Haier HWM90-0713S manuale d’uso

User's manual This manual is for HWM90-0713S Please read this manual carefully before using. Retain it for future reference. T win-tub Washing Machine with Pump[...]

Contents Names of the parts - - - - - - - - - - - - - - - - - 1 Safety precautions - - - - - - - - - - - - - - - - - 2 Installation and adjustment - - - - - - - - - - - 4 Preparation before washing - - - - - - - - - - 6 The musts in washing - - - - - - - - - - - - - - - 7 Usage of the detergent - - - - - - - - - - - - - 7 Washing sequence - - - - -[...]

1 Meaning and description of the symbols Warning sign Forbidding sign Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents, otherwise it may cause damage of the machine or injure the personal safety of the user . Contents marked with that [...]

Safety precautions Please insert the power cord into special receptacle with rated vol- tage. Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably. If possible, please adopt electric leakage protector. When the machine is normally using, please put the power plug at the location easily [...]

Please don t use the washer in the environment below 0 C. If the washer is below 0 C, the washer s water inlet system and draining system will be frozen ,then result in the damaged of the whole machine. If the washer has below 0 C, please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use . It is suggested [...]

Installa tion and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the overflow filter of the wash tub. See to th[...]

5 How to change the direction of the drain hoses Install the water inlet hose; Select the water level Insert the water inlet hose into the water-filling entrance on the control pane directly.(pull it out to dismantle it) Select water level according to the quantity of the laundries. Set the water level adjusting lever to needed line. Wa ter inlet h[...]

Pr eparation bef or e washing 6 Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Hang the drain hose up to suitable position . 4.Slanting or uneven ground may resu[...]

The musts in washing 7 The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The thickness ,size , type of the cloth will influ- ence the actual washing ca[...]

Washing sequence 8 Figure 3 Spin timer Was h timer (T o set to below 2 minute, first set to 6 minute then turn it back. it can increase the service life of the timer). (to set to below 1 minute, first set to 2 minute then turn it back. it can increase the service life of the timer). W ash Figure 2 Figure 1 Wat er inlet SPIN TIMER WASH TIMER WASH SE[...]

9 Rinse with stored water Rinse with water-filling 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is a few , please use "Standard" current. If you use "Strong"[...]

T o do spinning and draining together, please first do spinning for around 1 minute, then do draining . Otherwise the spinning will stop owing to too much water stored in the spin tub. In spinning, it will pause the work if you open the outer cover of the spin tub. Close it to resume the spinning. 10 Ï´µÓÐëÖª Spinning Outer cover of The spi[...]

11 After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. 1 T ake off the overflow filter. As indicated in the figure, nip the elastic fixing claw and pull it to the direction[...]

12 Cleaning the overflow filter 2. T ake off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. 4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounti[...]

13 Wipe the complete unit with soft cloth twisted dry. Wipe with neutral detergent if too dirty. Do not wash it directly by water. After washing, dismount the water inlet hose. Do not store water in the tub for long period. Discharge the water immediately after each using. Pull off the power plug and hang up the power cord. Hang up the drain hose. [...]

14 T ro uble-shooting Ans wer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.[...]

15 W ater inlet hose Gland Lint filter Packing list Twin-tub washing machine with pump Name Quantity User's manual One piece One piece One piece One piece One set[...]

16 Specification W ater level/Water quantity (L) (about) Maximum/48 Medium/39 Minimum/33 Injection pressure(MPa ) 0.02 0.2 Wa shing capacity(kg) 9.0[...]