EMR guide (2). 0 0 /[...]

300 Maintenance Manual RX900 S1 Cables 15.1.8 Inser ting the fan cage Figure 191: Inser ting the fan cage Ê Inser t the f an cage in the bay (1). Ê F asten the captive scre ws (2). 15.1.9 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. Install the PCI Riser , see "Expansion cards and BBU" on page 105[...]

RX900 S1 Maintenance Manual 301 Cables 4. "Closing the server" on page 47 5. "Mounting the server in the rac k" on page 49 6. "Bringing the ser ver bac k to operation" on page 51 7. "Closing the rac k door" on page 51 15.2 Replacing the contr o l panel cable 15.2.1 Required tools ● Star ting and completing [...]

302 Maintenance Manual RX900 S1 Cables 15.2. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Shutting down the s er ver" on page 41 3. "Sliding the server out of the rack " on page 42 4. "Opening the server" on page 44 5. Remov e all CPUMEMRs, see "[...]

RX900 S1 Maintenance Manual 303 Cables Figure 193: Removing the control panel Ê Press the plastic tongues slightly outward as indicated b y the arrows (1). Ê Push the control panel outward (2). 15.2.4 Disconnecting the control panel cable Figure 194: Disconnecting t he control panel cable from the control panel Ê Disconnect the control panel cab[...]

304 Maintenance Manual RX900 S1 Cables 15.2.5 Connecting the control panel cable Figure 195: Connecting the control panel cable to the control panel Ê Connect the control panel cab le to the control panel.[...]

RX900 S1 Maintenance Manual 305 Cables 15.2.6 Installing the contr ol panel Figure 196: Installing the cont rol panel Ê Slide the control panel into the bay until it c lic ks into place.[...]

306 Maintenance Manual RX900 S1 Cables Figure 197: Connecting the control panel cable Ê Connect the control panel cab le to the baseboard (1) . Ê Close the cabl e clamp (2). 15.2.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page 186 2. "Closing the se[...]

RX900 S1 Maintenance Manual 307 Cables 15.3 Replacing the chassis ID boar d cable 15.3.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the chassis ID board cab le: tool-less 15.3.2 Star ting the task Ê P erform the f ollowing procedures: 1. "Ope[...]

308 Maintenance Manual RX900 S1 Cables 15.3.3 Removing the c hassis ID boar d Figure 198: Removing the chassis ID board cable from the local s er vice displa y Ê Unloc k the local service displa y (1). Ê Slide the local ser vice displa y outward so that you can disc onnect the chassis ID board cabl e ( 2). Ê Disconnect the chassis ID board cable[...]

RX900 S1 Maintenance Manual 309 Cables Figure 199: Removing the chassis ID board holder Ê Disconnect the chassis ID board cab le from the baseboard (1) and open the cable clamp (2). Ê Press the plastic tongues of the chassis ID holder sl ightly inward as indicated b y the arrows (3). Ê Slide the chassis ID board holder outw ar d (4). 1 / 1 1 0 2[...]

310 Maintenance Manual RX900 S1 Cables 15.3.4 Disconnectin g the chassis ID board cab l e Figure 200: Removing the connector clamp Ê Remov e the connector clamp . Figure 201: Disconnect ing the chassis ID board cable Ê Disconnect the chassis ID board cable from the chassis ID board.[...]

RX900 S1 Maintenance Manual 311 Cables 15.3.5 Connecting the ch as sis ID boar d cab le Figure 202: Connecting the chassis ID board cable Ê Connect the chassis ID board cable to the chass is ID board. Figure 203: Installing the connector clamp Ê Install the connector c lamp .[...]

312 Maintenance Manual RX900 S1 Cables 15.3.6 Inst all ing the chass is ID bo ard Figure 204: Installing the chassis ID board holder Ê Press the plastic tongues of the chassis ID hold er slightly inward as indicated b y the arrows (1) and slide the chassis ID board holder inw ard until it cl ick s into place (2). Ê Connect the chassis ID board ca[...]

RX900 S1 Maintenance Manual 313 Cables Figure 205: Connecting the chassis ID board cable Ê Connect the chassis ID board cable (1). Ê Slide the local service displa y inward until i t clic ks into place (2). I In order to enable ServerVie w Operations Manager and Ser verVie w Installation Manager to identify the system, it is necessary to program [...]

314 Maintenance Manual RX900 S1 Cables 15.3.7 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. "Inser ting the CPUMEMR in the slot" on page 186 2. "Closing the server" on page 47 3. "Mounting the server in the rac k" on page 49 4. "Bringing the ser ver bac k to operation" o[...]

RX900 S1 Maintenance Manual 315 Cables 15.4 Replacing po wer cab les of the optical drive, the SAS bac kpl ane, or the power distribution boar d 15.4.1 Required tools ● Star ting and completing the task: – ke y for the rac k doors (if applicable) – Phillips Ph2 scre w dr iver ● Replacing the po wer cables of the optical drive , the SAS bac [...]

316 Maintenance Manual RX900 S1 Cables 6. Remov e all PSUs, see "Remo ving the power supply unit" on page 58 7. Remov e all CPUMEMRs, see "Remo ving the CPUMEMR" on page 190 I Bef or e remo v ing the CPUMEMRs, take a note on the installati on slot number f or each CPUMEMR. Make sure that you re install the CPUMEMR in the slot it[...]

RX900 S1 Maintenance Manual 317 Cables 15.4.4 Disconnecting the cables Figure 207: Disconnecting t he cables from the baseboard Ê Disconnect the f ollowing cables from the baseboard: – SAS bac kplane cable (1) – Signalling cabl e ( 2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5) – Co[...]

318 Maintenance Manual RX900 S1 Cables 15.4.5 Removing the fa n cage Figure 208: Removing the f an cage Ê Loosen the captiv e screws (1). Ê Lift the f an cage out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 319 Cables 15.4.6 Remo ving the CPUMEMR guide Figure 209: Removing the CPUMEMR guide Ê Loosen the captiv e screws of the CPUMEMR gui de (1). Ê Lift the CPUMEMR guide out of the chassis (2). / / 0[...]

320 Maintenance Manual RX900 S1 Cables 15.4.7 Remo ving the air guide Figure 210: Removing the air guide Ê Loosen the captiv e screws (1). Ê Lift the air guide out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 321 Cables 15.4.8 Remo ving the baseboard Figure 211: Removing the baseboard Ê Loosen the captive s c rews (1). Ê Slide the baseboard appro ximately 1 cm in the direction of the arrow (2). V CA UTION! Make su re that you ha ve remov ed all power supply units bef ore removing the baseboard. Otherwise, the po wer supply [...]

322 Maintenance Manual RX900 S1 Cables 15.4.9 Remo ving the power distribution boar d Figure 212: Removing the po wer distribution board Ê Open the cable c lamps (1). Ê Disconnect the pow er distribution cab les from the baseboard (2). Ê Loosen the captiv e screws (3). Ê Remov e the power distribution board from the baseboard. / / 0 0 1 1 2[...]

RX900 S1 Maintenance Manual 323 Cables 15.4.10 Disconnecting the de fective power distrib ution cab le(s) Figure 213: Disconnecting power distributi on cables Ê Select the def ective cabl e(s) and disconnect it/them from the pow er distribution board: – power cab le of the optical dr ive (1, 2) – pow er cable f or the SAS backplane (3) – pow[...]

324 Maintenance Manual RX900 S1 Cables 15.4.11 Connecting the new po wer distribution cab le(s) Figure 214: Connecting pow er dist ribution cab les Ê Connect the new c able(s) to the po wer distribution board: – power dis tr ibution cab les (1) – pow er cable f or the SAS backplane (2) – power cab le of the optical drive (3, 4) 1 2 / / 0 1[...]

RX900 S1 Maintenance Manual 325 Cables 15.4.12 Installing the po wer distribution board Figure 215: Installing the power dist ribution board Ê Inser t the power distributi on board in the baseboard (1). Ê Connect the pow er distribution cab les to the baseboard (2). Ê F asten the captiv e screws (3). Ê Close the cab le clamps (4). / 0 0 1 1 2 2[...]

326 Maintenance Manual RX900 S1 Cables 15.4.13 Ins erti ng the baseboard Figure 216: Inser ting the baseboard Ê Carefully low er the baseboard in the chassis b y using the handle (1). Ê Slide the baseboard in the dire ction of the arrow (2) until it clic ks into place. Ê F asten the captive scre ws (3). V CA UTION! Ensure not to damage the EMI s[...]

RX900 S1 Maintenance Manual 327 Cables 15.4.14 Installing the air guide Figure 217: Installing the air gui de Ê Place the air guide in th e chassis (1). Ê F asten the captiv e screws (2). / 0 0[...]

328 Maintenance Manual RX900 S1 Cables 15.4.15 Inser ting the CPUMEMR guide Figure 218: Inserting the CPUME MR guide Ê Inser t the CPUMEMR guide in the installation s lot (1). Ê F asten the captiv e screws of the CPUMEMR guid e ( 2). 0 0 /[...]

RX900 S1 Maintenance Manual 329 Cables 15.4.16 Inserti ng the fan cage Figure 219: Inser ting t he fan cage Ê Inser t the f an cage in the mounting ba y (1). Ê F asten the captiv e screws (2). / 0 0[...]

330 Maintenance Manual RX900 S1 Cables 15.4.17 Connecting the ca bles to the baseboard Figure 220: Connecting the cab l es to the baseboard Ê Connect the f ollowing cables to the baseboard: – SAS backpl ane cable (1) – Signalling cab le (2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5) [...]

RX900 S1 Maintenance Manual 331 Cables 15.4.18 Sliding the local service displa y inward Figure 221: Sliding the local service displa y inward Ê Slide the local ser vice displa y inwa rd until it clic ks into place. 15.4.19 Completing the task Ê P erform the f ollowing procedures to complete the task: 1. Install the BBU holder , see "Expansi[...]

332 Maintenance Manual RX900 S1 Cables 6. "Closing the server" on page 47 7. "Mounting the server in the rac k" on page 49 8. "Bringing the ser ver bac k to operation" on page 51 9. "Closing the rac k door" on page 51 Ê V er ify the settings on the baseboard, see the "Basebo ar d D3081, CPUMEMR D3131, P[...]

RX900 S1 Maintenance Manual 333 Cables 15.5 Replacing the SAS cable, the SA T A cable, the fr ont video connector cable, or the fr ont USB cable I The baseboard is optionally equipped wi th a T r usted Platf or m Module (TPM). This module enables programs from third par ty manuf acturers to store ke y information, f or example drive enc r yption us[...]

334 Maintenance Manual RX900 S1 Cables 15.5. 2 Star ting the task Ê P erf or m the f ollowing procedures: 1. "Opening the rac k door" on page 40 2. "Locate the f aulty ser ver" on page 37 3. "Shutting down the s er ver" on page 41 4. "Sliding the server out of the rack " on page 42 5. "Opening the serve[...]

RX900 S1 Maintenance Manual 335 Cables 15.5.3 Sliding the local service dis pla y outwar d Figure 222: Sliding the local service displa y out ward Ê Unloc k the local s er vice displa y (1). Ê Slide the local service displa y outward a fe w centimeters so that you ha v e free access (2). / 0[...]

336 Maintenance Manual RX900 S1 Cables 15.5.4 Disconnecting the cables Figure 223: Disconnecting t he ca bles from the baseboard Ê Disconnect the f ollowing cab les from the bas eboard: – SAS backpl ane cable (1) – Signalling cab le (2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5) – [...]

RX900 S1 Maintenance Manual 337 Cables 15.5.5 Removing the fan cag e Figure 224: Removing the f a n cage Ê Loosen the captive s c rews (1). Ê Lift the f an cage out of the chassis (2) . / / 0[...]

338 Maintenance Manual RX900 S1 Cables 15.5.6 Remo ving the CPUMEMR guide Figure 225: Removing the CPUMEMR guide Ê Loosen the captiv e scre ws of the CPUMEMR guide (1). Ê Lift the CPUMEMR guide out of the chassis (2). / / 0[...]

RX900 S1 Maintenance Manual 339 Cables 15.5.7 Remo ving the air guide Figure 226: Removing the air gui de Ê Loosen the captive s c rews (1). Ê Lift the air guide out of the chassis (2). / / 0[...]

340 Maintenance Manual RX900 S1 Cables 15.5.8 Remo ving the basebo ard Figure 227: Removing the baseboard Ê Loosen the captiv e screws (1). Ê Slide the baseboard appro ximately 1 cm in the direction of the arrow (2). V CA UTION! Make s ure that you ha ve remo ved al l pow er supply units bef or e removing the baseboard. Otherwise , the power supp[...]

RX900 S1 Maintenance Manual 341 Cables 15.5.9 Opening the cable gui des For the SAS cable, the SA T A cable, the front video conn ector cable, or the front USB cable Figure 228: Opening the front connectors cab le guide Ê Remo v e the scre ws (see cir cles). Ê Open the cab le guide. Ê Select the cabl e to be remov ed: – F ront USB cable (1) ?[...]

342 Maintenance Manual RX900 S1 Cables For the SAS cable Figure 229: Opening the SAS cabl e guide Ê Remov e the screws (see circles). Ê Open the cab le guide. Ê Open the cab le clamps and remov e the defec tive S AS cabl e. 15.5.10 Closing the cable guides For the SAS cable, the SA T A cable, the front video conn ector cable, or the front USB ca[...]

RX900 S1 Maintenance Manual 343 Cables For the SAS cable Figure 231: Clos ing the SAS cable guide Ê Inser t the new cab l e and close the cab le clamps. Ê Close the cab le guide and f asten the screws (see circles). 15.5.11 Inserti ng the baseboard Figure 232: Inser ting t he baseboard 0 / 1 1[...]

344 Maintenance Manual RX900 S1 Cables Ê Carefully low er the baseboard in the chassis b y using the handle (1). Ê Slide the baseboard in the dire ction of the arrow (2) until it clic ks into place. Ê F asten the captive scre ws (3). V CA UTION! Ensure not to damage the EMI springs to comply with applic able EMC regulations and satisfy cooli ng [...]

RX900 S1 Maintenance Manual 345 Cables 15.5.13 Inser ting the CPUMEMR guide Figure 234: Inser ting t he CPUMEMR guide Ê Inser t the CPUMEMR guide in the installa tion s lot (1). Ê F asten the captiv e screws of the CPUM EMR guide (2). 0 0 /[...]

346 Maintenance Manual RX900 S1 Cables 15.5.14 Ins erti ng the fan cage Figure 235: Inser ting the fan cage Ê Inser t the f an cage in the mounting ba y (1). Ê F asten the captive scre ws (2). / 0 0[...]

RX900 S1 Maintenance Manual 347 Cables 15.5.15 Connecting the cab les to the baseboard Figure 236: Connecting the cables to the base board Ê Connect the f ollowing cab l es to the baseboard: – SAS bac kplane cable (1) – Signalling cabl e ( 2) and power cab le (3) to the optical drive – F ront video connector cable (4) – F ront USB cable (5[...]

348 Maintenance Manual RX900 S1 Cables 15.5.1 6 Sliding the l o cal service di splay inwar d Figure 237: Sliding the local s ervice display inward Ê Slide the local service display i nward until it click s into place . 15.5.17 Completing the task Ê P erf or m the f ollowing procedures to complete the task: 1. Install the BB U holder , see "E[...]

RX900 S1 Maintenance Manual 349 Cables 6. "Closing the server" on page 47 7. "Mounting the server in the rac k" on page 49 8. "Bringing the ser ver bac k to operation" on page 51 9. "Closing the rac k door" on page 51 Ê V er ify the settings on the baseboard, see the "Baseboard D3081, CPUMEMR D3131, PCI[...]

350 Maintenance Manual RX900 S1 Cables[...]

RX900 S1 Maintenance Manual 351 16 Appendix 16.1 Mechanic al o verview 16.1.1 Fr ont side Figure 238: RX900 S1 front side F or detailed inf or mation on connectors see "PRIMERGY RX900 S1 Server - Operating man ual". P os. Com ponent P os. Component 1 Hard disk drives / dumm y modules #0 - #7, see figure 239 5 Control panel 2 ID card 6 Vid[...]

352 Maintenance Manual RX900 S1 Appe ndix Figure 239: HDD/SSD bay numbering sc heme 16.1.2 Rear side Figure 240: RX900 S 1 rear side P os. Component P os. C omponent 1 PCI Riser (PCIR); PCIe slots #1 - #7, see figure 244 7 Serial connector 2 4x USB connectors 8 Video connector 3 2x 10 Gbit/s LAN connec tors 9 Modular RAID controller (PCIe slot #8),[...]

RX900 S1 Maintenance Manual 353 Appendix F or detailed inf or mation on connectors see "PRIMERGY RX900 S1 Server - Operating man ual". Figure 241: P ower supply unit n umbering scheme 5 P ower Suppl y Units (PSU) #1 - #4, see figure 241 11 PCIe slots #13 - #17, see figure 244 6 Management LAN connector P os. Com ponent Pos. Component / 0 [...]

354 Maintenance Manual RX900 S1 Appe ndix 16.1.3 T op vie w Figure 242: T op view P os. Compon ent Pos. Component 1 F an #1 - #4, see figure 243 7 Modular RAID controller (PCIe slot #8), see figure 244 2 IOH #1 - #4 (underneath the f an) 8 Hot-plug PCIe slots #9 - #12 (from bottom to top), see figure 244 3 CPUMEMRs #1 - #8 (from bottom to top), see[...]

RX900 S1 Maintenance Manual 355 Appendix Figure 243: Fan numbering scheme Figure 244: PCIe slot assignment Figure 244 shows the PCIe slot configurati on. Expansion cards can be installed in the PCIe slots on the PCI Riser (A) and on the baseboard (D). The PCI Riser is connected to the baseboard via the connectors C and E. / 0 1 2     ?[...]

356 Maintenance Manual RX900 S1 Appe ndix The PCIe slots are assigned as f ollows: ● B: non-hot plug PCIe slots on the PCI Riser ● F: non-hot plug PCIe slot for the Modular Raid controller only ● G: hot-plug PCIe slots ● H: non-hot plug PCIe slots on the baseboard Figure 245: CPUMEMR numbering scheme / 2 1 4 0 6 3 5[...]

RX900 S1 Maintenance Manual 357 Appendix Figure 246: DIMM slot numbering scheme C B C A C C C D B 1C 1D 1E 1F 1G 1H 1 A 1B B 2C 2D 2E 2F 2G 2H 2 A 2B[...]

358 Maintenance Manual RX900 S1 Appe ndix 16.2 Mounting or d er f or SSD and HDD mod ules Basic rules f or the mounting order of solid state drives and hard disk driv es: 1. If solid state driv es and hard disk dr iv es are to be installed, the solid state drives are ins talled first. 2. Solid state driv es with diff erent capacities are installed [...]

RX900 S1 Maintenance Manual 359 Appendix 16.3 Memor y board configuration Basic rules f or the population order of DIMM memory modules: ● DIMM memory modules with different capacit ies are installed from highest to lowes t capacity . ● Subdivide the total number of DIMM memory modules such that the same multiple of f our modules is placed on ea[...]

360 Maintenance Manual RX900 S1 Appe ndix CP U#3 0 -- -- -- -- -- - - - - -- -- - - -- -- #2 1 x -- -- -- x -- -- -- x -- -- -- 2 x x - -- -x x - -- - x x - - - - 3 xxx- - xxx- - xx x - - 4 xxxxxxx x xx x x CP U#4 0 -- -- -- -- -- - - - - -- -- - - -- -- #2 1 x -- -- -- x -- -- -- x -- -- -- 2 x x - -- -x x - -- - x x - - - - 3 xxx- - xxx- - xx x -[...]

RX900 S1 Maintenance Manual 361 Appendix CPU#8 0 -- -- -- -- -- -- -- -- -- -- -- -- #4 1 - -- -- -- - - -- -- - - - x - - - - - - 2 - -- -- -- - - -- -- - - - x x - - - - 3 - -- -- -- - - -- -- - - - x x x - - 4 - -- -- -- - - -- -- - - - x x x x CPU No. DIMM slo t pop. order 4 CPUMEMRs 6 CPUMEMRs 8 CPUMEMRs IOH No. 1B 1D 1F 1H 1A 1C 1E 1G 2B 2D 2[...]

362 Maintenance Manual RX900 S1 Appe ndix 16.4 PCIe slot to CPUMEMR a ssignment Figure 248 shows the assignment of PCIe slots to the 4 I/O Hubs and the 4 - 8 CPUMEMRs. I Bef ore adding an e xpansion card, chec k carefully whether this PCIe slot is suppor ted with the CPUMEMR confi guration of the indiv i dual ser v er. Figure 248: Assignment of PCI[...]

RX900 S1 Maintenance Manual 363 Appendix CPU populatio n order CPU - IOH mapping Connected devi ce s Remark 4 CPUs 6 CPUs 8 CPUs C PU No. IOH No. CPU#1 x x x #1 or #2 #1 ICH10 P CIe #5 to BMC CPU#2 x x x BMC (V G A) GbE#1, GbE#2, GbE#3, 10GbE#1 PCIe slot #8 Modular RAID PCIe slot #1 PCI Riser PCIe slot #2 PCI Riser CPU#3 x x x #3 or #4 #2 PCIe slot[...]

364 Maintenance Manual RX900 S1 Appe ndix 16.5 Expansion card configuration table Expansion cards require I/O s pace f or Legacy Booting and f or OS running. Due to the limitati on of I/O space, see "Bas eboard D3081, CPUMEMR D3131, PCIR D3082 f or PRIMERGY RX900 S1 T echnical Manual", the basic rules f or installing e xpansion cards are:[...]

RX900 S1 Maintenance Manual 365 Appendix Intel GbEx1 Gen 1x4 8 x x x x x x G b E x 2 G e n 1 x 4 8 xx xx xx GbEx4 Gen 1x4 8 (*2) (*2) x x x x 10GbEx2 Gen 2x8 8 x x x x x x Chipset IOH#3 IOH#4 Bus scan order 12 11 10 9 17 16 15 14 13 I/O space assigning order within the I/O Hub (IOH) 12 12 H o t - p l u g y y y y nnnnn G e n 2 w i d t h x 8x 8x 8x 8[...]

366 Maintenance Manual RX900 S1 Appe ndix *1) The SAS RAID controller shall not be i nstalled in PCIe slot #1 to #7 on the PCI Riser when a BBU is connected because of l imited length of the BBU cab le. *2) The Quad LAN card consumes twice as much I/O space as a standard e xpansion card because it includes a bridge within the card. If you i nstall [...]

RX900 S1 Maintenance Manual 367 Appendix 16.6 Cab ling Figure 249: Cabling plan of RX900 S 1 S ATA S A S Pow e r Key : Gro u nd U S B S ign a l B as e b o a rd D 3 0 8 1 Control p a nel S A S B a ckpl a ne P ower Di s tri bu tion Bo a rd CA072 3 6-G002 F ront U S B Loc a l s ervice di s pl a y ID_TEMP F ront VG A BBU 0- 3 4-7 Mod u l a r RAID Optic[...]

368 Maintenance Manual RX900 S1 Appe ndix[...]