LG Electronics W2220P manuale d’uso

M ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service. W2220P User's Guide[...]

1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the powe[...]

2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventila[...]

Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. [...]

4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . User's Guide/Cards Power Cord (Depending on the country) 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) DV[...]

5 Connecting the Display Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices are turned off. Connecting the stand base 1 . Place the monitor with its front facing downward on a cushion or soft cloth. 3 . Once assembled take the monitor up carefully and face the front side. WARNING T[...]

6 Connecting the Display IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Positioning your display After installation, adjust the angle as shown [...]

7 Connecting the Display Swivel Range : 355 ˚ 355 Height Range : maximum 4.33 inches (110.0 mm) * Please be sure to remove the Locking pin to adjust the height. 110.0 mm ERGONOMIC I t is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. WARNING Yo[...]

8 Connecting the Display -The pivot function allows you to rotate the screen 90 degrees clockwise. 1 . Lift the monitor to its highest height to utilize the Pivot function. 2 . Landscape & Portrait : You can rotate the panel 9 0 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the scree[...]

Connecting the Display 9 A B Connect DVI-D Cable Connect D-SUB Cable Connect HDMI Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw of the signal cable. Connecting with the PC/ A V [...]

10 Connecting the Display NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry [...]

11 Control Panel Functions Front Panel Controls MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You[...]

12 Control Panel Functions Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). (Only for D-SUB input) This will automatically adjust your display image to the ideal settings for the curr[...]

13 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjus[...]

14 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. MOVIE TEXT PHOTO USER sRGB MODE BRIGHTNESS CONTRAST GAMMA BLACK LEVEL PICTURE Standard image settings. : D-SUB(Analog signal) input : DVI-D(Digital signal) input : HDMI input DSUB DVI HDMI Main menu Sub-[...]

15 On Screen Display(OSD) Selection and Adjustment NOTE The order of icons may differ depending on the model (14~21). LANGUAGE OSD POSITION (HORIZONTAL / VERTICAL) WHITE BALANCE OVERSCAN POWER INDICATOR 4:3 IN WIDE FACTORY RESET Additional settings SETUP HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS Adjusts the clarity and stability of the screen TRACK[...]

16 16 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the MODE button on the front of the monitor. Main menu Description Icons Menu Name Sub-menu Name MENU : Exit : Move SET : Select MOVIE It is a mode that the screen is adjusted to the best to view the videos. TEXT PHOTO USER sRGB * Outside the User mode, [...]

17 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub- menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Menu Name[...]

18 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE MENU : Exit : Decrease : Increase SET : Select another sub-menu BRIGHTNESS CONTRAST GAMMA BLACK LEVEL To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : 1.8 ~ 2.6 On the monitor, high gamma values display [...]

19 On Screen Display(OSD) Selection and Adjustment COLOR TEMP PRESET Select either PRESET or USER to adjust the screen color. Select the preset color temperature. 5700K-6500K: Yellow screen color. 6500K-7500K: Red screen color. 8500K-9300K: Blue screen color. COLOR Main menu Sub menu Description PRESET Mode USER Mode USER RED GREEN BLUE SIX COLOR H[...]

20 On Screen Display(OSD) Selection and Adjustment TRACKING Main menu Sub menu Description MENU : Exit : Decrease : Increase SET : Select another sub-menu CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows [...]

21 On Screen Display(OSD) Selection and Adjustment SETUP Main menu Sub menu Description To choose the language in which the control names are displayed. To adjust position of the OSD window on the screen. If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion. Using t[...]

22 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator red? ● Is the power indicator blinking? ● Do you see an [...]

23 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results a[...]

24 T roubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel -[...]

25 NOTE Information in this document is subject to change without notice. Specifications 22.0 inches (55.867 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 55.867 cm 0.282 x 0.282 mm (Pixel Pitch) Display Horizontal Freq. 30 - 83 kHz (Automatic) Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate Sync. Digital[...]

26 Specifications Preset Modes (Resolution) - D-sub(Analog) / DVI-D(Digital) INPUT Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode Indicator On Mode Sleep Mode Off Mode Red Red Blinking Off LED Color MODE Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 2 3 4 5 6 7 8 480P 576P 720P 720P 1[...]

27 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. Wall mount plate (Separate purchase) - Be sure to use screws and a wall mount that meet VESA standards. - Using screws longer than those recommended might damage the product. - Using screws that do not meet VESA standard[...]

Digitally yours[...]