Makita 6932 manuale d’uso

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cor dless Impact Driver MODEL 6932FD 004340[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA003-2 (FOR ALL BA TTER Y OPERA TED T OOLS ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic sh[...]

3 SA VE THESE INSTR UCTIONS Wo r k A r e a 1. Keep y our work area clean and well lit. Cluttered benches and dark areas invite acci- dents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pow e r tools create sparks which may ignite the dust or fumes. 3. Keep bystander s, childre[...]

4 18. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. 19. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool ser- viced befo[...]

5 SYMBOLS USD302-1 The f ollowings show the symbols used f or tool. V ....................... volts ................... direct current ................... no load speed .../min ................ rev olutions or reciprocation per minute ................ number of b low IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CAR TRIDGE USC001-3 [...]

6 11 . Do not disassemble charger or battery cartridge; take it to a qualified ser viceman when service or repair is required, Incor- rect reassembly ma y result in a risk of electric shock or fire. 12. T o reduce risk of electric shock, unplug charger fr om outlet before attempting any maintenance or cleaning. T urning off con- trols will not redu[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. • T o remove the battery car tr idge , [...]

8 NO TE: • The batter y charger is f or charging Makita batter y car tridge. Ne ver use it f or other pur poses or f or other manuf acturer ’ s batteries. • When you charge a ne w batter y car tridge or a batter y car tridge which has not been used for a long period of time, it ma y not accept a full charge. This is a normal condition and doe[...]

9 Switch action CA UTION: • Bef ore inser ting the batter y car tridge into the tool, alwa ys check to see that the s witch trigger actuates properly and retur ns to the “ OFF ” position when released. T o star t the tool, simply pull the switch trigger . T ool speed is increased by increasing pressure on the s witch trigger . Release the s w[...]

10 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore carr ying out any work on the tool. Installing or removing driver bit or soc ket bit Use only the driver bit or soc ket bit shown in the figure . Do not use any other driver bit or soc ket bit. 1. T o install the bit, pull the sl[...]

11 OPERA TION The proper fa stening torque may diff er depending upon the kind or size of the scre w/bolt, the mater ial of the workpiece to be f astened, etc. The relation between fastening torque and f astening time is shown in the figures. Hold the tool firmly and place the point of the dr iv er bit in the screw head. Apply f orward pressure to [...]

12 torque coefficient, the class of bolt and the bolt length. 4. The manner of holding the tool or the material of dr iving position to be f astened will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fa stening torque. MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cart[...]

13 EN0001-1 Recyc ling the Battery The only wa y to dispose of a Makita batter y is to recycle it. The law prohibits an y other method of disposal. T o recycle the batter y: 1. Remov e the batter y from the tool. 2. a) T ake the batter y to y our nearest Makita F actor y Ser- vice Center or b) T ake the batter y to y our nearest Makita Authorized S[...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7[...]

18 Y our answer s to the following questions are appreciated. Date Purchased Model No . Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste[...]

19 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to [...]

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s[...]