Keys Fitness 502t manuale d’uso

Owner’ s Manual HEAL TH TRAINER 502t TREADMILL Customer Ser vice (888) 340-0482 K eys Fitness Pr oducts 4009 Distribution Drive Suite 250 Garland, TX 75041 www .keysfitness.com Model Name : 502t Serial Number : Purchase Date : Write down for future reference Serial Number Decal Location 415-00001 07/04[...]

T a ble of Contents Important Safety Information 3 Before Y ou S tart 4 Assembly 5-9 W arm Up Exercises 10 Moving Instructions 1 1 Power Requirements 12 Console Panel Functions 13 Program and Operation 14-15 Program Profiles 16 Belt Adjustment 17 Change to MPH or KPH 18 Maintenance Instructions 19 T roubleshooting Guide 20 Error Messages 21 Calibra[...]

Impor tant Safety Inf or ma tion W ARNING! Before using this treadmill or starting any exercise program, consult your physician. This is espe- cially important for persons over the age of 35 and/or persons with pre-existing health problems. The man- ufacturer or distributor assumes no responsibility for personal injury or property damage sustained [...]

Bef or e Y ou Star t Thank you for purchasing the HEAL TH TRAINER 502t T r eadmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise. Before you start, please read the Owner's Manual and become familiar with the operation of your new treadmill. Remember to take the time to perform the str etching[...]

Assembl y The HEAL TH TRAINER 502t treadmill will require assembly before operating. After opening the box, remove any packing material from the treadmill. Do not throw away any packing materials until the unit is working pr operly . Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet. Loca[...]

Assembl y Assembly requires the included allen wrench and your own phillips screwdriver . Do not plug in the power cord until all assembly step ar e completed. 1. W ith the treadmill deck in the down position, leave the unit on the original packing material to assemble all parts.Refer to figure 1. 2. Connect the Console Harness together . The harne[...]

Assembl y 7 Figure 4: Left and Right Upright Installation Figure 5: Upright Cr ossbar Assembly Figure 6: Hardwar e Installation 3. Install Left Upright and Right Upright to tread- mill base frame. Refer to Figure 4. Note: Make sure that the W ire Harness is not pinched. Do not install hardware until instructed. 4. Install the Upright Crossbar Assem[...]

Assembl y 8 8. Connect the Console Harness and Remote Speed Harness together as shown in Figure 7. Connectors snap together as shown in Figure 8. 9. Connect Ground W ire to grounding screw located on the side of the Upright Assembly using Screw ST4.2*13 (Qty . 1) as shown in Figure 7. CONSOLE GROUND WIRE SCREW ST4.2*13 CONSOLE HARNESS REMOTE HARNES[...]

Assembl y 9 10. Make sure all wires and harnesses are inside console housing and attach the console back cover to the Left and Right Upright mounting brackets using Screws ST4.2*16 (Qty . 6) as shown in Figure 9. 1 1. T ighten all hardware (previously installed) and insert Power Cable into AC connection on rear of unit. Refer to Figure 10. Figure 9[...]

W ar m Up Exercises T OE TOUCH STRETCH Stand bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your ham- strings, back of knees, and back. HAMSTRING STRETCH Sit with one leg extended. Brin[...]

Mo ving Instr uctions CAUTION! T O A VOID THE RISK OF INJUR Y , NEVER A TTEMPT TO MOVE THE TREADMILL WHILE IT IS IN THE UNFOLDED OPERA TING POSITION. T O REDUCE THE POSSIBILITY OF INJUR Y WHILE LIFTING , BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT . AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. IN ORDER T O RAISE OR LOWER THE TREA[...]

P ow er Requirements I MPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESUL T IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SER VICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERL Y GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT IF IT WILL NOT FIT THE OUTLET HA VE A PROPER OUTLET INST A[...]

Console P anel Functions There are four display windows on the control panel to provide feedback information. TIME WINDOW TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) INTER V AL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds SPEED WIN[...]

Pr ogr am and Oper a tion QUICK ST ART / MANUAL MODE 1. Plug into a surge protector outlet. Attach the Red Safety Key on to the treadmill console. 2. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 3. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be ente[...]

Pr ogr am and Oper a tion PROGRAM MODE Plug treadmill into a surge protector outlet. Attach the Safety Key on to the treadmill console. 1. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 2. Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME win- dow will flash. 3. There[...]

Pr ogr am Pr ofiles 16 The Fat Burn Pr ogram is designed to vary the treadmill elevation, while maintaining a constant walking belt speed. The Cardio Pr ogram is designed to vary the treadmill Speed, while maintaining a con- stant Elevation. The W arm Up Pr ogram is designed to gradually increase the treadmill Speed and Elevation in the first segme[...]

Belt Adjustment W ARNING! Do not over -tighten rollers! This will cause prema- ture r oller bearing failure! Belt adjustment and tension performs two functions: adjustment for tension and centering. Y our new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left or[...]

Change Miles per hour to Kilometer s per hour Y our treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). T o change the display to read in kilo- meters, follow the steps described here: 1) T urn power OFF on the console[...]

Maintenance Instr uctions W ARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector . CLEANING Routine cleaning of your HT502t Fitness treadmill will extend the life of your treadmill. W ARNING! T o pre- vent electrical shock, be sure the power to the treadmill is OFF and the unit unplugged[...]

T roubleshooting Guide T readmill will not start . 1. Is the Safety Key inserted into the treadmill Console? 2. Make sure the power cord is plugged into a surge protector , the sur ge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on page 12). 3. Check the circuit break[...]

Er r or Messages T readmill Err or Messages . Y our treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. The following error codes will be displayed in the console display windows. Safety Interlock Err or Messages SI 1 - Safety key missing, replace and try again. SI 2 - Over voltage prot[...]

Calibr a tion Sequence Do not attempt to calibrate the treadmill unless an Err or Code is present. See Err or Messages (page 21). Our treadmill is equipped with a software package that will perform a calibration sequence unique to your specific model number . Please perform the following steps to calibrate the HEAL TH TRAINER 502t TREADMILL. 1. Unp[...]

P ar ts List REF# KEYS PART# DESCRIPTION QTY. 1 423-00001 UPRIGHT CROSSBAR 1 2 423-00002 LEFT UPRIGHT 1 3 423-00003 RIGHT UPRIGHT 1 4 423-00004 BASE TUBE 1 5 423-00005 DECK FRAME 1 6 423-00006 MOTOR FRAME 1 7 404-00001 WALK BELT 430*2700*1.6 1 8 403-00001 WALK BOARD 1162*610*18 1 9 404-00002 POLY V-BELT 200J8(508J8) 1 10 406-00020 MOTOR COVER 720*3[...]

P ar ts List REF# KEYS PART# DESCRIPTION QTY. 51 402-00012 ALLEN BOLT M8*40 1 52 402-00013 ALLEN BOLT M8*40 2 53 402-00014 SCREW M6*25 8 54 402-00015 PHILIP SCREW ST4.2*16 10 55 402-00016 PHILIP SCREW ST4.2*13 7 56 402-00017 PHILIP SCREW M4*8 4 57 402-00018 PHILIP SCREW M6*12 4 58 402-00019 PHILIP SCREW ST4.2*13 6 59 402-00020 HEXAGRAM NUT M3 2 60 [...]

P ar ts List REF# KEYS PART# DESCRIPTION QTY. 74z 414-00002 SAFETY KEY DECAL 1 75 407-00001 MOTOR CONTROLLER 110V 1 76 424-00001 MOTOR 110V 1.5 1 76a 412-00002 MOTOR 1 76b 411-00003 FLYWHEEL 1 76c 406-00019 FAN 1 76d 402-00043 SCREW 1 76e 402-00044 SCREW 1 76f 402-00045 WASHER 1 77 412-00003 ACTUATOR 110V 1/15 1 78 413-00004 POWER CORD 1 79 408-000[...]

Exploded V iew 26[...]

Exploded V iew 27 CONSOLE ASSEMBL Y[...]

W ar r anty Inf or ma tion HT502t T readmill designed and distributed by KEYS FITNESS PRODUCTS, LP – LIMITED W ARRANTY PLEASE CONSUL T YOUR PHYSICIAN BEFORE USING THIS PRODUCT . This Limited W arranty applies in the United S tates and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the kEYS brand nam[...]

Customer Ser vice (888) 340-0482 K eys Fitness Pr oducts 4009 Distribution Drive Suite 250 Garland, TX 75041 www .keysfitness.com[...]