NEC 2090 manuale d’uso

MultiSync LCD2090UXi SpectraV iew 2090 User’ s Man ual[...]

Index W arning, Caution ............................................................................................................... ......... English-1 Declaration .................................................................................................................................. English-1 Canadian Depar tment of Communications Co[...]

English English-1 W ARNING CA UTION CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGA GE THE PO WER T O THE UNIT , PLEASE DISCONNECT THE PO WER CORD FROM THE AC OUTLET .DO NO T REMO VE CO VER (OR BACK). NO USER SER VICEABLE P AR TS INSIDE. REFER SER VICING TO QU ALIFIED SER VIC[...]

English-2 Canadian Depar tment of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations . C-UL: Bears the C-UL Mar k and is in compliance with Canadian Saf ety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Inf ormation 1 . Use the attached [...]

English English-3 Contents Y our new NEC monitor box* should contain the f ollowing: • MultiSync LCD2090UXi or SpectraView 2090 monitor with tilt/s wivel/pivot/height adjust stand • P ower Cord (European Continental) • P ower Cord (UK: Black model only) • Video Signal Cable (15-pin mini D-SUB male to D VI-A) • Video Signal Cable (D VI-D t[...]

English-4 Figure C.1 Figure C.2 Highest Stand P osition Quic k Star t T o attach the LCD monitor to your system, f ollow these instructions: 1. T ur n off the power to your computer . 2. For the PC or MA C with DVI digital output: Connect the D VI signal cable to the connector of the display card in y our system ( Figure A.1 ). Tighten all screws. [...]

English English-5 Figure E.1 V acation Switch P ower Button Figure C.3 Figure D .1 Figure D .2 Figure C.4 7. Hold all cables firmly and place the cable cov er onto the stand ( Figure D.1 ). T o remove the cab le cover , lift the cov er off as shown in Figure D .2 . 8. Connect one end of the power cord to the A C inlet on the back of the monitor and[...]

English-6 Tilt Grasp top and bottom sides of the monitor screen with y our hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with y our hands and adjust the s wivel as desired ( Figure TS.2 ). NO TE: Handle with care when tilting the monitor screen. Figure TS.2 Screen Rotation Before rot[...]

English English-7 Figure S.1 4. Place one hand around the base and one hand on the Quick Release Le ver . Move the Quic k Release Lev er in the direction indicated by the arro ws ( Figure S.2 ). 5. Lift up the bottom of the stand to unhook it from the monitor ( Figure S.3 ). The monitor can now be mounted using and alter nate method. Rev erse proce[...]

English-8 Contr ols OSM (On-Screen Manager) control b uttons on the front of the monitor function as follo ws: T o access OSM menu, press any of the control b uttons (EXIT , LEFT , RIGHT , UP , DO WN). T o change signal input, press the SELECT button. NO TE: OSM must be closed in order to change signal input. * The “ LEFT/RIGHT ” and “ UP/DO [...]

English English-9 ECO MODE Decreases the amount of power consumed b y reducing the brightness lev el. 1: Decreases the brightness by 25%. 2: Decreases the brightness by 50%. CUST OM: Decreases the br ightness le vel as determined by the user . Ref er to the Advanced OSM menu f or custom setting instructions. A UT O BRIGHTNESS There are three settin[...]

English-10 A UT O FINE (Analog input only) This function automatically and periodically adjusts the “ FINE ” setting for change in signal condition. This function adjusts appro ximately ev er y 33 minutes. EXP ANSION Sets the zoom method. FULL: The image is e xpanded to 1600 x 1200, regardless of the resolution. ASPECT : The image is expanded w[...]

English English-11 OFF TIMER Monitor will automatically power-do wn when the end user has selected a pre-deter mined amount of time. Bef ore powering off, a message will appear on the screen asking the user if the y want to dela y the tur n off time by 60 minutes . Press any OSM b utton to delay the turn off time. IPM The Intelligent P ower Manager[...]

English-12 RESOLUTION NO TIFIER This optimal resolution is 1600 x 1200. If ON is selected, a message will appear on the screen after 30 seconds, notifying y ou that the resolution is not at 1600 x 1200. HO T KEY Y ou can adjust the br ightness and contrast directly . When this function is set to ON, you can adjust the brightness with “ Left ” o[...]

English English-13 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NO TE THE FOLLO WING WHEN SETTING UP AND USING THE LCD COLOUR MONITOR: • DO NO T OPEN THE MONIT OR. There are no user serviceable par ts inside and opening or removing cov ers may e xpose you to dangerous shoc k hazards or other risks. Refer all [...]

English-14 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN Y OU POSITION THE MONITOR: • For optim um performance, allow 20 min utes for w ar m-up. • Adjust the monitor height so that the top of the screen is at or slightly below ey e level. Y our eyes should look slightly do[...]

English English-15 Specifications Monitor Specifications MultiSync LCD2090UXi and Notes SpectraView 2090 Monitor LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) liquid View able Image Size: 51 cm/20.1 inches cr ystal display (LCD); 0.255 mm dot pitch; Native Resolution (Pix el Count): 1600 x 1200 280 cd/m 2 white lu[...]

English-16 Features Ambix3 T echnology: T riple input technology allowing up to 3 input sources to be connected to a single monitor . The D VI-I connector suppor ts both analog and digital input signals. Legacy analog input is suppor ted using a traditional 15-pin VGA connector . Ambix3 provides traditional technology compatibility f or analog as w[...]

English English-17 T roub leshooting No picture • The signal cable should be completely connected to the displa y card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position. • F ront P ower Switch and computer pow er switch should be in the ON position. • Check to [...]

English-18 Appendix If you need detailed inf ormation about the controls, please use the advanced menu. <How to use the adv anced menu> • T ur n off your monitor . • T ur n on your monitor by pushing the “ POWER ” and “ SELECT ” button at the same time f or at least one second simultaneously . Then press the control buttons (EXIT [...]

English English-19 T ag3 A uto Adjust Automatically adjusts the Image P osition and H.Size settings and Fine settings. (Analog input only) Press “ SELECT ” to activate A uto Adjustment. Signal Adjust Deter mines when the auto adjustment is activated automatically . (Analog input only) The choices are “ SIMPLE ” and “ FULL ” . Press “ [...]

English-20 H.ZOOM The image is expanded from 1 to 3 times in the horizontal (H. EXP ANSION) direction by (A vailab le in Custom 0.01 increments. Expansion mode only) V .ZOOM The image is expanded from 1 to 3 times in the v er tical (V . EXP ANSION) direction by (A vailab le in Custom 0.01 increments. Expansion mode only) ZOOM POS. Sets the point fr[...]

English English-21 Video Detect Selects the method of video detection when more than one computer is connected. Press “ Left ” or “ Right ” to select. FIRST: The video input has to be switched to “ FIRST ” mode. When current video input signal is not present, then the monitor searches for a video signal from the other video input por t.[...]

English-22 OSM Lock Out This control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the Loc k Out mode, a screen will appear indicating the OSM controls are lock ed out. There are three types of OSM LOCK OUT: OSM LOCK OUT with BRIGHTNESS and CONTRAST control: T o activate the OSM Loc k Ou[...]

English English-23 Screen Sav er Use the SCREEN SA VER to reduce the risk of image persistence. MO TION (Default OFF): Screen image is reduced to 95% size and mov es periodically in 4 directions in order to reduce the risk of image retention. Screen image can be set to mov e per iodically in inter vals from 10 to 900 seconds in 10 seconds increment[...]

English-24 T agC Schedule Programs the monitor ’ s working schedule. Schedule the power on and power off with hour and a day of the w eek. Also sets the input por t. This OSM can ’ t remov e except EXIT . Using the “ SCHEDULE ” function allows you to set up to se ven diff erent scheduled time inter vals when the LCD Monitor will be activ at[...]

English English-25 Using the A uto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly . The pur pose of this function is to make t[...]

English-26 TCO ’ 03 Congratulations! The displa y you ha ve just purchased carries the TCO ’ 03 Displa ys label. This means that your displa y is designed, manuf actured and tested according to some of the strictest quality and environmental requirements in the world. This makes f or a high performance product, designed with the user in f ocus [...]

English English-27 NEC DISPLA Y SOLUTIONS is strongly committed to en vironmental protection and sees recycling as one of the company ’ s top prior ities in tr ying to minimize the burden placed on the en vironment. W e are engaged in developing en vironmentally- friendly products, and alwa ys strive to help define and comply with the latest inde[...]