Warning: mysql_fetch_array() expects parameter 1 to be resource, boolean given in /home/newdedyk/domains/bkmanuals.com/public_html/includes/pages/manual_inc.php on line 26
IBM 8173 manuale d’uso - BKManuals

IBM 8173 manuale d’uso

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Vai alla pagina of

Un buon manuale d’uso

Le regole impongono al rivenditore l'obbligo di fornire all'acquirente, insieme alle merci, il manuale d’uso IBM 8173. La mancanza del manuale d’uso o le informazioni errate fornite al consumatore sono la base di una denuncia in caso di inosservanza del dispositivo con il contratto. Secondo la legge, l’inclusione del manuale d’uso in una forma diversa da quella cartacea è permessa, che viene spesso utilizzato recentemente, includendo una forma grafica o elettronica IBM 8173 o video didattici per gli utenti. La condizione è il suo carattere leggibile e comprensibile.

Che cosa è il manuale d’uso?

La parola deriva dal latino "instructio", cioè organizzare. Così, il manuale d’uso IBM 8173 descrive le fasi del procedimento. Lo scopo del manuale d’uso è istruire, facilitare lo avviamento, l'uso di attrezzature o l’esecuzione di determinate azioni. Il manuale è una raccolta di informazioni sull'oggetto/servizio, un suggerimento.

Purtroppo, pochi utenti prendono il tempo di leggere il manuale d’uso, e un buono manuale non solo permette di conoscere una serie di funzionalità aggiuntive del dispositivo acquistato, ma anche evitare la maggioranza dei guasti.

Quindi cosa dovrebbe contenere il manuale perfetto?

Innanzitutto, il manuale d’uso IBM 8173 dovrebbe contenere:
- informazioni sui dati tecnici del dispositivo IBM 8173
- nome del fabbricante e anno di fabbricazione IBM 8173
- istruzioni per l'uso, la regolazione e la manutenzione delle attrezzature IBM 8173
- segnaletica di sicurezza e certificati che confermano la conformità con le norme pertinenti

Perché non leggiamo i manuali d’uso?

Generalmente questo è dovuto alla mancanza di tempo e certezza per quanto riguarda la funzionalità specifica delle attrezzature acquistate. Purtroppo, la connessione e l’avvio IBM 8173 non sono sufficienti. Questo manuale contiene una serie di linee guida per funzionalità specifiche, la sicurezza, metodi di manutenzione (anche i mezzi che dovrebbero essere usati), eventuali difetti IBM 8173 e modi per risolvere i problemi più comuni durante l'uso. Infine, il manuale contiene le coordinate del servizio IBM in assenza dell'efficacia delle soluzioni proposte. Attualmente, i manuali d’uso sotto forma di animazioni interessanti e video didattici che sono migliori che la brochure suscitano un interesse considerevole. Questo tipo di manuale permette all'utente di visualizzare tutto il video didattico senza saltare le specifiche e complicate descrizioni tecniche IBM 8173, come nel caso della versione cartacea.

Perché leggere il manuale d’uso?

Prima di tutto, contiene la risposta sulla struttura, le possibilità del dispositivo IBM 8173, l'uso di vari accessori ed una serie di informazioni per sfruttare totalmente tutte le caratteristiche e servizi.

Dopo l'acquisto di successo di attrezzature/dispositivo, prendere un momento per familiarizzare con tutte le parti del manuale d'uso IBM 8173. Attualmente, sono preparati con cura e tradotti per essere comprensibili non solo per gli utenti, ma per svolgere la loro funzione di base di informazioni e di aiuto.

Sommario del manuale d’uso

  • Pagina 1

    ThinkC e n tr e ™ Hard w are Remo v a l an d Rep l ac e m ent Gu i d e Ty p e s 84 2 4 , 84 2 5 , 84 2 8 Ty p e s 81 7 1 , 81 7 2 , 81 7 3 [...]

  • Pagina 2

    [...]

  • Pagina 3

    ThinkC e n tr e ™ Hard w are Remo v a l an d Rep l ac e m ent Gu i d e Ty p e s 84 2 4 , 84 2 5 , 84 2 8 Ty p e s 81 7 1 , 81 7 2 , 81 7 3 [...]

  • Pagina 4

    Second Edition (June 2004) © Copyright International Business Machines Corporation 2004. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.[...]

  • Pagina 5

    Contents Overview . . . . . . . . . . . . . .v Safety information . . . . . . . . . . . .v Additional information resour ces . . . . . . .v T ools requir ed . . . . . . . . . . . . . .v Handling static-sensitive devices . . . . . . .v Replacing customer replaceable units (CRUs) . . . . . . . . . . . . . . .1 Opening the cover . . . . . . . . . . . [...]

  • Pagina 6

    iv Hardwar e Removal and Replacement Guide[...]

  • Pagina 7

    Overview This guide contains instructions for replacing the following customer replacement units (CRUs): v Power supply v System board v Micropr ocessor v Hard disk drive v Memory modules Safety information Do not open your computer or attempt any repair before reading the “Important safety information” in the Quick Reference that was included [...]

  • Pagina 8

    v Before you replace a new CRU, touch the static-protective package containing the CRU to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body . v When possible, remove the new CRU from the static-protective packaging, and install it dire[...]

  • Pagina 9

    Replacing customer replaceable units (CRUs) Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . Openi[...]

  • Pagina 10

    Locating components The following illustration will help you locate the various components in your computer . 1 Diskette drive lock 5 Power supply assembly 2 Memory modules 6 CD or DVD drive (hard disk drive is under the CD drive) 3 Battery 7 CD or DVD drive lock 4 PCI riser 2 Hardwar e Removal and Replacem[...]

  • Pagina 11

    Identifying parts on the system board The system board (sometimes called the planar or motherboard ) is the main circuit board in your computer . It provides basic computer functions and supports a variety of devices. The following illustration shows the locations of parts on the system board. 1 Fan connectors (2) 8 Diskette drive conne[...]

  • Pagina 12

    2. Pivot the drive bay assembly upward to gain access to the cable connections. 3. Locate the power supply . See “Locating components” on page 2. Note: Note the routing of the power supply cables. It is important to route the cables the same way when installing a new power supply assembly . 4. Disconnect the power cables from the hard disk driv[...]

  • Pagina 13

    7. Remove the screws at the rear of the chassis that secure the power supply . 8. Slide the power supply forward and remove from the computer . Replacing customer replaceable units (CRUs) 5[...]

  • Pagina 14

    9. Install the new power supply into the chassis so that the screw holes in the power supply align with those in the chassis. Note: Use only the screws provided by IBM. 10. Install and tighten the four screws at the rear of the chassis that secure the power supply . 11 . Reconnect the speaker wire to the system board. 12. Reconnect power supply con[...]

  • Pagina 15

    Removing and replacing the system board assembly Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . [...]

  • Pagina 16

    installed. 5. Carefully note the location of all cable connections on the system board. It will be necessary to reconnect them properly after installing the new system board assembly . Note: Note the cable routing. It is important to route the cables the same way when installing a new system board. 6. Disconnect the diskette drive cable from the sy[...]

  • Pagina 17

    10. Using the two blue handles provided, lift the system board assembly out of the computer . 11 . Place the old system board next to the new system board on a clean, flat surface. 12. Remove the micropr ocessor from the old system board. Go to “Removing and replacing the micropr ocessor” on page 10. Return here after removing the micropr ocess[...]

  • Pagina 18

    Removing and replacing the microprocessor Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . Importa[...]

  • Pagina 19

    4. Release the lever 1 holding the micropr ocessor heat sink. 5. Remove the heat sink, and do one of the following: v If you are replacing the micropr ocessor , place the old heat sink aside. Yo u must use the new heat sink shipped with the new micropr ocessor . Note Do not use the old heat sink with the a new micropr ocessor . If you use the[...]

  • Pagina 20

    Notes: a. Notice of the orientation of the notches 1 on the micropr ocessor . This is important when reinstalling the micropr ocessor on the system board. * XXXXXXXXX* b. Do not drop anything on the socket while it is open. Keep all contacts as clean as possible. 7. To install the micropr ocessor , do one of the following: Attention To avoid [...]

  • Pagina 21

    b. Remove the new micropr ocessor from its static-protective package. * XXXXXXXXX* c. Hold the micropr ocessor 2 by its sides and loosen the black cover 3 on the micropr ocessor , but do not remove the black cover . d. Place the micropr ocessor on the static-protective package. e. Use the vacuum pen 1 to pick up the new micropr oc[...]

  • Pagina 22

    b. Install the micropr ocessor by inserting it straight down into the socket of the new system board. 8. Pivot the retaining plate 1 closed, and lock the lever 3 to secure the micropr ocessor 2 in place. Be sure to engage the retainer tab when locking the micropr ocessor . *XXXXXXXXX* 9. Do one of the following: v If you have repl[...]

  • Pagina 23

    Removing and replacing memory modules Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . To remove a[...]

  • Pagina 24

    installed. 4. Locate the memory connectors. See “Locating components” on page 2. 5. Open the retaining clips, and lift the memory module out of its connector . 6. Insert the replacement memory module in the memory connector . Ensure the notch on the replacement memory module 1 aligns correctly with the connector key 2 on the system [...]

  • Pagina 25

    7. Reinstall the PCI riser and adapters if they were removed. 8. Pivot the drive bay assembly back to the original position. 9. Close the cover and reconnect the external cables . Go to “Completing the installation” on page 19. Replacing customer replaceable units (CRUs) 17[...]

  • Pagina 26

    Removing and replacing a hard disk drive Attention Do not open your computer or attempt any repair before reading the “Safety notices” in the Quick Reference that was included with your computer . If you no longer have this copy of the Quick Reference , you can obtain one online from the IBM We b site at http://www.ibm.com/pc/support . 1. Open [...]

  • Pagina 27

    6. Remove the old hard disk drive from the blue bracket by flexing the bracket. Do not touch the circuits 5 on the hard disk drive. 7. Insert the new hard disk drive into the blue bracket aligning the pins 1 through 4 on the bracket with the holes in the hard disk drive. 8. Insert the hard disk drive into hard disk bay with the ci[...]

  • Pagina 28

    Attention Keep cables 1 through 3 clear of the hinges and sides of the computer chassis. 3. Make sure that the drive locks on the drive bay assembly are both in the locked position . Otherwise, you cannot close the cover . 4. Close the cover . 5. If a cover lock is installed, lock the cover . 6. If your computer is being placed in the v[...]

  • Pagina 29

    7. Reconnect the external cables. Plug the power cord into the computer then into a properly grounded power receptacle. 1 Power cord connector 9 Parallel connector 2 Cable lock latch 10 Audio line-in connector 3 Rope clip (U-bolt) holes 11 Audio line-out connector 4 PCI and PCI express adapter slots 12?[...]

  • Pagina 30

    3. When you are prompted to select a language, press the number on your keyboard which corresponds to the language then press Enter . 4. When prompted to change the serial number , press Y. 5. T ype in the seven character serial number of your computer then press Enter . 6. When prompted to change the machine type/model, press Y. 7. T ype in the se[...]

  • Pagina 31

    [...]

  • Pagina 32

     Part Number: 19R0821 Printed in USA (1P) P/N: 19R0821[...]