LG Electronics LMV1630WW manuale d’uso

W ebsite: http://us.lgservice.com MICR O W A VE O VEN INST ALLA TION INSTR UCTIONS PLEASE READ AND SA VE THESE INST ALLA TION INSTRUCTIONS. P/NO.: 3828W5U 0 529[...]

– 2 – Y our Safety Fir st BEFORE Y OU ST ART • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The model number label is located on the oven front. See Figure 1. The mounting plate is located on back side of microwave oven. See Figure 2. NOTE: Vent grille appearance varies by model. BE [...]

– 3 – Y our Safety Fir st • THIS APPLIANCE MUST BE GROUNDED! – If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. • Place the plug into a properly installed and gr[...]

– 4 – Y our Safety Fir st • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. – ATTACH (See note on page 5) the two lag screws supporting the oven[...]

– 5 – P ar ts, T ools, Materials THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector (for roof venting or wall venting installation) Not Actual Size (2 pieces must be assembled as shown) Not used if venting into kitchen. One power cord clamp [...]

– 6 – P ar ts, T ools, Materials Clear Tape (for taping the templates to the wall) Phillips Screwdriver (for the screws) Pencil Flat Blade Screwdriver (for the toggle bolts) Plumb Line Measuring Tape (metal preferred) Duct Tape Small Side Cutters or Tin Snips Caulking Gun and Caulk Stud Finder or Thin Nail Saber Saw (for cutting vent holes for [...]

– 7 – STEP 1: Prepare The Electrical Connection Improper gr ounding could result in electric shoc k or other personal injury . 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. NOTE: The outlet should be on a circuit dedicated to the microwave oven (120V, 60 Hz., AC only) with a 15 or 20A [...]

– 8 – STEP 2: Prepare The V enting System THIS O VEN MUST BE PR OPERL Y VENTED! W ARNING NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 9. You may vent your oven in one of three ways. However, do NOT vent into a wall cavity, an attic, or [...]

– 9 – STEP 2: Prepare The V enting System Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper ’ s sticking. Duct Length The total length of the duct system, including str[...]

– 1 0 – STEP 3: Prepare The V enting Blo wer Your microwave oven is shipped with the blower assembled for roo m - vent ed . You need to adjust the blower if you want wall-vent ed or roo f -vented installation. • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock. REMO VE THE MOU[...]

– 1 1 – STEP 3: Prepare The V enting Blower W ALL-VENTED INST ALLA TION: 1. Remove one blower unit mounting screw and one or several blower plate mounting screw(s). Remove the blower plate from cabinet. See Figure 1 3 . 2. Carefully lift the blower unit out of the microwave oven. 3. Use side cutters or tin snips to cut and remove knockouts B fr[...]

– 1 2 – STEP 3: Prepare The V enting Blo wer ROOF-VEN T ED INSTALLATION: 1. Remove one blower unit mounting screw and one or several blower plate mounting screw(s). R e m o v e t he b l o w e r p l a t e f r o m c a b i n e t . S e e Figure 19. 2. Carefully lift the blower unit out of the microwave oven. 3. Rotate blower unit 90 so the exhaust [...]

– 1 3 – STEP 4: Prepare The W all & Upper Cabinet T o av oid per sonal injury or property damage , do not attempt to install this micro wave oven if y ou cannot find a wall stud. Consult a carpenter or contractor . W ARNING Upper Cabinet Template Mounting Plate (1-piece Mounting Plate) (3-piece Mounting Plate) Upper Cabinet Template Mountin[...]

– 1 4 – STEP 4: Prepare The W all & Upper Cabinet Drill The Holes In The W all And Upper Cabinet. 1. Drill holes on the circles. If there is a stud, drill a 3/16 " hole for lag screws. If there is no stud, drill a 3/4 " hole for toggle bolts. Make sure to use at least 2 lag screws in a stud, and 4 toggle screws in the drywall or t[...]

– 1 5 – STEP 5: Install The Mounting Plate Center Line A C B Draw Center Line Draw Lines on Studs For Wall- Vented Only Minimum 66 " From the Floor Support Tab Support Tab E Mounting Plate D 3/16 Hole on Studs 5/8 Hole on Drywall Only 3/16 Hole on Studs 5/8 Hole on Drywall Only Center Line Draw Center Line Draw Lines on Studs For Wall- Ven[...]

– 1 6 – STEP 5: Install The Mounting Plate Slide exhaust adaptor into guides on rear panel. Exhaust Adaptor Damper (hinge side up) Locking T abs Guides Mounting Plate Back Plate (1-piece Mounting Plate) (3-piece Mounting Plate) For W all-V ented Make the box cutout for the rear wall duct. – 1-piece mounting plate: Using a pencil, put dots thr[...]

– 1 7 – STEP 6: Attach The Oven T o The W all 1. Carefully lift microwave oven and hang it on support tabs (See Figure 27) at the bottom of the mounting plate.Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. See Figure 31. 2. Rotate the microwave oven upward so the t[...]

– 1 8 – STEP 6: Attach The Oven T o The W all Damper Power supply Cord Clamp 5. Roof venting installation: See Figure 33. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See Prepare The Venting System STEP 2. Use caulking gun to seal the exterior roof o[...]

Printed in China[...]