Miele G 2872 manuale d’uso

Operating Instructions Dishwasher G 2872 To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 07 724 170 en - US, CA[...]

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control panel ......................................................9 Display function ...................................................[...]

Additional options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Settings ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Drying Plus .......................................................4 4 Water hardness ......................[...]

WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only. Keep these operating instructions in a safe place a[...]

Installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Do not install or use a damaged dishwasher. A damaged appliance is da[...]

Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls. ~ Do not damage, sit or stand on the door or baskets of the dishwasher. Close the door when not in use. ~ Under certain conditions, hydrogen gas may be pro[...]

~ Advise the user of the AutoClose feature to avoid injuries by walking, bumping or knocking into the partially opened door. ~ Supervise children near the dishwasher to ensure fingers or other parts of the body are not caught when the AutoClose feature is in operation. Disposal of an appliance ~ If the appliance is removed from its installation sit[...]

a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Triple filter system h Data plate i Optical interface j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container Guide to the dishwasher 8[...]

Control panel a Selection buttons To select a menu point from this display, to change the displayed value (+/-) or to browse between menus. b Display See the following pages for more information. c Clear button To switch back to the previous menu level or to discard a selected setting. d d Delay Start button with indicator e K button (Information) [...]

Display function The following can be selected in the display – the wash program – the options – the start time – the settings J menu – information During a running program the display shows – the program name – the current time of day – the program sequence – the approximate remaining time – faults and messages To save energy t[...]

Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. ^ [...]

To open the door The door will open automatically at the end of the program to aid in the drying process. This function can be deactivated (see "Settings - Drying Plus"). ^ Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. To close [...]

Welcome screen ^ Turn the dishwasher on g . A Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting. } deutsch B Sprache F e } english (GB) OK } ^ Select the desired language and confirm with OK. The selected language is marked with a L check. Clock format Th[...]

Time of day setting The display changes automatically to the time of day setting. } + 12 :0 0 } - Please set the time of day OK } ^ Set the hours using the +/- controls and confirm with OK. Set the minutes and confirm. The settings will be saved after the first wash program has completed. Two messages Insufficient salt and Insufficient rinse aid ma[...]

Water softener Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. To achieve good cleaning results, the dishwasher needs soft water. Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water h[...]

Filling the salt container , Inadvertently filling the salt container with dishwashing detergent will damage the water softener. , Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. ^ Remove the lower basket and unscrew the salt container lid. When open[...]

Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. , Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergen[...]

Rinse aid refill message When the Insufficient rinse aid message first comes on, there will be enough rinse aid left fo r2-3 washes. ^ Refill rinse aid after the program has finished. If the "Tab" function is selected, the Insufficient rinse aid message will not come on. See "Settings J - Detergent". ^ Confirm with OK. The Insuf[...]

, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necess[...]

Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware – Plastic items that are not heat resistant – Copper, brass, tin or aluminum – Dis[...]

Split cutlery tray ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles between the holders. [...]

Upper basket , Always use the dishwasher with the upper and lower basket inserted. (except during the Tall items program). ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans. ^ Long items such as soup ladles, mixing spoons and long knives should be placed lying down across [...]

Adjustable cup racks ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. The height of the cup rack can be adjusted in two levels. ^ Pull the cup rack upwards and let it engage at the desired height. Coffee bar (depending on model) Glasses can be leaned against the coffee bar to allow a firm stand. ^ The bar can[...]

Universal support bar The support bar will hold tall glasses and stem-ware securely. ^ Fold the bar down and lean the desired glasses against it. ^ If desired, a section of the cutlery tray can be removed to allow for even taller glasses. Loading the dishwasher 24[...]

Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm. Take care when sliding the basket in and out in this position. ^ Slide out the [...]

Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small plates and saucers can also be arranged in the lower basket. Foldable spikes The foldable spikes can be used for small plates and saucers. Two rows of spikes can be folded down, to create more room for larger dishware, e.g. pots, pans and bowl[...]

Removable spike insert The spike insert can be removed in order to make room for larger tableware or to use a different insert. Removing the insert a ^ To remove the insert, gently pull the handle upwards. Replacing the insert b ^ Slide the hitches of the insert under the struts of the lower basket. ^ Push down on the handle to snap the insert into[...]

Removing the insert a : ^ To remove the insert, gently pull the handle upwards. Inserting the insert b : ^ Place the insert into the lower basket. ^ Slide the hitches of the insert under the struts of the lower basket. ^ Push down on the handle to snap the insert into position. Vase / Bottle insert (depending on model) The vase / bottle insert can [...]

Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine. Glassware insert GGO To wash long stemmed glassware, attaches to the upper basket Cappuccinatore insert GCEO To wash the parts of the Cappuccinatore (milk froth mug supplied wit[...]

Detergent , Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. , Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. Con[...]

Adding detergent ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in com[...]

Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if closed. ^ Turn the dishwasher on g . The main menu shows in the display. If the memory function is selected, the last selected program is displayed. See "Settings J - Memory". } Normal Main menu r } Pots & Pans Selecting a program Ch[...]

Program When to use Program sequence Pre rinse Main wash Interim rinse Final rinse Drying 12 1 2 Normal For normally soiled dishware with dried on food xxx xx Pots & Pans For normally soiled pots & pans with dried on food , and heavily soiled dishware, use 120% detergent recommended xx x x x China & Crystal For temperature sensitive gla[...]

Program When to use Program sequence Pre-rinse Main wash Interim rinse Final rinse Drying 12 1 2 Light Soiling For lightly soiled dishware, e.g. party dishware xx x x Energy Saver The water intake temperature must be 115°F (45°C) for light to normally soiled dishware xx x x x Plastics To gently clean dishwasher safe plastics and plastic toys xx x[...]

The detergent type can now be set. You can choose between powder, gel or Tabs. See "Settings J - Tab". Selecting options Options can be added to the selected program. ^ Select the Options menu. The display shows the available options for the selected program. Available options: Turbo: – For shortening the program duration. To achieve op[...]

Starting a program ^ Select Start. The display shows Close the door. To select another program or to add options, select Back and cancel the program with Cancel. ^ Start the program by closing the door. The optical interface lights to indicate that a program is running. The program starts and Dishes can be added appears in the display. As long as t[...]

At the end of a program At the end of a program the optical control light flashes slowly with the door closed. The optical function light goes out one hour after the end of a program. At the end of a program the display shows Program finished or Drying plus with the door slightly open (if activated). , The steam being released at the end of the pro[...]

Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. Sensor Wash 1:32 h 12:00 Main wash Cancellation } ^ Select Cancellation and confirm with OK. The program is canceled. Sensor Wash 12:00 Program finished Main menu } ^ Select Main menu. The[...]

Delay start The starting time of a program can be delayed between 15 minutes and 24 hours. The start can be delayed in 15-minute-increments. When using the "Delay Start" function make sure that the detergent compartment is dry before adding detergent, use a cloth if necessary. The detergent might stick together and not get completely rins[...]

^ Confirm with OK. The display changes to the program menu. ^ Select Start. ^ Close the door. The program starts automatically at the selected time. The indicator d goes out. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed. Proceed as follows: ^ Open the door. ^ Select Cancel a[...]

The "Settings J " menu allows you to adjust standard settings Opening the Settings J menu ^ Turn the dishwasher on by pressing the g button. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. See "Settings J - Memory". Switch to the main menu by pressing "Clear&qu[...]

Language J The display contents can be shown in different languages. The displayed language can be changed by the submenu Language J . ^ Select the desired language and confirm with OK. The flag behind the word Language J serves as a guide when an unfamiliar language is selected. Select the respective menu with a flag until the submenu Language J a[...]

Detergent To achieve best results the used detergent can be set on your dishwasher. The selections available are "Powder", "Gel" and "Tab". The program cycle sequence will be adjusted for the selected detergent. Depending on the program the program running time could increase. Powder When using powder detergent, salt a[...]

Drying Plus The Drying plus function automatically opens the door slightly at the end of a program, in order to improve the drying process. This function can also be deactivated. ^ Select the desired setting and confirm with OK. Water hardness The water hardness level set can be viewed under the submenu "Water hardness". ^ Press "OK&[...]

Rinse aid For best results the rinse aid dosage can be adjusted. The dosage can be set between 0 and 6 ml. The dosage set by default to 3 ml of rinse aid per program. – Use a higher setting if spots appear on dry glassware. – Use a lower setting if streaking appears on dishes or glasses. ^ Use the +/- buttons to selected the desired rinse aid a[...]

Reorganize program list The order of the programs in the program list can be reorganized. The two most frequently used programs can be saved to the first two positions. } Sensor Wash B e } Cancel Select program for position 1 Continue } ^ Select with e the program which you would like to save to the first position of the main menu. Confirm the sele[...]

Save options Additional options can be selected for some programs, e.g. extended drying. See "Use - Selecting options". Save options allows you to save the selected options for future use of the program. This function is turned off by default. ^ Select the desired setting and confirm with OK. Temperature The temperature can be displayed i[...]

Buzzer When the buzzer is activated, a tone sounds at the end of a program and if a fault occurs. The buzzer at the end of a program is turned on by default. Buzzer at the end of a program The buzzer at the end of a program sounds five times in intervals with a brief break in between. The buzzer sounds up to one hour if the dishwasher in not turned[...]

Button tone A tone will sound when a button is pressed. The volume can be set to seventeen different levels. It is set to level 8 by default. ^ Select the desired setting and confirm with OK. Brightness The display brightness can be adjusted in 17 levels. The brightness is set to level 9 by default. ^ Select the desired brightness and confirm with [...]

Dealer Demo modes are only for showrooms. The dishwasher has three demo programs for showrooms. The programs "Demo mode" and "Endless demo mode" show the use and function range of the dishwasher. – Demo mode: The program is started by pressing any button. It runs once and must be started again. – Endless demo mode: The progr[...]

Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem. For inform[...]

With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue Possible fault Solution The program does [...]

Issue Possible fault Solution The optical interface flashes fast, the buzzer sounds or the display shows the fault: A technical problem occurred. Turn the machine off, close the water faucet and call Technical Service. There may be a technical fault. – Turn the dishwasher off by touching the o control. After a few seconds: – Turn the dishwasher[...]

Problems water intake/drain Issue Possible fault Solution The optical interface flashes fast, the buzzer sounds and the display shows the fault: No water intake The water supply is closed. Open the water supply all the way. Fault water intake FXX Before fixing the fault: – Turn the dishwasher off o . Fault F12/F13: Fault in the water intake. – [...]

Issue Possible fault Solution The optical interface flashes fast. The program "Energy Saver" displays the fault: Water intake temp. too low The intake water does not have a minimum temperature of 115°F (45°C). See "Plumbing - Connection to the water supply". – Restart the program. – If the fault is displayed again, use a d[...]

General problems with the dishwasher Issue Possible fault Solution The display turns off. The dishwasher has gone into "Standby" mode to save energy. Touch any control. The display turns on again. The display shows the following: Middle spray arm blocked or Lower spray arm blocked The middle or lower spray arm is blocked by dishware. Open[...]

Issue Possible fault Solution Detergent is left in the dispenser at the end of a program. The dispenser was damp when detergent was added. Dry the dispenser before adding detergent. The detergent lid cannot be closed properly. Detergent residue is blocking the catch. Remove the residue. The door and the interior walls are still wet after a program [...]

Sounds Issue Possible fault Solution There is a knocking noise in the wash cabinet. The spray arm is hitting an item in the basket. Interrupt the program, rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet. Items are not secure in the wash cabinet. Interrupt the program and rearrange loose pieces. There is a knoc[...]

Poor cleaning results Issue Possible fault Solution The dishes are not clean. The dishes were not loaded correctly. See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program, see "Program Guide". Stubborn but normal soiling (e.g. coffee, tea). Use the function "Adjust Sensor Wash&quo[...]

Issue Possible fault Solution Dishes are not dry, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. Increase the dosage, refill the reservoir or switch the rinse aid product when refilling, see "Before using for the first time". Dishes were taken out too soon. Leave dishes in longe[...]

Issue Possible fault Solution Glasses are discolored and the film cannot be wiped off. Detergent deposits. Use a different detergent. Clouding or etching on glasses. Possible causes may be : excessive rinse aid, incorrect water hardness level set, type and amount of detergent,. Any one or a combination of these faults may be to blame. See the relev[...]

10 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray Comparison Tests 62[...]

16 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray Comparison Tests 63[...]

Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to[...]

To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the mach[...]

66[...]

User Maintenance Instructions To prevent accidents and appliance damage, read these instructions before installation or use.[...]

Check and clean your dishwasher regularly. This will help avoid faults and problems. , Abrasive cleaning agents, all-purpose cleaners, thinner or ammonium cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. The wash cabinet[...]

Indicator reflector The reflector of the optical interface is located in the steam deflector beneath the counter top. ^ Clean as necessary with a damp cloth. Control panel ^ Clean the control panel as necessary with a damp cloth. , The appliance front and controls are not scratch proof. Remove spills immediately. Cleaning and Care 69[...]

Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones, etc.). During normal use, the filter system is self-cleaning. , The machine must not be used without all the filters in p[...]

To clean the underside of the filter the flap must be opened. ^ Push the clips together a and open the flap b . ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Lock the filter by turning the handle clockwise. , The triple filter system must be inserted an[...]

Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift[...]

Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’s shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet. , The plastic housing of the water connection contains electrical wiring. Do not cut the intak[...]

Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. ^ Tilt the lo[...]

Installation Instructions Please refer to the Installation Diagram supplied with these instructions. To comply with IEC sound testing protocols, please contact Miele for additional instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.[...]

, Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data pla[...]

Waterproof system All Miele dishwashers have a safety valve located on the incoming water line and a sealed underside with a water sensor. If a fault occurs, the water intake is stopped and the drain pump is activated. Connection to the water supply , Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperatu[...]

Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maxi[...]

79[...]

Alteration rights reserved / 1711 G 2872 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION. M.-Nr. 07 724 170 / 05[...]