Warning: mysql_fetch_array() expects parameter 1 to be resource, boolean given in /home/newdedyk/domains/bkmanuals.com/public_html/includes/pages/manual_inc.php on line 26
Jet Tools JWSS-10CS manuale d’uso - BKManuals

Jet Tools JWSS-10CS manuale d’uso

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Vai alla pagina of

Un buon manuale d’uso

Le regole impongono al rivenditore l'obbligo di fornire all'acquirente, insieme alle merci, il manuale d’uso Jet Tools JWSS-10CS. La mancanza del manuale d’uso o le informazioni errate fornite al consumatore sono la base di una denuncia in caso di inosservanza del dispositivo con il contratto. Secondo la legge, l’inclusione del manuale d’uso in una forma diversa da quella cartacea è permessa, che viene spesso utilizzato recentemente, includendo una forma grafica o elettronica Jet Tools JWSS-10CS o video didattici per gli utenti. La condizione è il suo carattere leggibile e comprensibile.

Che cosa è il manuale d’uso?

La parola deriva dal latino "instructio", cioè organizzare. Così, il manuale d’uso Jet Tools JWSS-10CS descrive le fasi del procedimento. Lo scopo del manuale d’uso è istruire, facilitare lo avviamento, l'uso di attrezzature o l’esecuzione di determinate azioni. Il manuale è una raccolta di informazioni sull'oggetto/servizio, un suggerimento.

Purtroppo, pochi utenti prendono il tempo di leggere il manuale d’uso, e un buono manuale non solo permette di conoscere una serie di funzionalità aggiuntive del dispositivo acquistato, ma anche evitare la maggioranza dei guasti.

Quindi cosa dovrebbe contenere il manuale perfetto?

Innanzitutto, il manuale d’uso Jet Tools JWSS-10CS dovrebbe contenere:
- informazioni sui dati tecnici del dispositivo Jet Tools JWSS-10CS
- nome del fabbricante e anno di fabbricazione Jet Tools JWSS-10CS
- istruzioni per l'uso, la regolazione e la manutenzione delle attrezzature Jet Tools JWSS-10CS
- segnaletica di sicurezza e certificati che confermano la conformità con le norme pertinenti

Perché non leggiamo i manuali d’uso?

Generalmente questo è dovuto alla mancanza di tempo e certezza per quanto riguarda la funzionalità specifica delle attrezzature acquistate. Purtroppo, la connessione e l’avvio Jet Tools JWSS-10CS non sono sufficienti. Questo manuale contiene una serie di linee guida per funzionalità specifiche, la sicurezza, metodi di manutenzione (anche i mezzi che dovrebbero essere usati), eventuali difetti Jet Tools JWSS-10CS e modi per risolvere i problemi più comuni durante l'uso. Infine, il manuale contiene le coordinate del servizio Jet Tools in assenza dell'efficacia delle soluzioni proposte. Attualmente, i manuali d’uso sotto forma di animazioni interessanti e video didattici che sono migliori che la brochure suscitano un interesse considerevole. Questo tipo di manuale permette all'utente di visualizzare tutto il video didattico senza saltare le specifiche e complicate descrizioni tecniche Jet Tools JWSS-10CS, come nel caso della versione cartacea.

Perché leggere il manuale d’uso?

Prima di tutto, contiene la risposta sulla struttura, le possibilità del dispositivo Jet Tools JWSS-10CS, l'uso di vari accessori ed una serie di informazioni per sfruttare totalmente tutte le caratteristiche e servizi.

Dopo l'acquisto di successo di attrezzature/dispositivo, prendere un momento per familiarizzare con tutte le parti del manuale d'uso Jet Tools JWSS-10CS. Attualmente, sono preparati con cura e tradotti per essere comprensibili non solo per gli utenti, ma per svolgere la loro funzione di base di informazioni e di aiuto.

Sommario del manuale d’uso

  • Pagina 1

    Operating Instructions and Parts Manual SuperSaw Model: JWSS-10CS WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-708781 Ph.: 800-274-6848 Revision B 07/06 www.wmhtoolgroup.com Copyright © WMH Tool Group This manual is bookmarked[...]

  • Pagina 2

    2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the Unit ed States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can aut horize warranty repair, assist you in obtaini[...]

  • Pagina 3

    3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents .............................................................................................................. ............................ 3 Ordering Repl[...]

  • Pagina 4

    4 Troubleshooting ................................................................................................................ .......................... 28 Parts .......................................................................................................................... .................................. 29 XACTA Fence II Homesho[...]

  • Pagina 5

    5 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. This Table Saw is designed [...]

  • Pagina 6

    6 xxxxxxxxxxxxx xxxxxxxxxxxxxxx xxxxxxxxxxxxxxx xxxxxxxxxxxxxxx xxx 21. Provide for adequate space surroundi ng work area and non-glare, overhead light ing. 22. Keep the floor around the machi ne clean and free of scrap materia l, oil and grease. 23. Keep visitors a safe distance from the work area. Keep children away. 24. Make your workshop child [...]

  • Pagina 7

    7 The most common accidents among ta ble saw users, accor ding to statistics, ca n be linked to kickback, the high-speed expulsion of materia l from the table that can strike the operator. Kickback can also result in operator’s hands being pulled into the blade. Kickback Prevention Tips to avoid the most common causes of kickback: • Make sure t[...]

  • Pagina 8

    8 Read and understand the entire contents of this manual before attempting assembly or operation ! Failure to comply may cause serious injury Contents of the Shipping Containers 1 Table saw 1 Right Wing Extension 1 Splitter Guard Assembly 1 Accessory Package 1 Owner’s Manual 1 Warranty Card Accessory Package Box 1 Splitter Guard Assembly (A) 2 Mi[...]

  • Pagina 9

    9 Left Wing Extension Box (optional accessory) 1 Left Wing Extension w/Miter Slot 1 Miter Gauge 1 Miter Gauge Bar 1 Miter Gauge Handle 1 Miter Gauge Fence Hardware Bag 4 Socket Head Cap Screws M10x90 4 Lock Washers M10 4 Flat Washers M10 1 Hex Wrench 8mm XACTA Fence II Homeshop 30/52 Box One: 1 XACTA Fence II 1 Lock Lever Knob Box Two: 1 Front Rail[...]

  • Pagina 10

    10 Assembly Unpacking and Clean-Up Do not connect th e table saw to the power source until assembly has been completed! Failure to comply may cause serious injury! • Tool: 12mm Wrench 1. Remove all content s from the shipping container. Do not discard any shipping material until the saw is set up and running satisfactorily. 2. Carefully move saw [...]

  • Pagina 11

    11 Mounting Rails Hardware: Front Rail, Rear Rail, (4) M8x16 Socket Head Cap S crews, (4) M8 Flat Washers, (4) Lock Washers, (2) 1/4-20 x 1-1/2 Hex Cap Screws, (4) 1/4” Flat Washers, (2) 1/4” Lock Washers, (2) 1/4” hex nuts. Tools: 6 mm hex wrench, two 13mm wrenches Refer to Figures 4 and 5. 1. Mount the front rail (A) to the underside of the[...]

  • Pagina 12

    12 Miter Gauge for Left Extension Wing Hardware: Miter Gauge Tools: Cross Point Screw Driver, Square 1. Change the angle on the miter gauge by loosening handle (E, Fig. 7) and turning the fence (F, Fig. 7) to desi red angle. To move gauge beyond index stops of 45 ° and 90 ° , flip back the stop (G, Fig. 7). 2. Adjust index stops by turning one of[...]

  • Pagina 13

    13 The support plate underneath the sli ding table (Figure 10) has an inn er tab (A) and an outer tab (B). When placing the table onto the leveling bracket (D, Fig. 8), the leveling bracket must be positioned between the inne r and outer tabs and the slots in the tabs (C, Fig. 10) must straddle the screws (A, Fig. 8) that secure the leveling bra ck[...]

  • Pagina 14

    14 Sliding Table Miter Gauge Hardware: Miter Gauge, Fen ce, (2) Handles, Stop, Fence Bar, Indicator Bar, Bushing, Bracket Clamp Assembly & (2) Handles Tools: 2.5mm Hex Wrench 1. Slide the miter gauge fence (B, Fig. 13) into the bar (A, Fig. 13) and attach to the miter gauge body (C, Fig. 13 ) with two handles (D, Fig. 13). Note: the 45° mitere[...]

  • Pagina 15

    15 Mounting the Switch Assembly Hardware: (2) 1/4x1/2 Hex Cap Screws, (2) 1/4 Lock Washe rs, (2) 1/4 Flat Washers. Tool: 4mm Hex Wrench Referring to Figure 15: Mount the switch assembly (A) to the bottom side of the front rail (B) with two butto n head cap screws (C) a nd two washers (D ). Note: The switch assembly can be installed in various locat[...]

  • Pagina 16

    16 table, until it is level with the saw table (Figure 17). As one part of the edge become s level with the table, tighten the clamp on that side. Then move to the other side an d repeat, until the full length of the edge is level with the saw table. Lay a straight edge acro ss both extension table and saw table to ensure proper leveling. When the [...]

  • Pagina 17

    17 slot (A. Fig. 21), orient the guide tube (B) with respect to the rail (C) as shown in Figure 21. If your left table wing is the sliding table type (D, Fig. 22), mount the gui de tube (F) so it lines up with the left edge on the angle iron portion of the rail (E). Referring to Figure 23: 1. Align the holes in the bottom of the guide tube (G) with[...]

  • Pagina 18

    18 4. Raise or lower two nylon adjustment scre ws (A, Fig. 27) the same number of turns until the space between the bottom of the fence and the table is the same. Care m ust be taken to raise or lower the fence on each side equall y or the fence may not be 90 ° to the table after the height adjustment is performed. Parallel to the Miter Slot Adjus[...]

  • Pagina 19

    19 Installing the Blade When installing or changing saw blade, always disconnect sa w from power source! Failure to com ply may cause serious injury! Hardware: Blade Tools: Arbor Wrench, Scrap Piece of Wood 1. Raise the blade arbor and make sure th e arbor is at the zero degree position. 2. Remove the arbor nut (A, Fig. 30) an d flange (B, Fig. 30)[...]

  • Pagina 20

    20 Blade Guard Assembly Hardware: Blade Guard Assembly, Splitter Guard Assembly Tools: 12mm Wrench, 17mm Wrench or Adjustable Wrench, 3mm Hex Wrench 1. With a 3mm hex wren ch, loosen two set screws (G, Fig. 34) on the splitter guard assembly and remove the bracket. 2. Remove the hex nut and lock washer from the threaded end of blade guard sh aft an[...]

  • Pagina 21

    21 Hooks for Miter Gauge and Fence Hardware: (2) Miter Gauge Ho oks, (2) Fence Hooks, (4) M8x16 Ca rriage Bolts, (4) M8 Fl at Washers, (4) M8 Loc k Washers & (4) He x Nuts Tool: 13mm Wrench 1. Mount the two fence hooks (A, Fig. 38) with two M8x16 carriage bolt s, two M8 flat washers, two M8 lock washers and two M8 hex nuts. Helpful Hint: Removi[...]

  • Pagina 22

    22 Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or br eakdown, grounding provides a path of least resistance fo r electric current to re duce the risk of ele ctric shock. This tool is equipped with an electric cord having an equipmen t-grounding conductor a[...]

  • Pagina 23

    23 Adjustments Blade Alignment Tools: 8mm Hex Wrench, Combinatio n Square & Marker Blade alignment with the miter sl ot is adjusted at the factory. After a period of use, or after moving the saw to another location, the blade may no longer be aligned properly. To check and align the blade, see Figure 41. 1. Disconnect saw from t he power source[...]

  • Pagina 24

    24 Adjusting 45 ° and 90 ° Positive Stops The stops have been adju sted at the factory. After a period of use, or, after moving the saw to another location, the stops may n o longer be set properly. To check and adjust the stops: Tool: 12mm Wrench, Combination Square 1. Disconnect saw from power source, un plug. 2. Raise the saw blade to its maxi[...]

  • Pagina 25

    25 Wear Adjustment in Raising Mechanism As the worm gear wears with time you may notice a little play in the handwhe el. To adjust for wear in the raising mechani sm: 1. Disconnect the machine from the power source, unplug. 2. Referring to Figure 48, remove the front panel (D) by unscrewing the lock knob (A), pull ing off the handwheel (B) and remo[...]

  • Pagina 26

    26 Changing Poly V-Belt Make all machine adjustments or m aintenance with the machine unplugged from the power source. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source, unplug. 2. Lower the blade to its lowest point and tilt to 45°. This will allow ea sy access to the poly v- belt. 3. Take the tension off[...]

  • Pagina 27

    27 Maintenance General Maintenance Cabinet and Motor : Keep the inside of the cabinet clear of sa wdust and wood chips. Vacuum out the inside of the cabinet an d blow out the inside with an air hose. Make sure the motor fan and fan cover are also kept clear of sawdust. Worm Shafts and Trunnions: Use a wire brus h and a cleaner/degreaser to clean wo[...]

  • Pagina 28

    28 Troubleshooting Trouble Possible Cause Solution Saw stops or will not start 1. Overload tripped 2. Saw unplugged from wall or moto r 3. Fuse blown or circuit b reaker tripped 4. Cord damaged 5. Starting Capacitor is bad 6. Centrifugal S witch bad or out of adjustment 1. Allow motor to cool a nd push reset button found on “On/Off” Assembly 2.[...]

  • Pagina 29

    29 Parts XACTA Fence II Homeshop 30/52 Fence Assembl y Index No. Part No. Description Size Qty 1 ............... HF2-101 ................... Left Side Plate ...................................................... ................ .................... 1 2 ............... HF2-102 ................... Fence Body Assembly ................................[...]

  • Pagina 30

    30 Cabinet Assembly Index No. Part No. Description Size Qty 1 ............... JWSS10CS-01 ......... Cabinet ................................................................. ................... ................. 1 2 ............... JW SS10CS-02 ......... Door ..................................................................... .................. .[...]

  • Pagina 31

    31 Guard Assembly Index No. Part No. Description Size Qty 1 ............... 200321 ..................... Support Arm ......................................................... ................ .................... 1 2 ............... TS-2342061 ............. Nylon Lock Nut ..................................................... M6 ................... [...]

  • Pagina 32

    32 Table Assembly Index No. Part No. Description Size Qty 1 ............... TS-1550061 ............. Flat Was her .......................................................... M8 ................. ............ 13 2 ............... TS-1551061 ............. Lock Washer ........................................................ M8 ................... .....[...]

  • Pagina 33

    33 Table Assembly Index No. Part No. Description Size Qty 58f ............ 200353 ..................... Switch Bracket ..................................................... .................. .................. 1 58g ........... 200354 ..................... Switch Box ........................................................... ................. ...[...]

  • Pagina 34

    34 Table Assembly[...]

  • Pagina 35

    35 Sliding Table Assembly Index No. Part No. Description Size Qty 1 ............... 200364 ..................... Sliding Table ........................................................ ............... ..................... 1 2 ............... 200411 ..................... Wiper Bracket w/Wiper ........................................ ................[...]

  • Pagina 36

    36 Sliding Table Assembly Index No. Part No. Description Size Qty 57 ............. 200374 ..................... 90° Adjust able Plate ............................................. 0.02” ............... ............. 2 58 ............. NH061000 ................ Nut ........................................................................ M6 ......[...]

  • Pagina 37

    37 Sliding Table Assembly[...]

  • Pagina 38

    38 Rail Assembly Index No. Part No. Description Size Qty ................. 708783Z ................... Rail Assembly - Standard (30”) ........................... .......................... .......... 1 ................. 708782Z ................... Rail Assembly - Long Table (52”) ........................ ............................ ........ 1 [...]

  • Pagina 39

    39 Rail Assembly[...]

  • Pagina 40

    40 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 1 ............... 200310 ..................... Rear Tru nnion Bracket ......................................... ...................... .............. 1 2 ............... TS-1550061 ............. Flat Was her .......................................................... M8 .....[...]

  • Pagina 41

    41 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 51 ............. 200404 ..................... Handle .................................................................. .................................... 2 52 ............. 150045 ..................... K nob ................................................................[...]

  • Pagina 42

    42 Motor & Trunnion Assembly[...]

  • Pagina 43

    43 Wiring Diagrams 115V Wiring[...]

  • Pagina 44

    44 230V Wiring WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.co m[...]