LG 27EB22PY manuale d’uso

www .lg.com O WNER’S MANU AL IPS LED MONIT OR IPS LED MONIT OR MODEL 27 EB22PY P l ea s e re a d th i s ma n u a l ca r e fu l l y b e for e op e r a t i n g yo u r se t a n d re tain it f or futur e ref erenc e. ENGLISH[...]

1 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) DVI-D Signal Cable (This feat[...]

2 Connecting the Display Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices are turned off. Connecting the stand base 1 . Place the monitor with its front facing downward on a cushion or soft cloth. 2 . Assemble the Stand Base into the Stand Body. Be sure don't pull out the St[...]

3 Connecting the Display IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 3. Use a coin on the back of the stand base and turn the screw clockwis[...]

4 Connecting the Display Height Range : maximum 5.12 inches ( 13 0 .0 mm) * Please be sure to remove the Locking pin to adjust the height. 130.0m m Positioning your display After installation, adjust the angle as shown below . 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range Swivel Range : 355˚[...]

5 Connecting the Display ERGONOMIC I t is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. WARNING You do not need to replace the Locking pin after it is removed, to adjust its height. When adjusting the angle of the screen, do not put your finger[...]

6 Connecting the Display -The pivot function allows you to rotate the screen 90 degrees clockwise. 1 . Lift the monitor to its highest height to utilize the Pivot function. 2 . Landscape & Portrait : You can rotate the panel 9 0 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the scree[...]

7 Connecting the Display A B Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw of the signal cable. Connecting with [...]

8 Connecting the Display NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry scree[...]

Connecting the Display Connecting the USB(Universal Serial Bus) Cable 1 . You can use the USB port at the back of the monitor to connect peripherals (US B mouse, USB keyboard, etc.) to the monitor, not to the computer. 2 . The monitor’s USB terminal supports USB 2.0 and High Speed cables . Two USB Downstream ports Connect these ports to a mouse, [...]

Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MEN[...]

Control Panel Functions INPUT Button When two input signals are connected, you can select the input signal (D-SUB/DVI/DP) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub. (SOURCE Hot key) Exit the OSD(On Screen Display). EXIT Button AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display[...]

On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustme[...]

On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : D-SUB(Analog signal) input : DVI-D(Digital signal) input : DP(DisplayPort signal) input DSUB DVI-D To adjust the volume To customize the screen status for a user's operating environment To adjust the[...]

On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub- menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Menu Name Ic[...]

On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. Change the input image signal ratio to original. WIDE ORIGINAL Switch to full screen mode according to input image signal. * This function works only if input resolution is lower than monitor ratio (16:9). Exit : Exit , , : Move : [...]

On Screen Display(OSD) Selection and Adjustment Main menu Description To choose the language in which the control names are displayed. Press the , buttons to reset immediately. Restore all factory default settings except "LANGUAGE." To adjust the contrast of the screen. Exit : Exit , , : Move : Select another sub-menu You can set the offs[...]

On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Menu Name Ico[...]

On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Exit : Exit , : Move : Select another sub-menu Turn on the SUPER ENERGY SAVING fuction. When current setting value is ON,the SUPER SAVING color is green. Turn off the SUPER ENERGY SAVING function.Now the monitor is LED SAVING function. When current setting value is OFF,t[...]

On Screen Display(OSD) Selection and Adjustment SUPER SAVING LED SAVING 6 10 27 inch Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal. LED Saving means that how much power can be saved using WLED Panel i[...]

T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "OUT OF RANGE" message on the screen? ?[...]

T roubleshooting IMPORT ANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution . If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure [...]

Specifications 68.6 cm ( 27 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 68.6 c m 0.3114 x 0.3114 m m (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. Analog, Digital :56 Hz to 75 Hz (Automatic) DisplayPort:56 Hz to 61 Hz (Automatic) Input Form Separate Sync. Digital Sync Input [...]

Specifications Operating Conditions Temperature 10 ˚C to 35 ˚C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 ˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing Environment al Conditions Attached ( ), Detached ( O ) Stand Base Wall-outlet type Power cord NOTE Information in this document is subject to change without notice[...]

Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode 1 2 3 4 5 6 7 8 9 10 11 *12 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 31.468 31.469 37.500 37.879 46.875 48.363 60.023 67.500 63.981 7[...]

Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. 1 . After moving the product to face downward, make sure to place it on a soft 2 . Separate the head and the stand with the use of a screwdriver. cloth or a cushion to avoid surface damage. 25[...]

Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores. 3. Install [...]

M a k e s u r e to r e a d t h e Sa fe t y P r e c a u ti o ns befor e using the product . K e e p t h e O W N E R ’ S M A N UA L ( C D ) i n a n acces sible place f or furture ref erence. The m ode l and seri al n umb er of t he S ET is located o n the bac k or one s ide of th e SET . Rec ord it below should y ou ever need ser vice. MODEL SERIAL[...]

[...]

30 Español Extraccióndelcabezaldecepillo(gura4) 1. Gire el cabezal del cepillo y alinee las marcas. 2. Para extraer el cepillo, tire de él. Precaución • Si tira del cabezal del cepillo mientras está sujeto, el cabezal del cepillo o la unidad principal pueden sufrir daños. Nota • Cuando los restos de dentífrico endure[...]