HP (Hewlett-Packard) WZ226UT#ABA manuale d’uso

HP EliteBook 2540p Notebook PC Maintenance and Service Guide[...]

© Copyright 2010 Hew lett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel and Core are U.S. registered trademarks of Intel Corporation. Java is a U .S. trademark of Sun Microsystems, Inc. Microsoft, Windows, and Windows Vista are U.S. registered trademarks [...]

MSG Revision history Revision Publication date Description A December 2010 The 6.35-cm (2.50-in) hard drive is installed in the op tical drive bay, using a hard drive carrier, spar e part number 598787-001. The information was updated in the following locations: Illustrated parts catalog on page 19 , Sequential part number listing on page 32 , and [...]

iv MSG Revision history[...]

Safety warning notice WARNING! To reduce the possibility of heat-related inju ries or of overhea ting the compute r, do not place the compu ter directly on your lap or obstru ct the computer air vents. Use the computer only on a hard, flat surface. Do n ot allow another hard surface, such as an adjoining option al printer, or a soft surface, such a[...]

vi Saf ety warning notice[...]

Table of contents 1 Product description ............ ......... ........... ......... ......... .......... .......... ........... ........ ............ ... ............. ........ ......... .. 1 2 External component id enti fication ...... ......... ........ ........... ........ ........ .......... ........ ........... ........ ... ........... ......[...]

Computer feet . .......... .......... .......... ........... ......... ........... .......... .......... .......... ........... .......... ... 43 Batter y ........ .............. .............. ........... ............. .............. .............. .............. .............. ... ........ 44 SIM ....... ............. ............. ..............[...]

Windows XP ................ ......... ........ ........... ........ ......... .......... ......... ........ ........... ........ ......... ......... ........ 112 Start ing Compute r Setup ....... .............. ............. .............. .............. ............. .............. ........ 112 Using C omputer S etup ... .................. .......[...]

Exter nal monit or .. ........... ........... ........... ........... ........... ........... ........... ........... ........... ......... .... ............ . 137 RJ-11 ( modem) ... ............. ............ .............. .............. ............. ............ .............. ............. ..... .............. . 138 RJ-45 (network) ...........[...]

1 Product description Category Description Product Name HP EliteBook 2540p Notebook PC Processors Intel® Dual Core™ pr ocessors (sup port Intel Turbo Boost Technology): ● Intel Dual Core i7-640LM 2.13-GHz pr ocessor, (turbo up to 2.93-GHz), 4-MB L3 cache, 4 threads, low-voltage (25-W) ● Intel Dual Core i7-620M 2.66-GHz pro cessor, (turbo up [...]

Category Description Internal storage Computer models equipped with a standard-voltage (35-W) processor support the followin g 2.5-in storage devices: ● 500-GB hard drive (720 0-rpm, SMART SATA II) ● 320-GB hard drive (720 0-rpm, SMART SATA II) ● 320 self-encrypting drive (SED) GB h ard drive (7200-rpm, SMART SATA II) ● 250-GB hard drive (7[...]

Category Description Supports “no modem” option Modem cable not included Ethernet Intel 82577-LM 10/100/1000 GB ne twork interface card (NIC ) with iAMT 4.0 support S3/S4/S5 wake on LAN: DC - no S3/S4/S5 wake on LAN: AC - yes NIC power-down technology Ethernet cable not included Wireless Integrated wireless local area network (WLAN) options by [...]

Category Description Ports ● 1394a ● 3-pin AC power ● Headphone/microphone combo audio ● DisplayPort ● Docking ● RJ-11 (modem) ● RJ-45 (Ethernet, includes link and activity lights) ● USB 2.0 (4 on computer models equipped with standar d voltage processors, 3 on computer models equipped with low voltage processors; 1 powe red) ● VG[...]

Category Description Preinstalled with Microsoft® O ffice: ● Windows 7 Home Basic 32 ● Windows 7 Home Premium 32/64 ● Windows 7 Professional 32/64 ● Windows Vista Home Basic ● Windows Vista Business 32 with Windows 7 license ● Windows Vista Business 32 with Windows 7 license with Personal without PowerPoint ● Windows Vista Business 3[...]

Category Description Web-only support : ● Windows 7 Enterprise 32/64 ● Windows 7 Ultimate 32/64 ● Windows Vista Business 64 ● Windows Vista Enterprise 32/64 Serviceability End-user replaceable parts: ● AC adapter ● Bluetooth module ● Battery ● Expansion memory module ● Hard drive ● Optical drive ● Power cord ● Primary memory[...]

2 External component identification Components include d with the computer may vary by region and mode l. The illustrations in this chapter identify the standard feat ures on most comput er models. To see a list of hardware insta lled in the computer, follow these steps: In Window s 7: ▲ Select Start > Control Panel > System and Security &g[...]

Display components Item Component Description 1 WWAN antennas (2)* Send and receive wireless signals to communicate with WWANs (selec t models on ly). 2 WLAN antennas (2) * Send and receive wireless sign als to communicate with WLANs (select models only). 3 Webcam light On: The webcam is in use. 4 Webcam Records audio and video and capture s still [...]

Item Component Description 7 Ambient light sensor Automatically ad justs the display brightness based on the lighting conditions in your environme nt. *The antennas are not visible from the outsid e of the comput er. For optimal transmission, keep the areas immedia tely around the antennas free from obstructions. To see wireless regulatory notices,[...]

Buttons and fingerprint reader 10 Chapter 2 External component identification[...]

Item Component Description (1) Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, pr ess the button to shut down the computer. NOTE: Although you can shut down the computer with the power button, the recommended procedure is to use the Windo ws Shut down command (in Windows 7) or Window[...]

Item Component Description (8) Volume up button Increases speaker volume. (9) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon. Keys Item Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system func[...]

Pointing device components Item Component Description (1) Left TouchPad button* Functions like the left button on an external mouse . (2) TouchPad* Moves the pointer and selects or activates items on the screen. (3) Left pointing stick button* Functions like the left button on an external mouse . (4) Pointing stick* Moves the pointer and selects or[...]

Front components Item Component Description (1) Business card slot Holds a business card in position so that the webcam can capture the information o n the card. (2) Wireless light ● Blue: An integrated wireless device, such as a WLAN device, the HP Mobile Broadband Module (select models only), a nd/or a Bluetooth device, is on. ● Amber: All wi[...]

Left-side components NOTE: Refer to the illustration that most closely matches your computer. Computer model equip ped with a low-voltage processo r Item Component Description (1) Power connector Connects an AC adapter. (2) RJ-11 (modem) jack Connects a m odem cable (select models only) . (3) Powered USB port Provides power to a USB device, such as[...]

Rear components Item Component Description (1) RJ-45 network) jack Connects a network cable. (2) USB ports (2) Connect optional USB devices. Right-side components Item Component Description (1) ExpressCard34 slot Supports optional ExpressCards. (2) Docking connector Connects an optional docking device. (3) Security cable slot Attac hes an optional [...]

Bottom components Item Component Description (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery. (3) Vents (7) Enable airflow to cool internal components. NOTE: The computer fan starts up au tomatically to cool internal components and preve nt overheating. It is normal for the internal fan to[...]

Item Component Description (7) Wireless module compartment Contains an HP Mobile Broadband Module (select models only) and a WLAN module (select models only). CAUTION: To prevent an unresp onsive system, replace the wireless module only with a wireless module authorized for use in the computer b y the governmental agency that regul ates wireless de[...]

3 Illustrated parts catalog Serial number location The service tag, affixed to the bottom of the comp uter, provides information that ma y be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to th e front of the computer. (2) Serial number (s/n): T hi[...]

Computer major components 20 Chapter 3 Illustrated parts catalo g[...]

Item Description Spare part number (1) 12.1-in, WXGA AntiGlare LED display ass embly (includes display panel cabl e, WLAN antenna transceivers and cables, and WWAN antenna tr ansceivers and cables. See Display components on pa ge 26 for display assembly component spare part n umber information.): For use only with computer models equ ipped with a w[...]

Item Description Spare part number ● For use in Thailand 598790-281 ● For use in Turkey 598790-141 ● For use in the United Kingdom 598790-031 ● For use in the United States 598790-001 (4) RTC battery 481089-001 (5) Memory shield 598793-001 (6) Memory modules (2, 1333-MHz, D DR3): 4 GB 599092-002 2 GB 598856-002 1 GB 598859-002 (7) Top cover[...]

Item Description Spare part number Equipped with an Intel Core i5-520M 2.40- GH z processor for use only in the People's Republic of China and Russia 614966-001 System boards for use on computer models equipped with low -voltage (25-W) processors: Equipped with an Intel Core i7-640M 2.13-GHz p rocessor for use in all countries and regions exce[...]

Item Description Spare part number (22) WLAN module Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Antigua an d Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brune i, Canada, the Cayman Islands, Chile, Colombia, Cost a Rica, the Dominican Repu blic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India[...]

Item Description Spare part number Broadcom 4312G 802.11b/g WiFi Adapter fo r use in Afghanistan, Albania, Alger ia, Andorra, Angola, Antigua and Barbuda, Arg entina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana[...]

Item Description Spare part number 6.35-cm (2.50-in) hard drive: NOTE: The 6.35-cm (2.50-in) hard drive must be installed in the optical drive bay, using a hard drive carrier. Installation of these devices in the hard drive bay is no t supported. ( This option is not available whe n the optical drive is installed.) ● 500-GB, 7200-rpm hard drive 5[...]

Item Description Spare part number (1) Display b ezel For use only with computer models equipped with a webcam 598770-001 For use only with computer models not equippe d with a webcam 598771-001 (2) Webcam module 598803-001 (3) Ambient light sensor b oard 598761-001 (4) Display Hi nge Kit , includes: 598773-001 (5) Display panel cable (includes web[...]

Mass storage Item Description Spare part number (1) 6.35-cm (2.50 -in) mass storage device NOTE: 6.35-cm (2.50-in) devices must be installed in the opt ical drive bay, using a har d drive carrier, spare part number 598787-001 (includes HDD and OD D connector boards and the USB board) . Installation of 6.35-cm (2.50-in) devices in the hard drive bay[...]

Item Description Spare part number (2) 4.57-cm (1.80 -in) mass storage device NOTE: 4.57-cm (1.80-in) devices must be installed in the har d drive bay. Installation of these devices in the optical drive bay is not suppo rted. 4.57-cm (1.80-in) mass storage devices available for use on computer models equipped with a low-voltage (25- W) processor: ?[...]

Plastics Kit Item Description Spare part number Plastics Kit : 598796-001 (1) Optical drive bezel (2) Wireless module compartment co ver (includes one ca ptive sc rew, secured by a C-clip) (3) ExpressCard slot bezel (4) Memory module compartment cover (includes one captive screw, secured by a C-clip) (5) Display hinge covers (6) Bluetooth module co[...]

Miscellaneous parts Description Spare part number AC adap ter 65-W non-PFC AC adapter 613152-001 65-W PFC AC adapter 613161-001 Cable Ki t (includes Bluetooth module cabl e and modem module ca ble) 598766-001 HP 2540 Series Docking Station 598774-001 Power cord For use in Argentina 490371-D01 For use in Australia and New Z ealand 490371-011 For use[...]

Sequential part number listing Spare part number Description 481089-001 RTC battery 490371-001 Power cord for use in Canada and the United States 490371-011 Power cord for use in Australia and New Zealand 490371-021 Power cord for use in Europe, the Middle East, and Africa 490371-031 Power cord for use in Singapore and the United Kingdom 490371-061[...]

Spare part number Description 582562-001 Broadcom 4312G 802.11b/g WiFi Adapter for use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the C ayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, H onduras, Hong Kong, India, Indonesia, Malaysia, Mex[...]

Spare part number Description 593587-001 9-cell, 93-WH, 2.8-AH, Li-ion battery 598759-001 Base enclosure (i ncludes display release latch, battery rele ase latch, LED board and cab le, and rubber feet) 598761-001 Ambient light sensor board 598762-001 System board equipped with an Intel Core i7-640LM 2.13-GHz, low-voltage ( 25-W) processor for use i[...]

Spare part number Description 598789-001 Fan/heat sink assembly for use only with 35-W processors (includes replacement thermal material and replacement thermal material cleaning kit) 598790-001 Keyboard for use in the United States (i ncludes cable) 598790-031 Keyboard for use in the United Kingdom (inclu des cable) 598790-041 Keyboard for use in [...]

Spare part number Description 598794-001 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models equipped w ith a webcam (includes disp lay panel cable, WLAN antenn a transce ivers a nd cables, and WWAN antenna transceivers and cables. 598795-001 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models n[...]

4 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to comple te the removal and re placement procedures: ● Flat-bla ded screw driver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdr iver Service considerations The following sectio ns include so[...]

Cables and connectors CAUTION: When servicing the computer, be sure that c ables are placed in their proper lo cations during the reassembly p rocess. Improp er cable placem ent can damage th e computer. Cables must be handle d with extreme care to avoid d amage. Apply only the tens ion required to unseat or seat the cables during removal an d inse[...]

Grounding guidelines Electrostatic discharge damage Electronic componen ts are sensit ive to electrost atic discharge (ESD). Circuitry design and st ructure determine the deg ree of sensitiv ity. Networ ks bu ilt into many integrated circuits provide some protection, bu t in many cases, ESD conta ins enough power to alter d evice parameters or melt[...]

Packaging and transporting guidelines Follow these groun ding guidelines when p ackaging and transporti ng equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts an d assemblies wi th conductive or appr oved contai ners or packaging. ● Keep ESD-sensitive parts in their conta [...]

Equipment guidelines Grounding equi pment must include eith er a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist stra ps are flexible straps with a minimu m of one megohm ±10% resi stance in the grou nd cords. To pro vide proper ground, wear a strap snugl y against th[...]

Component replacement procedures This chapter provides removal an d replacement procedures. There are as many as 7 2 screws that must be removed, replaced , or loosened when se rvicing the computer. Make special note of each screw size and location during removal and rep lacement. Service tag The service tag, affixed to the bottom of the comp uter,[...]

Computer feet The computer feet are hot melted to the base enclosure in th e locations illustr ated below. Th ere are two different sized feet: the five square feet (1) ar e installed on the fron t and the back of the base enclosure. The three rectang ular feet (2) are installed in the rear/l eft corner of th e base enclosure and near the vent s. C[...]

Battery Description Spare part num ber 9-cell, 93-WH, 2.8-WH Li battery 593587-001 6-cell, 62-WH, 2.8-WH Li battery 593586-001 6-cell, 55-WH, 2.8-WH Li long life battery 593585-001 3-cell, 31-WH, 2.8-WH Li battery 492548-001 3-cell, 28-WH, 2.8-WH Li long life battery 593584-001 Before disa ssembling the compu ter, follow these steps: 1. Shut down t[...]

SIM NOTE: This section applies on ly to computer models with WWAN capability. NOTE: If there is a SIM inserted in th e SIM slot, it must be remove d before disassembling the computer. Be sure that the SIM is reinserted in the SIM slot after reassembling the computer. Before removing the SIM, follow these steps: 1. Shut down the co mputer. If you ar[...]

Bluetooth module Description Spare part number HP Integrated Module with Bluetooth 2.1 Wireless Technology NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare p art number 598766-00 1. 537921-001 Before removing the Bluetooth modul e, follow these steps:[...]

4. Remove the Bluetoot h module (2) from the Bluetooth module compartment cover. Th e Bluetooth module compartment cover is included in t he Plastics Kit, spare part number 598796-001. 5. Remove the Bluetoot h module. Reverse the abov e procedur e to install the Blueto oth module. Component replacement procedures 47[...]

Expansion memory module Description Spare part num ber 4096-MB memory module (1333-MHz, D DR3) 599092-002 2048-MB memory module (1333-MHz, D DR3) 598856-002 1024-MB memory module (1333-MHz, D DR3) 598859-002 Before removing the memory module, follo w these steps: 1. Shut down the co mputer. If you are unsure whether the co mputer is off or in Hiber[...]

5. Remove the memory module (2) by pul ling the module away from the slot at an a ngle. NOTE: The memory module is de signed with a notch to preven t incorrect insertion into th e memory module slot. Reverse this procedure to insta ll the memory module. Component replacement procedures 49[...]

Low-voltage hard drive or solid-state drive NOTE: The 4.57-cm (1.80-in) ha rd drive and solid-stat e driv e spare pa rt kit includes a hard drive or solid-state drive bracket. Description Spare part n umber 4.57-cm (1.80-in), 320-GB, 5400-rpm h ard drive 614537-001 4.57-cm (1.80-in), 250-GB, 5400-rpm h ard drive 598778-001 4.57-cm (1.80-in), 160-GB[...]

3. Lift the right edge o f the hard drive shield (2) , swing it up and to the left, and then remove the cover (3) by sliding it u p and to the right at an angle. The hard drive shie ld is included in the hard drive spare part kit. 4. Lift the right side of the low-voltag e hard drive (1) to di sconnect it from the system board. 5. Remove the low-vo[...]

6. If it is necessary to replace the rubber isolator, separate the edge s of the isol ator from the end of the low-voltage hard drive, and re move the isolato r. 7. If it is necessary to replace th e low-voltage hard drive co nnector , slide the connecto r off of the hard drive. Reverse this procedure to rea ssemble an d install the low-voltage har[...]

WLAN module Description Spare part num ber Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Antigua and Barbuda, Argentin a, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands, Chile , Colombia, Costa Rica, the Dominican Republic, Ecu ador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesi[...]

Description Spare part num ber Broadcom 4312G 802.11b/g WiFi Adapter for use in Afghanistan , Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Arub a, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbad os, Belarus, Belgium, Belize, Benin, Bermuda , Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, B[...]

2. Lift the right edge of the wire less module compartment cover (2) , swing it up and to the left, and remove the cover. The wireless mo dule compa rtment cov er is includ ed in the P lastics K it, spar e part number 598796-001 . 3. Disconnect th e WLAN antenna ca bles (1) from the terminals on the WLAN module. NOTE: The black WLAN antenna cable i[...]

5. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN module s are designed with a notch (4) to prevent incorrect insertion. NOTE: If the WLAN ante nnas are not conne cted to the te rminals on th e WLAN module, the protective sleeves must be insta lled on the antenna conne ctors, as shown in th e following i[...]

WWAN module Description Spare part number HP un2420 Broadband Module for use in all countries and regio ns 531993-001 HP hs2330 HSPA Mobile Broadband Module for use in all countries and regions 574249-001 HP hs2320 HSPA Mobile Broadband Module for use only in Europe, the Middle East, and Africa NOTE: For use only on selected computer models. 574248[...]

3. Remove the WWAN module (3) by pulling the module away from the slo t at an angle. NOTE: WWAN modules are designed with a no tch (4) to prevent incorrect in sertion. NOTE: If the WWAN antennas are n ot connected to the terminals o n the WWAN module, the protective sleeves must be insta lled on the antenna conne ctors, as shown in th e following i[...]

Optical drive NOTE: The optical drive is an op tional feature a nd is avai lable only on computer models equipped with a low voltage (25-W) processor. Description Spare part n umber DVD±RW and CD-RW SuperMulti Double-Layer D rive 598776-001 DVD-ROM Driv e 598775-001 Before removing the optical drive, follow these ste ps: 1. Shut down the co mputer[...]

4. Remove the optical drive (2) from the computer. 5. If it is necessary to replace the optical drive bra cket, position the optical drive with the rear toward y ou. 6. Remove the two Phillips PM2.0×4.0 screws (1) th at secure the optical drive bracket to the o ptical drive. 7. Remove the optical drive bracket (2) . Reverse this procedure to rea s[...]

Standard-voltage hard d rive or solid-state drive NOTE: Installation of the 6.35-cm (2.50-in) hard drive or solid-state drive in the hard drive bay is not supported. The 6.35-c m (2.50-in) hard drive or solid-sta te drive ca nnot be insta lled when the opt ical drive is installed. Description Spare part nu mber 2.50-in, 500-GB, 7200-rpm hard dr ive[...]

Remove the standa rd-voltage hard drive: 1. Remove the four Philli ps PM3.0×3.0 screws (1) and the two Phillips PM2.0×5.0 screws (2) that secure the hard drive carrier to the computer. 62 Chapter 4 Remova l and replacement proced ures[...]

2. Insert a flat-bladed screwdriver or simila r tool into the optical drive tab access (1) and p ress the tab to the right to rel ease the hard drive carrier (2) from the com puter. 3. Remove the four Phillips PM3.0×3.0 screws that se cure the standa rd-voltage hard drive to the hard driv e carrier. 4. Lift the front edge o f the standard-vo ltage[...]

5. Remove the standard-voltage hard drive (2) by sli ding it up and away from the hard drive carr ier at an angle. Reverse the abov e procedur e to reassemble an d install the standa rd-voltage har d drive. 64 Chapter 4 Remova l and replacement proced ures[...]

Switch cover and keyboard Description Spare pa rt number Switch cover (includes power button board and cable) 598800-001 Keyboard for use in country/ region Spare part number Keyboard for use in count ry/ region Spare part number Belgium 598790-A41 Norway 598790-091 Brazil 598790-201 Portugal 5 98790-131 Bulgaria 598790-261 Ru ssia 598790-251 The C[...]

2. Loosen the four captive screws (2) that secure the keyboard to the computer. 3. Turn the computer right-side up, with the front toward you. 4. Open the displa y as far as possible. 5. Lift the right side of the switch cover (1) to detach it from the computer. 6. Release the switch cove r (2) as far as the power button boa rd and ca pacitive boar[...]

9. Swing the rear ed ge of the keyboard (3) up and fo rward until the keyb oard rests upside down on the palm re st. 10. Release the zero insertion force (ZIF) connector (1) to which the keyboa rd cable is atta ched, and then disconnect the keyb oard cable (2) from the system boa rd. 11. Release the ZIF connecto r (3) to which the pointing stick ca[...]

14. Remove the switch cover (3) . Reverse this procedure to insta ll the switch cover and keyboa rd. 68 Chapter 4 Remova l and replacement proced ures[...]

RTC battery Description Spare part num ber RTC battery 481089-001 Before r emoving th e RTC batte ry, follow these steps : 1. Shut down the co mputer. If you are unsure whether the co mputer is off or in Hibern ation, turn the computer on, and th en shut it down thr ough the operating system. 2. Disconnect all ext ernal devices connected to the com[...]

Primary memory module Description Spare part num ber 4096-MB memory module (1333-MHz, D DR3) 599092-002 2048-MB memory module (1333-MHz, D DR3) 598856-002 1024-MB memory module (1333-MHz, D DR3) 598859-002 Memory shield (includes one captive screw) 598793-001 Before r emoving the p rimary memor y module, fo llow these st eps: 1. Shut down the co mp[...]

3. Spread the retaining ta bs (1) on each side of the memory module slot to rel ease the memory module. (The edge o f the module opposite th e slot rises away from the comp uter.) 4. Remove the memory module (2) by pul ling the module away from the slot at an a ngle. NOTE: The memory module is de signed with a notch to preven t incorrect insertion [...]

Display assembly Description Spare part number 12.1-in, WXGA AntiGlare LED display assembly fo r use only with computer models equipped with a webcam (includes display panel cable, WLAN antenna transce ivers and cables, and WWAN antenna transceivers and cables. 598794-001 12.1-in, WXGA AntiGlare LED display assembly for use only with computer model[...]

5. Open the displa y as far as it will op en. 6. Disconnect th e display panel cab le (1) from the system board and release i t from the clip built into the top cover. 7. Release the wireless an tenna cables from th e clips (2) built into the top cover. 8. Disconnect the microphone cable (1) from the system board. Component replacement procedures 7[...]

9. Release the microph one cable and the wirel ess antenna cables from the clips (2) built into the top cover. CAUTION: The display assembly will be unsupported when the fo llowing screws are removed. To prevent damage to the d isplay assemb ly, su pport it before removi ng the screws. 10. Remove the two Torx T8M2.5×6.0 screws (1) that secure the [...]

11. Lift the display assembly straight up to remove it (3) . Component replacement procedures 75[...]

12. If it is necessary to replace the di splay be zel or any of the display assembly internal components: a. Remove the four rubber screw covers (1) and the four Torx T8M2.5×5.0 screws (2) that secure the display bezel to the display assembly. NOTE: The rubber screw covers on the di splay bezel top edge are thicker than the rubber screw covers on [...]

c. Remove the display bezel (4) . The display bezel is available using spare part nu mbers 598770-001 (for u se only with computer mode ls equipped with a webcam) and 598771-00 1 (for use only with computer models not e quipped with a webca m). 13. If it is necessary to replace the ambient light sensor board: a. Release the ZIF connector to which t[...]

c. Remove the ambient l ight sensor board (3) . The ambient light sensor board is available using spare part number 598761-001. 14. If it is necessary to replace the webcam module, display hing es, display panel cable, o r display enclosure: a. Release the display pan el cable (1) from the clips bu ilt into the display enclosu re. b. Disconnect the[...]

e. Disconnect the display panel cable (3) from the passthrough bo ard. f. Remove the display pane l. g. Remove the two Phillip s PM2.0×4. 0 screws (1) that secure each display hinge to the display panel. h. Remove the display hinge s (2) . The display hin ges are included in the Display Hinge Kit, spare part number 598 773-001. i. Remove the Torx [...]

m. Route the webcam mod ule cable (3) throu gh the slot built into the display enclo sure. Reverse this procedure to rea ssemble an d install the displa y assembly. 80 Chapter 4 Remova l and replacement proced ures[...]

Top cover NOTE: The top cover spare pa rt kit includes the To uchPad board and cab le, TouchPad bu tton board and cable, and TouchPad bracket. Description Spare part num ber For use only on computer models equipped with a fi ngerpr int reader (includes fingerprint reader and cable) 598801-001 For use only on computer models not equipped w ith a fin[...]

4. Remove the following scre ws: (1) Four Torx T8M2.5×5.0 screws (2) Three Torx T8M2 .5×6.0 sc rews (3) One To rx T8M2.0 ×5.0 scr ew. (4) One To rx T8M2.0 ×4.0 scr ew. 5. Turn the computer right-side up, with the front toward you. 6. Release the ZIF conne ctor to which th e card reader b oard cable is atta ched, and then disconnect the card rea[...]

8. Release the ZIF conne ctor to which the fin gerpr int re ader board cable is attached, and then disconnect the fingerprint reader boa rd cable (3) from the system board. 9. Lift the rear edge of the top cover (1) , and then swing it up and forward until it re sts at an angle. 10. Lift the front edge of the top cover (2) until it disengages from [...]

Card reader board Description Spare part number Card reader board (includes cable) 598768-001 Card reader board bracket 598767-001 Before removing the card reader board and bracket, follow these steps: 1. Shut down the co mputer. If you are unsure whether the co mputer is off or in Hibern ation, turn the computer on, and th en shut it down thr ough[...]

3. Remove the two Phillips PM 2.0×2.0 broad head screws (1) and the Phillips PM2.0×5.0 screw (2) that secu re the ca rd reade r board br acket to the top c over. 4. Lift the front edge o f the card reader b oard bracket (3) until it rests at an angle. 5. Remove the card reader board bracket (4) by sliding it up and forwa rd at an angle. 6. Slide [...]

7. Remove the card reader bo ard (2) and cable. Reverse this procedure to insta ll the card re ader board, cable, and bracket. Speaker Description Spare part num ber Speaker 598799-001 Before removing the speaker, follow these ste ps: 1. Shut down the co mputer. If you are unsure whether the co mputer is off or in Hibern ation, turn the computer on[...]

Remove the speaker: 1. Disconnec t the speaker cabl e (1) from the system board. 2. Remove the Phillips PM2.0×4.0 screw (2) and the Phillips PM2.0×6.0 screw (3) that secure the speaker to the b ase enclosure. 3. Remove the speaker (4) from the base enclo sure. Reverse this procedure to insta ll the speaker. Bluetooth module cable NOTE: The Blueto[...]

d. Display assembly (see Display assembly on page 72 ) e. Top cover (see Top cover on page 81 ) Remove the Blueto oth module cable: 1. Release the Blueto oth module cable (1) fro m the opening in the b ase enclosure. 2. Disconnect th e Bluetooth modu le cable (2) from the system board. 3. Remove the Bluetoot h module cable. Reverse this procedure t[...]

System board NOTE: The system board spare p art kit includes the processor, replac ement thermal material, and a replacement therma l material cleani ng kit. Description Spare part num ber System boards equipped with a st and ard-voltage (3 5-W) processor: Equipped with an Intel Core i7-620M 2.66-GHz proc essor for use in all countries and regions [...]

h. Top cover (see Top cover on page 81 ) i. Speaker (see Speaker on page 86 ) When replacing the system board, be sure that the following components are removed from the defective system board and installe d on the replacement system board: ● SIM (see SIM on page 45 ) ● Memory modules (see Expansion memory module on page 48 and Primary memory m[...]

5. Remove the system board (4) from the base enclosure by sliding it up and to the left. Reverse this procedure to insta ll the system board. Component replacement procedures 91[...]

Modem module NOTE: The modem module spare part kit does not includ e a modem module ca ble. The modem module cable is in cluded in the Cabl e Kit, spare pa rt number 598766-00 1. Description Spare part num ber For use in all countries and regions ex cept Australia and New Z ealand 510099-001 For use only in Australia and New Zealand 510099-011 Befo[...]

3. Disconnect th e modem module cable (3) from the modem module. 4. Remove the modem module. Reverse this procedure to in stall the modem module. Fan/heat sink assembly Description Spare part num ber For use only on computer models equipped with a standard-voltage (35-W) proce ssor 598789-001 For use only on computer models equipped wi th a low-vol[...]

c. Switch cover and keyboard (see Switch cover an d keyboard o n page 65 ) d. Display assembly (see Display assembly on page 72 ) e. Top cover (see Top cover on page 81 ) f. System board (see Syste m board on page 89 ) Remove the fan/heat sink assembly: 1. Turn the system board upside do wn, with the front toward you. 2. Disconnect the fan cable (1[...]

Reverse this procedure to in sta ll the fan/heat sin k assembly. Component replacement procedures 95[...]

5 Computer Setup Windows 7 Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setu p menu items listed in this guide may not b e supported b y your computer. NOTE: An external ke yboard or mouse connected to a USB por[...]

Use the tab key and the arro w keys to select File > Ignore change s and exit , and then press enter . – or – ● To save your changes and exit Computer Setup men us, click the Save icon in the lowe r-left corner of the screen, an d then follow the on-screen instruction s. – or – Use the tab key and the arro w keys to select File > Sa[...]

Computer Setup menus The menu tables in this sect ion provide an over view of Comput er Setup options. NOTE: Some of the Computer Se tup menu items list ed in this chapter may not be supported by your computer. File menu Select To do this System Information ● View identification information for the computer and the batteries in the system. ● Vi[...]

Security menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Administrator Tools Setup BIOS Administrator Password Set up a BIOS administrator password User Management ( requires a BIOS administrat or password) Create New BIOS User Account ● Select from a list of BIOS users. ● Sel[...]

System Configuration menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Language Change the Computer Setup language. Boot Options ● Set a Startup Menu delay (in seconds). ● Set the MultiBoot Express Boot Popup delay in seconds. ● Enable/disable Custom Logo (disabled by default)[...]

Select To do this Device Configurations (continued) NOTE: Availability of these options varies by computer model. ● Enable/disable secondary ba ttery fast charge (enabled by default). ● Enable/disable HP Quick Look (enabled by default). ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP Qu[...]

Select To do this Built-In Device Options ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by defaul[...]

Select To do this AMT Options ● Enable/disable Firmw are Verbosity. ● Enable/disable AMT Setup Prompt (Ctrl-P). ● Enable/disable USB Ke y Provisioning Support. ● Enable/disable Unconfi gure AMT on next boot. ● Select Terminal Emulation Mode. ◦ ANSI ◦ VT100 ● Enable/disable Firmware Progress Event Support. ● Enable/disable Initiate[...]

To navigate and select in C omputer Setup, follow these steps: 1. Turn on or restart the compu ter, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of th e screen. ● To select a menu or a menu item, use the tab key and the keyboard arrow keys an d then press enter , or use a pointi ng devic[...]

Restoring factory settings in C omputer Setup NOTE: Restoring defaults will not change the hard drive mode. To return all settings in Computer Setup to the values that were set at the factory, follow these steps: 1. Turn on or restart the compu ter, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bo[...]

Computer Setup menus The menu tables in this sect ion provide an over view of Comput er Setup options. NOTE: Some of the Computer Se tup menu items list ed in this chapter may not be supported by your computer. File menu Select To do this System Information ● View identification information for the computer and the batteries in the system. ● Vi[...]

Security menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Administrator Tools Setup BIOS Administrator Password Set up a BIOS administrator password User Management ( requires a BIOS administrat or password) Create New BIOS User Account ● Select from a list of BIOS users. ● Sel[...]

System Configuration menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Language Change the Computer Setup language. Boot Options ● Set a Startup Menu delay (in seconds). ● Set the MultiBoot Express Boot Popup delay in seconds. ● Enable/disable Custom Logo (disabled by default)[...]

Select To do this Device Configurations (continued) NOTE: Availability of these options varies by computer model. ● Enable/disable secondary ba ttery fast charge (enabled by default). ● Enable/disable HP Quick Look (enabled by default). ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP Qu[...]

Select To do this Built-In Device Options ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by defaul[...]

Select To do this AMT Options ● Enable/disable Firmw are Verbosity. ● Enable/disable AMT Setup Prompt (Ctrl-P). ● Enable/disable USB Ke y Provisioning Support. ● Enable/disable Unconfi gure AMT on next boot. ● Select Terminal Emulation Mode. ◦ ANSI ◦ VT100 ● Enable/disable Firmware Progress Event Support. ● Enable/disable Initiate[...]

Windows XP Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setu p menu items listed in this guide may not b e supported b y your computer. NOTE: An external ke yboard or mouse connected to a USB port can be used wi[...]

– or – Use the tab key and the arrow keys to select File > Save changes and exit , and th en press enter . Your changes go into effect when the computer restarts. Restoring factory settings in C omputer Setup NOTE: Restoring defaults will not change the hard drive mode. To return all settings in Computer Setup to the values that were set at [...]

Computer Setup menus The menu tables in this sect ion provide an over view of Comput er Setup options. NOTE: Some of the Computer Se tup menu items list ed in this chapter may not be supported by your computer. File menu Select To do this System Information ● View identification information for the computer and the batteries in the system. ● Vi[...]

Security menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Administrator Tools Setup BIOS Administrator Password Set up a BIOS administrator password User Management ( requires a BIOS administrat or password) Create New BIOS User Account ● Select from a list of BIOS users. ● Sel[...]

System Configuration menu NOTE: Some of the menu it ems listed in this section may not b e supported by you r computer. Select To do this Language Change the Computer Setup language. Boot Options ● Set a Startup Menu delay (in seconds). ● Set the MultiBoot Express Boot Popup delay in seconds. ● Enable/disable Custom Logo (disabled by default)[...]

Select To do this Device Configurations (continued) NOTE: Availability of these options varies by computer model. ● Enable/disable secondary ba ttery fast charge (enabled by default). ● Enable/disable HP Quick Look (enabled by default). ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP Qu[...]

Select To do this Built-In Device Options ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by defaul[...]

Select To do this AMT Options ● Enable/disable Firmw are Verbosity. ● Enable/disable AMT Setup Prompt (Ctrl-P). ● Enable/disable USB Ke y Provisioning Support. ● Enable/disable Unconfi gure AMT on next boot. ● Select Terminal Emulation Mode. ◦ ANSI ◦ VT100 ● Enable/disable Firmware Progress Event Support. ● Enable/disable Initiate[...]

6 Specifications Computer specifications Metric U.S. Dimensions Depth 21.34 cm 8.40 in Width 28.22 cm 11.11 in Height (front to back) 2.80 cm to 3.40 cm 1.10 in to 1.34 in Weight 1.50 kg 3.31 lbs Input power Operating voltage 19.0 V dc @ 3.5 A – 65 W Operating current 3.5 A Temperature Operating (not writing to optical disc) 0°C to 35°C 32°F t[...]

12.1-in display specifications Metric U.S. Dimensions Width 16.9 cm 6.7 in Depth 26.2 cm 10.3 in Diagonal 30.8 cm 12.1 in Number of colors Up to 16.8 million Contrast ratio 250:1 (typical) Brightness 180 nits (typical) Backlight LED Character display 80 × 25 Total power consumpt ion 4.0 W Viewing angle +/-40° horizontal, +20°/-40° ver tical (ty[...]

DVD±RW and CD-RW SuperMulti Double-Layer Drive specifications Applicable disc Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD, CD- EXTRA, Portfolio, CD-R, CD-RW), CD- R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-R W, DVD+R, DVD +RW, DVD-RA M CD[...]

Applicable disc Read: Write: Cache buffer 2 MB Data transfer rate 24X CD-ROM 3,600 KB/sec 8X DVD 10,800 KB/sec 24X CD-R 3,600 KB/sec 16X CD-RW 3,600 KB/sec DVD-ROM Drive specifications 123[...]

7 Backup and recovery Windows 7 To protect you r information, use Windows Backup and Restor e to back up individu al files and folder s, back up your entire hard drive (sel ect models only), create system repair discs (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the conten[...]

Backing up your information Recovery after a system failure is as complete as your most current ba ckup. You should create system repair discs (select models only) and your initial backup immediately after softwar e setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably [...]

Performing a recovery In case of system failure or inst ability, the computer provides the following tools to recover your files: ● Windows recovery to ols: You can use Windo ws Backup and Resto re to recover info rmation you have previously backed up . You can a lso use Win dows Startup Repair to fix problems tha t might prevent Windows from sta[...]

Using f11 recovery tools CAUTION: Using f11 complete ly erases hard dr ive contents and reformats the hard drive. All files you have created and an y software installed on th e computer are permanently re moved. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not install[...]

Using a Windows 7 operating syst em DVD (purchased separately) If you are unable to boot (start up) your computer and you cannot use the system repair discs you previously c reated (sele ct models on ly), you mu st purchase a Windows 7 operating syste m DVD to reboot the computer and repair the operating system . Be sure th at your mo st recent bac[...]

Backing up your information Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup. As you add new software and data file s, you should continue to back up your system on a regular ba sis to maintain a reason ably current backup. You can back up your i nform[...]

Performing a recovery In case of system failure or inst ability, the computer provides the following tools to recover your files: ● Windows recovery to ols: You can use the Backup and Restore Center to recover informatio n you have previously backed up. You can also us e Windows Startup Rep air to fix problems that might prevent Windows fr om sta[...]

Using f11 recovery tools CAUTION: Using f11 complete ly erases hard dr ive contents and reformats the hard drive. All files you have created and an y software installed on th e computer are permanently re moved. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not install[...]

6. Select Repair your computer . 7. Follow the on-screen instructions. 132 Chapter 7 Backup and re covery[...]

Windows XP To protect your in formation, use the Windows Backu p utility to back up files and fol ders or create recovery points. In case of system failure, you ca n use the backup files to restore your co mputer. Windows provides the following optio ns: ● Backing up individual files and folders ● Backing up all fi les and folders ● Schedulin[...]

NOTE: The backup process may ta ke over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Accessories > Sy stem Tools > Backup . 2. Follow the on-screen instructions. Performing a recovery In case of system failure or inst ability, the computer provides the following tools to recover your fi[...]

8 Connector pin assignments 1394 Pin Signal 1 TPB- 2 TPB+ 3 TPA- 4 TPA+ Audio-in (microphone)/audio-out (headphone) combo Pin Signal 1 Audio signal in (microphone ) / audio out, left channel (headphone) 2 Audio signal in (microphone ) / audio out, right channel (headphone) 3 Ground (microphone) / ground (headphone) 1394 135[...]

DisplayPort Pin Signal 1 ML_lane 0 (positive) 2 Ground 3 Lane 0 (negative ) 4 Lane 1 (positive) 5 Ground 6 Lane 1 (negative ) 7 Lane 2 (positive) 8 Ground 9 Lane 2 (negative ) 10 Lane 3 (positive) 11 Ground 12 Lane 3 (n egative) 13 Connected to ground 14 Connected to ground 15 Auxiliary channel (positive) 16 Ground 17 Auxiliary channel 18 Hot plug [...]

External monitor Pin Signal 1 Red analog 2 Green analog 3 Blue analog 4 Not connected 5 Ground 6 Ground analog 7 Ground analog 8 Ground analog 9+ 5 V D C 10 Ground 11 Monitor detect 12 DDC 2B d ata 13 Horizo ntal sync 14 Vertical sync 15 DDC 2B clock External monitor 137[...]

RJ-11 (modem) Pin Signal 1U n u s e d 2T i p 3R i n g 4U n u s e d 5U n u s e d 6U n u s e d RJ-45 (network) Pin Signal 1 Transmit + 2 Transmit - 3R e c e i v e + 4U n u s e d 5U n u s e d 6R e c e i v e - 7U n u s e d 8U n u s e d 138 Chapter 8 Conn ector pin assignments[...]

Universal Serial Bus Pin Signal 1+ 5 V D C 2D a t a 3 Data + 4 Ground Universal Serial Bus 139[...]

9 Power cord set requirements The wide-range input fe ature of the computer permits i t to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC The 3-conductor powe r cord set included wi th t he comput er meets the requirements for use in the country or region where the e quipment is purchased. Power cord sets for u [...]

Requirements for specific countries and regions Country/region Accredited a gency Applicable note nu mber Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEM A 1 Norway NEMKO 1 The People's Republic of China COC 5 South Korea E K 4 S[...]

10 Recycling Battery When a battery has reached the end of its use ful life, do not d ispose of the battery in general household waste. Follo w the local laws and regulati ons in your area for comput er battery dispo sal. Display WARNING! The backlight contains mercury. Caution must be exercised when removing and handling the ba cklight to avoid d [...]

Perform the following ste ps: 1. Remove all screw covers (1) and screws (2 ) that secure the display bezel to the display assembly. 2. Lift up and out o n the left and ri ght inside edges (1) and th e top and bottom inside edges (2) of the display beze l until the bezel disengag es from the display assembly. 3. Remove the display bezel 3. Display 1[...]

4. Disconnect all disp lay panel cables (1) from the display i nverter and remove the inverte r 2. 5. Remove all screws (1) that secure the display panel a ssembly to the display enclosure. 6. Remove the display panel assembly (2) from the display enclosure. 7. Turn the display pa nel assembly upside down . 8. Remove all screws that secure the disp[...]

10. Remove the display pan el frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlig ht cover (2) and swing it outward. 13. Remove the backlight cover. 14. Turn the display panel righ t-side up. 15. Remove the backlight cables (1) from the clip (2) in th[...]

16. Turn the display pane l upside down. 17. Remove the backlight frame from th e display panel. WARNING ! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damag ing this compon ent a nd causing exposure to th e mercury. 18. Remove the backlight from the backlight frame. 19. Disconnec t the display [...]

22. Release the tape (4) that secures th e LCD panel to the display rea r panel. 23. Remove the LCD panel. 24. Recycle the LCD panel and backlight. Display 147[...]

Index Symbols/Numerics 1394 port connector pinout 135 location 16 A AC adapter, spare part numbers 31, 36 ambient light sensor boa rd location 9 remov al 77 spare part number 27, 34, 77 antenna disconnec ting 55, 57 location 8 audio, product description 2 audio-in jack connector pinout 135 location 16 audio-out jack connector pinout 135 location 16[...]

spare part number 23, 29, 34, 59 specifications 122 DVD±RW and CD-RW SuperMulti Double-Layer Drive precautions 38 remov al 59 spare part number 23, 29, 34, 59 specifications 122 E electrostati c discharge 39 esc key 12 Ethernet, product description 3 ExpressCard slot 16 ExpressCard slot bezel, illustrated 30 external media cards, prod uct descript[...]

precautions 38 product description 2 remov al 59 spare part numbers 23, 29, 34, 59 specifications 122 optical drive bay 18 optical drive bezel, illustrated 30 P packing guidelines 40 plastic parts 37 Plastics Kit contents 30 spare part number 22, 30, 36 pointing devi ce components 13 product description 4 pointing stick 13 pointing stick button 13 [...]

webcam light 8 webcam module removal 78, 79 spare part number 27, 36, 78, 79 Windows applications key 12 Windows logo key 12 wireless antenna disconnec ting 55, 57 location 8 wireless button 11 wireless light 14 wireless module compar tment 18 wireless module compar tment cover illustrated 30 remov al 55 wireless, product description 3 WLAN antenna[...]