Hunter Fan 53069 manuale d’uso

www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 14 PA G E 10 PA G E 5 PA G E 17 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Maintenanc e & Cleaning Blades T roubleshooting Downrod Swit ch Housing Light Kit Prepar ation T able of C ontents ? [...]

www .HunterF an.com 1.888.830.1326 M0002-01 • 11/06/12 • © Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to nearest wall or obstruction 7 feet [...]

T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . www .HunterF an.com 1.888.830.1326 3 M0002-01 • 11/06/12 • © Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 4 M0002-01 • 11/06/12 • © Hunter F an Compan y 4 M0002-01 • 11/06/12 • © Hunter F an Compan y If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches[...]

1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the [...]

www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the screws . They will be needed for blade iron installation. Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while y[...]

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: Ste[...]

KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 8” 3/8” Tighten the setscrew with pliers. DO [...]

1.888.830.1326 9 M0002-01 • 11/06/12 • © Hunter F an Compan y www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan.[...]

www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh[...]

www .HunterF an.com 1.888.830.1326 11 M0002-01 • 11/06/12 • © Hunter F an Compan y Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan st[...]

www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. M0002-01 • 11/06/12 • © Hunter F an Company 12 Insert grommets found in the hardware bag i[...]

www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw[...]

www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing . T wist the lower [...]

www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install a bulb into each of the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of th[...]

www .HunterF an.com 1.888.830.1326 M0002-01 • 11/06/12 • © Hunter F an Compan y 16 Maintenanc e & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off . T o switch the direc tion of air ow , mov e the reverse switch to the opposite position. ON T urn P[...]

www .HunterF an.com 1.888.830.1326 M0002-01 • 11/06/12 • © Hunter F an Compan y 17 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc[...]