Makita AN922 manuale d’uso

Pneumatic Framing Nailer 540 mm x 376 mm x 108 mm (21-114” x 14-3/4” x 4-1/4”) 446 mm x 376 mm x 108 mm (17-112” x 14-3/4” x 4-114”) 64 - 74 pes' - 84 pes' AN922 4.5 - 8.5 kgflcm2G (65 - 120 PSIG) 50 mm - 90 mm (2” - 3-1/2”) 8.5 mm (5116”) AN942 MODEL AN922 MODEL AN942 3.8 kg (8.4 Ibs) INSTRUCTION MANUAL 4ml AN922 LJ AN9[...]

IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. .For personal safety and proper operation and maintenance of the tool, read this instruction manual carefully before using the tool. Always wear safety[...]

*General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3. Do not activate the tool unless the tool is placed firmly against the workpiece. 4. Respect the tool as a working implement. 5. No horseplay. 6. Do not hold or carry the to[...]

.Only those involved in the work should be in the vicinity. Children especially must be kept away at all times. .There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, shutters should be used to contain noise. Do not play with the contact element: it prevents a[...]

*Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitro- gen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this tool, the tool will explode and cause serious injury. *Always check the tool for its overall condition and loose screws before operatio[...]

*Make sure that the trigger is locked when the change lever is set to the LOCK position. I *Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. Live wire I Gas Use only nails specified in this manual. The use of any othe[...]

Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. *Watch your footing and maintain your balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if[...]

Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting . *Do not point the ejection port at anyone in the vicinity. Keep hands and feet away from the ejection port area. I .. When the air hose [...]

Stop nailing operations immediately if you notice something wrong or out of the ordinary with the tool. .Always disconnect the air hose and remove all of the nails: 1. When unattended. 2. Before performing any maintenance or repair. 3. Before cleaning a jam. 4. Before moving the tool to a new location. Perform cleaning and maintenance right after f[...]

*Do not operate this tool if it does not contain a legible WARNING LABEL. *Do not modify tool without authorization from Makita. Ask Makita’s Factory or Authorized service center for periodical inspection of the tool. To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service Ce[...]

TOOL INSTALLATION INSTRUCTIONS AND USE Selecting compressor The air compressor must comply with the requirements of Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes [...]

Nose adapter CAUTION: Always lock the trigger and disconnect the hose before installing or removing the nose adapter. When nailing workpieces with easily-marred surfaces, use the nose adapter. It is stored in the holder on the reverse side of the magazine. Attach the nose adapter to the contact arm (see right). When not in use, store the nose adapt[...]

Unloading nailer CAUTION : Always disconnect the air hose before unloading the nailer. Pull the pusher lever to the rear. Return the pusher lever back while keeping the pusher depressed to disengage it from the strip of nails. I I Depress the nail stopper and remove the strip of nails from the magazine. Adjusting depth of nailing CAUTION: Pusher le[...]

Operation CAUTION: Make sure all safety systems are in working order before operation. 1) To drive a nail, you may place the contact element against the workpiece and pull the trigger, or 2) Pull the trigger first and then place the contact element against the workpiece. No. 1 method is for intermittent nailing, when you wish to drive a nail carefu[...]

Nails Handle nail strips and their box carefully. If the nail strips have been handled roughly, they may be out of shape or their connector breaks, causing poor nail feed. Avoid storing nails in a very humid or hot place or place exposed to direct sunlight. 1s[...]

MAINTENANCE CAUTION: Always disconnect the hose before attempting to perform inspection or maintenance. Maintenance of nailer Always check the tool for its overall condition and loose screws before operation. Tighten as re- quired. With tool disconnected, make daily inspection to assure free movement of the contact element and trigger. Do not use t[...]

When the tool is not to be used for an extended period of time, lubricate the tool using pneumatic tool oil and store the tool in a safe place. Avoid exposure to direct sunlight and/or a humid or hot environment. I M Maintenance of compressor, air set and air hose After operation, always drain the compressor tank and the air filter. If moisture is [...]

Keep the air hose away from heat (over 60°C, over 14OoF), away from chemicals (thinner, strong acids or alkalis). Also, route the hose away from obstacles which it may become dangerously caught on during operation. Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. L To maintain product SA[...]

(MEMO) 19[...]

MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight[...]