Lantronix UDS10 manuale d’uso

Part Number 900-360 Revision A June 2004 UDS10 UDS100 User Guide[...]

2 Copyright & Trademark © 2004, Lantronix. All rights reserved. No par t of the contents of this book may b e transmitted or reproduced in any form or by any means without the written permissi on of Lantronix. Printed in the United States of America. Ethernet is a trademark of XEROX Corporati on. UNIX is a registered trademark of The Open Grou[...]

3 Disclaimer & Revisions Operation of this equipment in a residentia l area is likely to cause int erference, in which case the user, at his or her own expense, will be required to take whatever measures may be required to correct the interference. Note: This product has be en designed to comply with the lim its for a Class A digital device pur[...]

4 Contents Contacts 2 1: Using This Guide 8 Purpose and Audience________________________________________________ 8 Chapter Summary ___________________________________________________ 8 Additional Documentation _____________________________________________ 9 2: Introduction 10 Applications _______________________________________________________ 10 A[...]

UDS10/UDS100 User Guide 5 Remote IP Address ______________________________________________ 32 Remote Port ___________________________________________________ 32 Disconnect Mode _______________________________________________ 33 Flush Mode ____________________________________________________ 33 Pack Control __________________________________________[...]

UDS10/UDS100 User Guide 6 Network Port ___________________________________________________ 53 Ethernet Connector Pinouts _______________________________________ 54 10: Technical Specifications 55 UDS10 Technical Specifications _______________________________________ 55 UDS100 Technical Specifications ______________________________________ 56 A: Alt[...]

UDS10/UDS100 User Guide 7 Figure 9-4. Null-Modem Cable (L antronix Part No. 500-163) ___________________ 53 Figure 9-5. Network Interface ___________________________________________ 53 Figure 9-6. RJ45 Ethernet Connector _____________________________________ 54 Tables Table 5-1. Standard IP Network Netmasks _________________________________ 25 Tabl[...]

8 1 1 : : U U s s i i n n g g T T h h i i s s G G u u i i d d e e Purpose and Audience This guide provides the informatio n nee ded to configure, use, and update the UDS device server. It is for system admini strat ors and those respon sible for installing and maintaining the UDS. Chapter Summary The remaining chapters in this guide incl ude: 2: In[...]

UDS10/UDS100 User Guide Using This Guide 9 Additional Documentation The following information is available on the product CD or the Lantronix We b site:www.lantronix.com DeviceInstaller User Guide Pr ovides instructions for usi ng the Windows-based utility to configure the UDS and other Lant ronix device servers. (CD and web site) “Live” Tutori[...]

10 2 2 : : I I n n t t r r o o d d u u c c t t i i o o n n The UDS10 and UDS100 are single-port device serve rs that provide a quick, simple, and cost-effective way to bring the advan tages of data accessibility and remote management to devices not currently conne cted to a network. The main difference between the two m odels is that the UDS100 pro[...]

UDS10/UDS100 User Guide Introduction 11 Figure 2-1. Application Examples Note: For step-by -step instructions on config uring the UDS for serial tunneling or for use with the Com Port Redirecto r, access the UDS Configuration Tutorials usi ng Web Manager. (See Accessi ng Web Manager on page 18.)[...]

Introduction UDS10/UDS100 User Guide 12 Protocol Support The UDS uses the Internet Protocol (IP) for network communications and the Transmission Control Protocol (TCP ) to assu re that no data is lost or duplicated and everything sent to the connection arrives correctly at the target. Supported protocols include:  ARP, UDP, TCP, ICMP, Telnet, TF[...]

UDS10/UDS100 User Guide Introduction 13 Product Information Label The product information label on the under side of the unit contains the following information about your specific unit:  Bar code  Serial number  Product ID (name)  Product description  Hardware address (also re ferred to as the Ethernet or MAC address) The first thre[...]

14 3 3 : : G G e e t t t t i i n n g g S S t t a a r r t t e e d d This chapter describe s how to get your UDS up and running in the shortest possible time. Installing the UDS Figure 3-1. UDS Connected to Serial Device and Netwo rk To install the unit, complete the following steps in ord er. Refer to the numbers in the figure above. 1. Connect a se[...]

UDS10/UDS100 User Guide Getting Started 15 Required Information Before configuring the UDS, have t he following information available: Hardware Address Take note of the unit’s hardware addre ss (also known as the Ethernet or MAC address). It is on the product label, in the format: 00-20-4a-XX-XX-XX, where the XXs are unique numbers a ssigned to t[...]

Getting Started UDS10/UDS100 User Guide 16 Assigning the IP Address and Related Network Settings This section describes two ways to as sign the IP address and related network settings quick ly.  DeviceInstaller  Serial Port Login DeviceInstaller Note: The DeviceInstaller User Guide and the Devi ce Installer online help provide more detailed i[...]

UDS10/UDS100 User Guide Getting Started 17 Adding the Unit to the Manage List Now add the unit to the list of similar Lant ronix devices on the network so that you can manage and configure it. To perform this step, cl ick the Search icon. DeviceInstaller locates the unit and adds it to the list. Now you can manag e (configure) the unit so that it w[...]

18 4 4 : : C C o o n n f f i i g g u u r r i i n n g g t t h h e e U U D D S S U U s s i i n n g g W W e e b b M M a a n n a a g g e e r r You must configure the UDS so that it can communicate on a netwo rk with your serial device. For example, you must set the way the unit responds to serial an d network traffic, handles serial packets, and sta rt[...]

UDS10/UDS100 User Guide Configuring the UDS Using Web Man ager 19 Figure 4-2. UDS Configuration G uidelines Page  UDS settings opens a co nfiguration window to confi gure the UDS10/UDS100, as show n in Figure 4-3.  Serial cabling lets you view pinouts for the UDS serial port.  View UDS Configuration Tutorials provides step-by-step instruct[...]

Configuring the UDS Using Web Man ager UDS10/UDS100 User Guide 20 Using Web Manager 1. To configure the unit, select UDS Settings on the UDS Configuration Guid elines Page. The Web Manager page display s. Figure 4-3. Lantronix Web Manager 2. Use the menu (pushbuttons) to navigat e to sub pages where you can co nfigure server settings. Note: For det[...]

UDS10/UDS100 User Guide Configuring the UDS Using Web Man ager 21 Figure 4-4. Server Properties C onfiguration on the Web Browser 3. In the Telnet Password field, enter a password to prevent unautho rized access to the Setup Mode using a Telnet connection to port 9999. The password i s limited to 4 characters. (An enhanced p assword setting of 16 c[...]

22 5 5 : : C C o o n n f f i i g g u u r r i i n n g g t t h h e e U U D D S S U U s s i i n n g g T T e e l l n n e e t t o o r r t t h h e e S S e e r r i i a a l l P P o o r r t t You must configure the UDS so that it can communicate on a netwo rk with your serial device. For example, you must set the way the unit will respond to serial and n et[...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 23 Figure 5-2. Setup Mode 3. Select an option on the Change Setup menu by entering the numb er of the option in the Your choice ? prompt and pressin g Enter. 4. To enter a value for a parameter, type the value and press Enter . To confirm a current value, just press Enter .[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 24 2. Type three lowercase x characters ( xx x ) within one second after powering up to start the configuration mode. Note: The easiest way to enter Setup Mode is to ho ld down the x key o n your keyboard while p owe ring up the unit. The configuration settings displ ay, f[...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 25 Note: Class A: 24 bits; Class B: 16 bits; Class C: 8 bits. The unit prompts for the number of host bi ts to enter, then cal culates the netmask, which displays in standard decim al-dot notation when the saved parameters di splay (for example, 255.255.255.0). Table 5-1. S[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 26 If you give the unit an IP of 0.0.0.0, you then have the option to assign an 8-character DHCP name. Figure 5-4. Server Configur ation Option Change DHCP device name (LTRX) ? (N) Y Enter new DHCP device name : LTRXYES Channel 1 Configuration (Serial Port Settings) Note: [...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 27 The following table displays available I/F Mode optio ns: Table 5-3. Interface Mode Options I/F Mode Option Bit 7 6543210 RS-232C 0 0 RS-422/485 0 1 RS-485 2-wire 1 1 7 Bit 1 0 8 Bit 1 1 No Parity 0 0 Even Parity 1 1 Odd Parity 0 1 1 Stop bit 0 1 2 Stop bit 1 1 The follo[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 28 Table 4-5. Reserved Port Nu mb ers Port Numbers Reserved for 1 – 1024 Reserved (well kno wn ports) 9999 Telnet setup 30718 Reserved (77FEh) Warning: We recommend that you not use the reserved port numbers for this setting as incorrect operation may result. Use port 0 [...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 29 Manual Connection The UDS attempts to connect when directed by a co mmand string received from the serial port. The first charact er of the command string must be a C (ASCII 0x43), and the last character must be either a carriage retu rn (ASCII 0x0D) or a line feed (0x0A[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 30 Figure 5-6. Hostlist Option To use the hostlist option, follow these steps: 1. To enable the hostlist, enter a Connect Mode of 0x20 ( 2X ). The menu shows you a list of current entries already defined in the produ ct. 2. To delete, modify, or add an entry, select Yes . [...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 31 accumulating phone charg es for each connection. Modem Mo de allows you to replace modems with UDS units, and to use an Ethernet connection instea d of a phone call. By not having to change communication s applications, you avoid potentially expensive phone calls. To sel[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 32 Table 5-8. Modem Mode Co mmands Modem Mode Command Function ATDTx.x.x. x,pppp or ATDTx.x.x. x/pppp Makes a connection to an IP address (x.x.x. x) and a remote port number (pppp). ATDT x.x. x.x Makes a con nection to an IP address (x.x.x. x) and the remote port number de[...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 33 Disconnect Mode This option determines the conditio ns under which the unit cau ses a network connection to terminate. In DisConnMod e, DTR drop either drops the conne ction or is ignored. Note : To look up hex values, see B: Binary to Hexadecim al . Table 5-9. Disc onne[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 34 Pack Control Two firmware-sel ectable packing algorit hms define how and wh en the unit sends packets to the network. The standard al gorithm is optimized for ap plications in which the unit is used in a local environment, allowing for very small delays for si ngle char[...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 35 Disconnect Time (Inactivity Timeout) Use Disconnect Time to set an inactivity timeout. The unit drops the conne ction if there is no activity on the serial line before the set time expires. Enter time in the following format: mm:ss, where m is the number of minutes and s[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 36 TCP Keepalive time in s This option defines how many se conds the unit waits durin g a silent connection before checking to see whether the currently connect ed net work device is still on the network. If the unit does not receive a re spon se, it drops that connection.[...]

UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port 37 SNMP Community Name This option changes the SNMP commu nity name on the unit. This allows for ease of management, and possibly some security. If someone tries to violate se curity but does not know what comm unity to connect to, that person is unable to obtain the SNMP c[...]

Configuring the UDS Using Telnet or th e Serial Port UDS10/UDS100 User Guide 38 Factory Default Settings Select 7 to reset the unit’s serial po rt to the factory default settings. The server configurations (IP address information ) re main unchanged. The specific settings that this option changes are in the following list: Channel 1 Configuration[...]

39 6 6 : : U U p p d d a a t t i i n n g g F F i i r r m m w w a a r r e e This chapter explains how to obtain and update the unit’s firmware. Obtaining Firmware Obtain the most up-to-date firmware an d release notes for the unit from the Lantronix Web site (http://www.lantronix .com/) or by using anony mous FTP (ftp://ftp.lantronix.com/). Reload[...]

Updating Firm ware UDS10/UDS100 User Guide 40 6. Select Do not copy or replace any files and click Next . Note: This option upgrades the firmware file (.ROM file) only, not the Web Manager files (.COB). 7. Click Next again. The status of the upgra de shows in the window. 8. After the upgrade completes, click Close . Using TFTP If you are running Wi[...]

UDS10/UDS100 User Guide Updating Firm ware 41 Figure 6-1. TFTP Dialog Box The unit performs a power reset after the firmwa re has been loaded and sto red. Using Another Unit To distribute firmware to another unit over the network: 1. Enter the host unit's Monitor Mode (see 7: Usin g Monitor Mode ) . 2. Send the firmware to the receiving unit u[...]

Updating Firm ware UDS10/UDS100 User Guide 42 2. Download the firmware to the unit using the DL command. 3. Select Send Text File and select the LTX*.HEX file for the UDS10 or DLX*.HEX file for the UDS100 to be downloaded. The downloa ded file must be the .HEX (ASCII) version. 4. After receiving the final record, the unit checks the integrity of th[...]

43 7 7 : : U U s s i i n n g g M M o o n n i i t t o o r r M M o o d d e e Monitor Mode is a command line interfa ce used for diagnostic pu rposes. There are two ways to enter Monitor Mode: locally using the seri al port or remotely using the network. Entering Monitor Mode Using the Serial Port To enter Monitor Mode locally, follow the same prin ci[...]

Using Monitor Mode UDS10/UDS100 User Guide 44 Using Monitor Mode Commands The following commands a re available in Monitor Mode. Many commands hav e an IP address as an optional parameter (x.x.x.x). If the IP address is given, the command is applied to another unit with that IP address. If no IP address is given, the command is executed locally. No[...]

45 8 8 : : T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g a a n n d d C C o o n n t t a a c c t t I I n n f f o o r r m m a a t t i i o o n n This chapter discusses ho w you can diagnose and fix erro rs quickly without having to contact a dealer or Lantronix. It helps to connect a terminal to the serial port whil e diagnosing an error [...]

Troubleshooting and Contact Informa t ion UDS1 0/UDS100 User Guide 46 Table 8-1. UDS10/UDS100 L E Ds Serial LEDs Meaning 10 Mbps link/activity steady green Valid 10 Mbps network connection 10 Mbps link/activity blinking Network packets transmitting and receiving 100 Mbps link/activity steady gree n Valid 100 Mbps net work connection 100Mbps link/ac[...]

UDS10/UDS100 User Guide Troubleshooting and Contact Informa t ion 47 Problem/Message Reason Solution You may have entered the har dware address incorrectly with the ARP command. Confirm that the hardware address that you entered with the ARP command is correct. The hardware address may only include numbers 0-9 and letters A-F. In Windows and usuall[...]

Troubleshooting and Contact Informa t ion UDS1 0/UDS100 User Guide 48 Problem/Message Reason Solution The UDS is not communicating with the serial device attached to the UDS. The most likely reason is the wron g serial cable or serial settings were chosen. Make sure that you are using the correct serial cable. The UDS serial port is just like a mod[...]

UDS10/UDS100 User Guide Troubleshooting and Contact Informa t ion 49 Problem/Message Reason Solution You are using the correct serial cable, and the UDS is set up correctly, but you are not communicating with your device attached to the UDS across the network. If you are sure that the serial cable is correct, then you may not be connecting to the c[...]

Troubleshooting and Contact Informa t ion UDS1 0/UDS100 User Guide 50 When you report a problem, please prov ide the following information:  Your name, and your company name, address, an d phone number  Lantronix UDS model number  Lantronix UDS serial number  Software version (on the first screen shown when you Telnet to port 9999)  [...]

51 9 9 : : C C o o n n n n e e c c t t i i o o n n s s a a n n d d P P i i n n o o u u t t s s Serial Port The UDS has a female DCE DB25 serial port that supports RS-232 and RS-485/422 serial standards (software sele ctable) up to 115 Kbps. Figure 9-1. Serial Interface Serial Connector Pinouts The unit’s female DB25 connector prov ides an RS-232C[...]

Connections and Pinouts UDS10/UDS100 User Guide 52 Figure 9-2. DB25 Female DC E In terface RS232 Figure 9-3. DB25 Female DC E In terface RS485/422[...]

UDS10/UDS100 User Guide Connectons and Pinouts 53 Null-Modem Cable When attaching the DB9 of the UDS to the DB9 com port on a PC, use a null-modem cable (Lantronix Part No. 500-163 ). The figure below shows the pin outs for a DB9 to DB9 null-modem cable. To configure the UDS using th e DB9 serial port, you only need to pinout the TXD, RXD, and GND [...]

Connections and Pinouts UDS10/UDS100 User Guide 54 Ethernet Connector Pinouts The UDS10 supports 10 Mbps half-du plex Ethernet through an RJ45 conne ctor. The UDS100 supports 100 Mbps half or full dupl ex Ethernet through an RJ45 connector. Figure 9-6. RJ45 Ethernet Connector[...]

55 1 1 0 0 : : T T e e c c h h n n i i c c a a l l S S p p e e c c i i f f i i c c a a t t i i o o n n s s UDS10 Technical Specifications CPU, Memory x86 CPU, 25MHz clock, 128kByte RAM Serial Interface Female DB25 connector (DCE pinout ) Speed software selectable (300 to 11 5 kBaud) Software selectable RS-232C or RS-422/485 Network Interface 10 Mbp[...]

Technical Specifications UDS10/UDS100 User Guide 56 UDS100 Technical Specifications CPU, Memory Lantronix DSTni-LX 186 CPU, 48 MHz 1 MByte FLASH ROM 256 Kbytes zero wait state RAM Serial Interface Female DB25 connecto r (DCE pinout) Speed software selectable (300 to 11 5 kBaud) Software selectable RS-232C or RS-422/485 Network Interface 10/100 RJ45[...]

57 A A : : A A l l t t e e r r n n a a t t i i v v e e W W a a y y s s t t o o A A s s s s i i g g n n a a n n I I P P A A d d d d r r e e s s s s Earlier chapters describe how to a ssign a static IP address usin g DeviceInstaller, Web Manager, and Setup Mode (th rough a Telnet or serial co nnection). This section covers other methods for assi gnin[...]

Alternative Ways to Ass i gn an IP Address UDS10/UDS100 User Guide 58 BOOTP Similar to DHCP, but for smaller networks. Automatically assign s the IP address for a specific duration of time. ARP and Telnet If the unit has no IP address, you can use Addres s Resolution Protocol (ARP) method from UNIX and Windows-ba sed systems to assi gn a temporary [...]

59 B B : : B B i i n n a a r r y y t t o o H H e e x x a a d d e e c c i i m m a a l l C C o o n n v v e e r r s s i i o o n n s s Many of the unit’s configuration procedures require yo u to assemble a series of options (represented as bits) into a comp lete comma nd (represented as a byte). The resulting binary value must be converted to a hexad[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 60 Scientific Calculator Another simple way to convert bina ry to hex adecimals is to use a scientific calcula tor, such as the one available on Win dow s’ operating systems. For example: 1. On the Windows’ Start menu, click Programs Æ Accessories Æ Calculator . 2. On the View menu, se[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 61 Connect Mode Options Note: Character response codes are C=conn, D=di sconn, N=unreachable Connect Mode Options Accept Incoming Connections Serial Response Upon Connection Active Connection Startup Hostlist Hex Never Non e (quiet) No active startup N/A Never Non e (quiet) Any character 1 N[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 62 Connect Mode Options Accept Incoming Connections Serial Response Upon Connection Active Connection Startup Hostlist Hex Unconditionally None (qui et) Autostart C5 Unconditionally Non e (quiet) UDP CC Unconditionally Character No active startup D0 Unconditionally Char acter An y character [...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 63 Connect Mode Options Accept Incoming Connections Serial Response Upon Connection Active Connection Startup Hostlist Hex Unconditionally None (quiet) No active start up Hostlist N/A Unconditionally None (quiet) An y character Hostlist E1 Unconditionally None (quiet) Active DT R Hostlist E2[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 64 Disconnect Mode Options Disconnect Mode Option s Disconnect with DTR Drop Telnet Mode and Terminal Type Setup Channel (port) Password Hard Disconnect State LED Off with Connection Disconnect wi t h E O T (^D) Hex Enable 0 Enable Enab le 10 Enable Enable 20 Enable Enab le Enable 30 Enab le[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 65 Disconnect Mode Option s Disconnect with DTR Drop Telnet Mode and Terminal Type Setup Channel (port) Password Hard Disconnect State LED Off with Connection Disconnect wi t h E O T (^D) Hex Enab le Enable Disable Enab le 78 Enable Disable 88 Enable Enable Disable 98 Enable Disable Enable A[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 66 Flush Mode Options Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex None 0 Active connection 10 Passive connection 20 Active connection Passive connection 30 Disconnect 40 Active connection Disconnect[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 67 Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex Active connection Passive connection Active connection Enab le B1 Disconnect Active connection Enable C1 Active connection Disconnect Active connection[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 68 Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex Active connection Disconnect Active connection Passive connection 53 Passive connection Disconnect Active connection Passive connection 63 Active conne[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 69 Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex Passive connection Disconnect Disconnect Enable E4 Active connection Passive connection Disconnect Disconnect Enable F4 Active connection Disconnect 5 [...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 70 Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex Disconnect Passive connection Disconnect 46 Active connection Disconnect Passive connection Disconnect 56 Passive connection Disconnect Passive connect[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 71 Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Hex Active connection Passive connection Disconnect Active connection Passive connection Disconnect 77 Active connection Passive connection Disconnect Enab[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 72 Interface Mode Options Interface Mode Options Interface Bits Parity Stop Bits Hex RS-232C 7 No 1 48 RS-232C 7 No 2 C8 RS-232C 7 Even 1 78 RS-232C 7 Even 2 F8 RS-232C 7 Odd 1 58 RS-232C 7 Odd 2 D8 RS-232C 8 No 1 4C RS-232C 8 No 2 CC RS-232C 8 Even 1 7C RS-232C 8 Even 2 FC RS-232C 8 Odd 1 5[...]

UDS10/UDS100 User Guide Binary to Hexadecimal Conversions 73 Pack Control Options Pack Control Options Sendcharacter Defined by a: Trailing Characters Idle Time Force Transmit: Send Immediately after Sendcharacter Hex 1-Byte Sequence No 12ms 0 1-Byte Sequence No 52ms 1 1-Byte Sequence No 250ms 2 1-Byte Sequence No 5sec 3 1-Byte Sequence 1 12ms 4 1-[...]

Binary to Hexadecimal Conversions UDS10/UDS100 User Guide 74 Pack Control Options Sendcharacter Defined by a: Trailing Characters Idle Time Force Transmit: Send Immediately after Sendcharacter Hex 2-Byte Sequence No 5sec Yes 33 2-Byte Sequence 1 12ms Yes 34 2-Byte Sequence 1 52ms Yes 35 2-Byte Sequence 1 250ms Yes 36 2-Byte Sequence 1 5sec Yes 37 2[...]

75 Declaration of Conformity (according to ISO/IEC Guide 22 and EN 45014) Manufacturer’s Name & Address : Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA Declares that the follo wing product: Product Name Model: Device Servers UDS10 and UDS 100 Conforms to the follo wing standards or other normativ e documents: Safety: EN60950:19 92+A1[...]

76 Warranty Lantronix warrants each Lantronix product to be free from defe cts in material and workmanship for a period of TWO YEARS after the date of shipm ent. During this period, if a customer is unable to resolv e a product problem and La ntronix Technical Support determines the product is defectiv e, a Return Material Authorization (RMA) will [...]

77 Index Application examples, 10 ARP and Telnet, 58 ARPCache timeout, 36 AutoIP, 15, 57 Baudrate, 26 Binary to hexadecimal conversions, 59 BOOTP, 15, 58 Buffer flushing, 33 Cable, 53 Com Port Redirector tutorial, 19 Compliance, 75 Connect Mo de, 28 Connecto rs, 51 DB9 to DB9 null-modem cable, 53 Defaults List, 38 Resetting, 38 DeviceInstaller Assi[...]

Index UDS10/UDS100 User Guide 78 Login, 17 Settings, 26 Serial tunneling Example, 10 Tutorial, 19 Server properties, 20 Setup Mode Accessing by Serial Port, 23 Accessing using Telnet, 22 Disabling Telnet access, 37 using, 23 SNMP Changing community name, 37 Disabling, 36 Subnet mask Assigning on Web Manage r, 20 TCP Keepalive time, 36 Technical spe[...]