Kathrein UFS 922 manuale d’uso

Operating manual English UFS 922 si/sw T win HDTV satellite receiver with hard disk[...]

2 Dear customer , this Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new receiver . We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. T o help you understand particular specialist terms that cannot be transl[...]

3 Contents Preface............................................................................................................................................................................. 2 Contents ...................................................................................................................................................[...]

4 DANGER! W ARNING! CAUTION! GB Safety Instructions – Important Information This page contains important information about the operation, installation location and connection of the unit. Read these instructions carefully before starting to use the unit. Mains cable Make sure that the mains cable (power supply cable) is not damaged. Units with a [...]

5 Make sure that the fan at the rear of the unit and the ventilation slots on the unit are not blocked or covered in any way . Otherwise the unit may overheat. Adjust the fan speed to the temperature conditions in the receiver . There is a risk of re! Important Information Channel assignment The channels available on the satellites and transpond[...]

6 Information on Audio MPEG Inc. and S.I.SV .EL, S.P .A: This unit makes use of legally protected technologies, which are protected by patents in the USA and also by other intellectual property rights in other countries. KA THREIN-Werke KG has obtained licences from Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo dell‘elettronica, S.I.SV [...]

7  UFS 922si or UFS 922sw  Remote control RC 670  HDMI cable  Scart cable  Coaxial loop-through cable for loop-through operation  2 batteries AAA 1.5 V  Power supply cable  Operating Manual  Safety instructions (multi-lingual) Receiver features/scope of supply/features Receiver features Scope of supply The UFS 922 HDTV tw[...]

8 Receiver features/scope of supply/features Features  Reception of digital satellite TV channels and radio programmes using DVB-S and DVB-S2 transmission standards  Video decoding of MPEG 2 and MPEG 4/H.264 signals  T wo independent HDTV satellite tuners with loop- through output  Integral 500 GB hard disk for up to 300 hours standard [...]

9 Connection and setup View of rear panel ~ 1 10 2 3 4 5 6 7 8 9 1 1 12 16 13 14 15 17 1. On/Off switch (disconnection from the mains) 2. Mains power cable 3. Fan 4. Optical data stream output (SPDIF/Sony Philips Digital Interface Format) for Dolby Digital AC 3 audio 5. Data interface (for service only) 6. Audio outputs (L/R) - cinch sockets 7. Vid[...]

10 Connect the Sat-IF inputs on the receiver to the satellite reception system. Use coaxial cable with an F standard connector . If the F standard connectors are not yet tted on the cables, strip the insulation from the cables as shown in the following illustration and carefully screw the F standard connectors on to the ends of the cables until [...]

1 1 Information about antenna connection and loop-through mode T o enable you to utilise all the reception and recording features of your UFS 922 twin-PVR HDTV Sat receiver , such as 1. Recording one programme and simultaneously viewing any other programme or zapping through the channels, and 2. Recording two different programmes at the same time, [...]

12 Connection and setup Connection example Conventional DiSEqC™ system ~ Hi- system Network PC/laptop Dolby Digital system External hard disk Connection sequence for single-cable matrices[...]

13 Connection and setup Connect the satellite receiver (HDMI or alternatively TV Scart socket) and the TV set using an HDMI or Scart cable (see “Connection example”). If your TV is stereo, you can receive the sound in stereo via the HDMI or Scart connection. For system reasons, the same video signals are to be found at the TV Scart socket as at[...]

14 Connection and setup First Installation Required buttons on remote control for rst installation:  ...  Numerical input  (green) Proceed to next step in rst installation  (red) Go back one step in the rst installation  Conrm the changed values/setting  Select/change individual menu parameters, navigation  Cancel i[...]

15 Connection and setup The following display appears: Use the  buttons here to select the basic settings for the video and audio output from the receiver to the TV set. For this, refer to the operating manual for your TV set and take care to select only those settings that your TV set can process. Video Output via Select the connection on the r[...]

16 Audio format via HDMI Here you can select the type of audio signal that is transmitted by the HDMI interface. Select the signal that your TV set can process: - Decoded PCM or - S/PDIF format Auto Dolby Digital output Here you can select whether the receiver should automatically select the Dolby Digital soundtrack (if this is transmitted). TV Sca[...]

17 Separated: The second tuner input of the receiver , identied at the rear of the unit by “LNB2 in”, receives its own signal input (i.e. there is a direct connection between the antenna socket and tuner input 2). See example illustration on the right. Before you start conguring the tuner for your type of reception system you must rst [...]

18 The following conguration options are available for: T uner 2 Connection type “Loopthrough”: All settings are made on tuner 1. The second tuner is fed from the looped through output of the rst tuner . Available settings for tuner 1 are: “DiSEqC™1.0”, “DiSEqC™1.1”, “Motorized Antenna” and “Simple LNB” T uner 2 Connec[...]

19 Connection and setup The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display appears: Select Satellites - T uner 1 Here, you can select up to four ava[...]

20 Connection and setup The following display appears: Satellite Conguration - T uner 1 Make the settings for the rst satellite for tuner 1 here. LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types[...]

21 Connection and setup 22 kHz signal: Y ou only need to specify this data if your LNB type is “Simple”. The 22 kHz signal is needed to switch LNBs in multi-feed reception and to switch between Low and High band. - On - Off T est-T ransponder: Select the “T est-T ransponder” eld. Here you can select a transponder for checking whether you[...]

22 Connection and setup The following display appears: Select Satellites - T uner 1 Here, you can select the available satellites (max. 64) included in the signal on tuner 1. Use the  buttons to select the satellite you want and conrm your selection with the  button. The selected satellites will be identied with a tick. When you have co[...]

23 Connection and setup LNB frequency (MHz): Y ou only need to specify this data if your LNB type is not “Universal LNB”. The data required dif fer for the settings “Simple” and “User-dened”. Refer to the documentation supplied for your LNB. - Selection “Simple” LNB: Use the numeric keypad to enter the LNB frequency - Selection ?[...]

24 Connection and setup The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Motorized Antenna (DiSEqC™1.2/DiSEqC™1.3) Press the  (green) button. The following displ[...]

25 Connection and setup The following display appears: Motor Control Select the control type “DiSEqC™1.2”. Refer to the documentation for your motorized antenna for details. Go to Null Position Select the “Go to Null Position” eld. Press the  button to instruct the turntable to move to its null position. Set Borders Select the “Se[...]

26 Connection and setup The following display appears: LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal - Simple or - User-dened LNB frequency (MHz): Y ou only need to specify this dat[...]

27 Connection and setup Set the turntable so that both of the bars “Signal-Strength” and “Signal-Quality” on the right of the screen show the highest available percentage values. T est-T ransponder: Select the “T est-T ransponder” eld. Here you can select a transponder for checking whether your settings are correct using the signal s[...]

28 Connection and setup Set Borders Select the “Set Borders” eld. In this menu you can set the limits for your turntable. This is particularly necessary if the turntable has only a restricted range in which it can turn before striking an obstruction (such as a wall or tree). Press the  button. The following display appears: The following [...]

29 Connection and setup The following display appears: LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal - Simple or - User-dened LNB frequency (MHz): Y ou only need to specify this dat[...]

30 The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Simple LNB Press the  (green) button. Connection and setup The following display appears: Select Satellite - T un[...]

31 Connection and setup LNB T ype: If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal - Simple or - User-dened LNB frequency (MHz): Y ou only need to specify this data if your LNB type is not “Un[...]

32 Use the  buttons to select “On” in the “OneCable System used” line. Then use the  buttons to switch to the “OneCable System” eld. The following display appears: Use the  buttons to select the one cable system used in your reception system: - EXR ... / EXU ... For all Kathrein one cable matrices - UAS 481 For the [...]

33 Connection and setup The following display appears: Select Satellites - T uner 1 Here you can select up to two satellites included in the signal on tuner 1. Use the  buttons to select the satellite you want and conrm your selection with the  button. The selected satellites will be identied with a tick. When you have completed all set[...]

34 When you have completed all settings, press the  (green) button. The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display appears: Protect the channel with a PIN: If your one cable system allows the transmission frequency to be[...]

35 Connection and setup The following display appears: LNB type (settings): If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal - Simple or - User-dened LNB frequency (MHz): Y ou only need to specif[...]

36 Refer to the documentation supplied with the UAS 481 for the settings for “T uner 1” and “T uner 2”. No frequency can be used by more than one receiver . The receivers would interfere with each other . Do not assign the same frequencies/channels to tuner 1 and tuner 2. Connection and setup The individual items are selected using the ?[...]

37 Connection and setup T ransmission channel for tuner 1: Select a free available transmission channel (SCR 0 - SCR 3). T ransmission channel for tuner 2: Select a free available transmission channel (SCR 0 - SCR 3). When you have completed all settings for the satellite, press the  (green) button. The following display appears: T est-T ranspon[...]

38 Connection and setup OneCable System - user-dened The following display appears: Select Satellites - T uner 1 Here you can select up to two satellites included in the signal on tuner 1. Use the  buttons to select the satellite you want and conrm your selection with the  button. The selected satellites will be identied with a tick.[...]

39 Connection and setup The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display appears: Make the settings for the second tuner in the same way as for the rst tuner . Protect the channel with a PIN: If your one cable system allow[...]

40 The following display appears: LNB type (settings): If your reception system does not have a Universal LNB, use the  buttons to select the LNB types that are used in your reception system. Y ou can choose from the following LNB types: - Universal - Simple or - User-dened LNB frequency (MHz): Y ou only need to specify this data if your L[...]

41 Channel Search The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons. If you do not want to perform a channel search, press the  (green) button and continue with the chapter “Date and T ime”. If you want to perform a channel search, use the  buttons to select[...]

42 Connection and setup Network Search Use the  buttons (On/Off) to select whether a network search should be performed. If you set the network search to “Of f”, only the factory default transponders for the satellite(s) you previously selected will be searched for new as yet unsaved channels. If you set the network search to “On”, th[...]

43 Date and Time The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons. Connection and setup Time Setup Here you can select whether the time information should be obtained by the receiver automatically from a specic channel that you select or whether the time information [...]

44 Automatic Manual Y ou need not input any further data, the receiver will automatically update the date and time. Use the numeric keypad or the  buttons to input the correct date. Then use the  buttons to switch to the “Time” eld and use the numeric keypad or the  buttons to input the correct time. Then use the  button[...]

45 General operating instructions T opic Page Alphanumeric inputs ..................................................................................................................................................... 45 Editing and selection options in the menus ........................................................................................[...]

46 General operating instructions After you have input the desired term, press the  button to enter the name/search expression or press the  or  button to cancel the input.  Switch between upper case and lower case letters  Conrm the term input  Cancel input without saving  Cancel input without saving Always pay attention to[...]

47 General operating instructions Explanation of symbols in receiver display V arious symbols are occasionally shown in the receiver display above the normal display (channel name). These are not displayed permanently , they only appear for specic functions, procedures or channel features. Y ou can nd their meaning in the table below . This s[...]

48 Basic operation in TV or Radio mode (live operation) Remote control for live operation (TV/Radio)  = Call up favourites list  = Not currently supported V olume “-” (softer) V olume “+” (louder) Select T eletext Operation (on)/Standby (off) Call up the Help function Numeric keypad Select main menu Mute Call up EPG (Electronic Progra[...]

49 Basic operation in TV or Radio mode (live operation) Switching between TV and Radio operation Adjusting the volume Channel selection Channel selection from the channel list T o switch between TV and radio mode, press the  (blue) button. The volume is adjusted using the  buttons. The  button allows the channel to be selected from the [...]

50 Now use the relevant coloured button to select the category from which you want to open a channel list: Channel list selection: Use the  buttons to scroll through the currently available channel lists. If you want to see an overview of the currently available channel lists, press the coloured button for the selected category again; you wil[...]

51 Channel Information Channel information is shown for a few seconds each time the channel is changed (this can be changed under “Settings”, “User-Dened Settings”, “Customise Screen Menu”) or displayed continuously by pressing the  button. Broadcaster logo Channel slot in the selected channel list/ favourites list Selected Favour[...]

52 Calling up the channel options If the channel OSD contains the following icon , this is a portal channel. Press the  (yellow) button, use the  buttons to select “Channel Options” and press the  button to conrm your selection. The following display then appears (example): Use the  buttons to select your desired channel op[...]

53 Select Audio T rack If the channel banner displays 1/3 in front of the symbol for the selected soundtrack, this tells you that you have currently selected the rst of the three available soundtracks. Press the  (yellow) button, use the  buttons to select “Select Audio T rack” and press the  button to conrm your selection. Th[...]

54 T eletext This symbol in the channel information shows you whether T eletext is available for the selected channel. When you press the  button, the receiver processes the T eletext service data for your TV set to display , even when the signal is encrypted. During the search, the page which is being searched for is displayed in the top left-h[...]

55 One-T ouch Recording (OTR) Basic operation in TV or Radio mode (live operation) T o start recording directly to the hard disk, press the  (red dot) button. The following display appears (example): Use the  buttons to select the lines to be changed; make the changes using the  buttons. Recording: Y ou have the following selection o[...]

56 Premium EPG Y ou will only see information on the current or subsequent programmes in the EPG if this data is supplied/transmitted by or by the channel provider . If no EPG data is available, the receiver shows the message “No data available” instead of showing information on the current program. General information about Premium EPG What Pr[...]

57 Premium EPG Calling up the EPG The EPG is opened by pressing the  button. Y ou will automatically see the view you selected in the menu (“Settings”, “User-Dened Settings”, “EPG Settings”) - irrespective of which view you selected last time before exiting the EPG. The following display appears (example): Selected view of EPG Cha[...]

58 Premium EPG -  (red) button Open the timer list (display of all pre-programmed recordings/reminders) -  button Navigation in the individual views (e.g. 15 minutes skip forward in the “Current” view) -  (yellow) button Open a preview of the currently selected channel (programme listings) -  (blue) button Open the category selec[...]

59 Premium EPG Views of the EPG “Current” View The “Current” view can be called up at any time in EPG by pressing the  (green) button. In the “Current” view you can see all channels displayed in the order of the overall channel list. Provided that EPG data has been supplied/transmitted by or by the channel provider , the receiver sho[...]

60 Premium EPG “Coming up” view (programme listings) The “Coming up” view can be called up at any time in EPG by pressing the  (yellow) button. In the “Coming up” view you will see all the programmes that will be shown on the channel previously selected in the “Current” view . Provided that EPG data has been supplied/transmitted [...]

61 Premium EPG Categories view The “Coming up” view can be called up at any time in EPG by pressing the  (blue) button. In the “Categories” view you can see all programmes, sorted by category and start time. The following main categories are available for selection: Pick of the day , My hints (see “Extras menu”), Movies, Entertainmen[...]

62 Premium EPG Y ou can create your own categories within this section. Press the  button to activate the input eld. Now you can enter the search expression/category name for your new category . Alphanumeric characters are input as described in “Operating instructions”, “Alphanumeric entries”. T o search the available programmes for o[...]

63 Premium EPG In this section you have the facility to select an actor that is shown in the Actors list (using the cursor (  ) buttons) and the by pressing the  button to search through all available data for programmes in which this person appears. If there are programmes available for which the name of this person appears in the informatio[...]

64 Search function Premium EPG The search function can be called up in EPG at any time by pressing the  button. The following display appears (see screenshot on the right). Y ou have the following search options: - Further programme times for the currently selected programme (in the example on the right “King of Queens”) - Actor: Select the [...]

65 Premium EPG Full text search After calling up the search function, press the  button again to gain access to the full text search. The following display appears (see example on the right): If necessary the last search expression used is offered. Pressing the  button allows you to delete your input or a search expression provided by the rec[...]

66 Premium EPG Recording settings (programming the timer) The  (red dot) button allows you to set a programme for recording at any time. The programme to be recorded can be selected in any of the EPG views, provided the  (red dot) button appears at the bottom of the screen display . Programme appears in EPG: Select the desired programme and p[...]

67 Information on direct decryption using timers (recordings on encrypted channels): The “Decrypt” eld only appears when recording encrypted channels. If you want to make the recording unencrypted, use the  buttons to select “Y es”; if you want the recording to be made encrypted on the hard disk, select the “No” option. When do[...]

68 Recording “Once” Use the  buttons to select the “Once” recording mode (see screenshot on the right). Use the  buttons to switch to the “Date” eld and use the  buttons to select the desired recording day . Use the  buttons to switch to the “Start” eld and use the  buttons or the number buttons t[...]

69 Premium EPG Recording “Daily” Use the  buttons to select the “Daily” recording mode (see screenshot on the right). Use the  buttons to switch to the “Start” eld and use the  buttons or the number buttons to select the desired recording start time. Use the  buttons to switch to the “End” and eld use t[...]

70 Premium EPG Recording “User-Dened” Use the  buttons to select the “user-dened” recording mode (see screenshot on the right). Use the  buttons to switch to the “Day” eld and use the  buttons to select the required day for the recording. Press the  button to x the selection (the day will be shown in red[...]

71 Premium EPG Reminder function (switch over to programme) If you want to be reminded that a programme is about to start, you can activate the reminder function for the desired programme. The reminder function is set up in exactly the same way as programming a recording. The only dif ference is that the entry in the “Recording” line must be ?[...]

72 Premium EPG Timer list view The “T imer list” view can be called up at any time in EPG by pressing the  (red) button. The following display appears (example): The timer list view shows you all the recordings and reminders that are scheduled (marked green). The  buttons allow the recordings to be sorted into “Once” or “Repeated[...]

73 Premium EPG When editing a recording, you can change all parameters apart from the recording mode. Make the changes using the cursor (  ) buttons and the numeric keypad. Press the  button to conrm your changes, and return to the timer list view . Editing a recording If your scheduled recordings overlap, the timer list view for the recei[...]

74 Editing the channel list Calling up the “TV -Channellist” menu T opic Page Y ou have two ways of accessing the edit menu for the channel lists: 1. Directly via the channel list • On the TV picture, press the  button to open the channel list • Then press the  (red dot) button or 2. Using the “Edit channel lists” option in the ma[...]

75 In the following chapter we have chosen to use the rst option to explain the editing of the channel lists. The following display appears (example): Selecting the channel list/favourites list to be edited Now use the relevant coloured button to select the desired channel list category (refer to the “Basic operation in TV or Radio mode (live [...]

76 Selecting the channels to be edited Select a channel in the selected channel list/favourites list using the cursor (  ) buttons (see example screenshot on the right). T o select several channels to be edited at the same time, if they are not listed directly following each other in the selected channel list, use the cursor (  ) buttons to s[...]

77 Move Use the  buttons to select “Move” and conrm your selection with the  button. The following display appears (see example screenshot on the right): Now use the cursor (  ) buttons or the numeric keypad to select the new channel memory position(s), then conrm the insertion with the  button. Delete Use the  button[...]

78 Lock Use the  buttons to select “Lock” and conrm your selection with the  button. T o lock the channel you must now enter your four-digit PIN code (factory setting: 0000). The following display appears (see example screenshot on the right): The locked channel is now displayed in the channel list with a padlock on the right hand s[...]

79 If several channels use the same data, the following warning message is displayed when you deactivate the function (see screenshot on right). In this case, no data is stored for the other affected channels. Y ou can only use this function if Premium EPG data is available for the selected channel. Use the  buttons to select “tvtv off” o[...]

80 Editing channels (favourites lists) After selecting the channel(s) to be edited, press the  (red dot) button. The following display appears (see screenshot on the right). “Start Blockselection” only appears if just one channel has been selected for editing. Move See “Editing channels (channel lists)” “Move”. Remove from favoriteli[...]

81 Recording archive (play back/edit recordings) T opic Page Calling up the recording archive The recording archive is called up by pressing the  button or the  button. Each time the EPG is opened, you will automatically be shown the view you had selected the last time you exited the archive. The following display appears (example): Recording[...]

82 Recording archive (play back/edit recordings) -  (red) button Call up the chapter view or the automatic creation of chapters (if not yet available) -  (green) button Call up ordering of recordings (ordered by date, ordered by title and ordered by duration) -  (yellow) button Display the recordings by channel -  (blue) button Display [...]

83 Views of the recording archive (sorting the recordings) Recording archive (play back/edit recordings) When displaying the recordings you have the following sorting/display options: -  (green) button Ordered by date (you can use the  buttons to choose between the sorting criteria of date, title or duration (recording length)) -  (yell[...]

84 Recording archive (play back/edit recordings) Folders in the recording archive From software version 1.02, the UFS 922 includes the option of creating folders in the recording archive. Y ou can give these folders the names of your choice and add recordings to them. Creating folders Use the  buttons to select any recording and then press th[...]

85 Recording archive (play back/edit recordings) Use the  buttons to select the desired recording. Conrm selection of the desired recording by pressing the  button. Pressing the  button again exits the recording archive and allows the desired recording to be viewed in full-screen mode. Playback starts at the last playback position. I[...]

86 Recording archive (play back/edit recordings) Y ou will see this display after starting playback of the recording in full- screen mode or by pressing the  button once Y ou will see this display during all types of fast forward/rewind or by pressing the  button or  button o OK button Call up the recording archive during playback. The pla[...]

87 Recording archive (play back/edit recordings) Selecting the recordings to be edited T o select a recording, select the desired recording in the selected sort list, using the cursor (  ) buttons (see example screenshot on the right). If the relevant recording is stored in one of the folders you have created, rst select the folder containing[...]

88 Recording archive (play back/edit recordings) Delete Use the  buttons to select “Delete” and conrm your selection with the  button. The selected recording(s) will be deleted. Deleted recordings are irrevocably deleted and can only be restored by re-recording the programme! Lock Use the  buttons to select “Lock” and con?[...]

89 Recording archive (play back/edit recordings) Changing the category Use the  buttons to select “Change category”. Now use the  buttons to select the desired category (see example screenshot on the right), to which the recording(s) should be assigned. Conrm your selection with the  button. If no appropriate category is avail[...]

90 Recordings: cut, split, copy Use the  buttons to select “Recording”. Now use the  buttons to select the desired action (see example screenshot on the right) and conrm your selection using the  button. Before cutting or splitting a recording for the rst time you should make a copy of the recording to be edited, so that if[...]

91 Recording archive (play back/edit recordings) The following display appears (example): Now use the cursor (  ) buttons, the  buttons or the  button to select the desired start of the section to copy and then conrm by pressing the  button. The following display appears (example): Now use the cursor (  ) buttons, the  bu[...]

92 Recording archive (play back/edit recordings) Cut The following display appears (example): Now use the cursor (  ) buttons, the  buttons or the  button to select the desired start of the section to be cut from the recording, and then conrm by pressing the  button. The following display appears (example): Now use the cursor ( ?[...]

93 Recording archive (play back/edit recordings) Split The following display appears (example): Now use the cursor (  ) buttons, the  buttons or the  button to select the desired time at which the recording should be split, and then conrm by pressing the  button. The following display appears (example): Use the  buttons to s[...]

94 Moving to a folder Y ou can use this function to move the recording selected before calling up the edit menu to a folder you have created. Use the  buttons to select “Move to folder ...”. Then press the  button. The currently available folders are displayed. Use the  buttons to select the desired folder and conrm by pressin[...]

95 Copying to USB data carrier Use the  buttons to select “Copy to USB Device” and conrm your selection with the  button. The following display appears (example): The connected USB data carrier must be “F A T/F A T 32” formatted. Successful USB data carrier initialisation is indicated by the “USB” and “HDD” symbols on th[...]

96 Note: When the chapter view is called up, the receiver automatically creates seven chapters for the recording you select, if this has not already been done. This function is not performed if you have already created chapters manually . Use the  buttons to select the desired chapter . T o start playback from the selected chapter , press the[...]

97 Deleting chapters Deleting a chapter: Use the  buttons in the chapter overview to select the chapter to be deleted, and press the  (red dot) button. The following display appears (see screenshot on the right). Use the  buttons to select “Delete” and conrm your selection with the  button. The selected chapter is deleted. [...]

98 Main menu T opic Page Calling up the main menu and introduction The main menu is opened by pressing the  button. The following display appears: The programme showing on the currently selected channel always appears in the top right-hand corner of the main menu. The selected menus, sub-menus and items, as well as the parameters to be set, are [...]

99 Main menu Menu overview Main Menu (call up by pressing the c button) Edit channel lists Channel search Service menu Settings Interfaces Applications Language selection Automatic search Automatic software update First installation (see “Connection and Set-Up”, “First installation” chapter) Common Interface Start FTP when starting receiver[...]

100 Main menu - Channel search Automatic Channel Search After calling up the menu you will see the following display: Y ou have three different search options: - Automatic Channel Search - Manual Channel Search - Search with service ID Use the  buttons to select the desired search type and conrm your selection using the  button. After c[...]

101 Network Search Use the  buttons (On/Off) to select whether a network search should be performed. If you set the network search to “Of f”, only the factory default transponders for the satellite(s) you previously selected will be searched for new as yet unsaved channels. If you set the network search to “On”, the transponder networ[...]

102 Manual Channel Search Main menu - Channel search After calling up the menu you will see the following display: The  buttons allow you to select different sets of parameters for the search. Satellite Use the  buttons to select the satellite on which the transponder you want to search is located. By pressing the  button at this poi[...]

103 Search with service ID Main menu - Channel search Symbol Rate Use the numeric keypad to enter the relevant symbol rate. Channel search mode Use the  buttons to select the type of channels that are to be searched for . Y ou have three options: - “free & scrambled” All channels are searched for - “only free” Only free-to-air cha[...]

104 Note: Y ou can cancel the search at any time by pressing the  button. The following displays during and in connection with the search are identical to those for the automatic search. T ransponder Frequency Use the  buttons (transponder frequency already saved) or the keypad (transponder frequency not yet saved) to select the transponde[...]

105 Main menu - Service menu After calling up the menu you will see the following display: Y ou can choose between various different menus: - Automatic Software Update - Software Update - Software update by USB - Factory Reset In addition, the following information is displayed in the service menu under the “Factory Reset” option: - Operating s[...]

106 Main menu - Service menu If new software or changes to the channel list are found, you will see the following display the next time you start the UFS 922: Press the  button to perform the software update. After the software update, you will see the following display (only if there are any changes to the delta channel list): Press the  but[...]

107 After calling up the menu you will rst see the following display: Software Update The following display then appears: Use the  buttons to select the parameters to be updated during the update procedure. Show Infotext: Press the  button to display the info text for the available downloads. These indicate the main features of the new [...]

108 Main menu - Service menu Follow all on-screen instructions! Check the time setting following a software update! Y ou can also download the updates from the Internet. The address is: http://www.kathrein.de Y ou will nd the software at “Service” → “Software and Download” → “Receiver” → “UFS 922” These updates can be perfo[...]

109 After calling up the menu you will rst see the following display: Y ou can here restore the channel list and the installation settings to the factory settings. Y ou can use the  buttons to select the components to be restored to their factory settings. In each case use the  buttons to select “Y es or No”. In addition you can [...]

1 10 Main menu - Settings Basic settings After calling up the menu you will see the following display: Y ou can choose between various different menus: - First Installation - Basic Settings - User Dened Settings - Antenna & Satellite Use the  buttons to select the desired menu and conrm your selection using the  button. First ins[...]

1 1 1 TV Settings After calling up the menu you will see the following display (depending on the selected signal output): For output of the TV picture via the HDMI output: For output of the TV picture via the Scart-TV output: The individual items are selected using the  buttons. Changes to the current settings can be made using the  but[...]

1 12 Audio Settings TV -Scart-Output Select the type of video signal to be output at the TV Scart socket here . Select the signal that your TV set can process. Either - RGB (Red/Green/Blue signal) - Y/C (S-Video signal (luminance/chrominance), or - CVBS (Colour Video Baseband Signal) VCR-Scart-Output Select the type of video signal to be output at [...]

1 13 Preferred Subtitle Language Select here your preferred subtitles language. Y ou can choose between the following languages: Deactivated (off), German, English, French, Italian, Spanish, Czech, Dutch, Polish, Turkish or Russian. Audio Format via HDMI Here you can select the type of audio signal that is transmitted by the HDMI interface together[...]

1 14 Clock Change (Summer Time) Here you can select whether the receiver should automatically change over to and from summer and winter time. The “Manual” setting only makes sense if you also selected “Manual” for the selection item “Time setup”, since otherwise the time information is obtained automatically by the receiver . Either - A[...]

1 15 Setting the remote control code Main menu - Settings After calling up the menu you will see the following display: Y ou can now use the remote control for your receiver to set a new remote control code (the remote control code 1 is set as standard). Simultaneously press buttons: -  +  + 1 for remote control code 1 -  +  + 2 for rem[...]

1 16 Parental Lock User Dened Settings Fan Settings Main menu - Settings Use the  buttons to set the desired fan speed (revolutions per minute). Either - Fast (1500 rpm) - Medium (1000 rpm) - Slow (500 rpm) The fan speed should be adjusted to the temperature changes in the receiver . After calling up the menu you will see the following dis[...]

1 17 Main menu - Settings The following display then appears: In this menu you can set various restrictions/parental controls. The individual items are selected using the  buttons. The changes to the current settings can be made using the  buttons or the numeric keypad. Lock Mainmenu Select here whether the main menu should be locked. I[...]

1 18 Main menu - Settings Customize Screen Menu After calling up the menu you will see the following display: The individual items are selected using the  buttons. The changes to the current settings can be made using the  buttons or the numeric keypad. Sleep Timer Y ou can use the “Sleep Timer” function to set an inactive time peri[...]

1 19 Main menu - Settings EPG Setup After calling up the menu you will see the following display: The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. EPG Grabbing Select here the data with which the EPG should be updated/lled. In order to exploit [...]

120 Recording settings After calling up the menu you will see the following display: The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons. Automatic Timeshift Select here whether automatic time-shifting is enabled or disabled. If this is set to “On”, the receiver automa[...]

121 Antenna & satellites (settings) Main menu - Settings After calling up the menu you will see the following display: If you do not have a meter for adjusting your reector , you can use the sat nder as an alignment aid. However the sat-nder is not a complete substitute for a meter . The individual items are selected using the  b[...]

122 Main menu - Settings FEC Select the applicable error rate (V iterbi rate). Y ou need not state the error rate for the DVB S(SD) transponders. Instead a xed display of “Automatic” appears. Y ou must state the correct error rate for the DVB S2(HD) transponders. Either QPSK 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 or 8PSK 2/3, 3/4, 3/5, 5/6,[...]

123 Frequency Select here the desired transponder . By pressing the  button at this point you can view a list of the transponders saved in the receiver for this satellite. Use the  buttons to select the transponder you want and conrm your selection with the  button. Symbol Rate The symbol rate is positively assigned to each saved transp[...]

124 Delete Satellites Press the  button to delete the currently selected satellite. As a security feature you are asked to conrm again by pressing the  button that you really want to delete the satellite. Edit Satellite Name By pressing the  button you can call up the input screen which allows you to change the name of the currently sel[...]

125 After calling up the menu you will see the following display: The individual items are selected using the  buttons. If you need to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Edit T ransponders Satellite Name Select here the satell[...]

126 Main menu - Settings Symbol Rate The symbol rate is positively assigned to each saved transponder , and cannot be changed. Polarization The polarization is positively assigned to each saved transponder , and cannot be changed. Edit transponders By pressing the  button you can call up the input screen which allows you to edit/change the setti[...]

127 Add a new transponder By pressing the  button you can call up the input screen to save a new transponder . The following display appears: Frequency: Use the keypad to enter the transmission frequency for the new transponder . DVB T ype: Select here whether the selected transponder is to receive standard channels (DVB-S (SD)) or HDTV channels[...]

128 Always follow the operating instructions from your Pay-TV provider and the instructions supplied with the Smartcard and the CA module! Smartcards and CA modules are not included with this product! The cards and modules are issued by the respective pay TV providers, and contain the subscriber data and details of the channels for which the subscr[...]

129 Main menu - Interfaces (CI, hard disk and network) Y ou can nd out which Conditional Access modules are in the CI slots on the UFS 922 and which Smartcard is in which CA module from the “Mainmenu” under “Interfaces”, and the “Common Interface” menu. Conrmation is by pressing the  button. The screenshots below depend on the [...]

130 Main menu - Interfaces (CI, hard disk and network) Information for Conax, SECA, Viaccess and CryptoW orks users: Note that with monthly activation intervals, the channel providers have different procedures for activating pay TV cards. Activation may therefore be a few days before or after the beginning of a new month. During this activation per[...]

131 Main menu - Interfaces (CI, hard disk and network) HDD Management After calling up the menu you will see the following display: Y ou have the following selection options: - Format Record Archive (delete) - Format Media Archive (delete) Use the  buttons to select the desired action. Deleted data cannot be restored - it is irrevocably delet[...]

132 Main menu - Interfaces (CI, hard disk and network) Ethernet Settings After calling up the menu you will see the following display: These settings should not be made unless the receiver is linked into a network or is linked to a PC/laptop using a crossed over network cable. The Ethernet interface used in the receiver is a 10/100 base T Ethernet [...]

133 If with the “DHCP On” setting no connection can be established between the receiver and DHCP server/router , switch the setting to “DHCP Off” and make the setting as described for (DHCP “Off”). Conguration example: Receiver: IP address: 192.168.0.1 1 Subnet Mask: 255.255.255.0 PC/Laptop: IP address: 192.168.0.10 Subnet Mask: 255.[...]

134 Main menu - Applications This menu displays applications that are installed on your UFS 922. This menu allows you to start and stop these applications. T o do this, follow the instructions displayed and the explanations on the menu. Any modications to the receiver software, or the use of applications not provided by Kathrein, will invalidate[...]

135 Main menu - Language settings After calling up the menu you will see the following display: Use the  buttons to select the desired menu language and conrm your selection using the  button. The following languages are available for selection: German, English, French, Italian, Spanish, Czech, Dutch, Polish, T urkish and Russian. The s[...]

136 T uner Conguration T opic Page Call up the tuner conguration/T uner conguration general The main menu is opened by pressing the  button. Use the  “Settings” buttons and conrm by pressing the  button. Select the  “Antenna & satellite” buttons and conrm by pressing the  button. Use the  “T u[...]

137 Separated: The second tuner input of the receiver , identied at the rear of the unit by “LNB2 in”, receives its own signal input (i.e. there is a direct connection between the antenna socket and tuner input 2). See example screenshot on the right. T uner Conguration Before you start conguring the tuner for your type of reception sy[...]

138 The following conguration options are available for: T uner 2 Connection type “Loopthrough”: All settings are made on tuner 1. The second tuner is fed from the looped through output of the rst tuner . Available settings for tuner 1 are: “DiSEqC™1.0”, “DiSEqC™1.1”, “Motorized Antenna” and “Simple LNB” T uner 2 Conne[...]

139 T uner Conguration DiSEqC™1.0 The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Satellite 1 Select “Satellite 1:***” eld and press the  button to allo[...]

140 LNB Setting: Select the “LNB Setting” eld. If your reception system does not have a Universal LNB, press the  button so that you can make the settings for the LNB. Y ou can choose from the following LNB types: - Universal - Simple - User-dened T uner Conguration If your LNB is neither a Universal nor a Simple LNB, select the set[...]

141 DiSEqC™1.1 The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. T uner 1 Select “Tuner 1” eld and press the  button to allow you to make the settings for th[...]

142 LNB Setting: Select the “LNB Setting” eld. If your reception system does not have a Universal LNB, press the  button so that you can make the settings for the LNB. Y ou can choose from the following LNB types: - Universal - Simple - User-dened T uner Conguration If you select “Universal” you need make no further settings. If[...]

143 Motorized Antenna T uner Conguration The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Press the  button. The following display appears: Use the  buttons[...]

144 T uner Conguration Motorized Antenna (DiSEqC™1.2) The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Motor Control Select the control type “DiSEqC™1.2”. Re[...]

145 Select Satellites Select the “Select Satellites” eld. Select here which satellites you want to receive via your turntable. Pressing the  button presents a display of the satellites stored in the receiver: Use the  buttons to select the satellites to be received and conrm your selection in each case using the  button. The sele[...]

146 Stop on Signal: Select the “Stop on Signal” eld. Here, you can select whether the motorized antenna should stop its rotary movement immediately on reception of a signal from the desired satellite. Y ou can choose between “On” and “Of f”. Move Motorized Antenna: Select the “Move Motorized Antenna” eld. Here you can control [...]

147 Set Borders Select the “Set Borders” eld. In this menu you can set the limits for your turntable. This is particularly necessary if the turntable has only a restricted range in which it can turn before striking an obstruction (such as a wall or tree). Press the  button. The following display appears: The following buttons allow you to[...]

148 Select Satellites Select the “Select Satellites” eld. Select here which satellites you want to receive via your turntable. Pressing the  button presents a display of the satellites stored in the receiver: Use the  buttons to select the satellites to be received and conrm your selection in each case using the  button. The s[...]

149 T uner Conguration Simple LNB The individual items are selected using the  buttons. If you require to access submenus, they can be called up using the  button. Changes to the current settings can be made using the  buttons or the numeric keypad. Satellite and position: Select here the satellite you desire from the available sa[...]

150 Use the  buttons to select “On” in the “OneCable System Used” line. The following display appears: Press the  button. The following display appears: Use the  buttons to select the one cable system used in your reception system: - EXR ... / EXU ... For all Kathrein one cable matrices - UAS 481 For the Kathrein one cable LN[...]

151 T uner Conguration OneCable System - EXR ... / EXU ... After calling up the menu you will see the following display: Press the  button to access the system settings. The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display [...]

152 Make the settings for the second tuner in the same way as for the rst tuner . T uner Conguration Then press the  button. Number of Satellites Select the “Number of Satellites” eld and set the number of satellites to be received by your reception system. A maximum of two satellites can be received. Satellite 1: .... Select the ?[...]

153 T uner Conguration The following display appears: Y ou can choose from the following LNB types: - Universal - Wideband - User-dened If your LNB is neither a Universal nor a Wideband LNB, select the setting “User-dened”. The “User-dened” setting means you must manually set the frequency ranges that are congured for your LN[...]

154 T uner Conguration OneCable System - UAS 481 After calling up the menu you will see the following display: Press the  button to access the system settings. The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display appears: T[...]

155 The following display appears: Satellite and position: Select here the satellite you desire from the available satellites. By pressing the  button at this point you can view a list of the satellites saved in the receiver . Use the  buttons to select the satellite you want and conrm your selection with the  button. Use the  but[...]

156 T uner Conguration User-dened After calling up the menu you will see the following display: Press the  button to access the system settings. The individual items are selected using the  buttons. Changes to the current settings can be made using the  buttons or the numeric keypad. The following display appears: Protect the c[...]

157 T uner Conguration Then press the  button. Y ou will be asked whether you want to save the changes. Use the  buttons to select “Y es, save the changes” and confirm with the  button. If a connection to the one cable system cannot be established, check your settings (frequency and transmission channel) and if necessary call for[...]

158 T uner Conguration Y ou can choose from the following LNB types: - Universal - Wideband - User-dened If your LNB is neither a Universal nor a Wideband LNB, select the setting “User-dened”. The “User-dened” setting means you must manually set the frequency ranges that are congured for your LNB. Select the frequency range t[...]

159 Multimedia Press the  button to call up the multimedia menu. In addition to the familiar FTP server functionality from software version 1.01 for transferring data (recordings and pictures) via the network, from software version 1.02 the UFS 922 provides more extensive network functions. o UPnP server functionality (e.g. streaming of UFS 922 [...]

160 Multimedia The UFS 922 can operate as both a UPnP media client and a UPnP media server . Further information about UPnP can be found on the Internet at “www .upnp.org”. UPnP media client: Streaming from external devices to the UFS 922 UPnP media server: Streaming from the UFS 922 to external devices UPnP client/server functionality (UPnP = [...]

161 The Media Centre has an integral MP3 player . The MP3 specic information display is based on “IDT ag Info V2.3”. If this is not available, the le name is displayed instead of this information. Only les from the previously selected folder are played back. Use the  buttons to select the track with which you want to start your p[...]

162 Multimedia During playback, you have the following control options:  Pause  Start playback after pause  Next/previous track  Skip 30 seconds forwards or backwards  /  Cancels MP3 playback and displays the Media Centre T o change the settings for the MP3 player , press the  (yellow) button after selecting the rst tr[...]

163 Playback of XVID les functions in the same way as playback of an external recording (see “Playback of external recordings”). XVID playback Multimedia  Pause  Start playback after pause; show/hide playback banner  10 % jumps forwards/back in recording  Skip 30 seconds forwards or backwards  Available fast forward s[...]

164 Operation from the front panel (without remote control) If you have misplaced your remote control, or if the batteries are at, you can still operate your receiver from the front panel. The front panel houses four buttons and the multifunction control (from now on referred to as “the control”). Record button: Press the Record button to st[...]

165 Operation from the front panel (without remote control) Performing the software update Y ou can also download the updates from the Internet. The address is: http://www.kathrein.de Y ou will nd the software at “Service” → “Software and Download” → “Receiver” → “UFS 922” 1. Use the remote control to switch the receiver in[...]

166 T roubleshooting In the event of a malfunction, rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables are connected to the receiver input 3. Receiver and TV set are correctly connected to each other by a HDMI or Scart or cinch cable 4. Audio connections are[...]

167 T echnical appendix T echnical specication T ype UFS 922si UFS 922sw Order no. 20210121 20210122 Colour Silver Black RF section Sat IF band MHz 950-2150 Input level band dBµV 44-83 Modulation, FEC, demultiplexer DVB-S/DVB-S2 standard Video resolution CCIR 601 (720 x 576 lines), 576p, 720p, 1080i Video decryption MPEG-2, MPEG-4-compatible In[...]

168 T echnical appendix Examples of one cable systems * ) The receiver must be programmed for one cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat-IF Sat-IF 1400 Can also be combined with EXR 5xx Sat-IF 950-2150 MHz[...]

169 T echnical appendix * ) The receiver must be programmed for one cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 * ) The receiver must be programmed for one cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12 Sat-IF 8 connections per living unit Sat-IF[...]

170 T echnical appendix * ) The receiver must be programmed for one cable commands ** ) Overvoltage protection KAZ 1 1/KAZ 12[...]

171 T echnical appendix Connection examples for network functionality PC/Laptop Gekreuztes Netzwerkkabel IP-Adresse: 192.168.0.10 IP-Adresse: 192.168.0.1 1 ~ DHCP (Receiver): OFF IP address: 192.168.0.1 1 IP address: 192.168.0.10 PC/laptop Crossed network cable[...]

172 T echnical appendix PC/Laptop Netzwerkkabel Switch/HUB TCP/IP-Adresse: 192.168.0.12 PC/Laptop Netzwerkkabel Netzwerkkabel TCP/IP-Adresse: 192.168.0.10 TCP/IP-Adresse: 192.168.0.1 1 ~ DHCP (Receiver): OFF TCP/IP address: 192.168.0.12 TCP/IP address: 192.168.0.10 TCP/IP address: 192.168.0.1 1 PC/laptop PC/laptop Switch/HUB Network cable Network c[...]

173 T echnical appendix PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) PC/Laptop Netzwerkkabel TCP/IP-Adresse: 192.168.0.13 TCP/IP-Adresse: 192.168.0.12 TCP/IP-Adresse: 192.168.0.1 1 TCP/IP-Adresse: 192.168.0.10 Netzwerkkabel Netzwerkkabel ~ ~ DHCP (Receiver): OFF Network cable Network cable Network cable Network cable DHCP server , [...]

174 T echnical appendix DHCP (Receiver): ON PC/Laptop Netzwerkkabel DHCP-Server , Router (z. B. Fritzbox) TCP/IP-Adresse: automatisch Funkstrecke ~ Network cable Radio link TCP/IP address: automatic PC/laptop DHCP server , router (e.g. Fritzbox)[...]

175 Comprehensive index Contents Preface............................................................................................................................................................................. 2 Difference between P AL and HDTV .....................................................................................................[...]

176 Comprehensive index Premium EPG ................................................................................................................................................. 56 General information about Premium EPG ..................................................................................................... 56 Calling up the EPG ...[...]

177 Comprehensive index Lock ................................................................................................................................................................................................ 88 Rename ......................................................................................................................[...]

178 Comprehensive index T uner Configuration ................................................................................................................................................... 136 Call up the tuner configuration/T uner configuration general ....................................................................................... 136 [...]

179 AC 3 Output for Dolby Digital signal ASTRA SES (Société Européene des Satellites) satellite system. Analogue and digital transponders in the frequency range 10.7-12.75 GHz. A V programme pos. Preferred programme slot on TV set for external connections such as Scart and HDMI CAM – Conditional Access Module Decryption decoder , which uses a [...]

180 HDMI – High Denition Multimedia Interface Digital interface for digital video and audio data transmission (preferred for HDTV). HDTV – High Denition T elevision High resolution television with a resolution up to 5 times higher or ner than P AL or NTSC. However , there is no compatibility , as the transmission process DVB-S2 and the[...]

181 Timer function Clock function for pre-programmed switch on and off times Timeshift function T ime shifted playback T ransponder A transponder is a frequency converter which receives TV and radio signals broadcast from the earth, converts them and the rebroadcasts them back to the earth at a different frequency . A satellite has several transpon[...]

182 Service If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly , or if unexpected problems occur , please contact your specialist dealer . The Kathrein Customer Hotline is also at your disposal. Phone: 0900/1 122240 * * (0.49 EUR per minute on Deutsche T elekom AG land line[...]

183 For your notes[...]

Internet: http://www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P .O. Box 100 444 • 83004 Rosenheim GERMANY 936.3382/A/0309/ZWT - T echnical data subject to change.[...]