NEC LCD1770GX manuale d’uso

MultiSync LCD1770GX User’ s Manual[...]

Inde x W arning, Caution ............................................................................................................... .......... English-1 Declaration ................................................................................................................................... English-1 Canadian Depar tment of Communications[...]

English English-1 W ARNING CA UTION CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE PO WER CORD IS UNPLUGGED FROM W ALL SOCKET . TO FULL Y DISENGA GE THE POWER T O THE UNIT , PLEASE DISCONNECT THE POWER CORD FR OM THE A C OUTLET .DO NOT REMO VE COVER (OR BA CK). NO USER SER VICEABLE P AR TS INSIDE. REFER SER VICING T O QUALIFIED SER VICE[...]

English-2 Canadian Depar tment of Comm unications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations . C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1 . Use the attached sp[...]

English English-3 Contents Y our new NEC MultiSync LCD monitor box* should contain the f ollowing: • MultiSync LCD1770GX monitor with tilt/s wivel/piv ot/height adjust stand • P ower Cord • Video Signal Cable • USB Cable • User ’ s Manual • Cable Cover • CD ROM (includes complete User ’ s Manual in PDF f ormat). T o see the User ?[...]

English-4 Quic k Star t T o attach the MultiSync LCD monitor to your system, f ollow these instructions: 1. T ur n off the po wer to your computer . 2. For the PC or MA C with DVI digital output: Connect the D VI signal cable (not included) to the connector of the displa y card in your system ( Figure A.1 ). Tighten all screws . For the PC with Ana[...]

English English-5 Inser t T op First Then Bottom 6. Place D VI cable and po wer cab le into the specific hooks indicated in Figure C.3 . 7. Place the D-Sub and USB cables into the specific hooks indicated in Figure C.4 . 8. Make sure all cab les are resting flat against the stand ( Figure C.4 ). 9. Hold the all cables firmly and place the cable cov[...]

English-6 Figure S.1 Remo ve Monitor Stand f or Mounting T o prepare the monitor for alternate mounting pur poses: 1. Place hands on each side of the monitor and lift up to the highest position. Remov e the cable co ver ( Figure S.1 ). 2. Disconnect all cables . 3. Place monitor f ace down on a non-abrasiv e surface ( Figure S.2 ). 4. Remov e the 2[...]

English English-7 Figure S.3 Figure S.4 5. Lift up the stand to unlatch the upper hooks and remov e the stand ( Figure S.3 ). 6. Remov e the 2 screws on the top of the monitor ( Figure S.4 ). The monitor is now ready f or mounting in an alter nate manner . 7. Connect the cables to the bac k of the monitor. 8. Rev erse this process to re-attach stan[...]

English-8 Contr ols OSM (On-Screen Manager) contr ol b uttons on the fr ont of the monitor function as f ollows: T o access OSM menu, press any of the control b uttons (MENU/EXIT , Left, Right, Down, Up). T o change signal input, press the SELECT button. T o change D V MODE, press the RESET/D V MODE button. NO TE: OSM must be closed in order to cha[...]

English English-9 Colour Contr ol System Colour Control System: Six colour presets select the desired colour setting (sRGB and NA TIVE colour presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or[...]

English-10 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NO TE THE FOLLO WING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOUR MONITOR: • DO NO T OPEN THE MONITOR. There are no user ser viceab le par ts inside and opening or removing co vers ma y expose you to dangerous shoc k hazards or other r isks. Refer[...]

English English-11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN Y OU POSITION THE MONIT OR: • F or optimum perf ormance, allow 20 minutes f or warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below e ye le vel. Y our eyes should look sli[...]

English-12 Specifications Monitor Specifications MultiSync LCD1770GX Monitor Notes LCD Module Diagonal: 43.2 cm/17.0 inches Active matrix; thin film transistor (TFT) View able Image Siz e: 43.2 cm/17.0 inches liquid cr ystal displa y (LCD); 0.264 mm dot Native Resolution (Pix el Count): 1280 x 1024 pitch; 420 cd/m 2 white luminance; 500:1 contrast [...]

English English-13 Features Thin-frame design creates more desktop space f or you to work and pla y , while the flat screen ’ s crisp, bright images and cr ystal- clear text deliv er a comfortable viewing e xper ience. No T ouch Auto Adjust automatically adjusts y our optimal image settings upon initial power-on. Colour Control System allows y ou[...]

English-14 T r oubleshooting No picture • The signal cable should be completely connected to the displa y card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position. • F ront P ower Switch and computer po wer s witch should be in the ON position. • Check to mak e s[...]

English English-15 TCO’03 Congratulations! The displa y you hav e just purchased carr ies the TCO ’ 03 Displays label. This means that your displa y is designed, manuf actured and tested according to some of the strictest quality and environmental requirements in the world. This mak es f or a high performance product, designed with the user in [...]

English-16 Manufacturer’ s Recyc ling and Energy Inf ormation NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the compan y ’ s top prior ities in trying to minimize the burden placed on the en vironment. We are engaged in de veloping environmentally- friendly products, and alwa ys str iv e t[...]