KingCraft PCSD180T manuale d’uso

CIRCULAR SAW INSTRUCTION MANUAL Item#3729 MODEL NO: PCSD180T PLEASE READ THESE INSTRUCTIONS CAREFULL Y TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS T OOL[...]

FUNCTIONAL DESCRIPTION Figure-1 1 FUNCTIONAL DESCRIPTION Figure 2 CLOCKWISE TO LOOSEN COUNTER CLOCKWISE TO TIGHTEN SWING NUT CUTTING DEPTH Figure-3 2[...]

FUNCTIONAL DESCRIPTION F i g u r e - 4 Figure-5 3 LIST OF MAIN P AR TS 1) B a t t e r y p a c k 6 ) N u t 2) U p p e r g u a r d 7 ) S a w b l a d e 3) B a s e 8 ) S w i t c h l o c k 4) F l a n g e 5) Lower guard Figure 6 9) ON/OFF switch CLAMP NUT TECHNICAL SPECIFICA TIONS : Description PCSD180T Rating V oltage 18V olts Nominal power 200W No-load[...]

2 3 4 5 F i g u r e - 7 Figure-8 GENERAL SAFETY RULES W ARNING! Read and und erstand all instructions. Fail ure to follow all instructions listed below may result in electric shock, fire or serious personal injury . SA VE ALL INSTRUCTIONS! WORK AREA 1. Keep your work area clea n and well or ganized. Cluttered benches and dar k areas invite accident[...]

situations. 6. Use safety equipment. Always wear eye protection. Dust mask, non-ski d safety shoes, hard hat, or hearing protect ion must be used for appropriate conditions. TOOL USE AND CA RE 1. Use clamps or other prac tical way to secure and support the workpiece to a stable platform . Holding the work by hand or against your body is unstable an[...]

guard is covering th e blade before placin g the saw down o n bench or floor . Be aware of the time it takes for the blade to s top after switch is releas ed. 7. NEVER hold piec e being cut in your hand or across the legs. It is importan t to support the w ork properly to m inimize body ex posure, blade binding, or loss of control. 8. Always use bl[...]

on a soft surface that m ight block the ventilat ion slots and result in excessive internal heat. Plac e the charger in a position away from any heat source. 11. Do not operate char ger if it has received a sharp blow , been dropped, or otherwise damaged in any way . T ake charger to an authorized service center . 12. Do not disassemble char ger, t[...]

use the correction screw . Adjusting the Cutting depth (See Fig.3&4) For the cleanest possible c ut, set the cutting depth whenever possi ble 5 mm deeper than the thickness of the m aterial. Slacken the swing nut for adjusting depth of cut, set the cut ting depth, and tighten the swing nu t again. Adjusting the cutting angle Slacken the swing n[...]

2) Insert the battery pac k into the ch arger , as shown in Fig 7, making sure the pack is fully sea ted in the char ger . The red light indicator wi ll illuminate showing that the battery is b eing char ged. 3) When char ging is well done green li ght will illuminate. The minimum charge tim e is normally 1hour after w hich the battery should b e r[...]

before installing or removing blade. 1. T o remove the bla de (Fig.8, press th e shaft l ock so that the blade cannot revolve and use the he x wrench to loosen th e bolt clock-wise. Then remove the bolt, outer flange and blade. 2. T o install th e blade, follow th e removal proced ure in reverse. BE SURE TO TIGHTEN THE BOL T SECUREL Y 3. Hold the w[...]

ridge.  T o avoid a tearing out of th e cutting edges w hen working sensitive area (if the surface is very smooth crepe tape also e nables easy drawing of line), fixing a thin bo ard of wood to the work piece and sawing through both will also avoid tearing out effectively . ADJUSTING FOR ACCURACY OF 90º CUT (VER TICAL) This adjustment has be en[...]

Both brushes should be re placed at the sam e time. Use only ide ntical carbon brushes. Use a screwdriver to rem ove the brush holder caps. T ake out the worn carbon brushes, insert the new ones and secure t he brush holder caps. TIPS FOR MAINT AINING MA XIMUM BA TTER Y LIFE 1. Charge t he battery pack befo re battery is completely discharg ed. Alw[...]