Hearth and Home Technologies SL-550TR-D manuale d’uso

1 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Models: SL-550TR-D SL-750TR-D SL-950TR-D Owner ’ s Manual Installation and Operation • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: ____________________ Dealership pu[...]

3 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Î - T able of Contents - Section 1: Listing and Code Approvals A. Appliance Certi fi cation ................................... 4 B. Glass Speci fi cations ...................................... 4 C. BTU Speci fi cations ........................................ 4[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 4 Listing and Code Approvals C. BTU Speci fi cations 1 MODELS: SL-550TR-D, SL-750TR-D, SL-950TR-D LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2002 • CSA2.33-M02 • UL307B A. Appliance Certi fi catio[...]

5 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 G. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealt[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 6 A. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Gett[...]

7 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 I B G H C A D E F In addition to these framing dimensions, also reference the following sections: • Clearances and Mantel Projections (Section 3.C and 3.D) • V ent Clearances and Framing (Section 6). 3 Framing and Clearances NOTE: • Illustrations re fl ect typ[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 8 Figure 3.2 Clearances to Combustibles C B D A E H I F FROM TOP OF HOOD TO CEILING G J B. Constructing the Appliance Chase A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. V ertical vents that run on the outside of a b[...]

9 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 D. Mantel Projections 1 ” 2 ” Note: Clearance from opening to perpendicular wall. Figure 3.3 Clearances to Mantels or other Combustibles above Appliance Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 10 A. V ent T ermination Minimum Clearances Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as speci fi ed. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fi[...]

11 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 4.4 Minimum Clearances for T ermination A = 12 inches ............... clearances above grade, ver anda, porch, deck or balcony B = 12 inches ............... clearances to window or[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 12 5 V ent Information and Diagrams Fire Hazard. Explosion Risk. Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue serving a separate solid-fuel or gas burning appliance. • V ent this appliance directly outside. • Use separate vent system for[...]

13 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 3i n .C L E A R A N C E TERMINA TION CAP FL EX -V ENT 1i n . CLEAR AN CE D. Use of Flex V ent The fl ex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports. A support is required at [...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 14 Figure 5.4 E. V ent Diagrams T op V ent - Horizontal T ermination V enting with 1 elbow (NG) H 1 V 1 V Minimum H 1 Maximum SL-550TR-D SL-750TR-D SL-950TR-D 90 Elbow 2 ft. 610 mm 2 ft. 610 mm 1 ft. 305 mm 0.5 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm 2 ft. 610 mm 1.5 ft. [...]

15 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 H 2 H 1 V 1 Figure 5.5 T op V ent - Horizontal T ermination V enting with 2 elbows (NG) V Minimum H 1 + H 2 Maximum SL-550TR-D SL-750TR-D SL-950TR-D 90 Elbow 0.5 ft. 152 mm 0.5 ft. 152 mm 0 ft. 0 mm 0.5 ft. 152 mm 1 ft. 305 mm 1 ft. 305 mm 1 ft. 305 mm 1.5 ft. 457 m[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 16 Figure 5.6 H 2 V 2 H 1 V 1 T op V ent - Horizontal T ermination V enting with 3 elbows (NG) V Minimum H 1 + H 2 Maximum SL-550TR-D SL-750TR-D SL-950TR-D 90 Elbow 2 ft. 610 mm 2 ft. 610 mm 2 ft. 610 mm 0.5 ft. 152 mm 6 ft. 1.8 m 6 ft. 1.8 m 6 ft. 1.8 m 1.5 ft. 457 mm[...]

17 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Figure 5.7 NOTE: If installing a vertical vent/termination off the top of the appliance, the optional vertical termination baf fl e should be used. CAP V 1 V 1 = 44 ft. Max. (13.4 m) T op V ent - V ertical T ermination No Elbows Baf fl e Instruction 1. Install the[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 18 Figure 5.9 V 2 H 1 V 1 T op V ent - V ertical T ermination V enting with 2 elbows (NG) V MIN. SL-550TR-D SL-750TR-D SL-950TR-D H MAX. H MAX. H MAX. V 2 V 1 + V 2 MIN. 90 Elbow 1.5 ft. 457 mm 1.5 ft. 457 mm 1 ft. 305 mm * * 0.5 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm 2 [...]

19 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Figure 5.10 H 2 V 2 H 1 V 1 T op V ent - V ertical T ermination V enting with 3 elbows (NG) V MIN. SL-550TR-D SL-750TR-D SL-950TR-D H MAX. H MAX. H MAX. V 2 V 1 + V 2 MIN. 90 Elbow 0.5 ft. 152 mm 0.5 ft. 152 mm 0 ft. 0 mm * * 0.5 ft. 152 mm 1 ft. 305 mm 1 ft. 305 mm[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 20 Figure 5.12 Figure 5.1 1 H 1 = 28 in. (71 1 mm) Maximum Rear V ent - Horizontal T ermination No Elbows H 1 = 9 in. (229 mm) Maximum Rear V ent - Horizontal T ermination One 45º Elbow For corner installation of models SL-550TR-D and SL-T50TR-D ONL Y Note: Use DVP Se[...]

21 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Note: Use DVP Series components only . Rear V ent - Horizontal T ermination V enting with 2 elbows H 1 MAX. V 1 MIN. H 2 MAX. H 1 + H 2 MAX. 1.5 ft. 457 mm Back to back elbows 1 ft. 305 mm 2.5 ft. 762 mm 3 ft. 914 mm 1 ft. 305 mm 3 ft. 914 mm 6 ft. 1.8 m 5 ft. 1.5 m[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 22 Note: Use DVP Series components only . Note: Use DVP Series components only . Figure 5.15 Figure 5.16 V 1 H 1 V 1 H 2 H 1 INS T A LLED HORIZONT ALL Y Rear V ent - V ertical T ermination V enting with 1 elbow V 1 MIN. H 1 MAX. 1 ft. 305 mm 3.5 ft. 1.1 m 2 ft. 610 mm [...]

23 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 V 1 MIN. H 1 MAX. H 2 MAX. H 1 + H 2 MAX. Back to back elbows 1.5 ft. 457 mm 1 ft. 305 mm 2.5 ft. 762 mm 1 ft. 305 mm 3.5 ft. 1.1 m 2 ft. 610 mm 6.5 ft. 2.0 m 2 ft. 610 mm 5.5 ft. 1.7 m 3 ft. 914 mm 10.5 ft. 3.2 m 3 ft. 914 mm 7.5 ft. 2.3 m 7 ft. 2.1 m 14.5 ft. 4.4 [...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 24 Combustible W all Penetration Frame a hole in a combustible wall for an interior wall shield fi restop, (Figure 6.2) whenever a wall is penetrated. Use same size framing materials as those used in the wall construction. The wall shield fi restop maintains minimum [...]

25 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 C. V ertical Penetration Framing Installing the Ceiling Firestop • Frame an opening 10 inches by 10 inches whenever the vent system pene- trates a ceiling/ fl oor (see Figure 6.4). • Frame the area with the same sized lumber as used in ceiling/ fl oor joist. ?[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 26 A. Choosing the T op or Rear V ent Appliance Preparation 7 Figure 7.2 Cut the seal cap strap across the rectangles next to the disk. The top heat shield may need to be removed to perform this step. Figure 7.3 Remove the white gasket material covering the seal cap. F[...]

27 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Figure 7.7 T o attach the fi rst section of vent pipe, make sure to use the fi berglass gasket in the manual bag to seal between the fi rst vent component and the outer fi replace wrap. Use 2 self tapping screws to secure the gasket to the outer wrap. Secure the[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 28 C. Securing and Leveling the Appliance The diagram shows how to properly position, level, and secure the appliance (see Figure 7.11). Nailing tabs are pro- vided to secure the appliance to the framing members. • Rear venting - refer to V ent Clearances and Framing[...]

29 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 A. Assembly of V ent Sections (DVP Pipe ONL Y) Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 30 Assembling DVP-12A Slip Sections The outer fl ue of the slip section should slide over the outer fl ue of the pipe section and into (inner fl ue) the last pipe section (see Figure 8.6) . Slide together to the desired length, making sure that a 1-1/2 inch outer ?[...]

31 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 B. Disassembly of V ent Sections (DVP Pipe ONL Y) Improper support may allow vent to sag or separate. Securing the V ent Sections V ertical Sections V ertical sections of pipe must be supported every 8 feet after the 25 foot maximum unsupported rise. The vent sup- p[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 32 For V ertical Runs - The vent system must be supported every eight (8) feet (2.4m) above the appliance fl ue outlet by wall brackets. T o install support brackets for vertical runs: • Attach wall brackets to the vent pipe and secure the wall bracket to the framin[...]

33 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 C. Installing Heat Shield and Horizontal T ermination Cap (DVP Pipe ONL Y) NOTE: Where required, an exterior wall fl ashing is available. When penetrating a brick wall, a brick extension kit is available for framing the brick. Heat Shield Requirements for Horizonta[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 34 Installing W all Shield Firestops and Horizontal T ermination Cap (SL Series Pipe ONL Y) Do NOT connect a pipe section to a termination cap without using the telescoping fl ue section found on the termination cap. NOTE: Where required, an exterior wall fl ashing i[...]

35 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 D. Installing Roof Flashing and V ertical T ermination Cap T o install roof fl ashing see Figure 8.16. For installation of vertical termination cap see minimum vent heights for various pitched roofs (see Figure 8.16) . T o attach the vertical termination cap, slide[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 36 Figure 8.18 Assembling the Storm Collar Figure 8.19 Assembling the Storm Collar Around the Pipe Connect both halves of the storm collar with two screws (see Figure 8.18). Wrap the storm collar around the exposed pipe section and align brackets. Insert a bolt (provid[...]

37 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 NOTE: Have the gas supply line installed in accordance with local building codes, if any . If not, follow ANSI 223.1. Installation should be done by a quali fi ed installer approved and/or licensed as required by the locality . (In the Commonwealth of Massachusetts[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 38 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.L. Listed gas appliances are tested and approved without requir[...]

39 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Electrical Information 10 NOTE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code, CSA C221.1 . B. Connecti[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 40 D. Intelli fi re Ignition System W iring This appliance requires a 1 10 V AC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.5. This appliance is equipped with an Intelli fi re control valve which operates on a 3 volt sys[...]

41 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 E. Junction Box Installation F . Wall Switch Installation for Fan (Optional) Figure 10.6 Junction Box Wired to W all Switch If the box is being wired to a wall mounted switch for use with a fan (See Figure 10.6): • The power supply for the appliance must be brough[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 42 A. Mantel Projections Figure 1 1.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. Finishing B. Facing Material 11 Figure 1 1.3 Noncombustible[...]

43 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Appliance Setup 12 A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . C. Accessories Ins[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 44 Log Set Assembly: LOGS-SL550-D D. Positioning the Logs If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately , refer to the following instructions. Carefully remove the logs from the packaging. C[...]

45 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 LOG #3 (SR V2044-703): Place log #3 on the left two grate bars using the notch on the bottom of log #3. Slide the left edge of log #3 forward until it touches the grate. LOG #4 (SR V2044-701): Place log #4 into the tab on log #1. The bottom notch of log #4 should si[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 46 LOG #1 (SR V2045-700): Place log #1 on the grate using the notches in the bottom of the log. Slide log #1 up to the front tabs for NG. Slide it back until top of log touches the back of the fi replace for LP . LOG #2 (SR V530-719): Place log #2 on the right two gra[...]

47 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 LOG #3 (SR V530-718): Place log #3 on the left two grate bars using the notches in the bottom of the log. Position log parallel to log #1 and on the same line as log #2. Left edge of log should rest between grate bar and second tab. LOG #4 (SR V2045-703): Place log [...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 48 Shutter Settings Figure 12.2 Glass Assembly E. Glass Assembly Removing Glass Assembly Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 12.2). Replacing Glass Assembly Replace the glass door o[...]

49 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Operating Instructions 13 CAUTION If installing Intelli fi re ignition battery backup: • Do not install batteries if the backup mode may not be used for extended time. • Batteries may leak. • Install batteries only when needed for power outage. Before operati[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 50 B. Lighting Appliance 1. Turn of f all electric power to the appliance. 2. This appliance is equipped with an ignition device which automatically lights the burner . Do not try to light the burner by hand. 3. W ait fi ve (5) minutes to clear out any gas. Then smell[...]

51 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 1. Turn of f all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Close control access panel. 5. T[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 52 W ARNING C. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuou[...]

53 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 A. Standing Pilot Ignition System T roubleshooting 14 With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service pe[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 54 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter shou[...]

55 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 B. Intelli fi re Ignition System Sympton Possible Cause Corrective Action 1. The ignitor/module makes noise, but no spark. a. Incorrect wiring. V erify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on modul[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 56 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 3. (Continued) Pilot lights but continues to spark, and main burner will not ignite. (If the pilot contin- ues to spark after the pilot fl ame has been lit, fl ame recti fi cati[...]

57 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Maintaining and Servicing Appliance 15 Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance check-up at the beginning of each heating season. Annu[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 58 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary . 3. V erify no obstructions t[...]

59 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Reference Materials 16 A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Fo r framing dimensions and clearances refer to Section 3. Figure 16.1 Appliance Dimensions A B C D E F G H I J K L M N O P Q R S T U V X W Ø G[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 60 B. V ent Components Diagrams Figure 16.2 DVP vent components 10 - 1/ 2 in. (267 mm) 10 - 7/ 8 i n . (276 mm) 45 ° 7- 3 / 8 i n . (187 m m ) 11- 3 / 8 i n . (289 mm) 1 -1/4 in. (32 mm) 9- 1/4 i n. (235 mm) 13 -1/ 4 i n . (337 mm) 1/2 in . T YP DVP90ST (90° Elbow) 1[...]

61 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 B. V ent Components Diagrams (continued) Figure 16.3 DVP vent components DVP-HPC1 DVP-HPC2 DVP-TRAP1 DVP-TRAP2 DVP-HPCK1-B DVP-HPCK2-B DVP-TRAPK1 DVP-TRAPK2 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length [...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 62 B. V ent Components Diagrams (continued) Figure 16.4 DVP vent components 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK Tra p Ca p Bri[...]

63 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 DVP-TB1 Basement V ent Ca p 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) 3-7/8 in. (98 mm) DVP-TV V ertical T ermination Cap 7-1/4 in. (184 mm) 5-1/4 in. (133 mm) 12-1/2 in. (318 mm) DVP-TVHW V er tical[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 64 B. V ent Components Diagrams (continued) Pipe Length/Inches SL-06D 5-3/4 SL-09D 8-3/4 SL-12D 1 1-3/4 SL-12/17D 1 1-3/4 to 16-3/4 SL-17/24D 16-3/4 to 23-3/4 SL-24D 23-3/4 SL-36D 35-3/4 SL-48D 47-3/4 SL-FLEX-2 24 SL-FLEX-3 36 SL-FLEX-5 60 SL-FLEX-10 120 There must b e[...]

65 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 C. Service Parts Part number list on following page. 7 Log Set Assembly 14 10 10 12 12 (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 1-06 Ending Manufacturing Date: ______ 1 5 2 4 15 6 13 9 9 SL-550TR-D 1 1 11 8 8[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 66 A V AILABLE TO SHIP IN 24 HOURS ITEM COMMON P ARTS SERIAL # P ART NUMBER Burner Ori fi ce NG (#44C) 582-844 Y Burner Ori fi ce LP (#54C) 582-854 Y 1 Mesh Assembly 550-382A Y 2 Burner NG, LP PRE 10-06 POST 10-06 530-206A 530-018 Y Y 3 Glass Door Assembly GLA-550TR [...]

67 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Service Parts Part number list on following page. 7 Log Set Assembly 15 10 10 12 12 (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 1-06 Ending Manufacturing Date: ______ 1 5 2 4 15 6 3 9 9 SL-750TR-D 1 1 11 8 8 13 13 14[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 68 A V AILABLE TO SHIP IN 24 HOURS ITEM COMMON P ARTS SERIAL # P ART NUMBER Burner Ori fi ce NG (#42C) 582-842 Y Burner Ori fi ce LP (#53C) 582-853 Y 1 Mesh Assembly 530-382A Y 2 Burner NG, LP PRE 10-06 POST 10-06 530-216A 530-019 Y Y 3 Glass Door Assembly GLA-750TR [...]

69 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 Service Parts Part number list on following page. (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 1-06 Ending Manufacturing Date: ______ 14 5 2 4 16 6 1 SL-950TR-D 7 Log Set Assembly 10 10 12 12 9 9 1 1 11 8 8 13 13 3 15[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 70 A V AILABLE TO SHIP IN 24 HOURS ITEM COMMON P ARTS SERIAL # P ART NUMBER Burner Ori fi ce NG (#42C) 582-836 Y Burner Ori fi ce LP (#53C) 582-851 Y 1 Mesh Assembly 560-382A Y 2 Burner NG, LP PRE 10-06 POST 10-06 534-21 1A 534-017 Y Y 3 Glass Door Assembly GLA-950TR[...]

71 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 (NG, LP) Exploded Parts Diagram Service Parts SL-550 / 750 / 950TR-D-IPI Beginning Manufacturing Date: 1-06 Ending Manufacturing Date: ______ Intermittent Pilot Ignition V alve Assembly 2 5 4 11 9 7 8 A V AILABLE TO SHIP IN 24 HOURS ITEM COMMON P ARTS SERIAL # P ART[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 72 (NG, LP) Exploded Parts Diagram Service Parts SL-550 / 750 / 950TR-D Beginning Manufacturing Date: 1-06 Ending Manufacturing Date: ______ Standing Pilot Ignition V alve Assembly 1 6 4 5 9 3 8 A V AILABLE TO SHIP IN 24 HOURS ITEM COMMON P ARTS SERIAL # P ART NUMBER 1[...]

73 Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 D. Limited Lifetime W arranty LIMITED LIFETIME W ARRANTY HEA T & GLO GAS APPLIANCE PRODUCTS © 2005 Hearth & Home T echnologies Inc. 060-981D 3/05 BASIC ONE-YEAR W ARRANTY . HEA T & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Ke[...]

Heat & Glo • SL-550 / 750 / 950TR-D • InD • 2044-985 Rev . M • 10/06 74 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com - NOTES - ________________________________________________________________________________ _____________________________________________[...]