Hearth and Home Technologies 6000GL-IPI-R manuale d’uso

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 1 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. - [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: ___[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous s[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 4  = Contains updated information. 13 Finishing A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 50 B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 C. Doors . . . . . . . . . . . . . . . . . . . . . . .[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 5 B. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 6 B. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materi[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 7 C. BTU Speci fi cations This product is listed to ANSI standards for “V ented Gas Appliance Heaters” and applicable sections of “Gas Burn- ing Heating Appliances for Manufactured Homes and Recreational V ehicles”, and “Gas Fired Appliances for Use at High Alti[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth an[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 9 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . DECORA TIVE DOORS (NOT [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 10 D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figur[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 1 1 I. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer . 1. Turn off all electric power to the appliance. 2. This appliance[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 12 J. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.H. • Clean fi xed glass as[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid a[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 14 V enting Frequency: Seasonally By: Homeowner T ools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow , debris, etc. • V erify termination cap clearance to subsequent[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 15 Figure 3.1 IPI Pilot Flame Patterns[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 16 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4.1 T ypical System CEILING FIRESTOP O[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 17 B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Install[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 18 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 19 B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: T reatment of ceiling fi restops and wall shield fi restops[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 20 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, e[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 21 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 ......................................[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 22 O N P R Q V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 6.3 Minimum Clearances for T ermination A = 12 inches................. clearances above grade, ver anda, porch, deck or balcony B = 12 inches................. clearances to w[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 23 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP or SLP venting systems. Refer to Sec- tion 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers. The pipe is tested [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 24 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 H 1 V 1 Figure 7.3 Figure 7.4 T op V ent - Horizontal T ermination T op V ent - Horizontal T ermination One Elbow T wo Elbows Note: For corner installations: A 6 inch (152 mm) section of straight pipe may need to be attached to the [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 25 Figure 7.5 T op V ent - Horizontal T ermination - (continued) Three Elbows H 2 H 1 V 2 V 1 V 1 Min. H 1 Max. V 2 Min. H 2 Max. Elbow only 2 ft. 610 mm 0 in. 0 mm 1 ft. 305 mm 6 in. 152 mm 3 ft 914 mm 6 in. 152 mm 2 ft. 610 mm 1 ft. 305 mm 6 ft. 1.8 m 1 ft. 305 mm 6 ft. [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 26 T op V ent - V ertical T ermination No Elbow Figure 7.6 Note: If installing a vertical vent/ termination off the top of the ap- pliance, the fl ue restrictor should be used. V 1 V 1 = 40 ft. Max. (12.4 m) V 1 = 3 ft. Min. (914 mm) Figure 7.8 Flue Restrictor 2. Break th[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 27 H 1 V 1 V 2 T op V ent - V ertical T ermination (continued) Figure 7.1 1 T wo Elbows Figure 7.10 4. Center the Flue Restrictor on vent and secure in place by using two self-tapping screws (see Figure 7.10). 5. Reinstall the Exhaust Shield. 3. Match the amount of vertica[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 28 Figure 7.12 T op V ent - V ertical T ermination - (continued) Three Elbows INST ALLED HORIZONT ALL Y H 1 H 2 V 1 V 2 V 1 H 1 + H 2 V 2 V 1 + V 2 Minimum H 1 + H 2 Maximum Elbow only 1 ft. 305 mm * * * 1 ft. 305 mm 6 in. 152 mm 2 ft. 610 mm * * * 2 ft. 610 mm 1 ft. 305 m[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 29 Rear V ent - Horizontal T ermination Figure 7.13 Figure 7.14 No Elbow One 45º Elbow H 1 H 1 H 1 = 16 in. (406 mm) Maximum Do not use a 45º elbow in corner installations. Use two 90º elbows instead.[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 30 INSTALLED HORIZONTALLY H 3 H 1 H 2 V 1 Rear V ent - Horizontal T ermination - (continued) T wo Elbows Figure 7.15 Figure 7.16 Three Elbows H 1 H 2 V 1 H 1 Maximum V 1 Minimum H 2 H 1 + H 2 Maximum 1 ft. 305 mm Back to Back 90º Elbows 1 ft. 305 mm 2 ft. 610 mm 2 ft. 610[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 31 Rear V ent - V ertical T ermination One Elbow Figure 7.17 T wo Elbows Figure 7.18 H 1 V 1 INST ALL ED HORIZONT ALL Y H 1 H 2 V 2 V 1 Minimum H 1 Maximum 6 in. 152 mm 2 ft. 610 mm 1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 7 ft. 2.1 m 4 ft. 1.2 m 8 f[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 32 Rear V ent - V ertical T ermination - (continued) Three Elbows Figure 7.19 Three Elbows Figure 7.20 INST ALLED HORIZONT ALL Y H 3 H 1 H 2 V 1 V 2 V 1 H 2 H 1 H 1 H 2 H 3 V 1 Minimum H 1 + H 2 + H 3 Maximum *** 8 ft. 2.4 m 6 ft. 1.8 m *** 9 ft. 2.7 m 7 ft. 2.1 m *** 10 f[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 33 A* B* 10 in. 12 in. C D 10 in. 10 in. A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops • Around vent syste[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 34 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 8.3). • SLP pipe only - Frame opening 9 [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 35 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constr[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 36 A. Choosing the T op or Rear V ent CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 37 B. Rear V ent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. Figure 9.6 Remove the insulation from the outer vent pipe. For rear venting there is no insulation in the outer vent pipe. Figure 9.7 T o attach the fi rst sec[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 38 1 0 10 Inst alli ng V ent Pi pe (D VP and SLP P ipe ) A. Assemble V ent Sections (DVP Pipe Only) Attach V ent to the Firebox Assembly Note: The end of t he pipe secti ons with the lanc ed tabs wi ll face toward the applianc e. Attach the fi rst pipe section to the star[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 39 B. Assemble V ent Sections (SLP Pipe Only) T o attach the fi rst vent component to the starting collars of the appliance: • Attach a DVP-2SL or DVP-SLP24 adapter to the starting collar of the appliance. • Lock the vent components into place by sliding the pipe sect[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 40 120º Figure 10.8 Securing V ertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.1 1. • Pull carefully[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 41 F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a fl at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the fi restop. • Seal the gap between the vent pipe and fi restop [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 42 G. Install Metal Roof Flashing Note : Skip this section if using the RF4-8. • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending t[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 43 I. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar (Sections 10.G. and 10.H.) Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Section 10.D. Secure [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 44 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.23 Figure 10.23 TERMINA TION CAP J. Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 45 Figure 10.25 Venting through the wall INTERIOR HEA T SHIELD OR EXTENDED HEA T SHIELD W ALL SHIELD FIRESTOP HEA T SHIELD 1-1/2 IN. (38 MM) MIN. OVERLAP SHEA THING VENT DEPTH FROM BACK OF APPLIANCE T O OUTSIDE SURF ACE OF EXTERIOR WA LL (SEE CHART BELOW) SLIP SECTION CAN [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 46 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performance[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 47 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code CSA C22.1. • Wire the applia[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 48 D. Electrical Service and Repair W ARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls. Wiring errors can cause improper and dangerous operation. V erify proper operation after servicing. Figure 12.2 Intelli fi re Pilot Ignition (IPI[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 49 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5): • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 50 1 3 13 Fi nishing A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materi- als (i.e., steel studs, concrete board, etc.)[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 51 C. Doors Only doors certi fi ed for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. Once you have determined what kind of door and fi nishing material is going to be used on the fi replace, you may use the table be[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 52 A. Remove Fixed Glass Assembly See Section 14.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the contr[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 53 F . Ember Placement W ARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually . Improperly placed embers interfere with proper burner operation. Ember material is shipped w[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 54 G. Install the Log Assembly Log Assembly: LOGS-6000GL STEP 2. Place the metal grate on top of the burner . Position the legs of the grate into the forward set of indentations in the burner top. The grate should not cover any ports in the burner . STEP 1. CAUTION: Logs a[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 55 Figure 14.1 1 T op View STEP 5. Log #3 (SR V2102-105): Place log #3 on top of the burner surface in front of the hump. The bottom of the log is contoured to match some of the burner surface features. Slide it back against the hump. The “V” shaped notch in the front [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 56 K. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.19. • Loo[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 57 A. Intelli fi re Ignition System Symptom Possible Cause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. A. Incorrect wiring. V erify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct t[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 58 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occur[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 59 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only . For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions A D B C H ELECTRICAL ACC ESS G F E GAS LINE ACC ESS [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 60 B. V ent Components Diagrams Figure 16.2 DVP vent components 10-1/2 in. (267 mm) 10-7/8 in. (276 mm) 45 ° 7-3/8 in. (187 mm) 11-3/8 in. (289 mm) 1-1/4 in. (32 mm) 9-1/4 in. (235 mm) 13-1/4 in. (337 mm) 1/2 in. TYP DVP90ST (90° Elbow) 10 in. (254 mm) 10 in. (254 mm) 1 [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 61 DVP-HPC1 DVP-HPC2 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 62 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK Trap Ca p Brick Extension 13-3/4 in. (349 mm) 5 in. (127 mm) 13-3/4 in. (349 mm) Cap Shield[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 63 DVP-TB1 BasementVent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 7-1/4 in. 12 in. 305 mm (184 mm) 5-1/4 in. (133 mm) 12-1/2 in. (318 mm) DVP-TVHW VerticalTermination Cap (Highwind) PVK-80 (For use with IPI and DSI applian[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 64 B. V ent Components Diagrams (continued) DVP-HRC-SS DVP-HRC-ZC-SS HORIZONT AL TERMINA TION CAP 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm 5-1/2 in. 140 mm 8-3/8 in. 21[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 65 B. V ent Components Diagrams (continued) Figure 16.7 SLP Series V ent Components Effective Height/Length Pipe inches mm SLP4 4 102 SLP6 6 152 SLP12 12 305 SLP24 24 610 SLP36 36 914 SLP48 48 1219 SLP6A 2 - 6 51 - 152 SLP12A 2 - 12 51 - 305 8-3/4 in. 222 mm 6-1/2 in. 165 [...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 66 B. V ent Components Diagrams (continued) Figure 16.8 SLP Series V ent Components SLP-SNKD Snorkel T ermination Cap SLP-TVHW V ertical T ermination Cap SLP-CCS-BK Cathedral Ceiling Support Box-Black SLP-DCF-BK Ceiling Firestop Black SLP-WT -BK W all Thimble-Black SLP-TRA[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 67 C. Service Parts Part number list on following page. Service Parts Diagram 1 4 6 5 3 2 Log Set Assembly 10 11 8 7 9 12 Beginning Manufacturing Date: May 2006 Ending Manufacturing Date: ______ 6000GL-IPI-R, -S[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 68 Service Parts List IMPORT ANT :THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM D[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 69 Service Parts V alve Assembly Diagram/ Parts List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Beginning Manufacturing Date: May 2006 Ending Manufacturing Date: ______ 6000GL-IPI-R,-S IMPORT ANT :THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your app[...]

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev . O • 12/08 70 D. Contact Information - NOTES - ________________________________________________________________________________ ________________________________________________________________________________ ___________________________________________________________________________[...]