Mitsubishi Electronics BAC-HD150 manuale d’uso

Content s Page Safety Precautions ............................................ 2 1. Specifications ............................................ 4 1-1. Product Specificat ions ..................... 4 1-2. External dimensio ns......................... 4 1-3. Power supply function to the M-NET transmission line ... ........................... 5 2. Sam[...]

- 2 - Safety Precautions • Thoroughly read the foll owing safety precautions prior to installation. • Observe these precautions ca refully to ensure safety . • After reading this manual, p ass the manual on to the end user to retain for future reference. • The users should keep this manual for future reference an d refer to it as necessary [...]

- 3 - General caution Relocating/Rep airing unit s T ransporting units/Unit inst allation Electric work General caution CAUTION Import ant Do not inst all the unit in environments where large amount s of oil (including mach ine) or acidic/alkaline chemical sprays are present. These types of subst ances may cause device performance to be reduced and[...]

- 4 - 1-1. Product Specifications 1-2. External dimensions 1 S pecifications Items Sp e c Power source Rated input 100-240 V AC ± 10 % 0.4-0.3 A 50/60 Hz Fuse 250 V AC 3.15 A T ime-delay type (IEC127-2 S.S.5) Interface Rated output of the power supply to M-NET transmission lines 22-30 VDC LAN 10Base-T or 100Base-TX (LAN2 is for future use.) Ambien[...]

- 5 - 1-3. Power supply function to the M-NET transmission line BAC-HD150 has a built-in function to supply power to the M-NET transmission line. (power supply coefficient: 6) When power is supplied from BAC-HD150, the types of system controllers listed in the table below are connect able. T able 1 Power consumption co efficient of the controller T[...]

- 6 - The figure below only shows the transmission line connections. Power supply lines are omitted. 2 Sample system configuration Note Use a switching HUB. TB7 TB3 ME MA K TB7 TB3 MA K R2 TB7 TB3 MA MA [000] [051] [001] [002] [006] [057] [056] [007] [008] [009] [010] [003] [004] [005] [106] [1 1] [12] [13] [13] [213] [14] [15] [15] [16] BACnet HUB[...]

- 7 - Q Address setting for various devices: The sa me address cannot be used more than once within the same system of the BM ADAPTER (BAC-HD150). (K-control unit s and K-co ntrol remote control addresses are excluded.) * Main and sub system controllers (M-NET) BAC-HD150 can only be used as th e main system controller , but not as a sub system cont[...]

- 8 - Note The system cannot be config ured in the following way . Groups that are not under the control of a main SC cannot be controlled from a sub SC. Each group cannot be under the co ntrol of two or more main SC. Sub SC cannot be under the cont rol of two or more main SC. Group Group Group Main SC Sub SC Group Group Group Main SC 1 Main SC 2 G[...]

- 9 - 3-1. Required p art s The following parts are requ ired to inst all the unit. 3I n s t a l l a t i o n Required part s S pecification Power cable/ Protective earth cable Power supply cable of appliances shall not be lighter than design 245 IEC 57 or 227 IEC 57. Cable size:0.75mm² to 2mm² M-NET transmission line Shielded cable • CPEVS: φ [...]

- 10 - 3-2. M-NET transmission line length • Connect the BAC-HD150 to the tr ansmission line for centralized co ntrol (TB7 on the outdoor unit). • There should only be one power supply so urce within a single transmission circuit. The factory setting is that power is not supplied from the BAC-HD150. • Connect the shield of the M-NET transmiss[...]

- 1 1 - 3-3. Inst allation • Leave enough space around the un it to allow for an installati on/uninsta llation of the cover . • Screw down the cover with M4 scr ews as shown in the figure below . Be sure to fix the four corner s to prevent it from falling. • Install on the control panel with an ef fective depth of at least 105mm (4- 3 / 16 in[...]

- 12 - 4-1. Inst alling and uninst alling the cover Unscrew the three screws on the cover to re move it as shown in the figure below . Reinstall the cover using the thre e screws that were unscrewed. 4-2. Connecting the power cable and protective earth cable • Connect the power cable and the protective earth cable as shown in the figure below . U[...]

- 13 - 4-3. Connecting the M-NET transmission lines (1) Supplying power to the M-NET transmission line from the BAC-HD150 Connect the M-NET transmission lines and the power jumper as shown in the figure below . (2) T o not supply power to the M-NE T transmission line from the BAC-HD150 Connect the M-NET transmission lines and the power jumper as sh[...]

- 14 - 4-4. Connecting the LAN cable • Make sure that the LAN cable is long enough to reach the LAN1 connector on the BAC-HD150. Leave the LAN cable disconnected until all the initial se ttings for the BAC-HD150 (IP address setting etc. ) have been completed. • Connect the BAC-HD150 (LAN1) and the building management system via a HUB. • The m[...]

NOTE: This equipment has been test ed and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide re sonable protection against harmful interference in a residential instal lation. This equipment generates, us es and can radiate radio frequency energy and, if not insta[...]

HEAD OFFICE: TOKYO BLDG . , 2-7-3, MARUNOUCHI, CHIYODA-KU, TO KYO 100-8310, JAP AN Authorized representative in EU: MITSUBISHI ELECTR IC EUROPE B.V . HARMAN HOUSE, 1 GEORGE STREET , UXBRIDGE, MIDDLESEX UB8 1QQ, U.K. WT05543X01 Printed in Japan Recycled Paper Please be sure to put the contac t address/telephone number on this manual before handing i[...]